[people/ms/u-boot.git] / include / configs / CCM.h

/*
 * (C) Copyright 2001-2005
 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
 *
 * See file CREDITS for list of people who contributed to this
 * project.
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 * MA 02111-1307 USA
 */

/*
 * configuration options, board specific, for Siemens Card Controller Module
 */

#ifndef __CONFIG_H
#define __CONFIG_H

#undef	CCM_80MHz			/* define for 80 MHz CPU only */

/*
 * High Level Configuration Options
 * (easy to change)
 */

#define CONFIG_MPC860           1   /* This is a MPC860 CPU ... */
#define CONFIG_CCM              1   /* on a Card Controller Module  */

#define CONFIG_8xx_CONS_SMC1    1   /* Console is on SMC1       */
#undef  CONFIG_8xx_CONS_SMC2
#undef  CONFIG_8xx_CONS_NONE

/*  ENVIRONMENT */

#define CONFIG_BAUDRATE         19200         /* console baudrate in bps    */
#define CONFIG_BOOTDELAY        2             /* autoboot after 2 seconds   */

#define CONFIG_IPADDR           192.168.0.42
#define CONFIG_NETMASK          255.255.255.0
#define CONFIG_GATEWAYIP        0.0.0.0
#define CONFIG_SERVERIP         192.168.0.254

#define CONFIG_HOSTNAME         CCM

#define CONFIG_LOADADDR         40180000

#undef	CONFIG_BOOTARGS

#define CONFIG_BOOTCOMMAND      "setenv bootargs " \
				"mem=${mem} " \
				"root=/dev/ram rw ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off " \
				"wt_8xx=timeout:3600; " \
				"bootm"

#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
#undef	CONFIG_SYS_LOADS_BAUD_CHANGE	/* don't allow baudrate change	*/

#define	CONFIG_WATCHDOG		1	/* watchdog enabled		*/

#undef	CONFIG_STATUS_LED		/* Status LED disabled		*/

#define	CONFIG_PRAM		512	/* reserve 512kB "protected RAM"*/

#define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/

#define	CONFIG_SPI			/* enable SPI driver		*/
#define	CONFIG_SPI_X			/* 16 bit EEPROM addressing	*/

/* ----------------------------------------------------------------
 * Offset to initial SPI buffers in DPRAM (used if the environment
 * is in the SPI EEPROM): We need a 520 byte scratch DPRAM area to
 * use at an early stage. It is used between the two initialization
 * calls (spi_init_f() and spi_init_r()). The value 0xB00 makes it
 * far enough from the start of the data area (as well as from the
 * stack pointer).
 * ---------------------------------------------------------------- */
#define CONFIG_SYS_SPI_INIT_OFFSET		0xB00

#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	5	/* 32-byte page size	*/


#define CONFIG_MAC_PARTITION		/* nod used yet			*/
#define CONFIG_DOS_PARTITION

/*
 * BOOTP options
 */
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_BOOTFILESIZE


/*
 * Command line configuration.
 */
#include <config_cmd_default.h>

#define CONFIG_CMD_BSP
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DATE
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_NFS
#define CONFIG_CMD_SNTP


/*
 * Miscellaneous configurable options
 */
#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
#define	CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt	*/
#if defined(CONFIG_CMD_KGDB)
#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
#else
#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
#endif
#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/

#define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on	*/
#define CONFIG_SYS_MEMTEST_END		0x00F00000	/* 1 ... 15MB in DRAM	*/

#define	CONFIG_SYS_LOAD_ADDR		0x00100000	/* default load address	*/

/* Ethernet hardware configuration done using port pins */
#define CONFIG_SYS_PA_ETH_RESET	0x0200		/* PA  6	*/
#define CONFIG_SYS_PA_ETH_MDDIS	0x4000		/* PA  1	*/
#define CONFIG_SYS_PB_ETH_POWERDOWN	0x00000800	/* PB 20	*/
#define CONFIG_SYS_PB_ETH_CFG1		0x00000400	/* PB 21	*/
#define CONFIG_SYS_PB_ETH_CFG2		0x00000200	/* PB 22	*/
#define CONFIG_SYS_PB_ETH_CFG3		0x00000100	/* PB 23	*/

/* Ethernet settings:
 * MDIO not disabled, autonegotiation, 10/100Mbps, half/full duplex
 */
#define CONFIG_SYS_ETH_MDDIS_VALUE	0
#define CONFIG_SYS_ETH_CFG1_VALUE	1
#define CONFIG_SYS_ETH_CFG2_VALUE	1
#define CONFIG_SYS_ETH_CFG3_VALUE	1

/* PUMA configuration */
#define CONFIG_SYS_PC_PUMA_PROG	0x0200		/* PC  6        */
#define CONFIG_SYS_PC_PUMA_DONE	0x0008		/* PC 12	*/
#define CONFIG_SYS_PC_PUMA_INIT	0x0004		/* PC 13	*/

#define	CONFIG_SYS_HZ		1000		/* decrementer freq: 1 ms ticks	*/

#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }

/*
 * Low Level Configuration Settings
 * (address mappings, register initial values, etc.)
 * You should know what you are doing if you make changes here.
 */
/*-----------------------------------------------------------------------
 * Internal Memory Mapped Register
 */
#define CONFIG_SYS_IMMR		0xF0000000

/*-----------------------------------------------------------------------
 * Definitions for initial stack pointer and data area (in DPRAM)
 */
#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
#define	CONFIG_SYS_INIT_RAM_END	0x2F00	/* End of used area in DPRAM	*/
#define	CONFIG_SYS_GBL_DATA_SIZE	64  /* size in bytes reserved for initial data */
#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

/*-----------------------------------------------------------------------
 * Address accessed to reset the board - must not be mapped/assigned
 */
#define	CONFIG_SYS_RESET_ADDRESS	0xFEFFFFFF

/*-----------------------------------------------------------------------
 * Start addresses for the final memory configuration
 * (Set up by the startup code)
 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 */
#define	CONFIG_SYS_SDRAM_BASE		0x00000000
#define CONFIG_SYS_FLASH_BASE		0x40000000
#if defined(DEBUG)
#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
#else
#define	CONFIG_SYS_MONITOR_LEN		(192 << 10)	/* Reserve 192 kB for Monitor	*/
#endif
#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/

/*-----------------------------------------------------------------------
 * FLASH organization
 */
#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max number of memory banks		*/
#define CONFIG_SYS_MAX_FLASH_SECT	67	/* max number of sectors on one chip	*/

#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/

#if 1
/* Start port with environment in flash; switch to SPI EEPROM later */
#define	CONFIG_ENV_IS_IN_FLASH	1
#define	CONFIG_ENV_OFFSET		0x8000	/*   Offset   of Environment Sector	*/
#define	CONFIG_ENV_SIZE		0x4000	/* Total Size of Environment Sector	*/

/* Address and size of Redundant Environment Sector	*/
#define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE)
#define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)
#else
/* Final version: environment in EEPROM */
#define CONFIG_ENV_IS_IN_EEPROM	1
#define CONFIG_ENV_OFFSET		2048
#define CONFIG_ENV_SIZE		2048
#endif

/*-----------------------------------------------------------------------
 * Hardware Information Block
 */
#define CONFIG_SYS_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
#define CONFIG_SYS_HWINFO_SIZE		0x00000040	/* size   of HW Info block */
#define CONFIG_SYS_HWINFO_MAGIC	0x54514D38	/* 'TQM8' */

/*-----------------------------------------------------------------------
 * Cache Configuration
 */
#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/

/*-----------------------------------------------------------------------
 * SYPCR - System Protection Control				11-9
 * SYPCR can only be written once after reset!
 *-----------------------------------------------------------------------
 * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
 */
#if defined(CONFIG_WATCHDOG)
#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
#else
#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
						  SYPCR_SWP)
#endif

/*-----------------------------------------------------------------------
 * SIUMCR - SIU Module Configuration				11-6
 *-----------------------------------------------------------------------
 * we must activate GPL5 in the SIUMCR for CAN
 */
#define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)

/*-----------------------------------------------------------------------
 * TBSCR - Time Base Status and Control				11-26
 *-----------------------------------------------------------------------
 * Clear Reference Interrupt Status, Timebase freezing enabled
 */
#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)

/*-----------------------------------------------------------------------
 * RTCSC - Real-Time Clock Status and Control Register		11-27
 *-----------------------------------------------------------------------
 */
#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)

/*-----------------------------------------------------------------------
 * PISCR - Periodic Interrupt Status and Control		11-31
 *-----------------------------------------------------------------------
 * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
 */
#define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)

/*-----------------------------------------------------------------------
 * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
 *-----------------------------------------------------------------------
 * Reset PLL lock status sticky bit, timer expired status bit and timer
 * interrupt status bit
 *
 * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
 */
#ifdef	CCM_80MHz	/* for 80 MHz, we use a 16 MHz clock * 5 */
#define CONFIG_SYS_PLPRCR							\
		( (5-1)<<PLPRCR_MF_SHIFT | PLPRCR_TEXPS | PLPRCR_TMIST )
#else			/* up to 50 MHz we use a 1:1 clock */
#define CONFIG_SYS_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
#endif	/* CCM_80MHz */

/*-----------------------------------------------------------------------
 * SCCR - System Clock and reset Control Register		15-27
 *-----------------------------------------------------------------------
 * Set clock output, timebase and RTC source and divider,
 * power management and some other internal clocks
 */
#define SCCR_MASK	SCCR_EBDF11
#ifdef	CCM_80MHz	/* for 80 MHz, we use a 16 MHz clock * 5 */
#define CONFIG_SYS_SCCR	(/* SCCR_TBS  | */ \
			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
			 SCCR_DFALCD00)
#else			/* up to 50 MHz we use a 1:1 clock */
#define CONFIG_SYS_SCCR	(SCCR_TBS     | \
			 SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
			 SCCR_DFALCD00)
#endif	/* CCM_80MHz */

/*-----------------------------------------------------------------------
 *
 * Interrupt Levels
 *-----------------------------------------------------------------------
 */
#define CONFIG_SYS_CPM_INTERRUPT	13	/* SIU_LEVEL6	*/

/*-----------------------------------------------------------------------
 *
 *-----------------------------------------------------------------------
 *
 */
#define CONFIG_SYS_DER	0

/*
 * Init Memory Controller:
 *
 * BR0/1 and OR0/1 (FLASH)
 */

#define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
#define FLASH_BASE1_PRELIM	0x60000000	/* FLASH bank #0	*/

/* used to re-map FLASH both when starting from SRAM or FLASH:
 * restrict access enough to keep SRAM working (if any)
 * but not too much to meddle with FLASH accesses
 */
#define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
#define CONFIG_SYS_PRELIM_OR_AM	0xE0000000	/* OR addr mask */

/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1	*/
#define CONFIG_SYS_OR_TIMING_FLASH	(OR_CSNT_SAM  | OR_ACS_DIV2 | OR_BI | \
				 OR_SCY_5_CLK | OR_EHTR)

#define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )

#define CONFIG_SYS_OR1_REMAP	CONFIG_SYS_OR0_REMAP
#define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM
#define CONFIG_SYS_BR1_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )

/*
 * BR2 and OR2 (SDRAM)
 *
 */
#define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
#define SDRAM_BASE3_PRELIM	0x20000000	/* SDRAM bank #1	*/
#define	SDRAM_MAX_SIZE		0x04000000	/* max 64 MB per bank	*/

/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000A00

#define CONFIG_SYS_OR2_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
#define CONFIG_SYS_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )

/*
 * BR3 and OR3 (CAN Controller)
 */
#define	CONFIG_SYS_CAN_BASE		0xC0000000	/* CAN mapped at 0xC0000000	*/
#define CONFIG_SYS_CAN_OR_AM		0xFFFF8000	/* 32 kB address mask		*/
#define CONFIG_SYS_OR3_CAN		(CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
#define CONFIG_SYS_BR3_CAN		((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
					BR_PS_8 | BR_MS_UPMB | BR_V )

/*
 * BR4/OR4: PUMA Config
 *
 * Memory controller will be used in 2 modes:
 *
 * - "read" mode:
 *	BR4: 0x10100801		OR4: 0xffff8520
 * - "load" mode (chip select on UPM B):
 *	BR4: 0x101004c1		OR4: 0xffff8600
 *
 * Default initialization is in "read" mode
 */
#define PUMA_CONF_BASE		0x10100000	/* PUMA Config */
#define PUMA_CONF_OR_AM		0xFFFF8000	/* 32 kB */
#define	PUMA_CONF_LOAD_TIMING	(OR_ACS_DIV2	 | OR_SCY_2_CLK)
#define PUMA_CONF_READ_TIMING	(OR_G5LA | OR_BI | OR_SCY_2_CLK)

#define PUMA_CONF_BR_LOAD	((PUMA_CONF_BASE & BR_BA_MSK) | \
					BR_PS_8  | BR_MS_UPMB | BR_V)
#define PUMA_CONF_OR_LOAD	(PUMA_CONF_OR_AM | PUMA_CONF_LOAD_TIMING)

#define PUMA_CONF_BR_READ	((PUMA_CONF_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
#define PUMA_CONF_OR_READ	(PUMA_CONF_OR_AM | PUMA_CONF_READ_TIMING)

#define CONFIG_SYS_BR4_PRELIM		PUMA_CONF_BR_READ
#define CONFIG_SYS_OR4_PRELIM		PUMA_CONF_OR_READ

/*
 * BR5/OR5: PUMA: SMA Bus 8 Bit
 *	BR5: 0x10200401		OR5: 0xffe0010a
 */
#define PUMA_SMA8_BASE		0x10200000	/* PUMA SMA Bus 8 Bit */
#define PUMA_SMA8_OR_AM		0xFFE00000	/* 2 MB */
#define PUMA_SMA8_TIMING	(OR_BI | OR_SCY_0_CLK | OR_EHTR)

#define CONFIG_SYS_BR5_PRELIM		((PUMA_SMA8_BASE & BR_BA_MSK) | BR_PS_8 | BR_V)
#define CONFIG_SYS_OR5_PRELIM		(PUMA_SMA8_OR_AM | PUMA_SMA8_TIMING | OR_SETA)

/*
 * BR6/OR6: PUMA: SMA Bus 16 Bit
 *	BR6: 0x10600801		OR6: 0xffe0010a
 */
#define PUMA_SMA16_BASE		0x10600000	/* PUMA SMA Bus 16 Bit */
#define PUMA_SMA16_OR_AM	0xFFE00000	/* 2 MB */
#define PUMA_SMA16_TIMING	(OR_BI | OR_SCY_0_CLK | OR_EHTR)

#define CONFIG_SYS_BR6_PRELIM		((PUMA_SMA16_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
#define CONFIG_SYS_OR6_PRELIM		(PUMA_SMA16_OR_AM | PUMA_SMA16_TIMING | OR_SETA)

/*
 * BR7/OR7: PUMA: external Flash
 *	BR7: 0x10a00801		OR7: 0xfe00010a
 */
#define PUMA_FLASH_BASE		0x10A00000	/* PUMA external Flash */
#define PUMA_FLASH_OR_AM	0xFE000000	/* 32 MB */
#define PUMA_FLASH_TIMING	(OR_BI | OR_SCY_0_CLK | OR_EHTR)

#define CONFIG_SYS_BR7_PRELIM		((PUMA_FLASH_BASE & BR_BA_MSK) | BR_PS_16 | BR_V)
#define CONFIG_SYS_OR7_PRELIM		(PUMA_FLASH_OR_AM | PUMA_FLASH_TIMING | OR_SETA)


/*
 * Memory Periodic Timer Prescaler
 */

/* periodic timer for refresh */
#define CONFIG_SYS_MAMR_PTA	97		/* start with divider for 100 MHz	*/

/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit	*/
#define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
#define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/

/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
#define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
#define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/

/*
 * MAMR settings for SDRAM
 */

/* 8 column SDRAM */
#define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
/* 9 column SDRAM */
#define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)


/*
 * Internal Definitions
 *
 * Boot Flags
 */
#define	BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
#define BOOTFLAG_WARM	0x02		/* Software reboot			*/

#endif	/* __CONFIG_H */
Commit	Line	Data
c609719b	1	/*
414eec35	2	* (C) Copyright 2001-2005
c609719b WD	3	* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
	4	*
	5	* See file CREDITS for list of people who contributed to this
	6	* project.
	7	*
	8	* This program is free software; you can redistribute it and/or
	9	* modify it under the terms of the GNU General Public License as
	10	* published by the Free Software Foundation; either version 2 of
	11	* the License, or (at your option) any later version.
	12	*
	13	* This program is distributed in the hope that it will be useful,
	14	* but WITHOUT ANY WARRANTY; without even the implied warranty of
	15	* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
	16	* GNU General Public License for more details.
	17	*
	18	* You should have received a copy of the GNU General Public License
	19	* along with this program; if not, write to the Free Software
	20	* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
	21	* MA 02111-1307 USA
	22	*/
	23
	24	/*
	25	* configuration options, board specific, for Siemens Card Controller Module
	26	*/
	27
	28	#ifndef __CONFIG_H
	29	#define __CONFIG_H
	30
	31	#undef CCM_80MHz /* define for 80 MHz CPU only */
	32
	33	/*
	34	* High Level Configuration Options
	35	* (easy to change)
	36	*/
	37
	38	#define CONFIG_MPC860 1 /* This is a MPC860 CPU ... */
	39	#define CONFIG_CCM 1 /* on a Card Controller Module */
	40
	41	#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
	42	#undef CONFIG_8xx_CONS_SMC2
	43	#undef CONFIG_8xx_CONS_NONE
	44
	45	/* ENVIRONMENT */
	46
	47	#define CONFIG_BAUDRATE 19200 /* console baudrate in bps */
	48	#define CONFIG_BOOTDELAY 2 /* autoboot after 2 seconds */
c609719b WD	49
	50	#define CONFIG_IPADDR 192.168.0.42
	51	#define CONFIG_NETMASK 255.255.255.0
	52	#define CONFIG_GATEWAYIP 0.0.0.0
	53	#define CONFIG_SERVERIP 192.168.0.254
	54
	55	#define CONFIG_HOSTNAME CCM
	56
	57	#define CONFIG_LOADADDR 40180000
	58
	59	#undef CONFIG_BOOTARGS
	60
	61	#define CONFIG_BOOTCOMMAND "setenv bootargs " \
fe126d8b WD	62	"mem=${mem} " \
fe126d8b WD	63	"root=/dev/ram rw ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off " \
8bde7f77 WD	64	"wt_8xx=timeout:3600; " \
8bde7f77 WD	65	"bootm"
c609719b WD	66
c609719b WD	67	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
6d0f6bcf	68	#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
c609719b WD	69
	70	#define CONFIG_WATCHDOG 1 /* watchdog enabled */
	71
	72	#undef CONFIG_STATUS_LED /* Status LED disabled */
	73
	74	#define CONFIG_PRAM 512 /* reserve 512kB "protected RAM"*/
	75
	76	#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
	77
	78	#define CONFIG_SPI /* enable SPI driver */
	79	#define CONFIG_SPI_X /* 16 bit EEPROM addressing */
	80
	81	/* ----------------------------------------------------------------
	82	* Offset to initial SPI buffers in DPRAM (used if the environment
	83	* is in the SPI EEPROM): We need a 520 byte scratch DPRAM area to
	84	* use at an early stage. It is used between the two initialization
	85	* calls (spi_init_f() and spi_init_r()). The value 0xB00 makes it
	86	* far enough from the start of the data area (as well as from the
	87	* stack pointer).
	88	* ---------------------------------------------------------------- */
6d0f6bcf	89	#define CONFIG_SYS_SPI_INIT_OFFSET 0xB00
c609719b	90
6d0f6bcf	91	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* 32-byte page size */
c609719b WD	92
	93
	94	#define CONFIG_MAC_PARTITION /* nod used yet */
	95	#define CONFIG_DOS_PARTITION
	96
5d2ebe1b JL	97	/*
	98	* BOOTP options
	99	*/
	100	#define CONFIG_BOOTP_SUBNETMASK
	101	#define CONFIG_BOOTP_GATEWAY
	102	#define CONFIG_BOOTP_HOSTNAME
	103	#define CONFIG_BOOTP_BOOTPATH
	104	#define CONFIG_BOOTP_BOOTFILESIZE
c609719b	105
c609719b	106
49cf7e8e JL	107	/*
	108	* Command line configuration.
	109	*/
	110	#include <config_cmd_default.h>
	111
	112	#define CONFIG_CMD_BSP
	113	#define CONFIG_CMD_DHCP
	114	#define CONFIG_CMD_DATE
	115	#define CONFIG_CMD_EEPROM
	116	#define CONFIG_CMD_NFS
	117	#define CONFIG_CMD_SNTP
c609719b	118
c609719b WD	119
	120	/*
	121	* Miscellaneous configurable options
	122	*/
6d0f6bcf JCPV	123	#define CONFIG_SYS_LONGHELP /* undef to save memory */
6d0f6bcf JCPV	124	#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
49cf7e8e	125	#if defined(CONFIG_CMD_KGDB)
6d0f6bcf	126	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
c609719b	127	#else
6d0f6bcf	128	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
c609719b	129	#endif
6d0f6bcf JCPV	130	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	131	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	132	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
c609719b	133
6d0f6bcf JCPV	134	#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
6d0f6bcf JCPV	135	#define CONFIG_SYS_MEMTEST_END 0x00F00000 /* 1 ... 15MB in DRAM */
c609719b	136
6d0f6bcf	137	#define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */
c609719b WD	138
c609719b WD	139	/* Ethernet hardware configuration done using port pins */
6d0f6bcf JCPV	140	#define CONFIG_SYS_PA_ETH_RESET 0x0200 /* PA 6 */
	141	#define CONFIG_SYS_PA_ETH_MDDIS 0x4000 /* PA 1 */
	142	#define CONFIG_SYS_PB_ETH_POWERDOWN 0x00000800 /* PB 20 */
	143	#define CONFIG_SYS_PB_ETH_CFG1 0x00000400 /* PB 21 */
	144	#define CONFIG_SYS_PB_ETH_CFG2 0x00000200 /* PB 22 */
	145	#define CONFIG_SYS_PB_ETH_CFG3 0x00000100 /* PB 23 */
c609719b WD	146
	147	/* Ethernet settings:
	148	* MDIO not disabled, autonegotiation, 10/100Mbps, half/full duplex
	149	*/
6d0f6bcf JCPV	150	#define CONFIG_SYS_ETH_MDDIS_VALUE 0
	151	#define CONFIG_SYS_ETH_CFG1_VALUE 1
	152	#define CONFIG_SYS_ETH_CFG2_VALUE 1
	153	#define CONFIG_SYS_ETH_CFG3_VALUE 1
c609719b WD	154
c609719b WD	155	/* PUMA configuration */
6d0f6bcf JCPV	156	#define CONFIG_SYS_PC_PUMA_PROG 0x0200 /* PC 6 */
	157	#define CONFIG_SYS_PC_PUMA_DONE 0x0008 /* PC 12 */
	158	#define CONFIG_SYS_PC_PUMA_INIT 0x0004 /* PC 13 */
c609719b	159
6d0f6bcf	160	#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
c609719b	161
6d0f6bcf	162	#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
c609719b WD	163
	164	/*
	165	* Low Level Configuration Settings
	166	* (address mappings, register initial values, etc.)
	167	* You should know what you are doing if you make changes here.
	168	*/
	169	/*-----------------------------------------------------------------------
	170	* Internal Memory Mapped Register
	171	*/
6d0f6bcf	172	#define CONFIG_SYS_IMMR 0xF0000000
c609719b WD	173
	174	/*-----------------------------------------------------------------------
	175	* Definitions for initial stack pointer and data area (in DPRAM)
	176	*/
6d0f6bcf JCPV	177	#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
	178	#define CONFIG_SYS_INIT_RAM_END 0x2F00 /* End of used area in DPRAM */
	179	#define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
	180	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
	181	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
c609719b WD	182
	183	/*-----------------------------------------------------------------------
	184	* Address accessed to reset the board - must not be mapped/assigned
	185	*/
6d0f6bcf	186	#define CONFIG_SYS_RESET_ADDRESS 0xFEFFFFFF
c609719b WD	187
	188	/*-----------------------------------------------------------------------
	189	* Start addresses for the final memory configuration
	190	* (Set up by the startup code)
6d0f6bcf	191	* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
c609719b	192	*/
6d0f6bcf JCPV	193	#define CONFIG_SYS_SDRAM_BASE 0x00000000
6d0f6bcf JCPV	194	#define CONFIG_SYS_FLASH_BASE 0x40000000
c609719b	195	#if defined(DEBUG)
6d0f6bcf	196	#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
c609719b	197	#else
6d0f6bcf	198	#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
c609719b	199	#endif
6d0f6bcf JCPV	200	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
6d0f6bcf JCPV	201	#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
c609719b WD	202
	203	/*
	204	* For booting Linux, the board info and command line data
	205	* have to be in the first 8 MB of memory, since this is
	206	* the maximum mapped by the Linux kernel during initialization.
	207	*/
6d0f6bcf	208	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
c609719b WD	209
	210	/*-----------------------------------------------------------------------
	211	* FLASH organization
	212	*/
6d0f6bcf JCPV	213	#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
6d0f6bcf JCPV	214	#define CONFIG_SYS_MAX_FLASH_SECT 67 /* max number of sectors on one chip */
c609719b	215
6d0f6bcf JCPV	216	#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
6d0f6bcf JCPV	217	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
c609719b WD	218
	219	#if 1
	220	/* Start port with environment in flash; switch to SPI EEPROM later */
5a1aceb0	221	#define CONFIG_ENV_IS_IN_FLASH 1
0e8d1586 JCPV	222	#define CONFIG_ENV_OFFSET 0x8000 /* Offset of Environment Sector */
0e8d1586 JCPV	223	#define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */
6aff3115 WD	224
6aff3115 WD	225	/* Address and size of Redundant Environment Sector */
0e8d1586 JCPV	226	#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SIZE)
0e8d1586 JCPV	227	#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
c609719b WD	228	#else
c609719b WD	229	/* Final version: environment in EEPROM */
bb1f8b4f	230	#define CONFIG_ENV_IS_IN_EEPROM 1
0e8d1586 JCPV	231	#define CONFIG_ENV_OFFSET 2048
0e8d1586 JCPV	232	#define CONFIG_ENV_SIZE 2048
c609719b WD	233	#endif
	234
	235	/*-----------------------------------------------------------------------
	236	* Hardware Information Block
	237	*/
6d0f6bcf JCPV	238	#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
	239	#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */
	240	#define CONFIG_SYS_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */
c609719b WD	241
	242	/*-----------------------------------------------------------------------
	243	* Cache Configuration
	244	*/
6d0f6bcf JCPV	245	#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
6d0f6bcf JCPV	246	#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
c609719b WD	247
	248	/*-----------------------------------------------------------------------
	249	* SYPCR - System Protection Control 11-9
	250	* SYPCR can only be written once after reset!
	251	*-----------------------------------------------------------------------
	252	* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
	253	*/
	254	#if defined(CONFIG_WATCHDOG)
6d0f6bcf	255	#define CONFIG_SYS_SYPCR (SYPCR_SWTC \| SYPCR_BMT \| SYPCR_BME \| SYPCR_SWF \| \
c609719b WD	256	SYPCR_SWE \| SYPCR_SWRI\| SYPCR_SWP)
c609719b WD	257	#else
6d0f6bcf	258	#define CONFIG_SYS_SYPCR (SYPCR_SWTC \| SYPCR_BMT \| SYPCR_BME \| SYPCR_SWF \| \
6aff3115	259	SYPCR_SWP)
c609719b WD	260	#endif
	261
	262	/*-----------------------------------------------------------------------
	263	* SIUMCR - SIU Module Configuration 11-6
	264	*-----------------------------------------------------------------------
	265	* we must activate GPL5 in the SIUMCR for CAN
	266	*/
6d0f6bcf	267	#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 \| SIUMCR_DBPC00 \| SIUMCR_MLRC01)
c609719b WD	268
	269	/*-----------------------------------------------------------------------
	270	* TBSCR - Time Base Status and Control 11-26
	271	*-----------------------------------------------------------------------
	272	* Clear Reference Interrupt Status, Timebase freezing enabled
	273	*/
6d0f6bcf	274	#define CONFIG_SYS_TBSCR (TBSCR_REFA \| TBSCR_REFB \| TBSCR_TBF)
c609719b WD	275
	276	/*-----------------------------------------------------------------------
	277	* RTCSC - Real-Time Clock Status and Control Register 11-27
	278	*-----------------------------------------------------------------------
	279	*/
6d0f6bcf	280	#define CONFIG_SYS_RTCSC (RTCSC_SEC \| RTCSC_ALR \| RTCSC_RTF\| RTCSC_RTE)
c609719b WD	281
	282	/*-----------------------------------------------------------------------
	283	* PISCR - Periodic Interrupt Status and Control 11-31
	284	*-----------------------------------------------------------------------
	285	* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
	286	*/
6d0f6bcf	287	#define CONFIG_SYS_PISCR (PISCR_PS \| PISCR_PITF)
c609719b WD	288
	289	/*-----------------------------------------------------------------------
	290	* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
	291	*-----------------------------------------------------------------------
	292	* Reset PLL lock status sticky bit, timer expired status bit and timer
	293	* interrupt status bit
	294	*
	295	* If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
	296	*/
	297	#ifdef CCM_80MHz /* for 80 MHz, we use a 16 MHz clock * 5 */
6d0f6bcf	298	#define CONFIG_SYS_PLPRCR \
c609719b WD	299	( (5-1)<<PLPRCR_MF_SHIFT \| PLPRCR_TEXPS \| PLPRCR_TMIST )
c609719b WD	300	#else /* up to 50 MHz we use a 1:1 clock */
6d0f6bcf	301	#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS \| PLPRCR_TEXPS \| PLPRCR_TMIST)
c609719b WD	302	#endif /* CCM_80MHz */
	303
	304	/*-----------------------------------------------------------------------
	305	* SCCR - System Clock and reset Control Register 15-27
	306	*-----------------------------------------------------------------------
	307	* Set clock output, timebase and RTC source and divider,
	308	* power management and some other internal clocks
	309	*/
	310	#define SCCR_MASK SCCR_EBDF11
	311	#ifdef CCM_80MHz /* for 80 MHz, we use a 16 MHz clock * 5 */
6d0f6bcf	312	#define CONFIG_SYS_SCCR (/* SCCR_TBS \| */ \
c609719b WD	313	SCCR_COM00 \| SCCR_DFSYNC00 \| SCCR_DFBRG00 \| \
	314	SCCR_DFNL000 \| SCCR_DFNH000 \| SCCR_DFLCD000 \| \
	315	SCCR_DFALCD00)
	316	#else /* up to 50 MHz we use a 1:1 clock */
6d0f6bcf	317	#define CONFIG_SYS_SCCR (SCCR_TBS \| \
c609719b WD	318	SCCR_COM00 \| SCCR_DFSYNC00 \| SCCR_DFBRG00 \| \
	319	SCCR_DFNL000 \| SCCR_DFNH000 \| SCCR_DFLCD000 \| \
	320	SCCR_DFALCD00)
	321	#endif /* CCM_80MHz */
	322
	323	/*-----------------------------------------------------------------------
	324	*
	325	* Interrupt Levels
	326	*-----------------------------------------------------------------------
	327	*/
6d0f6bcf	328	#define CONFIG_SYS_CPM_INTERRUPT 13 /* SIU_LEVEL6 */
c609719b WD	329
	330	/*-----------------------------------------------------------------------
	331	*
	332	*-----------------------------------------------------------------------
	333	*
	334	*/
6d0f6bcf	335	#define CONFIG_SYS_DER 0
c609719b WD	336
	337	/*
	338	* Init Memory Controller:
	339	*
	340	* BR0/1 and OR0/1 (FLASH)
	341	*/
	342
	343	#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
	344	#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */
	345
	346	/* used to re-map FLASH both when starting from SRAM or FLASH:
	347	* restrict access enough to keep SRAM working (if any)
	348	* but not too much to meddle with FLASH accesses
	349	*/
6d0f6bcf JCPV	350	#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
6d0f6bcf JCPV	351	#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
c609719b WD	352
c609719b WD	353	/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */
6d0f6bcf	354	#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM \| OR_ACS_DIV2 \| OR_BI \| \
c609719b WD	355	OR_SCY_5_CLK \| OR_EHTR)
c609719b WD	356
6d0f6bcf JCPV	357	#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM \| CONFIG_SYS_OR_TIMING_FLASH)
	358	#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM \| CONFIG_SYS_OR_TIMING_FLASH)
	359	#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) \| BR_V )
c609719b	360
6d0f6bcf JCPV	361	#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP
	362	#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
	363	#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) \| BR_V )
c609719b WD	364
	365	/*
	366	* BR2 and OR2 (SDRAM)
	367	*
	368	*/
	369	#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
	370	#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */
	371	#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
	372
	373	/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
6d0f6bcf	374	#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00
c609719b	375
6d0f6bcf JCPV	376	#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR_AM \| CONFIG_SYS_OR_TIMING_SDRAM )
6d0f6bcf JCPV	377	#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) \| BR_MS_UPMA \| BR_V )
c609719b WD	378
	379	/*
	380	* BR3 and OR3 (CAN Controller)
	381	*/
6d0f6bcf JCPV	382	#define CONFIG_SYS_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */
	383	#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
	384	#define CONFIG_SYS_OR3_CAN (CONFIG_SYS_CAN_OR_AM \| OR_G5LA \| OR_BI)
	385	#define CONFIG_SYS_BR3_CAN ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) \| \
c609719b WD	386	BR_PS_8 \| BR_MS_UPMB \| BR_V )
	387
	388	/*
	389	* BR4/OR4: PUMA Config
	390	*
	391	* Memory controller will be used in 2 modes:
	392	*
	393	* - "read" mode:
	394	* BR4: 0x10100801 OR4: 0xffff8520
	395	* - "load" mode (chip select on UPM B):
	396	* BR4: 0x101004c1 OR4: 0xffff8600
	397	*
	398	* Default initialization is in "read" mode
	399	*/
	400	#define PUMA_CONF_BASE 0x10100000 /* PUMA Config */
	401	#define PUMA_CONF_OR_AM 0xFFFF8000 /* 32 kB */
	402	#define PUMA_CONF_LOAD_TIMING (OR_ACS_DIV2 \| OR_SCY_2_CLK)
	403	#define PUMA_CONF_READ_TIMING (OR_G5LA \| OR_BI \| OR_SCY_2_CLK)
	404
	405	#define PUMA_CONF_BR_LOAD ((PUMA_CONF_BASE & BR_BA_MSK) \| \
	406	BR_PS_8 \| BR_MS_UPMB \| BR_V)
	407	#define PUMA_CONF_OR_LOAD (PUMA_CONF_OR_AM \| PUMA_CONF_LOAD_TIMING)
	408
	409	#define PUMA_CONF_BR_READ ((PUMA_CONF_BASE & BR_BA_MSK) \| BR_PS_16 \| BR_V)
	410	#define PUMA_CONF_OR_READ (PUMA_CONF_OR_AM \| PUMA_CONF_READ_TIMING)
	411
6d0f6bcf JCPV	412	#define CONFIG_SYS_BR4_PRELIM PUMA_CONF_BR_READ
6d0f6bcf JCPV	413	#define CONFIG_SYS_OR4_PRELIM PUMA_CONF_OR_READ
c609719b WD	414
	415	/*
	416	* BR5/OR5: PUMA: SMA Bus 8 Bit
	417	* BR5: 0x10200401 OR5: 0xffe0010a
	418	*/
	419	#define PUMA_SMA8_BASE 0x10200000 /* PUMA SMA Bus 8 Bit */
	420	#define PUMA_SMA8_OR_AM 0xFFE00000 /* 2 MB */
	421	#define PUMA_SMA8_TIMING (OR_BI \| OR_SCY_0_CLK \| OR_EHTR)
	422
6d0f6bcf JCPV	423	#define CONFIG_SYS_BR5_PRELIM ((PUMA_SMA8_BASE & BR_BA_MSK) \| BR_PS_8 \| BR_V)
6d0f6bcf JCPV	424	#define CONFIG_SYS_OR5_PRELIM (PUMA_SMA8_OR_AM \| PUMA_SMA8_TIMING \| OR_SETA)
c609719b WD	425
	426	/*
	427	* BR6/OR6: PUMA: SMA Bus 16 Bit
	428	* BR6: 0x10600801 OR6: 0xffe0010a
	429	*/
	430	#define PUMA_SMA16_BASE 0x10600000 /* PUMA SMA Bus 16 Bit */
	431	#define PUMA_SMA16_OR_AM 0xFFE00000 /* 2 MB */
	432	#define PUMA_SMA16_TIMING (OR_BI \| OR_SCY_0_CLK \| OR_EHTR)
	433
6d0f6bcf JCPV	434	#define CONFIG_SYS_BR6_PRELIM ((PUMA_SMA16_BASE & BR_BA_MSK) \| BR_PS_16 \| BR_V)
6d0f6bcf JCPV	435	#define CONFIG_SYS_OR6_PRELIM (PUMA_SMA16_OR_AM \| PUMA_SMA16_TIMING \| OR_SETA)
c609719b WD	436
	437	/*
	438	* BR7/OR7: PUMA: external Flash
	439	* BR7: 0x10a00801 OR7: 0xfe00010a
	440	*/
	441	#define PUMA_FLASH_BASE 0x10A00000 /* PUMA external Flash */
	442	#define PUMA_FLASH_OR_AM 0xFE000000 /* 32 MB */
	443	#define PUMA_FLASH_TIMING (OR_BI \| OR_SCY_0_CLK \| OR_EHTR)
	444
6d0f6bcf JCPV	445	#define CONFIG_SYS_BR7_PRELIM ((PUMA_FLASH_BASE & BR_BA_MSK) \| BR_PS_16 \| BR_V)
6d0f6bcf JCPV	446	#define CONFIG_SYS_OR7_PRELIM (PUMA_FLASH_OR_AM \| PUMA_FLASH_TIMING \| OR_SETA)
c609719b WD	447
	448
	449	/*
	450	* Memory Periodic Timer Prescaler
	451	*/
	452
	453	/* periodic timer for refresh */
6d0f6bcf	454	#define CONFIG_SYS_MAMR_PTA 97 /* start with divider for 100 MHz */
c609719b WD	455
c609719b WD	456	/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
6d0f6bcf JCPV	457	#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
6d0f6bcf JCPV	458	#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
c609719b WD	459
c609719b WD	460	/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
6d0f6bcf JCPV	461	#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
6d0f6bcf JCPV	462	#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
c609719b WD	463
	464	/*
	465	* MAMR settings for SDRAM
	466	*/
	467
	468	/* 8 column SDRAM */
6d0f6bcf	469	#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) \| MAMR_PTAE \| \
c609719b WD	470	MAMR_AMA_TYPE_0 \| MAMR_DSA_1_CYCL \| MAMR_G0CLA_A11 \| \
	471	MAMR_RLFA_1X \| MAMR_WLFA_1X \| MAMR_TLFA_4X)
	472	/* 9 column SDRAM */
6d0f6bcf	473	#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) \| MAMR_PTAE \| \
c609719b WD	474	MAMR_AMA_TYPE_1 \| MAMR_DSA_1_CYCL \| MAMR_G0CLA_A10 \| \
	475	MAMR_RLFA_1X \| MAMR_WLFA_1X \| MAMR_TLFA_4X)
	476
	477
	478	/*
	479	* Internal Definitions
	480	*
	481	* Boot Flags
	482	*/
	483	#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
	484	#define BOOTFLAG_WARM 0x02 /* Software reboot */
	485
	486	#endif /* __CONFIG_H */