[people/ms/u-boot.git] / include / configs / RPXsuper.h

#ifndef __CONFIG_H
#define __CONFIG_H


/*****************************************************************************
 *
 * These settings must match the way _your_ board is set up
 *
 *****************************************************************************/
/* for the AY-Revision which does not use the HRCW */
#define CONFIG_SYS_DEFAULT_IMMR	0x00010000

/* What is the oscillator's (UX2) frequency in Hz? */
#define CONFIG_8260_CLKIN  (66 * 1000 * 1000)

/* How is switch S2 set? We really only want the MODCK[1-3] bits, so
 * only the 3 least significant bits are important.
*/
#define CONFIG_SYS_SBC_S2  0x04

/* What should MODCK_H be? It is dependent on the oscillator
 * frequency, MODCK[1-3], and desired CPM and core frequencies.
 * Some example values (all frequencies are in MHz):
 *
 * MODCK_H   MODCK[1-3]  Osc    CPM    Core
 * 0x2       0x2         33     133    133
 * 0x2       0x4         33     133    200
 * 0x5       0x5         66     133    133
 * 0x5       0x7         66     133    200
 */
#define CONFIG_SYS_SBC_MODCK_H 0x06

#define CONFIG_SYS_SBC_BOOT_LOW 1	/* only for HRCW */
#undef CONFIG_SYS_SBC_BOOT_LOW

/* What should the base address of the main FLASH be and how big is
 * it (in MBytes)? This must contain CONFIG_SYS_TEXT_BASE from board/sbc8260/config.mk
 * The main FLASH is whichever is connected to *CS0. U-Boot expects
 * this to be the SIMM.
 */
#define CONFIG_SYS_FLASH0_BASE 0x80000000
#define CONFIG_SYS_FLASH0_SIZE 16

/* What should the base address of the secondary FLASH be and how big
 * is it (in Mbytes)? The secondary FLASH is whichever is connected
 * to *CS6. U-Boot expects this to be the on board FLASH. If you don't
 * want it enabled, don't define these constants.
 */
#define CONFIG_SYS_FLASH1_BASE 0
#define CONFIG_SYS_FLASH1_SIZE 0
#undef CONFIG_SYS_FLASH1_BASE
#undef CONFIG_SYS_FLASH1_SIZE

/* What should be the base address of SDRAM DIMM and how big is
 * it (in Mbytes)?
*/
#define CONFIG_SYS_SDRAM0_BASE 0x00000000
#define CONFIG_SYS_SDRAM0_SIZE 64

/* What should be the base address of SDRAM DIMM and how big is
 * it (in Mbytes)?
*/
#define CONFIG_SYS_SDRAM1_BASE 0x04000000
#define CONFIG_SYS_SDRAM1_SIZE 32

/* What should be the base address of the LEDs and switch S0?
 * If you don't want them enabled, don't define this.
 */
#define CONFIG_SYS_LED_BASE 0x00000000

/*
 * select serial console configuration
 *
 * if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
 * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
 * for SCC).
 *
 * if CONFIG_CONS_NONE is defined, then the serial console routines must
 * defined elsewhere.
 */
#define CONFIG_CONS_ON_SMC          /* define if console on SMC */
#undef  CONFIG_CONS_ON_SCC          /* define if console on SCC */
#undef  CONFIG_CONS_NONE            /* define if console on neither */
#define CONFIG_CONS_INDEX    1      /* which SMC/SCC channel for console */

/*
 * select ethernet configuration
 *
 * if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
 * CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
 * for FCC)
 *
 * if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
 * defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
 */
#undef  CONFIG_ETHER_ON_SCC           /* define if ethernet on SCC    */
#define CONFIG_ETHER_ON_FCC           /* define if ethernet on FCC    */
#undef  CONFIG_ETHER_NONE             /* define if ethernet on neither */
#define CONFIG_ETHER_INDEX      3     /* which SCC/FCC channel for ethernet */

#if ( CONFIG_ETHER_INDEX == 3 )

/*
 * - Rx-CLK is CLK15
 * - Tx-CLK is CLK16
 * - RAM for BD/Buffers is on the 60x Bus (see 28-13)
 * - Enable Half Duplex in FSMR
 */
# define CONFIG_SYS_CMXFCR_MASK	(CMXFCR_FC3|CMXFCR_RF3CS_MSK|CMXFCR_TF3CS_MSK)
# define CONFIG_SYS_CMXFCR_VALUE	(CMXFCR_RF3CS_CLK15|CMXFCR_TF3CS_CLK16)
# define CONFIG_SYS_CPMFCR_RAMTYPE	0
/*#define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE|FCC_PSMR_LPB) */
# define CONFIG_SYS_FCC_PSMR		0

#else /* CONFIG_ETHER_INDEX */
# error "on RPX Super ethernet must be FCC3"
#endif /* CONFIG_ETHER_INDEX */

#define CONFIG_HARD_I2C         1	/* I2C with hardware support	*/
#define CONFIG_SYS_I2C_SPEED		400000	/* I2C speed and slave address	*/
#define CONFIG_SYS_I2C_SLAVE		0x7F


/* Define this to reserve an entire FLASH sector (256 KB) for
 * environment variables. Otherwise, the environment will be
 * put in the same sector as U-Boot, and changing variables
 * will erase U-Boot temporarily
 */
#define CONFIG_ENV_IN_OWN_SECT

/* Define to allow the user to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE

/* What should the console's baud rate be? */
#define CONFIG_BAUDRATE         115200

/* Ethernet MAC address */
#define CONFIG_ETHADDR          08:00:22:50:70:63

#define CONFIG_IPADDR		192.168.1.99
#define CONFIG_SERVERIP         192.168.1.3

/* Set to a positive value to delay for running BOOTCOMMAND */
#define CONFIG_BOOTDELAY        -1

/* undef this to save memory */
#define CONFIG_SYS_LONGHELP

/* Monitor Command Prompt       */
#define CONFIG_SYS_PROMPT              "=> "


/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME


/*
 * Command line configuration.
 */
#include <config_cmd_default.h>

#define CONFIG_CMD_IMMAP
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_I2C
#define CONFIG_CMD_REGINFO

#undef CONFIG_CMD_KGDB


/* Where do the internal registers live? */
#define CONFIG_SYS_IMMR               0xF0000000

/* Where do the on board registers (CS4) live? */
#define CONFIG_SYS_REGS_BASE          0xFA000000

/*****************************************************************************
 *
 * You should not have to modify any of the following settings
 *
 *****************************************************************************/

#define CONFIG_MPC8260          1       /* This is an MPC8260 CPU   */
#define CONFIG_RPXSUPER         1       /* on an Embedded Planet RPX Super Board  */
#define CONFIG_CPM2		1	/* Has a CPM2 */

#define CONFIG_BOARD_EARLY_INIT_F 1	/* Call board_early_init_f	*/
#define CONFIG_RESET_PHY_R	1	/* Call reset_phy()		*/

/*
 * Miscellaneous configurable options
 */
#if defined(CONFIG_CMD_KGDB)
#  define CONFIG_SYS_CBSIZE              1024       /* Console I/O Buffer Size      */
#else
#  define CONFIG_SYS_CBSIZE              256        /* Console I/O Buffer Size      */
#endif

/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE        (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)

#define CONFIG_SYS_MAXARGS       8            /* max number of command args   */

#define CONFIG_SYS_BARGSIZE      CONFIG_SYS_CBSIZE   /* Boot Argument Buffer Size    */

#define CONFIG_SYS_MEMTEST_START 0x04000000   /* memtest works on  */
#define CONFIG_SYS_MEMTEST_END   0x06000000   /* 64-96 MB in SDRAM */

#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */

#define CONFIG_SYS_LOAD_ADDR     0x100000     /* default load address */
#define CONFIG_SYS_HZ            1000         /* decrementer freq: 1 ms ticks */

/* valid baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE      { 9600, 19200, 38400, 57600, 115200 }

/*
 * Low Level Configuration Settings
 * (address mappings, register initial values, etc.)
 * You should know what you are doing if you make changes here.
 */

#define CONFIG_SYS_FLASH_BASE    CONFIG_SYS_FLASH0_BASE
#define CONFIG_SYS_SDRAM_BASE    CONFIG_SYS_SDRAM0_BASE

/*-----------------------------------------------------------------------
 * Hard Reset Configuration Words
 */
#if defined(CONFIG_SYS_SBC_BOOT_LOW)
#  define  CONFIG_SYS_SBC_HRCW_BOOT_FLAGS  (HRCW_CIP | HRCW_BMS)
#else
#  define  CONFIG_SYS_SBC_HRCW_BOOT_FLAGS  (0)
#endif /* defined(CONFIG_SYS_SBC_BOOT_LOW) */

/* get the HRCW ISB field from CONFIG_SYS_IMMR */
#define CONFIG_SYS_SBC_HRCW_IMMR ( ((CONFIG_SYS_IMMR & 0x10000000) >> 10) |\
			    ((CONFIG_SYS_IMMR & 0x01000000) >> 7)  |\
			    ((CONFIG_SYS_IMMR & 0x00100000) >> 4) )

#define CONFIG_SYS_HRCW_MASTER (HRCW_BPS11                           |\
			 HRCW_DPPC11                          |\
			 CONFIG_SYS_SBC_HRCW_IMMR                    |\
			 HRCW_MMR00                           |\
			 HRCW_LBPC11                          |\
			 HRCW_APPC10                          |\
			 HRCW_CS10PC00                        |\
			 (CONFIG_SYS_SBC_MODCK_H & HRCW_MODCK_H1111) |\
			 CONFIG_SYS_SBC_HRCW_BOOT_FLAGS)

/* no slaves */
#define CONFIG_SYS_HRCW_SLAVE1 0
#define CONFIG_SYS_HRCW_SLAVE2 0
#define CONFIG_SYS_HRCW_SLAVE3 0
#define CONFIG_SYS_HRCW_SLAVE4 0
#define CONFIG_SYS_HRCW_SLAVE5 0
#define CONFIG_SYS_HRCW_SLAVE6 0
#define CONFIG_SYS_HRCW_SLAVE7 0

/*-----------------------------------------------------------------------
 * Definitions for initial stack pointer and data area (in DPRAM)
 */
#define CONFIG_SYS_INIT_RAM_ADDR       CONFIG_SYS_IMMR
#define CONFIG_SYS_INIT_RAM_END        0x4000  /* End of used area in DPRAM    */
#define CONFIG_SYS_GBL_DATA_SIZE      128     /* bytes reserved for initial data */
#define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET      CONFIG_SYS_GBL_DATA_OFFSET

/*-----------------------------------------------------------------------
 * Start addresses for the final memory configuration
 * (Set up by the startup code)
 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 * Note also that the logic that sets CONFIG_SYS_RAMBOOT is platform dependent.
 */
#define CONFIG_SYS_MONITOR_BASE        (CONFIG_SYS_FLASH0_BASE + 0x00F00000)

#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#  define CONFIG_SYS_RAMBOOT
#endif

#define CONFIG_SYS_MONITOR_LEN      (256 << 10)     /* Reserve 256 kB for Monitor   */
#define CONFIG_SYS_MALLOC_LEN       (128 << 10)     /* Reserve 128 kB for malloc()  */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define CONFIG_SYS_BOOTMAPSZ        (8 << 20)       /* Initial Memory map for Linux */

/*-----------------------------------------------------------------------
 * FLASH and environment organization
 */
#define CONFIG_SYS_MAX_FLASH_BANKS   1       /* max number of memory banks         */
#define CONFIG_SYS_MAX_FLASH_SECT    71      /* max number of sectors on one chip  */

#define CONFIG_SYS_FLASH_ERASE_TOUT  8000    /* Timeout for Flash Erase (in ms)    */
#define CONFIG_SYS_FLASH_WRITE_TOUT  1       /* Timeout for Flash Write (in ms)    */

#ifndef CONFIG_SYS_RAMBOOT
#  define CONFIG_ENV_IS_IN_FLASH  1

#  ifdef CONFIG_ENV_IN_OWN_SECT
#    define CONFIG_ENV_ADDR       (CONFIG_SYS_MONITOR_BASE + 0x40000)
#    define CONFIG_ENV_SECT_SIZE  0x40000
#  else
#    define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_ENV_SECT_SIZE)
#    define CONFIG_ENV_SIZE       0x1000  /* Total Size of Environment Sector */
#    define CONFIG_ENV_SECT_SIZE  0x10000 /* see README - env sect real size */
#  endif /* CONFIG_ENV_IN_OWN_SECT */
#else
#  define CONFIG_ENV_IS_IN_NVRAM  1
#  define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
#  define CONFIG_ENV_SIZE         0x200
#endif /* CONFIG_SYS_RAMBOOT */

/*-----------------------------------------------------------------------
 * Cache Configuration
 */
#define CONFIG_SYS_CACHELINE_SIZE      32      /* For MPC8260 CPU */

#if defined(CONFIG_CMD_KGDB)
#  define CONFIG_SYS_CACHELINE_SHIFT     5     /* log base 2 of the above value */
#endif

/*-----------------------------------------------------------------------
 * HIDx - Hardware Implementation-dependent Registers                    2-11
 *-----------------------------------------------------------------------
 * HID0 also contains cache control - initially enable both caches and
 * invalidate contents, then the final state leaves only the instruction
 * cache enabled. Note that Power-On and Hard reset invalidate the caches,
 * but Soft reset does not.
 *
 * HID1 has only read-only information - nothing to set.
 */
#define CONFIG_SYS_HID0_INIT   (/*HID0_ICE  |*/\
			 /*HID0_DCE  |*/\
			 HID0_ICFI |\
			 HID0_DCI  |\
			 HID0_IFEM |\
			 HID0_ABE)

#define CONFIG_SYS_HID0_FINAL  (/*HID0_ICE  |*/\
			 HID0_IFEM |\
			 HID0_ABE  |\
			 HID0_EMCP)
#define CONFIG_SYS_HID2        0

/*-----------------------------------------------------------------------
 * RMR - Reset Mode Register
 *-----------------------------------------------------------------------
 */
#define CONFIG_SYS_RMR         0

/*-----------------------------------------------------------------------
 * BCR - Bus Configuration                                       4-25
 *-----------------------------------------------------------------------
 */
#define CONFIG_SYS_BCR         (BCR_EBM   |\
			 BCR_PLDP  |\
			 BCR_EAV   |\
			 BCR_NPQM0)

/*-----------------------------------------------------------------------
 * SIUMCR - SIU Module Configuration                             4-31
 *-----------------------------------------------------------------------
 */

#define CONFIG_SYS_SIUMCR      (SIUMCR_L2CPC01 |\
			 SIUMCR_APPC10  |\
			 SIUMCR_CS10PC01)


/*-----------------------------------------------------------------------
 * SYPCR - System Protection Control                            11-9
 * SYPCR can only be written once after reset!
 *-----------------------------------------------------------------------
 * Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
 */
#define CONFIG_SYS_SYPCR       (SYPCR_SWTC |\
			 SYPCR_BMT  |\
			 SYPCR_PBME |\
			 SYPCR_LBME |\
			 SYPCR_SWRI |\
			 SYPCR_SWP)

/*-----------------------------------------------------------------------
 * TMCNTSC - Time Counter Status and Control                     4-40
 *-----------------------------------------------------------------------
 * Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
 * and enable Time Counter
 */
#define CONFIG_SYS_TMCNTSC     (TMCNTSC_SEC |\
			 TMCNTSC_ALR |\
			 TMCNTSC_TCF |\
			 TMCNTSC_TCE)

/*-----------------------------------------------------------------------
 * PISCR - Periodic Interrupt Status and Control                 4-42
 *-----------------------------------------------------------------------
 * Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
 * Periodic timer
 */
#define CONFIG_SYS_PISCR       (PISCR_PS  |\
			 PISCR_PTF |\
			 PISCR_PTE)

/*-----------------------------------------------------------------------
 * SCCR - System Clock Control                                   9-8
 *-----------------------------------------------------------------------
 */
#define CONFIG_SYS_SCCR        (SCCR_DFBRG01)

/*-----------------------------------------------------------------------
 * RCCR - RISC Controller Configuration                         13-7
 *-----------------------------------------------------------------------
 */
#define CONFIG_SYS_RCCR        0

/*
 * Init Memory Controller:
 *
 * Bank Bus     Machine PortSz  Device
 * ---- ---     ------- ------  ------
 *  0   60x     GPCM    64 bit  FLASH (BGA - 16MB AMD AM29DL323DB90)
 *  1   60x     SDRAM   64 bit  SDRAM (BGA - 64MB Hitachi HM5225325FBP-B60)
 *  2   Local   SDRAM   32 bit  SDRAM (BGA - 32MB Hitachi HM5225325FBP-B60)
 *  3   unused
 *  4   60x     GPCM     8 bit  Board Regs, LEDs, switches
 *  5   unused
 *  6   unused
 *  7   unused
 *  8   PCMCIA
 *  9   unused
 * 10   unused
 * 11   unused
*/

/* Bank 0 - FLASH
 *
 */
#define CONFIG_SYS_BR0_PRELIM  ((CONFIG_SYS_FLASH0_BASE & BRx_BA_MSK) |\
			 BRx_PS_64                      |\
			 BRx_DECC_NONE                  |\
			 BRx_MS_GPCM_P                  |\
			 BRx_V)

#define CONFIG_SYS_OR0_PRELIM  (MEG_TO_AM(CONFIG_SYS_FLASH0_SIZE)     |\
			 ORxG_CSNT                      |\
			 ORxG_ACS_DIV1                  |\
			 ORxG_SCY_6_CLK                 |\
			 ORxG_EHTR)

/* Bank 1 - SDRAM
 *
 */
#define CONFIG_SYS_BR1_PRELIM  ((CONFIG_SYS_SDRAM0_BASE & BRx_BA_MSK) |\
			 BRx_PS_64                      |\
			 BRx_MS_SDRAM_P                 |\
			 BRx_V)

#define CONFIG_SYS_OR1_PRELIM  (MEG_TO_AM(CONFIG_SYS_SDRAM0_SIZE)     |\
			 ORxS_BPD_4                     |\
			 ORxS_ROWST_PBI0_A8             |\
			 ORxS_NUMR_12                   |\
			 ORxS_IBID)

#define CONFIG_SYS_PSDMR       0x014DA412
#define CONFIG_SYS_PSRT	0x79


/* Bank 2 - SDRAM
 *
 */
#define CONFIG_SYS_BR2_PRELIM  ((CONFIG_SYS_SDRAM1_BASE & BRx_BA_MSK) |\
			 BRx_PS_32                      |\
			 BRx_MS_SDRAM_L                 |\
			 BRx_V)

#define CONFIG_SYS_OR2_PRELIM  (MEG_TO_AM(CONFIG_SYS_SDRAM1_SIZE)     |\
			 ORxS_BPD_4                     |\
			 ORxS_ROWST_PBI0_A9             |\
			 ORxS_NUMR_12)

#define CONFIG_SYS_LSDMR       0x0169A512
#define CONFIG_SYS_LSRT	0x79

#define CONFIG_SYS_MPTPR	(0x0800 & MPTPR_PTP_MSK)

/* Bank 4 - On board registers
 *
 */
#define CONFIG_SYS_BR4_PRELIM   ((CONFIG_SYS_REGS_BASE & BRx_BA_MSK)  |\
			   BRx_PS_8                     |\
			   BRx_MS_GPCM_P                |\
			   BRx_V)

#define CONFIG_SYS_OR4_PRELIM    (ORxG_AM_MSK                 |\
			   ORxG_CSNT                   |\
			   ORxG_ACS_DIV1               |\
			   ORxG_SCY_5_CLK              |\
			   ORxG_TRLX)

/*
 * Internal Definitions
 *
 * Boot Flags
 */
#define BOOTFLAG_COLD   0x01    /* Normal Power-On: Boot from FLASH  */
#define BOOTFLAG_WARM   0x02    /* Software reboot                   */

#endif  /* __CONFIG_H */
Commit	Line	Data
5b1d7137 WD	1	#ifndef __CONFIG_H
	2	#define __CONFIG_H
	3
	4
	5	/*****************************************************************************
	6	*
	7	* These settings must match the way _your_ board is set up
	8	*
	9	*****************************************************************************/
	10	/* for the AY-Revision which does not use the HRCW */
6d0f6bcf	11	#define CONFIG_SYS_DEFAULT_IMMR 0x00010000
5b1d7137 WD	12
	13	/* What is the oscillator's (UX2) frequency in Hz? */
	14	#define CONFIG_8260_CLKIN (66 * 1000 * 1000)
	15
	16	/* How is switch S2 set? We really only want the MODCK[1-3] bits, so
	17	* only the 3 least significant bits are important.
	18	*/
6d0f6bcf	19	#define CONFIG_SYS_SBC_S2 0x04
5b1d7137 WD	20
	21	/* What should MODCK_H be? It is dependent on the oscillator
	22	* frequency, MODCK[1-3], and desired CPM and core frequencies.
	23	* Some example values (all frequencies are in MHz):
	24	*
	25	* MODCK_H MODCK[1-3] Osc CPM Core
	26	* 0x2 0x2 33 133 133
	27	* 0x2 0x4 33 133 200
	28	* 0x5 0x5 66 133 133
	29	* 0x5 0x7 66 133 200
	30	*/
6d0f6bcf	31	#define CONFIG_SYS_SBC_MODCK_H 0x06
5b1d7137	32
6d0f6bcf JCPV	33	#define CONFIG_SYS_SBC_BOOT_LOW 1 /* only for HRCW */
6d0f6bcf JCPV	34	#undef CONFIG_SYS_SBC_BOOT_LOW
5b1d7137 WD	35
5b1d7137 WD	36	/* What should the base address of the main FLASH be and how big is
14d0a02a	37	* it (in MBytes)? This must contain CONFIG_SYS_TEXT_BASE from board/sbc8260/config.mk
5b1d7137 WD	38	* The main FLASH is whichever is connected to *CS0. U-Boot expects
	39	* this to be the SIMM.
	40	*/
6d0f6bcf JCPV	41	#define CONFIG_SYS_FLASH0_BASE 0x80000000
6d0f6bcf JCPV	42	#define CONFIG_SYS_FLASH0_SIZE 16
5b1d7137 WD	43
	44	/* What should the base address of the secondary FLASH be and how big
	45	* is it (in Mbytes)? The secondary FLASH is whichever is connected
	46	* to *CS6. U-Boot expects this to be the on board FLASH. If you don't
	47	* want it enabled, don't define these constants.
	48	*/
6d0f6bcf JCPV	49	#define CONFIG_SYS_FLASH1_BASE 0
	50	#define CONFIG_SYS_FLASH1_SIZE 0
	51	#undef CONFIG_SYS_FLASH1_BASE
	52	#undef CONFIG_SYS_FLASH1_SIZE
5b1d7137 WD	53
	54	/* What should be the base address of SDRAM DIMM and how big is
	55	* it (in Mbytes)?
	56	*/
6d0f6bcf JCPV	57	#define CONFIG_SYS_SDRAM0_BASE 0x00000000
6d0f6bcf JCPV	58	#define CONFIG_SYS_SDRAM0_SIZE 64
5b1d7137 WD	59
	60	/* What should be the base address of SDRAM DIMM and how big is
	61	* it (in Mbytes)?
	62	*/
6d0f6bcf JCPV	63	#define CONFIG_SYS_SDRAM1_BASE 0x04000000
6d0f6bcf JCPV	64	#define CONFIG_SYS_SDRAM1_SIZE 32
5b1d7137 WD	65
	66	/* What should be the base address of the LEDs and switch S0?
	67	* If you don't want them enabled, don't define this.
	68	*/
6d0f6bcf	69	#define CONFIG_SYS_LED_BASE 0x00000000
5b1d7137 WD	70
	71	/*
	72	* select serial console configuration
	73	*
	74	* if either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
	75	* CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
	76	* for SCC).
	77	*
	78	* if CONFIG_CONS_NONE is defined, then the serial console routines must
	79	* defined elsewhere.
	80	*/
	81	#define CONFIG_CONS_ON_SMC /* define if console on SMC */
	82	#undef CONFIG_CONS_ON_SCC /* define if console on SCC */
	83	#undef CONFIG_CONS_NONE /* define if console on neither */
	84	#define CONFIG_CONS_INDEX 1 /* which SMC/SCC channel for console */
	85
	86	/*
	87	* select ethernet configuration
	88	*
	89	* if either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected, then
	90	* CONFIG_ETHER_INDEX must be set to the channel number (1-4 for SCC, 1-3
	91	* for FCC)
	92	*
	93	* if CONFIG_ETHER_NONE is defined, then either the ethernet routines must be
639221c7	94	* defined elsewhere (as for the console), or CONFIG_CMD_NET must be unset.
5b1d7137 WD	95	*/
	96	#undef CONFIG_ETHER_ON_SCC /* define if ethernet on SCC */
	97	#define CONFIG_ETHER_ON_FCC /* define if ethernet on FCC */
	98	#undef CONFIG_ETHER_NONE /* define if ethernet on neither */
	99	#define CONFIG_ETHER_INDEX 3 /* which SCC/FCC channel for ethernet */
	100
	101	#if ( CONFIG_ETHER_INDEX == 3 )
	102
	103	/*
	104	* - Rx-CLK is CLK15
	105	* - Tx-CLK is CLK16
	106	* - RAM for BD/Buffers is on the 60x Bus (see 28-13)
	107	* - Enable Half Duplex in FSMR
	108	*/
6d0f6bcf JCPV	109	# define CONFIG_SYS_CMXFCR_MASK (CMXFCR_FC3\|CMXFCR_RF3CS_MSK\|CMXFCR_TF3CS_MSK)
	110	# define CONFIG_SYS_CMXFCR_VALUE (CMXFCR_RF3CS_CLK15\|CMXFCR_TF3CS_CLK16)
	111	# define CONFIG_SYS_CPMFCR_RAMTYPE 0
	112	/#define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE\|FCC_PSMR_LPB) /
	113	# define CONFIG_SYS_FCC_PSMR 0
5b1d7137 WD	114
	115	#else /* CONFIG_ETHER_INDEX */
	116	# error "on RPX Super ethernet must be FCC3"
	117	#endif /* CONFIG_ETHER_INDEX */
	118
	119	#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
6d0f6bcf JCPV	120	#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
6d0f6bcf JCPV	121	#define CONFIG_SYS_I2C_SLAVE 0x7F
5b1d7137 WD	122
	123
	124	/* Define this to reserve an entire FLASH sector (256 KB) for
	125	* environment variables. Otherwise, the environment will be
	126	* put in the same sector as U-Boot, and changing variables
	127	* will erase U-Boot temporarily
	128	*/
0e8d1586	129	#define CONFIG_ENV_IN_OWN_SECT
5b1d7137 WD	130
	131	/* Define to allow the user to overwrite serial and ethaddr */
	132	#define CONFIG_ENV_OVERWRITE
	133
	134	/* What should the console's baud rate be? */
	135	#define CONFIG_BAUDRATE 115200
	136
	137	/* Ethernet MAC address */
	138	#define CONFIG_ETHADDR 08:00:22:50:70:63
	139
	140	#define CONFIG_IPADDR 192.168.1.99
	141	#define CONFIG_SERVERIP 192.168.1.3
	142
	143	/* Set to a positive value to delay for running BOOTCOMMAND */
	144	#define CONFIG_BOOTDELAY -1
	145
	146	/* undef this to save memory */
6d0f6bcf	147	#define CONFIG_SYS_LONGHELP
5b1d7137 WD	148
5b1d7137 WD	149	/* Monitor Command Prompt */
6d0f6bcf	150	#define CONFIG_SYS_PROMPT "=> "
5b1d7137	151
e9a0f8f1	152
a1aa0bb5 JL	153	/*
	154	* BOOTP options
	155	*/
	156	#define CONFIG_BOOTP_BOOTFILESIZE
	157	#define CONFIG_BOOTP_BOOTPATH
	158	#define CONFIG_BOOTP_GATEWAY
	159	#define CONFIG_BOOTP_HOSTNAME
	160
	161
e9a0f8f1 JL	162	/*
	163	* Command line configuration.
	164	*/
	165	#include <config_cmd_default.h>
	166
	167	#define CONFIG_CMD_IMMAP
	168	#define CONFIG_CMD_ASKENV
	169	#define CONFIG_CMD_I2C
	170	#define CONFIG_CMD_REGINFO
	171
	172	#undef CONFIG_CMD_KGDB
	173
5b1d7137 WD	174
5b1d7137 WD	175	/* Where do the internal registers live? */
6d0f6bcf	176	#define CONFIG_SYS_IMMR 0xF0000000
5b1d7137 WD	177
5b1d7137 WD	178	/* Where do the on board registers (CS4) live? */
6d0f6bcf	179	#define CONFIG_SYS_REGS_BASE 0xFA000000
5b1d7137 WD	180
	181	/*****************************************************************************
	182	*
	183	* You should not have to modify any of the following settings
	184	*
	185	*****************************************************************************/
	186
	187	#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */
	188	#define CONFIG_RPXSUPER 1 /* on an Embedded Planet RPX Super Board */
9c4c5ae3	189	#define CONFIG_CPM2 1 /* Has a CPM2 */
5b1d7137	190
c837dcb1	191	#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
004eca0c	192	#define CONFIG_RESET_PHY_R 1 /* Call reset_phy() */
5b1d7137	193
5b1d7137 WD	194	/*
	195	* Miscellaneous configurable options
	196	*/
e9a0f8f1	197	#if defined(CONFIG_CMD_KGDB)
6d0f6bcf	198	# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
5b1d7137	199	#else
6d0f6bcf	200	# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
5b1d7137 WD	201	#endif
	202
	203	/* Print Buffer Size */
6d0f6bcf	204	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT)+16)
5b1d7137	205
6d0f6bcf	206	#define CONFIG_SYS_MAXARGS 8 /* max number of command args */
5b1d7137	207
6d0f6bcf	208	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
5b1d7137	209
6d0f6bcf JCPV	210	#define CONFIG_SYS_MEMTEST_START 0x04000000 /* memtest works on */
6d0f6bcf JCPV	211	#define CONFIG_SYS_MEMTEST_END 0x06000000 /* 64-96 MB in SDRAM */
5b1d7137 WD	212
	213	#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
	214
6d0f6bcf JCPV	215	#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
6d0f6bcf JCPV	216	#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
5b1d7137 WD	217
5b1d7137 WD	218	/* valid baudrates */
6d0f6bcf	219	#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
5b1d7137 WD	220
	221	/*
	222	* Low Level Configuration Settings
	223	* (address mappings, register initial values, etc.)
	224	* You should know what you are doing if you make changes here.
	225	*/
	226
6d0f6bcf JCPV	227	#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_FLASH0_BASE
6d0f6bcf JCPV	228	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_SDRAM0_BASE
5b1d7137 WD	229
	230	/*-----------------------------------------------------------------------
	231	* Hard Reset Configuration Words
	232	*/
6d0f6bcf JCPV	233	#if defined(CONFIG_SYS_SBC_BOOT_LOW)
6d0f6bcf JCPV	234	# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (HRCW_CIP \| HRCW_BMS)
5b1d7137	235	#else
6d0f6bcf JCPV	236	# define CONFIG_SYS_SBC_HRCW_BOOT_FLAGS (0)
6d0f6bcf JCPV	237	#endif /* defined(CONFIG_SYS_SBC_BOOT_LOW) */
5b1d7137	238
6d0f6bcf JCPV	239	/* get the HRCW ISB field from CONFIG_SYS_IMMR */
	240	#define CONFIG_SYS_SBC_HRCW_IMMR ( ((CONFIG_SYS_IMMR & 0x10000000) >> 10) \|\
	241	((CONFIG_SYS_IMMR & 0x01000000) >> 7) \|\
	242	((CONFIG_SYS_IMMR & 0x00100000) >> 4) )
5b1d7137	243
6d0f6bcf	244	#define CONFIG_SYS_HRCW_MASTER (HRCW_BPS11 \|\
8bde7f77	245	HRCW_DPPC11 \|\
6d0f6bcf	246	CONFIG_SYS_SBC_HRCW_IMMR \|\
8bde7f77 WD	247	HRCW_MMR00 \|\
	248	HRCW_LBPC11 \|\
	249	HRCW_APPC10 \|\
	250	HRCW_CS10PC00 \|\
6d0f6bcf JCPV	251	(CONFIG_SYS_SBC_MODCK_H & HRCW_MODCK_H1111) \|\
6d0f6bcf JCPV	252	CONFIG_SYS_SBC_HRCW_BOOT_FLAGS)
5b1d7137 WD	253
5b1d7137 WD	254	/* no slaves */
6d0f6bcf JCPV	255	#define CONFIG_SYS_HRCW_SLAVE1 0
	256	#define CONFIG_SYS_HRCW_SLAVE2 0
	257	#define CONFIG_SYS_HRCW_SLAVE3 0
	258	#define CONFIG_SYS_HRCW_SLAVE4 0
	259	#define CONFIG_SYS_HRCW_SLAVE5 0
	260	#define CONFIG_SYS_HRCW_SLAVE6 0
	261	#define CONFIG_SYS_HRCW_SLAVE7 0
5b1d7137 WD	262
	263	/*-----------------------------------------------------------------------
	264	* Definitions for initial stack pointer and data area (in DPRAM)
	265	*/
6d0f6bcf JCPV	266	#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
	267	#define CONFIG_SYS_INIT_RAM_END 0x4000 /* End of used area in DPRAM */
	268	#define CONFIG_SYS_GBL_DATA_SIZE 128 /* bytes reserved for initial data */
	269	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
	270	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
5b1d7137 WD	271
	272	/*-----------------------------------------------------------------------
	273	* Start addresses for the final memory configuration
	274	* (Set up by the startup code)
6d0f6bcf JCPV	275	* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
6d0f6bcf JCPV	276	* Note also that the logic that sets CONFIG_SYS_RAMBOOT is platform dependent.
5b1d7137	277	*/
6d0f6bcf	278	#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH0_BASE + 0x00F00000)
5b1d7137	279
6d0f6bcf JCPV	280	#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
6d0f6bcf JCPV	281	# define CONFIG_SYS_RAMBOOT
5b1d7137 WD	282	#endif
5b1d7137 WD	283
6d0f6bcf JCPV	284	#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
6d0f6bcf JCPV	285	#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
5b1d7137 WD	286
	287	/*
	288	* For booting Linux, the board info and command line data
	289	* have to be in the first 8 MB of memory, since this is
	290	* the maximum mapped by the Linux kernel during initialization.
	291	*/
6d0f6bcf	292	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
5b1d7137 WD	293
	294	/*-----------------------------------------------------------------------
	295	* FLASH and environment organization
	296	*/
6d0f6bcf JCPV	297	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
6d0f6bcf JCPV	298	#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
5b1d7137	299
6d0f6bcf JCPV	300	#define CONFIG_SYS_FLASH_ERASE_TOUT 8000 /* Timeout for Flash Erase (in ms) */
6d0f6bcf JCPV	301	#define CONFIG_SYS_FLASH_WRITE_TOUT 1 /* Timeout for Flash Write (in ms) */
5b1d7137	302
6d0f6bcf	303	#ifndef CONFIG_SYS_RAMBOOT
5a1aceb0	304	# define CONFIG_ENV_IS_IN_FLASH 1
5b1d7137	305
0e8d1586	306	# ifdef CONFIG_ENV_IN_OWN_SECT
6d0f6bcf	307	# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000)
0e8d1586	308	# define CONFIG_ENV_SECT_SIZE 0x40000
5b1d7137	309	# else
6d0f6bcf	310	# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_ENV_SECT_SIZE)
0e8d1586 JCPV	311	# define CONFIG_ENV_SIZE 0x1000 /* Total Size of Environment Sector */
	312	# define CONFIG_ENV_SECT_SIZE 0x10000 /* see README - env sect real size */
	313	# endif /* CONFIG_ENV_IN_OWN_SECT */
5b1d7137	314	#else
9314cee6	315	# define CONFIG_ENV_IS_IN_NVRAM 1
6d0f6bcf	316	# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
0e8d1586	317	# define CONFIG_ENV_SIZE 0x200
6d0f6bcf	318	#endif /* CONFIG_SYS_RAMBOOT */
5b1d7137 WD	319
	320	/*-----------------------------------------------------------------------
	321	* Cache Configuration
	322	*/
6d0f6bcf	323	#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
5b1d7137	324
e9a0f8f1	325	#if defined(CONFIG_CMD_KGDB)
6d0f6bcf	326	# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
5b1d7137 WD	327	#endif
	328
	329	/*-----------------------------------------------------------------------
	330	* HIDx - Hardware Implementation-dependent Registers 2-11
	331	*-----------------------------------------------------------------------
	332	* HID0 also contains cache control - initially enable both caches and
	333	* invalidate contents, then the final state leaves only the instruction
	334	* cache enabled. Note that Power-On and Hard reset invalidate the caches,
	335	* but Soft reset does not.
	336	*
	337	* HID1 has only read-only information - nothing to set.
	338	*/
6d0f6bcf	339	#define CONFIG_SYS_HID0_INIT (/HID0_ICE \|/\
5b1d7137 WD	340	/HID0_DCE \|/\
	341	HID0_ICFI \|\
	342	HID0_DCI \|\
	343	HID0_IFEM \|\
	344	HID0_ABE)
	345
6d0f6bcf	346	#define CONFIG_SYS_HID0_FINAL (/HID0_ICE \|/\
5b1d7137 WD	347	HID0_IFEM \|\
	348	HID0_ABE \|\
	349	HID0_EMCP)
6d0f6bcf	350	#define CONFIG_SYS_HID2 0
5b1d7137 WD	351
	352	/*-----------------------------------------------------------------------
	353	* RMR - Reset Mode Register
	354	*-----------------------------------------------------------------------
	355	*/
6d0f6bcf	356	#define CONFIG_SYS_RMR 0
5b1d7137 WD	357
	358	/*-----------------------------------------------------------------------
	359	* BCR - Bus Configuration 4-25
	360	*-----------------------------------------------------------------------
	361	*/
6d0f6bcf	362	#define CONFIG_SYS_BCR (BCR_EBM \|\
5b1d7137 WD	363	BCR_PLDP \|\
	364	BCR_EAV \|\
	365	BCR_NPQM0)
	366
	367	/*-----------------------------------------------------------------------
	368	* SIUMCR - SIU Module Configuration 4-31
	369	*-----------------------------------------------------------------------
	370	*/
	371
6d0f6bcf	372	#define CONFIG_SYS_SIUMCR (SIUMCR_L2CPC01 \|\
8bde7f77 WD	373	SIUMCR_APPC10 \|\
8bde7f77 WD	374	SIUMCR_CS10PC01)
5b1d7137 WD	375
	376
	377	/*-----------------------------------------------------------------------
	378	* SYPCR - System Protection Control 11-9
	379	* SYPCR can only be written once after reset!
	380	*-----------------------------------------------------------------------
	381	* Watchdog & Bus Monitor Timer max, 60x Bus Monitor enable
	382	*/
6d0f6bcf	383	#define CONFIG_SYS_SYPCR (SYPCR_SWTC \|\
8bde7f77 WD	384	SYPCR_BMT \|\
	385	SYPCR_PBME \|\
	386	SYPCR_LBME \|\
	387	SYPCR_SWRI \|\
	388	SYPCR_SWP)
5b1d7137 WD	389
	390	/*-----------------------------------------------------------------------
	391	* TMCNTSC - Time Counter Status and Control 4-40
	392	*-----------------------------------------------------------------------
	393	* Clear once per Second and Alarm Interrupt Status, Set 32KHz timersclk,
	394	* and enable Time Counter
	395	*/
6d0f6bcf	396	#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC \|\
8bde7f77 WD	397	TMCNTSC_ALR \|\
	398	TMCNTSC_TCF \|\
	399	TMCNTSC_TCE)
5b1d7137 WD	400
	401	/*-----------------------------------------------------------------------
	402	* PISCR - Periodic Interrupt Status and Control 4-42
	403	*-----------------------------------------------------------------------
	404	* Clear Periodic Interrupt Status, Set 32KHz timersclk, and enable
	405	* Periodic timer
	406	*/
6d0f6bcf	407	#define CONFIG_SYS_PISCR (PISCR_PS \|\
8bde7f77 WD	408	PISCR_PTF \|\
8bde7f77 WD	409	PISCR_PTE)
5b1d7137 WD	410
	411	/*-----------------------------------------------------------------------
	412	* SCCR - System Clock Control 9-8
	413	*-----------------------------------------------------------------------
	414	*/
6d0f6bcf	415	#define CONFIG_SYS_SCCR (SCCR_DFBRG01)
5b1d7137 WD	416
	417	/*-----------------------------------------------------------------------
	418	* RCCR - RISC Controller Configuration 13-7
	419	*-----------------------------------------------------------------------
	420	*/
6d0f6bcf	421	#define CONFIG_SYS_RCCR 0
5b1d7137 WD	422
	423	/*
	424	* Init Memory Controller:
	425	*
	426	* Bank Bus Machine PortSz Device
	427	* ---- --- ------- ------ ------
	428	* 0 60x GPCM 64 bit FLASH (BGA - 16MB AMD AM29DL323DB90)
	429	* 1 60x SDRAM 64 bit SDRAM (BGA - 64MB Hitachi HM5225325FBP-B60)
	430	* 2 Local SDRAM 32 bit SDRAM (BGA - 32MB Hitachi HM5225325FBP-B60)
	431	* 3 unused
	432	* 4 60x GPCM 8 bit Board Regs, LEDs, switches
	433	* 5 unused
	434	* 6 unused
	435	* 7 unused
	436	* 8 PCMCIA
	437	* 9 unused
	438	* 10 unused
	439	* 11 unused
	440	*/
	441
	442	/* Bank 0 - FLASH
	443	*
	444	*/
6d0f6bcf	445	#define CONFIG_SYS_BR0_PRELIM ((CONFIG_SYS_FLASH0_BASE & BRx_BA_MSK) \|\
8bde7f77	446	BRx_PS_64 \|\
5b1d7137	447	BRx_DECC_NONE \|\
8bde7f77 WD	448	BRx_MS_GPCM_P \|\
8bde7f77 WD	449	BRx_V)
5b1d7137	450
6d0f6bcf	451	#define CONFIG_SYS_OR0_PRELIM (MEG_TO_AM(CONFIG_SYS_FLASH0_SIZE) \|\
8bde7f77 WD	452	ORxG_CSNT \|\
	453	ORxG_ACS_DIV1 \|\
	454	ORxG_SCY_6_CLK \|\
	455	ORxG_EHTR)
5b1d7137 WD	456
	457	/* Bank 1 - SDRAM
	458	*
	459	*/
6d0f6bcf	460	#define CONFIG_SYS_BR1_PRELIM ((CONFIG_SYS_SDRAM0_BASE & BRx_BA_MSK) \|\
8bde7f77 WD	461	BRx_PS_64 \|\
	462	BRx_MS_SDRAM_P \|\
	463	BRx_V)
5b1d7137	464
6d0f6bcf	465	#define CONFIG_SYS_OR1_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM0_SIZE) \|\
8bde7f77 WD	466	ORxS_BPD_4 \|\
	467	ORxS_ROWST_PBI0_A8 \|\
	468	ORxS_NUMR_12 \|\
5b1d7137 WD	469	ORxS_IBID)
5b1d7137 WD	470
6d0f6bcf JCPV	471	#define CONFIG_SYS_PSDMR 0x014DA412
6d0f6bcf JCPV	472	#define CONFIG_SYS_PSRT 0x79
5b1d7137 WD	473
	474
	475	/* Bank 2 - SDRAM
	476	*
	477	*/
6d0f6bcf	478	#define CONFIG_SYS_BR2_PRELIM ((CONFIG_SYS_SDRAM1_BASE & BRx_BA_MSK) \|\
8bde7f77 WD	479	BRx_PS_32 \|\
	480	BRx_MS_SDRAM_L \|\
	481	BRx_V)
5b1d7137	482
6d0f6bcf	483	#define CONFIG_SYS_OR2_PRELIM (MEG_TO_AM(CONFIG_SYS_SDRAM1_SIZE) \|\
8bde7f77 WD	484	ORxS_BPD_4 \|\
	485	ORxS_ROWST_PBI0_A9 \|\
	486	ORxS_NUMR_12)
5b1d7137	487
6d0f6bcf JCPV	488	#define CONFIG_SYS_LSDMR 0x0169A512
6d0f6bcf JCPV	489	#define CONFIG_SYS_LSRT 0x79
5b1d7137	490
6d0f6bcf	491	#define CONFIG_SYS_MPTPR (0x0800 & MPTPR_PTP_MSK)
5b1d7137 WD	492
	493	/* Bank 4 - On board registers
	494	*
	495	*/
6d0f6bcf	496	#define CONFIG_SYS_BR4_PRELIM ((CONFIG_SYS_REGS_BASE & BRx_BA_MSK) \|\
8bde7f77 WD	497	BRx_PS_8 \|\
	498	BRx_MS_GPCM_P \|\
	499	BRx_V)
5b1d7137	500
6d0f6bcf	501	#define CONFIG_SYS_OR4_PRELIM (ORxG_AM_MSK \|\
8bde7f77 WD	502	ORxG_CSNT \|\
	503	ORxG_ACS_DIV1 \|\
	504	ORxG_SCY_5_CLK \|\
	505	ORxG_TRLX)
5b1d7137 WD	506
	507	/*
	508	* Internal Definitions
	509	*
	510	* Boot Flags
	511	*/
	512	#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
	513	#define BOOTFLAG_WARM 0x02 /* Software reboot */
	514
	515	#endif /* __CONFIG_H */