| | 1 | /* |
| | 2 | * Configuation settings for the Freescale MCF54451 EVB board. |
| | 3 | * |
| | 4 | * Copyright (C) 2004-2008 Freescale Semiconductor, Inc. |
| | 5 | * TsiChung Liew (Tsi-Chung.Liew@freescale.com) |
| | 6 | * |
| | 7 | * SPDX-License-Identifier: GPL-2.0+ |
| | 8 | */ |
| | 9 | |
| | 10 | /* |
| | 11 | * board/config.h - configuration options, board specific |
| | 12 | */ |
| | 13 | |
| | 14 | #ifndef _M54451EVB_H |
| | 15 | #define _M54451EVB_H |
| | 16 | |
| | 17 | /* |
| | 18 | * High Level Configuration Options |
| | 19 | * (easy to change) |
| | 20 | */ |
| | 21 | #define CONFIG_M54451EVB /* M54451EVB board */ |
| | 22 | |
| | 23 | #define CONFIG_MCFUART |
| | 24 | #define CONFIG_SYS_UART_PORT (0) |
| | 25 | |
| | 26 | #define LDS_BOARD_TEXT board/freescale/m54451evb/sbf_dram_init.o (.text*) |
| | 27 | |
| | 28 | #undef CONFIG_WATCHDOG |
| | 29 | |
| | 30 | #define CONFIG_TIMESTAMP /* Print image info with timestamp */ |
| | 31 | |
| | 32 | /* |
| | 33 | * BOOTP options |
| | 34 | */ |
| | 35 | #define CONFIG_BOOTP_BOOTFILESIZE |
| | 36 | #define CONFIG_BOOTP_BOOTPATH |
| | 37 | #define CONFIG_BOOTP_GATEWAY |
| | 38 | #define CONFIG_BOOTP_HOSTNAME |
| | 39 | |
| | 40 | /* Network configuration */ |
| | 41 | #define CONFIG_MCFFEC |
| | 42 | #ifdef CONFIG_MCFFEC |
| | 43 | # define CONFIG_MII 1 |
| | 44 | # define CONFIG_MII_INIT 1 |
| | 45 | # define CONFIG_SYS_DISCOVER_PHY |
| | 46 | # define CONFIG_SYS_RX_ETH_BUFFER 8 |
| | 47 | # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN |
| | 48 | |
| | 49 | # define CONFIG_SYS_FEC0_PINMUX 0 |
| | 50 | # define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE |
| | 51 | # define MCFFEC_TOUT_LOOP 50000 |
| | 52 | |
| | 53 | # define CONFIG_ETHPRIME "FEC0" |
| | 54 | # define CONFIG_IPADDR 192.162.1.2 |
| | 55 | # define CONFIG_NETMASK 255.255.255.0 |
| | 56 | # define CONFIG_SERVERIP 192.162.1.1 |
| | 57 | # define CONFIG_GATEWAYIP 192.162.1.1 |
| | 58 | |
| | 59 | /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ |
| | 60 | # ifndef CONFIG_SYS_DISCOVER_PHY |
| | 61 | # define FECDUPLEX FULL |
| | 62 | # define FECSPEED _100BASET |
| | 63 | # else |
| | 64 | # ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN |
| | 65 | # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN |
| | 66 | # endif |
| | 67 | # endif /* CONFIG_SYS_DISCOVER_PHY */ |
| | 68 | #endif |
| | 69 | |
| | 70 | #define CONFIG_HOSTNAME M54451EVB |
| | 71 | #ifdef CONFIG_SYS_STMICRO_BOOT |
| | 72 | /* ST Micro serial flash */ |
| | 73 | #define CONFIG_SYS_LOAD_ADDR2 0x40010007 |
| | 74 | #define CONFIG_EXTRA_ENV_SETTINGS \ |
| | 75 | "netdev=eth0\0" \ |
| | 76 | "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \ |
| | 77 | "loadaddr=0x40010000\0" \ |
| | 78 | "sbfhdr=sbfhdr.bin\0" \ |
| | 79 | "uboot=u-boot.bin\0" \ |
| | 80 | "load=tftp ${loadaddr} ${sbfhdr};" \ |
| | 81 | "tftp " __stringify(CONFIG_SYS_LOAD_ADDR2) " ${uboot} \0" \ |
| | 82 | "upd=run load; run prog\0" \ |
| | 83 | "prog=sf probe 0:1 1000000 3;" \ |
| | 84 | "sf erase 0 30000;" \ |
| | 85 | "sf write ${loadaddr} 0 30000;" \ |
| | 86 | "save\0" \ |
| | 87 | "" |
| | 88 | #else |
| | 89 | #define CONFIG_SYS_UBOOT_END 0x3FFFF |
| | 90 | #define CONFIG_EXTRA_ENV_SETTINGS \ |
| | 91 | "netdev=eth0\0" \ |
| | 92 | "inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \ |
| | 93 | "loadaddr=40010000\0" \ |
| | 94 | "u-boot=u-boot.bin\0" \ |
| | 95 | "load=tftp ${loadaddr) ${u-boot}\0" \ |
| | 96 | "upd=run load; run prog\0" \ |
| | 97 | "prog=prot off 0 " __stringify(CONFIG_SYS_UBOOT_END) \ |
| | 98 | "; era 0 " __stringify(CONFIG_SYS_UBOOT_END) " ;" \ |
| | 99 | "cp.b ${loadaddr} 0 ${filesize};" \ |
| | 100 | "save\0" \ |
| | 101 | "" |
| | 102 | #endif |
| | 103 | |
| | 104 | /* Realtime clock */ |
| | 105 | #define CONFIG_MCFRTC |
| | 106 | #undef RTC_DEBUG |
| | 107 | #define CONFIG_SYS_RTC_OSCILLATOR (32 * CONFIG_SYS_HZ) |
| | 108 | |
| | 109 | /* Timer */ |
| | 110 | #define CONFIG_MCFTMR |
| | 111 | #undef CONFIG_MCFPIT |
| | 112 | |
| | 113 | /* I2c */ |
| | 114 | #define CONFIG_SYS_I2C |
| | 115 | #define CONFIG_SYS_I2C_FSL |
| | 116 | #define CONFIG_SYS_FSL_I2C_SPEED 80000 |
| | 117 | #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F |
| | 118 | #define CONFIG_SYS_FSL_I2C_OFFSET 0x58000 |
| | 119 | #define CONFIG_SYS_IMMR CONFIG_SYS_MBAR |
| | 120 | |
| | 121 | /* DSPI and Serial Flash */ |
| | 122 | #define CONFIG_CF_SPI |
| | 123 | #define CONFIG_CF_DSPI |
| | 124 | #define CONFIG_SERIAL_FLASH |
| | 125 | #define CONFIG_HARD_SPI |
| | 126 | #define CONFIG_SYS_SBFHDR_SIZE 0x7 |
| | 127 | #ifdef CONFIG_CMD_SPI |
| | 128 | |
| | 129 | # define CONFIG_SYS_DSPI_CTAR0 (DSPI_CTAR_TRSZ(7) | \ |
| | 130 | DSPI_CTAR_PCSSCK_1CLK | \ |
| | 131 | DSPI_CTAR_PASC(0) | \ |
| | 132 | DSPI_CTAR_PDT(0) | \ |
| | 133 | DSPI_CTAR_CSSCK(0) | \ |
| | 134 | DSPI_CTAR_ASC(0) | \ |
| | 135 | DSPI_CTAR_DT(1)) |
| | 136 | # define CONFIG_SYS_DSPI_CTAR1 (CONFIG_SYS_DSPI_CTAR0) |
| | 137 | # define CONFIG_SYS_DSPI_CTAR2 (CONFIG_SYS_DSPI_CTAR0) |
| | 138 | #endif |
| | 139 | |
| | 140 | /* Input, PCI, Flexbus, and VCO */ |
| | 141 | #define CONFIG_EXTRA_CLOCK |
| | 142 | |
| | 143 | #define CONFIG_PRAM 2048 /* 2048 KB */ |
| | 144 | |
| | 145 | #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| | 146 | |
| | 147 | #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| | 148 | #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ |
| | 149 | |
| | 150 | #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x10000) |
| | 151 | |
| | 152 | #define CONFIG_SYS_MBAR 0xFC000000 |
| | 153 | |
| | 154 | /* |
| | 155 | * Low Level Configuration Settings |
| | 156 | * (address mappings, register initial values, etc.) |
| | 157 | * You should know what you are doing if you make changes here. |
| | 158 | */ |
| | 159 | |
| | 160 | /*----------------------------------------------------------------------- |
| | 161 | * Definitions for initial stack pointer and data area (in DPRAM) |
| | 162 | */ |
| | 163 | #define CONFIG_SYS_INIT_RAM_ADDR 0x80000000 |
| | 164 | #define CONFIG_SYS_INIT_RAM_SIZE 0x8000 /* Size of used area in internal SRAM */ |
| | 165 | #define CONFIG_SYS_INIT_RAM_CTRL 0x221 |
| | 166 | #define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 32) |
| | 167 | #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
| | 168 | #define CONFIG_SYS_SBFHDR_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - 32) |
| | 169 | |
| | 170 | /*----------------------------------------------------------------------- |
| | 171 | * Start addresses for the final memory configuration |
| | 172 | * (Set up by the startup code) |
| | 173 | * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 |
| | 174 | */ |
| | 175 | #define CONFIG_SYS_SDRAM_BASE 0x40000000 |
| | 176 | #define CONFIG_SYS_SDRAM_SIZE 128 /* SDRAM size in MB */ |
| | 177 | #define CONFIG_SYS_SDRAM_CFG1 0x33633F30 |
| | 178 | #define CONFIG_SYS_SDRAM_CFG2 0x57670000 |
| | 179 | #define CONFIG_SYS_SDRAM_CTRL 0xE20D2C00 |
| | 180 | #define CONFIG_SYS_SDRAM_EMOD 0x80810000 |
| | 181 | #define CONFIG_SYS_SDRAM_MODE 0x008D0000 |
| | 182 | #define CONFIG_SYS_SDRAM_DRV_STRENGTH 0x44 |
| | 183 | |
| | 184 | #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE + 0x400 |
| | 185 | #define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20) |
| | 186 | |
| | 187 | #ifdef CONFIG_CF_SBF |
| | 188 | # define CONFIG_SERIAL_BOOT |
| | 189 | # define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x400) |
| | 190 | #else |
| | 191 | # define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) |
| | 192 | #endif |
| | 193 | #define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 |
| | 194 | #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */ |
| | 195 | |
| | 196 | /* Reserve 256 kB for malloc() */ |
| | 197 | #define CONFIG_SYS_MALLOC_LEN (256 << 10) |
| | 198 | /* |
| | 199 | * For booting Linux, the board info and command line data |
| | 200 | * have to be in the first 8 MB of memory, since this is |
| | 201 | * the maximum mapped by the Linux kernel during initialization ?? |
| | 202 | */ |
| | 203 | /* Initial Memory map for Linux */ |
| | 204 | #define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20)) |
| | 205 | |
| | 206 | /* Configuration for environment |
| | 207 | * Environment is not embedded in u-boot. First time runing may have env |
| | 208 | * crc error warning if there is no correct environment on the flash. |
| | 209 | */ |
| | 210 | #if defined(CONFIG_SYS_STMICRO_BOOT) |
| | 211 | # define CONFIG_ENV_SPI_CS 1 |
| | 212 | # define CONFIG_ENV_OFFSET 0x20000 |
| | 213 | # define CONFIG_ENV_SIZE 0x2000 |
| | 214 | # define CONFIG_ENV_SECT_SIZE 0x10000 |
| | 215 | #else |
| | 216 | # define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x40000) |
| | 217 | # define CONFIG_ENV_SIZE 0x2000 |
| | 218 | # define CONFIG_ENV_SECT_SIZE 0x20000 |
| | 219 | #endif |
| | 220 | #undef CONFIG_ENV_OVERWRITE |
| | 221 | |
| | 222 | /* FLASH organization */ |
| | 223 | #define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE |
| | 224 | |
| | 225 | #define CONFIG_SYS_FLASH_CFI |
| | 226 | #ifdef CONFIG_SYS_FLASH_CFI |
| | 227 | |
| | 228 | # define CONFIG_FLASH_CFI_DRIVER 1 |
| | 229 | # define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 |
| | 230 | # define CONFIG_SYS_FLASH_SIZE 0x1000000 /* Max size that the board might have */ |
| | 231 | # define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT |
| | 232 | # define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| | 233 | # define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */ |
| | 234 | # define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */ |
| | 235 | # define CONFIG_SYS_FLASH_CHECKSUM |
| | 236 | # define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_CS0_BASE } |
| | 237 | |
| | 238 | #endif |
| | 239 | |
| | 240 | /* |
| | 241 | * This is setting for JFFS2 support in u-boot. |
| | 242 | * NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support. |
| | 243 | */ |
| | 244 | #ifdef CONFIG_CMD_JFFS2 |
| | 245 | # define CONFIG_JFFS2_DEV "nor0" |
| | 246 | # define CONFIG_JFFS2_PART_SIZE 0x01000000 |
| | 247 | # define CONFIG_JFFS2_PART_OFFSET (CONFIG_SYS_FLASH0_BASE + 0x500000) |
| | 248 | #endif |
| | 249 | |
| | 250 | /* Cache Configuration */ |
| | 251 | #define CONFIG_SYS_CACHELINE_SIZE 16 |
| | 252 | |
| | 253 | #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ |
| | 254 | CONFIG_SYS_INIT_RAM_SIZE - 8) |
| | 255 | #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ |
| | 256 | CONFIG_SYS_INIT_RAM_SIZE - 4) |
| | 257 | #define CONFIG_SYS_ICACHE_INV (CF_CACR_BCINVA + CF_CACR_ICINVA) |
| | 258 | #define CONFIG_SYS_DCACHE_INV (CF_CACR_DCINVA) |
| | 259 | #define CONFIG_SYS_CACHE_ACR2 (CONFIG_SYS_SDRAM_BASE | \ |
| | 260 | CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ |
| | 261 | CF_ACR_EN | CF_ACR_SM_ALL) |
| | 262 | #define CONFIG_SYS_CACHE_ICACR (CF_CACR_BEC | CF_CACR_IEC | \ |
| | 263 | CF_CACR_ICINVA | CF_CACR_EUSP) |
| | 264 | #define CONFIG_SYS_CACHE_DCACR ((CONFIG_SYS_CACHE_ICACR | \ |
| | 265 | CF_CACR_DEC | CF_CACR_DDCM_P | \ |
| | 266 | CF_CACR_DCINVA) & ~CF_CACR_ICINVA) |
| | 267 | |
| | 268 | /*----------------------------------------------------------------------- |
| | 269 | * Memory bank definitions |
| | 270 | */ |
| | 271 | /* |
| | 272 | * CS0 - NOR Flash 16MB |
| | 273 | * CS1 - Available |
| | 274 | * CS2 - Available |
| | 275 | * CS3 - Available |
| | 276 | * CS4 - Available |
| | 277 | * CS5 - Available |
| | 278 | */ |
| | 279 | |
| | 280 | /* Flash */ |
| | 281 | #define CONFIG_SYS_CS0_BASE 0x00000000 |
| | 282 | #define CONFIG_SYS_CS0_MASK 0x00FF0001 |
| | 283 | #define CONFIG_SYS_CS0_CTRL 0x00004D80 |
| | 284 | |
| | 285 | #define CONFIG_SYS_SPANSION_BASE CONFIG_SYS_CS0_BASE |
| | 286 | |
| | 287 | #endif /* _M54451EVB_H */ |
projects / people / ms / u-boot.git / blame_incremental