[people/ms/u-boot.git] / include / configs / gr_ep2s60.h

/* Configuration header file for Gaisler Research AB's Template
 * design (GPL Open Source SPARC/LEON3 96MHz) for Altera NIOS
 * Development board Stratix II edition, with the FPGA device
 * EP2S60.
 *
 * (C) Copyright 2003-2005
 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
 *
 * (C) Copyright 2008
 * Daniel Hellstrom, Gaisler Research, daniel@gaisler.com.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_H__
#define __CONFIG_H__

/*
 * High Level Configuration Options
 * (easy to change)
 */

/* Altera NIOS Development board, Stratix II board */
#define CONFIG_GR_EP2S60	1

/* CPU / AMBA BUS configuration */
#define CONFIG_SYS_CLK_FREQ	96000000	/* 96MHz */

/* Define this is the GR-2S60-MEZZ mezzanine is available and you
 * want to use the USB and GRETH functionality of the board
 */
#undef GR_2S60_MEZZ

#ifdef GR_2S60_MEZZ
#define USE_GRETH 1
#define USE_GRUSB 1
#endif

/*
 * Serial console configuration
 */
#define CONFIG_BAUDRATE		38400	/* ... at 38400 bps */
#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }

/* Partitions */
#define CONFIG_ISO_PARTITION

/*
 * Supported commands
 */
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_DIAG
#define CONFIG_CMD_IRQ

/* USB support */
#if USE_GRUSB
#define CONFIG_USB_UHCI
/* Enable needed helper functions */
#endif

/*
 * Autobooting
 */

#define CONFIG_PREBOOT	"echo;"	\
	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
	"echo"

#undef	CONFIG_BOOTARGS

#define	CONFIG_EXTRA_ENV_SETTINGS					\
	"netdev=eth0\0"							\
	"nfsargs=setenv bootargs console=ttyS0,38400 root=/dev/nfs rw "	\
		"nfsroot=${serverip}:${rootpath}\0"			\
	"ramargs=setenv bootargs console=ttyS0,${baudrate} root=/dev/ram rw\0"			\
	"addip=setenv bootargs ${bootargs} "				\
		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
		":${hostname}:${netdev}:off panic=1\0"			\
	"flash_nfs=run nfsargs addip;"					\
		"bootm ${kernel_addr}\0"				\
	"flash_self=run ramargs addip;"					\
		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
	"net_nfs=tftp 40000000 ${bootfile};run nfsargs addip;bootm\0"	\
	"scratch=40800000\0"					\
	"getkernel=tftpboot $(scratch) $(bootfile)\0" \
	"bootargs=console=ttyS0,38400 root=/dev/nfs rw nfsroot=192.168.0.20:/export/rootfs ip=192.168.0.207:192.168.0.20:192.168.0.1:255.255.255.0:ml401:eth0\0" \
	""

#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_GATEWAYIP 192.168.0.1
#define CONFIG_SERVERIP 192.168.0.20
#define CONFIG_IPADDR 192.168.0.207
#define CONFIG_ROOTPATH "/export/rootfs"
#define CONFIG_HOSTNAME  ml401
#define CONFIG_BOOTFILE "/uImage"

#define CONFIG_BOOTCOMMAND	"run flash_self"

/* Memory MAP
 *
 *  Flash:
 *  |--------------------------------|
 *  | 0x00000000 Text & Data & BSS   | *
 *  |            for Monitor         | *
 *  | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~| *
 *  | UNUSED / Growth                | * 256kb
 *  |--------------------------------|
 *  | 0x00050000 Base custom area    | *
 *  |            kernel / FS         | *
 *  |                                | * Rest of Flash
 *  |~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~|
 *  | END-0x00008000 Environment     | * 32kb
 *  |--------------------------------|
 *
 *
 *
 *  Main Memory:
 *  |--------------------------------|
 *  | UNUSED / scratch area          |
 *  |                                |
 *  |                                |
 *  |                                |
 *  |                                |
 *  |--------------------------------|
 *  | Monitor .Text / .DATA / .BSS   | * 512kb
 *  | Relocated!                     | *
 *  |--------------------------------|
 *  | Monitor Malloc                 | * 128kb (contains relocated environment)
 *  |--------------------------------|
 *  | Monitor/kernel STACK           | * 64kb
 *  |--------------------------------|
 *  | Page Table for MMU systems     | * 2k
 *  |--------------------------------|
 *  | PROM Code accessed from Linux  | * 6kb-128b
 *  |--------------------------------|
 *  | Global data (avail from kernel)| * 128b
 *  |--------------------------------|
 *
 */

/*
 * Flash configuration (8,16 or 32 MB)
 * TEXT base always at 0xFFF00000
 * ENV_ADDR always at  0xFFF40000
 * FLASH_BASE at 0xFC000000 for 64 MB
 *               0xFE000000 for 32 MB
 *               0xFF000000 for 16 MB
 *               0xFF800000 for  8 MB
 */
/*#define CONFIG_SYS_NO_FLASH		1*/
#define CONFIG_SYS_FLASH_BASE		0x00000000
#define CONFIG_SYS_FLASH_SIZE		0x00400000	/* FPGA Bit file is in top of FLASH, we only ues the bottom 4Mb */

#define PHYS_FLASH_SECT_SIZE	0x00010000	/* 64 KB sectors */
#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max num of sects on one chip */
#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of memory banks      */

#define CONFIG_SYS_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)  */
#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)  */
#define CONFIG_SYS_FLASH_LOCK_TOUT	5	/* Timeout for Flash Set Lock Bit (in ms) */
#define CONFIG_SYS_FLASH_UNLOCK_TOUT	10000	/* Timeout for Flash Clear Lock Bits (in ms) */
#define CONFIG_SYS_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */

/*** CFI CONFIG ***/
#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_8BIT
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
/* Bypass cache when reading regs from flash memory */
#define CONFIG_SYS_FLASH_CFI_BYPASS_READ
/* Buffered writes (32byte/go) instead of single accesses */
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE

/*
 * Environment settings
 */
/*#define CONFIG_ENV_IS_NOWHERE 1*/
#define CONFIG_ENV_IS_IN_FLASH	1
/* CONFIG_ENV_ADDR need to be at sector boundary */
#define CONFIG_ENV_SIZE		0x8000
#define CONFIG_ENV_SECT_SIZE	0x20000
#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE+CONFIG_SYS_FLASH_SIZE-CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_OVERWRITE	1

/*
 * Memory map
 */
#define CONFIG_SYS_SDRAM_BASE		0x40000000
#define CONFIG_SYS_SDRAM_SIZE		0x02000000
#define CONFIG_SYS_SDRAM_END		(CONFIG_SYS_SDRAM_BASE+CONFIG_SYS_SDRAM_SIZE)

/* no SRAM available */
#undef CONFIG_SYS_SRAM_BASE
#undef CONFIG_SYS_SRAM_SIZE

#define CONFIG_SYS_RAM_BASE CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_RAM_SIZE CONFIG_SYS_SDRAM_SIZE
#define CONFIG_SYS_RAM_END CONFIG_SYS_SDRAM_END

#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_SDRAM_END - GENERATED_GBL_DATA_SIZE)

#define CONFIG_SYS_PROM_SIZE		(8192-GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_PROM_OFFSET		(CONFIG_SYS_GBL_DATA_OFFSET-CONFIG_SYS_PROM_SIZE)

#define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_PROM_OFFSET-32)
#define CONFIG_SYS_STACK_SIZE		(0x10000-32)

#define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#   define CONFIG_SYS_RAMBOOT		1
#endif

#define CONFIG_SYS_MONITOR_LEN		(512 << 10)	/* Reserve 512 kB for Monitor   */
#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()  */
#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */

#define CONFIG_SYS_MALLOC_END		(CONFIG_SYS_INIT_SP_OFFSET-CONFIG_SYS_STACK_SIZE)
#define CONFIG_SYS_MALLOC_BASE		(CONFIG_SYS_MALLOC_END-CONFIG_SYS_MALLOC_LEN)

/* relocated monitor area */
#define CONFIG_SYS_RELOC_MONITOR_MAX_END   CONFIG_SYS_MALLOC_BASE
#define CONFIG_SYS_RELOC_MONITOR_BASE     (CONFIG_SYS_RELOC_MONITOR_MAX_END-CONFIG_SYS_MONITOR_LEN)

/* make un relocated address from relocated address */
#define UN_RELOC(address) (address-(CONFIG_SYS_RELOC_MONITOR_BASE-CONFIG_SYS_TEXT_BASE))

/*
 * Ethernet configuration uses on board SMC91C111, however if a mezzanine
 * with a PHY is attached the GRETH can be used on this board.
 * Define USE_GRETH in order to use the mezzanine provided PHY with the
 * onchip GRETH network MAC, note that this is not supported by the
 * template design.
 */
#ifndef USE_GRETH

/* USE SMC91C111 MAC */
#define CONFIG_SMC91111          1
#define CONFIG_SMC91111_BASE		0x20000300	/* chip select 3         */
#define CONFIG_SMC_USE_32_BIT		1	/* 32 bit bus  */
#undef  CONFIG_SMC_91111_EXT_PHY	/* we use internal phy   */
/*#define CONFIG_SHOW_ACTIVITY*/
#define CONFIG_NET_RETRY_COUNT		10	/* # of retries          */

#else

/* USE GRETH Ethernet Driver */
#define CONFIG_GRETH	1
#endif

#define CONFIG_PHY_ADDR	 0x00

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP		/* undef to save memory     */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
#else
#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
#define CONFIG_SYS_MAXARGS		16	/* max number of command args   */
#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size    */

#define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on */
#define CONFIG_SYS_MEMTEST_END		0x00f00000	/* 1 ... 15 MB in DRAM  */

#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */

/*-----------------------------------------------------------------------
 * USB stuff
 *-----------------------------------------------------------------------
 */
#define CONFIG_USB_CLOCK	0x0001BBBB
#define CONFIG_USB_CONFIG	0x00005000

/***** Gaisler GRLIB IP-Cores Config ********/

#define CONFIG_SYS_GRLIB_SDRAM    0

/* No SDRAM Configuration */
#undef CONFIG_SYS_GRLIB_GAISLER_SDCTRL1

/* See, GRLIB Docs (grip.pdf) on how to set up
 * These the memory controller registers.
 */
#define CONFIG_SYS_GRLIB_ESA_MCTRL1
#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG1  (0x10f800ff | (1<<11))
#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2  0x00000000
#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG3  0x00000000

/* GRLIB FT-MCTRL configuration */
#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1
#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG1  (0x10f800ff | (1<<11))
#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG2  0x00000000
#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG3  0x00000000

/* DDR controller */
#define CONFIG_SYS_GRLIB_GAISLER_DDRSPA1
#define CONFIG_SYS_GRLIB_GAISLER_DDRSPA1_CTRL  0xa900830a

/* no DDR2 Controller */
#undef CONFIG_SYS_GRLIB_GAISLER_DDR2SPA1

/* default kernel command line */
#define CONFIG_DEFAULT_KERNEL_COMMAND_LINE "console=ttyS0,38400\0\0"

#endif				/* __CONFIG_H */
Commit	Line	Data
6940383d DH	1	/* Configuration header file for Gaisler Research AB's Template
	2	* design (GPL Open Source SPARC/LEON3 96MHz) for Altera NIOS
	3	* Development board Stratix II edition, with the FPGA device
	4	* EP2S60.
	5	*
	6	* (C) Copyright 2003-2005
	7	* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
	8	*
	9	* (C) Copyright 2008
	10	* Daniel Hellstrom, Gaisler Research, daniel@gaisler.com.
	11	*
3765b3e7	12	* SPDX-License-Identifier: GPL-2.0+
6940383d DH	13	*/
	14
	15	#ifndef __CONFIG_H__
	16	#define __CONFIG_H__
	17
	18	/*
	19	* High Level Configuration Options
	20	* (easy to change)
	21	*/
	22
6940383d	23	/* Altera NIOS Development board, Stratix II board */
53677ef1	24	#define CONFIG_GR_EP2S60 1
6940383d DH	25
6940383d DH	26	/* CPU / AMBA BUS configuration */
53677ef1	27	#define CONFIG_SYS_CLK_FREQ 96000000 /* 96MHz */
6940383d	28
6940383d DH	29	/* Define this is the GR-2S60-MEZZ mezzanine is available and you
	30	* want to use the USB and GRETH functionality of the board
	31	*/
	32	#undef GR_2S60_MEZZ
	33
	34	#ifdef GR_2S60_MEZZ
	35	#define USE_GRETH 1
	36	#define USE_GRUSB 1
	37	#endif
	38
	39	/*
	40	* Serial console configuration
	41	*/
	42	#define CONFIG_BAUDRATE 38400 /* ... at 38400 bps */
6d0f6bcf	43	#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
6940383d DH	44
6940383d DH	45	/* Partitions */
6940383d DH	46	#define CONFIG_ISO_PARTITION
	47
	48	/*
	49	* Supported commands
	50	*/
6940383d	51	#define CONFIG_CMD_REGINFO
6940383d DH	52	#define CONFIG_CMD_DIAG
	53	#define CONFIG_CMD_IRQ
	54
	55	/* USB support */
	56	#if USE_GRUSB
	57	#define CONFIG_USB_UHCI
6940383d	58	/* Enable needed helper functions */
6940383d DH	59	#endif
	60
	61	/*
	62	* Autobooting
	63	*/
6940383d DH	64
	65	#define CONFIG_PREBOOT "echo;" \
	66	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
	67	"echo"
	68
	69	#undef CONFIG_BOOTARGS
	70
	71	#define CONFIG_EXTRA_ENV_SETTINGS \
	72	"netdev=eth0\0" \
	73	"nfsargs=setenv bootargs console=ttyS0,38400 root=/dev/nfs rw " \
	74	"nfsroot=${serverip}:${rootpath}\0" \
	75	"ramargs=setenv bootargs console=ttyS0,${baudrate} root=/dev/ram rw\0" \
	76	"addip=setenv bootargs ${bootargs} " \
	77	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
	78	":${hostname}:${netdev}:off panic=1\0" \
	79	"flash_nfs=run nfsargs addip;" \
	80	"bootm ${kernel_addr}\0" \
	81	"flash_self=run ramargs addip;" \
	82	"bootm ${kernel_addr} ${ramdisk_addr}\0" \
	83	"net_nfs=tftp 40000000 ${bootfile};run nfsargs addip;bootm\0" \
	84	"scratch=40800000\0" \
3a2b9f28	85	"getkernel=tftpboot $(scratch) $(bootfile)\0" \
6940383d DH	86	"bootargs=console=ttyS0,38400 root=/dev/nfs rw nfsroot=192.168.0.20:/export/rootfs ip=192.168.0.207:192.168.0.20:192.168.0.1:255.255.255.0:ml401:eth0\0" \
	87	""
	88
	89	#define CONFIG_NETMASK 255.255.255.0
	90	#define CONFIG_GATEWAYIP 192.168.0.1
	91	#define CONFIG_SERVERIP 192.168.0.20
	92	#define CONFIG_IPADDR 192.168.0.207
8b3637c6	93	#define CONFIG_ROOTPATH "/export/rootfs"
6940383d	94	#define CONFIG_HOSTNAME ml401
b3f44c21	95	#define CONFIG_BOOTFILE "/uImage"
6940383d DH	96
	97	#define CONFIG_BOOTCOMMAND "run flash_self"
	98
	99	/* Memory MAP
	100	*
	101	* Flash:
	102	* \|--------------------------------\|
	103	* \| 0x00000000 Text & Data & BSS \| *
	104	* \| for Monitor \| *
	105	* \| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~\| *
	106	* \| UNUSED / Growth \| * 256kb
	107	* \|--------------------------------\|
	108	* \| 0x00050000 Base custom area \| *
	109	* \| kernel / FS \| *
	110	* \| \| * Rest of Flash
	111	* \|~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~\|
	112	* \| END-0x00008000 Environment \| * 32kb
	113	* \|--------------------------------\|
	114	*
	115	*
	116	*
	117	* Main Memory:
	118	* \|--------------------------------\|
	119	* \| UNUSED / scratch area \|
	120	* \| \|
	121	* \| \|
	122	* \| \|
	123	* \| \|
	124	* \|--------------------------------\|
	125	* \| Monitor .Text / .DATA / .BSS \| * 512kb
	126	* \| Relocated! \| *
	127	* \|--------------------------------\|
	128	* \| Monitor Malloc \| * 128kb (contains relocated environment)
	129	* \|--------------------------------\|
	130	* \| Monitor/kernel STACK \| * 64kb
	131	* \|--------------------------------\|
	132	* \| Page Table for MMU systems \| * 2k
	133	* \|--------------------------------\|
	134	* \| PROM Code accessed from Linux \| * 6kb-128b
	135	* \|--------------------------------\|
	136	* \| Global data (avail from kernel)\| * 128b
	137	* \|--------------------------------\|
	138	*
	139	*/
	140
	141	/*
	142	* Flash configuration (8,16 or 32 MB)
	143	* TEXT base always at 0xFFF00000
	144	* ENV_ADDR always at 0xFFF40000
	145	* FLASH_BASE at 0xFC000000 for 64 MB
	146	* 0xFE000000 for 32 MB
	147	* 0xFF000000 for 16 MB
	148	* 0xFF800000 for 8 MB
	149	*/
6d0f6bcf JCPV	150	/#define CONFIG_SYS_NO_FLASH 1/
	151	#define CONFIG_SYS_FLASH_BASE 0x00000000
	152	#define CONFIG_SYS_FLASH_SIZE 0x00400000 /* FPGA Bit file is in top of FLASH, we only ues the bottom 4Mb */
6940383d DH	153
6940383d DH	154	#define PHYS_FLASH_SECT_SIZE 0x00010000 /* 64 KB sectors */
6d0f6bcf JCPV	155	#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max num of sects on one chip */
6d0f6bcf JCPV	156	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
6940383d	157
6d0f6bcf JCPV	158	#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
	159	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
	160	#define CONFIG_SYS_FLASH_LOCK_TOUT 5 /* Timeout for Flash Set Lock Bit (in ms) */
	161	#define CONFIG_SYS_FLASH_UNLOCK_TOUT 10000 /* Timeout for Flash Clear Lock Bits (in ms) */
	162	#define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */
6940383d DH	163
6940383d DH	164	/* CFI CONFIG */
6d0f6bcf	165	#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT
00b1883a	166	#define CONFIG_FLASH_CFI_DRIVER
6d0f6bcf	167	#define CONFIG_SYS_FLASH_CFI
6940383d	168	/* Bypass cache when reading regs from flash memory */
6d0f6bcf	169	#define CONFIG_SYS_FLASH_CFI_BYPASS_READ
6940383d	170	/* Buffered writes (32byte/go) instead of single accesses */
6d0f6bcf	171	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
6940383d DH	172
	173	/*
	174	* Environment settings
	175	*/
93f6d725	176	/#define CONFIG_ENV_IS_NOWHERE 1/
5a1aceb0	177	#define CONFIG_ENV_IS_IN_FLASH 1
0e8d1586 JCPV	178	/* CONFIG_ENV_ADDR need to be at sector boundary */
	179	#define CONFIG_ENV_SIZE 0x8000
	180	#define CONFIG_ENV_SECT_SIZE 0x20000
6d0f6bcf	181	#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE+CONFIG_SYS_FLASH_SIZE-CONFIG_ENV_SECT_SIZE)
6940383d DH	182	#define CONFIG_ENV_OVERWRITE 1
	183
	184	/*
	185	* Memory map
	186	*/
6d0f6bcf JCPV	187	#define CONFIG_SYS_SDRAM_BASE 0x40000000
	188	#define CONFIG_SYS_SDRAM_SIZE 0x02000000
	189	#define CONFIG_SYS_SDRAM_END (CONFIG_SYS_SDRAM_BASE+CONFIG_SYS_SDRAM_SIZE)
6940383d DH	190
6940383d DH	191	/* no SRAM available */
6d0f6bcf JCPV	192	#undef CONFIG_SYS_SRAM_BASE
6d0f6bcf JCPV	193	#undef CONFIG_SYS_SRAM_SIZE
6940383d	194
6d0f6bcf JCPV	195	#define CONFIG_SYS_RAM_BASE CONFIG_SYS_SDRAM_BASE
	196	#define CONFIG_SYS_RAM_SIZE CONFIG_SYS_SDRAM_SIZE
	197	#define CONFIG_SYS_RAM_END CONFIG_SYS_SDRAM_END
6940383d	198
25ddd1fb	199	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_SDRAM_END - GENERATED_GBL_DATA_SIZE)
6940383d	200
25ddd1fb	201	#define CONFIG_SYS_PROM_SIZE (8192-GENERATED_GBL_DATA_SIZE)
6d0f6bcf	202	#define CONFIG_SYS_PROM_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET-CONFIG_SYS_PROM_SIZE)
6940383d	203
6d0f6bcf JCPV	204	#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_PROM_OFFSET-32)
6d0f6bcf JCPV	205	#define CONFIG_SYS_STACK_SIZE (0x10000-32)
6940383d	206
14d0a02a	207	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
6d0f6bcf JCPV	208	#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
6d0f6bcf JCPV	209	# define CONFIG_SYS_RAMBOOT 1
6940383d DH	210	#endif
6940383d DH	211
6d0f6bcf JCPV	212	#define CONFIG_SYS_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */
	213	#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
	214	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
6940383d	215
6d0f6bcf JCPV	216	#define CONFIG_SYS_MALLOC_END (CONFIG_SYS_INIT_SP_OFFSET-CONFIG_SYS_STACK_SIZE)
6d0f6bcf JCPV	217	#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MALLOC_END-CONFIG_SYS_MALLOC_LEN)
6940383d DH	218
6940383d DH	219	/* relocated monitor area */
6d0f6bcf JCPV	220	#define CONFIG_SYS_RELOC_MONITOR_MAX_END CONFIG_SYS_MALLOC_BASE
6d0f6bcf JCPV	221	#define CONFIG_SYS_RELOC_MONITOR_BASE (CONFIG_SYS_RELOC_MONITOR_MAX_END-CONFIG_SYS_MONITOR_LEN)
6940383d DH	222
6940383d DH	223	/* make un relocated address from relocated address */
14d0a02a	224	#define UN_RELOC(address) (address-(CONFIG_SYS_RELOC_MONITOR_BASE-CONFIG_SYS_TEXT_BASE))
6940383d DH	225
	226	/*
	227	* Ethernet configuration uses on board SMC91C111, however if a mezzanine
	228	* with a PHY is attached the GRETH can be used on this board.
	229	* Define USE_GRETH in order to use the mezzanine provided PHY with the
	230	* onchip GRETH network MAC, note that this is not supported by the
	231	* template design.
	232	*/
	233	#ifndef USE_GRETH
	234
	235	/* USE SMC91C111 MAC */
7194ab80	236	#define CONFIG_SMC91111 1
6940383d DH	237	#define CONFIG_SMC91111_BASE 0x20000300 /* chip select 3 */
	238	#define CONFIG_SMC_USE_32_BIT 1 /* 32 bit bus */
	239	#undef CONFIG_SMC_91111_EXT_PHY /* we use internal phy */
	240	/#define CONFIG_SHOW_ACTIVITY/
	241	#define CONFIG_NET_RETRY_COUNT 10 /* # of retries */
	242
	243	#else
	244
	245	/* USE GRETH Ethernet Driver */
6940383d	246	#define CONFIG_GRETH 1
1e1f3536	247	#endif
6940383d	248
6940383d DH	249	#define CONFIG_PHY_ADDR 0x00
	250
	251	/*
	252	* Miscellaneous configurable options
	253	*/
6d0f6bcf	254	#define CONFIG_SYS_LONGHELP /* undef to save memory */
6940383d	255	#if defined(CONFIG_CMD_KGDB)
6d0f6bcf	256	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
6940383d	257	#else
6d0f6bcf	258	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
6940383d	259	#endif
6d0f6bcf JCPV	260	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	261	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	262	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
6940383d	263
6d0f6bcf JCPV	264	#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
6d0f6bcf JCPV	265	#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
6940383d	266
6d0f6bcf	267	#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
6940383d	268
6940383d DH	269	/*-----------------------------------------------------------------------
	270	* USB stuff
	271	*-----------------------------------------------------------------------
	272	*/
	273	#define CONFIG_USB_CLOCK 0x0001BBBB
	274	#define CONFIG_USB_CONFIG 0x00005000
	275
	276	/*** Gaisler GRLIB IP-Cores Config ******/
	277
6d0f6bcf	278	#define CONFIG_SYS_GRLIB_SDRAM 0
6940383d	279
cff009ed DH	280	/* No SDRAM Configuration */
	281	#undef CONFIG_SYS_GRLIB_GAISLER_SDCTRL1
	282
6940383d DH	283	/* See, GRLIB Docs (grip.pdf) on how to set up
	284	* These the memory controller registers.
	285	*/
cff009ed DH	286	#define CONFIG_SYS_GRLIB_ESA_MCTRL1
	287	#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG1 (0x10f800ff \| (1<<11))
	288	#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2 0x00000000
	289	#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG3 0x00000000
	290
	291	/* GRLIB FT-MCTRL configuration */
	292	#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1
	293	#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG1 (0x10f800ff \| (1<<11))
	294	#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG2 0x00000000
	295	#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG3 0x00000000
	296
	297	/* DDR controller */
	298	#define CONFIG_SYS_GRLIB_GAISLER_DDRSPA1
	299	#define CONFIG_SYS_GRLIB_GAISLER_DDRSPA1_CTRL 0xa900830a
	300
	301	/* no DDR2 Controller */
	302	#undef CONFIG_SYS_GRLIB_GAISLER_DDR2SPA1
6940383d	303
6940383d DH	304	/* default kernel command line */
	305	#define CONFIG_DEFAULT_KERNEL_COMMAND_LINE "console=ttyS0,38400\0\0"
	306
	307	#endif /* __CONFIG_H */