rename CFG_ macros to CONFIG_SYS

[people/ms/u-boot.git] / board / pm854 / pm854.c

 /*
 * Copyright 2004 Freescale Semiconductor.
 * (C) Copyright 2002,2003, Motorola Inc.
 * Xianghua Xiao, (X.Xiao@motorola.com)
 *
 * (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
 *
 * See file CREDITS for list of people who contributed to this
 * project.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 * MA 02111-1307 USA
 */


#include <common.h>
#include <pci.h>
#include <netdev.h>
#include <asm/processor.h>
#include <asm/mmu.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_ddr_sdram.h>
#include <spd_sdram.h>

#if defined(CONFIG_DDR_ECC)
extern void ddr_enable_ecc(unsigned int dram_size);
#endif

void local_bus_init(void);
void sdram_init(void);
long int fixed_sdram(void);


int board_early_init_f (void)
{
#if defined(CONFIG_PCI)
    volatile ccsr_pcix_t *pci = (void *)(CONFIG_SYS_MPC85xx_PCIX_ADDR);

    pci->peer &= 0xffffffdf; /* disable master abort */
#endif

    return 0;
}

int checkboard (void)
{
	puts("Board: MicroSys PM854\n");

#ifdef CONFIG_PCI
	printf("    PCI1: 32 bit, %d MHz (compiled)\n",
	       CONFIG_SYS_CLK_FREQ / 1000000);
#else
	printf("    PCI1: disabled\n");
#endif

	/*
	 * Initialize local bus.
	 */
	local_bus_init();

	return 0;
}


phys_size_t
initdram(int board_type)
{
	long dram_size = 0;

	puts("Initializing\n");

#if defined(CONFIG_DDR_DLL)
	{
	    volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
	    int i,x;

	    x = 10;

	    /*
	     * Work around to stabilize DDR DLL
	     */
	    gur->ddrdllcr = 0x81000000;
	    asm("sync;isync;msync");
	    udelay (200);
	    while (gur->ddrdllcr != 0x81000100)
	    {
		gur->devdisr = gur->devdisr | 0x00010000;
		asm("sync;isync;msync");
		for (i=0; i<x; i++)
		    ;
		gur->devdisr = gur->devdisr & 0xfff7ffff;
		asm("sync;isync;msync");
		x++;
	    }
	}
#endif

#if defined(CONFIG_SPD_EEPROM)
	dram_size = fsl_ddr_sdram();
	dram_size = setup_ddr_tlbs(dram_size / 0x100000);
	dram_size *= 0x100000;
#else
	dram_size = fixed_sdram ();
#endif

#if defined(CONFIG_DDR_ECC)
	/*
	 * Initialize and enable DDR ECC.
	 */
	ddr_enable_ecc(dram_size);
#endif
	puts("    DDR: ");
	return dram_size;
}


/*
 * Initialize Local Bus
 */

void
local_bus_init(void)
{
	volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
	volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);

	uint clkdiv;
	uint lbc_hz;
	sys_info_t sysinfo;

	/*
	 * Errata LBC11.
	 * Fix Local Bus clock glitch when DLL is enabled.
	 *
	 * If localbus freq is < 66Mhz, DLL bypass mode must be used.
	 * If localbus freq is > 133Mhz, DLL can be safely enabled.
	 * Between 66 and 133, the DLL is enabled with an override workaround.
	 */

	get_sys_info(&sysinfo);
	clkdiv = lbc->lcrr & 0x0f;
	lbc_hz = sysinfo.freqSystemBus / 1000000 / clkdiv;

	if (lbc_hz < 66) {
		lbc->lcrr = CONFIG_SYS_LBC_LCRR | 0x80000000;	/* DLL Bypass */

	} else if (lbc_hz >= 133) {
		lbc->lcrr = CONFIG_SYS_LBC_LCRR & (~0x80000000); /* DLL Enabled */

	} else {
		/*
		 * On REV1 boards, need to change CLKDIV before enable DLL.
		 * Default CLKDIV is 8, change it to 4 temporarily.
		 */
		uint pvr = get_pvr();
		uint temp_lbcdll = 0;

		if (pvr == PVR_85xx_REV1) {
			/* FIXME: Justify the high bit here. */
			lbc->lcrr = 0x10000004;
		}

		lbc->lcrr = CONFIG_SYS_LBC_LCRR & (~0x80000000); /* DLL Enabled */
		udelay(200);

		/*
		 * Sample LBC DLL ctrl reg, upshift it to set the
		 * override bits.
		 */
		temp_lbcdll = gur->lbcdllcr;
		gur->lbcdllcr = (((temp_lbcdll & 0xff) << 16) | 0x80000000);
		asm("sync;isync;msync");
	}
}


#if defined(CONFIG_SYS_DRAM_TEST)
int testdram (void)
{
	uint *pstart = (uint *) CONFIG_SYS_MEMTEST_START;
	uint *pend = (uint *) CONFIG_SYS_MEMTEST_END;
	uint *p;

	printf("SDRAM test phase 1:\n");
	for (p = pstart; p < pend; p++)
		*p = 0xaaaaaaaa;

	for (p = pstart; p < pend; p++) {
		if (*p != 0xaaaaaaaa) {
			printf ("SDRAM test fails at: %08x\n", (uint) p);
			return 1;
		}
	}

	printf("SDRAM test phase 2:\n");
	for (p = pstart; p < pend; p++)
		*p = 0x55555555;

	for (p = pstart; p < pend; p++) {
		if (*p != 0x55555555) {
			printf ("SDRAM test fails at: %08x\n", (uint) p);
			return 1;
		}
	}

	printf("SDRAM test passed.\n");
	return 0;
}
#endif


#if !defined(CONFIG_SPD_EEPROM)
/*************************************************************************
 *  fixed sdram init -- doesn't use serial presence detect.
 ************************************************************************/
long int fixed_sdram (void)
{
  #ifndef CONFIG_SYS_RAMBOOT
	volatile ccsr_ddr_t *ddr= (void *)(CONFIG_SYS_MPC85xx_DDR_ADDR);

	ddr->cs0_bnds = CONFIG_SYS_DDR_CS0_BNDS;
	ddr->cs0_config = CONFIG_SYS_DDR_CS0_CONFIG;
	ddr->timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1;
	ddr->timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2;
	ddr->sdram_mode = CONFIG_SYS_DDR_MODE;
	ddr->sdram_interval = CONFIG_SYS_DDR_INTERVAL;
    #if defined (CONFIG_DDR_ECC)
	ddr->err_disable = 0x0000000D;
	ddr->err_sbe = 0x00ff0000;
    #endif
	asm("sync;isync;msync");
	udelay(500);
    #if defined (CONFIG_DDR_ECC)
	/* Enable ECC checking */
	ddr->sdram_cfg = (CONFIG_SYS_DDR_CONTROL | 0x20000000);
    #else
	ddr->sdram_cfg = CONFIG_SYS_DDR_CONTROL;
    #endif
	asm("sync; isync; msync");
	udelay(500);
  #endif
	return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024;
}
#endif	/* !defined(CONFIG_SPD_EEPROM) */


#if defined(CONFIG_PCI)
/*
 * Initialize PCI Devices, report devices found.
 */

#ifndef CONFIG_PCI_PNP
static struct pci_config_table pci_pm854_config_table[] = {
    { PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID, PCI_ANY_ID,
      PCI_IDSEL_NUMBER, PCI_ANY_ID,
      pci_cfgfunc_config_device, { PCI_ENET0_IOADDR,
				   PCI_ENET0_MEMADDR,
				   PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER
      } },
    { }
};
#endif


static struct pci_controller hose = {
#ifndef CONFIG_PCI_PNP
	config_table: pci_pm854_config_table,
#endif
};

#endif	/* CONFIG_PCI */


void
pci_init_board(void)
{
#ifdef CONFIG_PCI
	pci_mpc85xx_init(&hose);
#endif /* CONFIG_PCI */
}

int board_eth_init(bd_t *bis)
{
	cpu_eth_init(bis);	/* Intialize TSECs first */
	return pci_eth_init(bis);
}