arch/arm/mach-uniphier/Kconfig

   1 if ARCH_UNIPHIER
   2
   3 config SPL_LIBCOMMON_SUPPORT
   4         default y
   5
   6 config SPL_LIBGENERIC_SUPPORT
   7         default y
   8
   9 config SPL_MMC_SUPPORT
  10         default y if !ARCH_UNIPHIER_64BIT
  11
  12 config SPL_NAND_SUPPORT
  13         default y if !ARM64
  14
  15 config SYS_CONFIG_NAME
  16         default "uniphier"
  17
  18 config ARCH_UNIPHIER_32BIT
  19         bool
  20         select CPU_V7
  21         select CPU_V7_HAS_NONSEC
  22         select ARMV7_NONSEC
  23         select ARCH_SUPPORT_PSCI
  24
  25 config ARCH_UNIPHIER_64BIT
  26         bool
  27         select ARM64
  28         select SPL_SEPARATE_BSS
  29         select ARMV8_MULTIENTRY
  30         select ARMV8_SPIN_TABLE
  31
  32 choice
  33         prompt "UniPhier SoC select"
  34         default ARCH_UNIPHIER_PRO4
  35
  36 config ARCH_UNIPHIER_SLD3
  37         bool "UniPhier PH1-sLD3 SoC"
  38         select ARCH_UNIPHIER_32BIT
  39
  40 config ARCH_UNIPHIER_LD4_SLD8
  41         bool "UniPhier PH1-LD4/PH1-sLD8 SoC"
  42         select ARCH_UNIPHIER_32BIT
  43
  44 config ARCH_UNIPHIER_PRO4
  45         bool "UniPhier PH1-Pro4 SoC"
  46         select ARCH_UNIPHIER_32BIT
  47
  48 config ARCH_UNIPHIER_PRO5_PXS2_LD6B
  49         bool "UniPhier PH1-Pro5/ProXstream2/PH1-LD6b SoC"
  50         select ARCH_UNIPHIER_32BIT
  51
  52 config ARCH_UNIPHIER_LD11
  53         bool "UniPhier PH1-LD11 SoC"
  54         select ARCH_UNIPHIER_64BIT
  55
  56 config ARCH_UNIPHIER_LD20
  57         bool "UniPhier PH1-LD20 SoC"
  58         select ARCH_UNIPHIER_64BIT
  59         select OF_BOARD_SETUP
  60
  61 endchoice
  62
  63 config ARCH_UNIPHIER_LD4
  64         bool "Enable UniPhier PH1-LD4 SoC support"
  65         depends on ARCH_UNIPHIER_LD4_SLD8
  66         default y
  67
  68 config ARCH_UNIPHIER_SLD8
  69         bool "Enable UniPhier PH1-sLD8 SoC support"
  70         depends on ARCH_UNIPHIER_LD4_SLD8
  71         default y
  72
  73 config ARCH_UNIPHIER_PRO5
  74         bool "Enable UniPhier PH1-Pro5 SoC support"
  75         depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
  76         default y
  77
  78 config ARCH_UNIPHIER_PXS2
  79         bool "Enable UniPhier ProXstream2 SoC support"
  80         depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
  81         default y
  82
  83 config ARCH_UNIPHIER_LD6B
  84         bool "Enable UniPhier PH1-LD6b SoC support"
  85         depends on ARCH_UNIPHIER_PRO5_PXS2_LD6B
  86         default y
  87
  88 config CACHE_UNIPHIER
  89         bool "Enable the UniPhier L2 cache controller"
  90         depends on ARCH_UNIPHIER_32BIT
  91         select SYS_CACHE_SHIFT_7
  92         default y
  93         help
  94           This option allows to use the UniPhier System Cache as L2 cache.
  95
  96 config MICRO_SUPPORT_CARD
  97         bool "Use Micro Support Card"
  98         help
  99           This option provides support for the expansion board, available
 100           on some UniPhier reference boards.
 101
 102           Say Y to use the on-board UART, Ether, LED devices.
 103
 104 config CMD_PINMON
 105         bool "Enable boot mode pins monitor command"
 106         default y
 107         help
 108           The command "pinmon" shows the state of the boot mode pins.
 109           The boot mode pins are latched when the system reset is deasserted
 110           and determine which device the system should load a boot image from.
 111
 112 config CMD_DDRPHY_DUMP
 113         bool "Enable dump command of DDR PHY parameters"
 114         depends on ARCH_UNIPHIER_LD4 || ARCH_UNIPHIER_PRO4 || ARCH_UNIPHIER_SLD8
 115         default y
 116         help
 117           The command "ddrphy" shows the resulting parameters of DDR PHY
 118           training; it is useful for the evaluation of DDR PHY training.
 119
 120 config CMD_DDRMPHY_DUMP
 121         bool "Enable dump command of DDR Multi PHY parameters"
 122         depends on ARCH_UNIPHIER_PXS2 || ARCH_UNIPHIER_LD6B
 123         default y
 124         help
 125           The command "ddrmphy" shows the resulting parameters of DDR Multi PHY
 126           training; it is useful for the evaluation of DDR Multi PHY training.
 127
 128 endif