arm: config: Enable CRC8 support in SPL on imx287 XEA board

[thirdparty/u-boot.git] / configs / imx28_xea_defconfig

CONFIG_ARM=y
CONFIG_SPL_SYS_THUMB_BUILD=y
CONFIG_ARCH_MX28=y
CONFIG_TEXT_BASE=0x40002000
CONFIG_SYS_MALLOC_F_LEN=0x800
CONFIG_SPL_GPIO=y
CONFIG_SPL_LIBCOMMON_SUPPORT=y
CONFIG_SPL_LIBGENERIC_SUPPORT=y
CONFIG_NR_DRAM_BANKS=1
CONFIG_SF_DEFAULT_SPEED=40000000
CONFIG_IMX_CONFIG=""
CONFIG_DM_GPIO=y
CONFIG_SPL_DM_SPI=y
CONFIG_DEFAULT_DEVICE_TREE="imx28-xea"
CONFIG_SPL_TEXT_BASE=0x1000
CONFIG_TARGET_XEA=y
CONFIG_SPL_MXS_PMU_MINIMAL_VDD5V_CURRENT=y
CONFIG_SPL_MXS_PMU_DISABLE_BATT_CHARGE=y
# CONFIG_SPL_MXS_PMU_ENABLE_4P2_LINEAR_REGULATOR is not set
CONFIG_SPL_MMC=y
CONFIG_SPL_SERIAL=y
CONFIG_SPL_STACK=0x20000
CONFIG_SPL_SYS_MALLOC_F_LEN=0x1000
CONFIG_SPL=y
CONFIG_ENV_OFFSET_REDUND=0x90000
CONFIG_SPL_SPI_FLASH_SUPPORT=y
CONFIG_SPL_SPI=y
CONFIG_SYS_LOAD_ADDR=0x42000000
CONFIG_SPL_PAYLOAD="u-boot.img"
CONFIG_TIMESTAMP=y
CONFIG_FIT=y
# CONFIG_BOOTMETH_EXTLINUX is not set
# CONFIG_BOOTMETH_VBE is not set
CONFIG_OF_BOARD_SETUP=y
CONFIG_USE_BOOTARGS=y
CONFIG_BOOTARGS="console=ttyAMA0,115200n8"
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="run ${bootpri} ; run ${bootsec}"
CONFIG_USE_PREBOOT=y
CONFIG_PREBOOT="run prebootcmd"
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_SPL_NO_BSS_LIMIT=y
CONFIG_SPL_BOARD_INIT=y
# CONFIG_SPL_RAW_IMAGE_SUPPORT is not set
CONFIG_SPL_SYS_MALLOC_SIMPLE=y
# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR=y
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x0
CONFIG_SUPPORT_EMMC_BOOT_OVERRIDE_PART_CONFIG=y
CONFIG_SPL_DMA=y
CONFIG_SPL_MMC_TINY=y
CONFIG_SPL_DM_SPI_FLASH=y
CONFIG_SPL_OS_BOOT=y
CONFIG_SPL_PAYLOAD_ARGS_ADDR=0x44000000
CONFIG_SPL_FALCON_BOOT_MMCSD=y
CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR=0x800
CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR=0x400
CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS=0x40
CONFIG_SPL_SPI_LOAD=y
CONFIG_SYS_SPI_U_BOOT_OFFS=0x10000
CONFIG_SPL_YMODEM_SUPPORT=y
CONFIG_HUSH_PARSER=y
CONFIG_SYS_MAXARGS=32
CONFIG_CMD_SPL=y
CONFIG_CMD_ASKENV=y
CONFIG_CMD_GREPENV=y
CONFIG_CMD_DM=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_MMC=y
CONFIG_CMD_MTD=y
# CONFIG_CMD_PINMUX is not set
CONFIG_CMD_SPI=y
CONFIG_CMD_DHCP=y
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_REGULATOR=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_CMD_MTDPARTS=y
CONFIG_DOS_PARTITION=y
CONFIG_OF_CONTROL=y
CONFIG_SPL_OF_CONTROL=y
CONFIG_OF_SPL_REMOVE_PROPS="pinctrl-0 pinctrl-names clock-names interrupt-parent interrupts"
CONFIG_SPL_OF_PLATDATA=y
# CONFIG_SPL_OF_PLATDATA_PARENT is not set
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_SPI_FLASH=y
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
CONFIG_USE_BOOTFILE=y
CONFIG_BOOTFILE="uImage"
CONFIG_USE_HOSTNAME=y
CONFIG_HOSTNAME="xea"
CONFIG_NET_RANDOM_ETHADDR=y
CONFIG_SPL_DM=y
CONFIG_DEVRES=y
CONFIG_MXS_GPIO=y
CONFIG_SUPPORT_EMMC_BOOT=y
CONFIG_MMC_MXS=y
CONFIG_MTD=y
CONFIG_DM_MTD=y
CONFIG_DM_SPI_FLASH=y
CONFIG_SF_DEFAULT_BUS=2
CONFIG_SPI_FLASH_SFDP_SUPPORT=y
CONFIG_SPI_FLASH_ISSI=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
# CONFIG_SPI_FLASH_USE_4K_SECTORS is not set
CONFIG_SPI_FLASH_MTD=y
CONFIG_PHYLIB=y
CONFIG_PHY_ADDR_ENABLE=y
CONFIG_PHY_ADDR=1
CONFIG_PHY_FIXED=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_MXS=y
CONFIG_DM_REGULATOR=y
CONFIG_DM_REGULATOR_FIXED=y
CONFIG_DM_REGULATOR_GPIO=y
CONFIG_SPECIFY_CONSOLE_INDEX=y
CONFIG_DM_SERIAL=y
CONFIG_SPI=y
CONFIG_DM_SPI=y
CONFIG_MXS_SPI=y
CONFIG_SPL_CRC8=y
# CONFIG_SPL_OF_LIBFDT is not set