drivers/power/Kconfig

   1 menu "Power"
   2
   3 source "drivers/power/domain/Kconfig"
   4
   5 source "drivers/power/pmic/Kconfig"
   6
   7 source "drivers/power/regulator/Kconfig"
   8
   9 choice
  10         prompt "Select Sunxi PMIC Variant"
  11         depends on ARCH_SUNXI
  12         default AXP209_POWER if MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
  13         default AXP221_POWER if MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33
  14         default AXP818_POWER if MACH_SUN8I_A83T
  15         default SUNXI_NO_PMIC if MACH_SUNXI_H3_H5 || MACH_SUN50I
  16
  17 config SUNXI_NO_PMIC
  18         bool "board without a pmic"
  19         ---help---
  20         Select this for boards which do not use a PMIC.
  21
  22 config AXP152_POWER
  23         bool "axp152 pmic support"
  24         depends on MACH_SUN5I
  25         select CMD_POWEROFF
  26         ---help---
  27         Select this to enable support for the axp152 pmic found on most
  28         A10s boards.
  29
  30 config AXP209_POWER
  31         bool "axp209 pmic support"
  32         depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I
  33         select CMD_POWEROFF
  34         ---help---
  35         Select this to enable support for the axp209 pmic found on most
  36         A10, A13 and A20 boards.
  37
  38 config AXP221_POWER
  39         bool "axp221 / axp223 pmic support"
  40         depends on MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33
  41         select CMD_POWEROFF
  42         ---help---
  43         Select this to enable support for the axp221/axp223 pmic found on most
  44         A23 and A31 boards.
  45
  46 config AXP809_POWER
  47         bool "axp809 pmic support"
  48         depends on MACH_SUN9I
  49         select CMD_POWEROFF
  50         ---help---
  51         Say y here to enable support for the axp809 pmic found on A80 boards.
  52
  53 config AXP818_POWER
  54         bool "axp818 pmic support"
  55         depends on MACH_SUN8I_A83T
  56         select CMD_POWEROFF
  57         ---help---
  58         Say y here to enable support for the axp818 pmic found on
  59         A83T dev board.
  60
  61 config SY8106A_POWER
  62         bool "SY8106A pmic support"
  63         depends on MACH_SUNXI_H3_H5
  64         ---help---
  65         Select this to enable support for the SY8106A pmic found on some
  66         H3 boards.
  67
  68 endchoice
  69
  70 config AXP_DCDC1_VOLT
  71         int "axp pmic dcdc1 voltage"
  72         depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
  73         default 3300 if AXP818_POWER
  74         default 3000 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I
  75         ---help---
  76         Set the voltage (mV) to program the axp pmic dcdc1 at, set to 0 to
  77         disable dcdc1. On A23 / A31 / A33 (axp221) boards dcdc1 is used for
  78         generic 3.3V IO voltage for external devices like the lcd-panal and
  79         sdcard interfaces, etc. On most boards dcdc1 is undervolted to 3.0V to
  80         save battery. On A31 devices dcdc1 is also used for VCC-IO. On A83T
  81         dcdc1 is used for VCC-IO, nand, usb0, sd , etc. On A80 dcdc1 normally
  82         powers some of the pingroups, NAND/eMMC, SD/MMC, and USB OTG.
  83
  84 config AXP_DCDC2_VOLT
  85         int "axp pmic dcdc2 voltage"
  86         depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
  87         default 900 if AXP818_POWER
  88         default 1400 if AXP152_POWER || AXP209_POWER
  89         default 1200 if MACH_SUN6I
  90         default 1100 if MACH_SUN8I
  91         default 0 if MACH_SUN9I
  92         ---help---
  93         Set the voltage (mV) to program the axp pmic dcdc2 at, set to 0 to
  94         disable dcdc2.
  95         On A10(s) / A13 / A20 boards dcdc2 is VDD-CPU and should be 1.4V.
  96         On A31 boards dcdc2 is used for VDD-GPU and should be 1.2V.
  97         On A23/A33 boards dcdc2 is used for VDD-SYS and should be 1.1V.
  98         On A80 boards dcdc2 powers the GPU and can be left off.
  99         On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 0.9V.
 100
 101 config AXP_DCDC3_VOLT
 102         int "axp pmic dcdc3 voltage"
 103         depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
 104         default 900 if AXP809_POWER || AXP818_POWER
 105         default 1500 if AXP152_POWER
 106         default 1250 if AXP209_POWER
 107         default 1200 if MACH_SUN6I || MACH_SUN8I
 108         ---help---
 109         Set the voltage (mV) to program the axp pmic dcdc3 at, set to 0 to
 110         disable dcdc3.
 111         On A10(s) / A13 / A20 boards with an axp209 dcdc3 is VDD-INT-DLL and
 112         should be 1.25V.
 113         On A10s boards with an axp152 dcdc3 is VCC-DRAM and should be 1.5V.
 114         On A23 / A31 / A33 boards dcdc3 is VDD-CPU and should be 1.2V.
 115         On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be 0.9V.
 116         On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 0.9V.
 117
 118 config AXP_DCDC4_VOLT
 119         int "axp pmic dcdc4 voltage"
 120         depends on AXP152_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
 121         default 1250 if AXP152_POWER
 122         default 1200 if MACH_SUN6I
 123         default 0 if MACH_SUN8I
 124         default 900 if MACH_SUN9I
 125         ---help---
 126         Set the voltage (mV) to program the axp pmic dcdc4 at, set to 0 to
 127         disable dcdc4.
 128         On A10s boards with an axp152 dcdc4 is VDD-INT-DLL and should be 1.25V.
 129         On A31 boards dcdc4 is used for VDD-SYS and should be 1.2V.
 130         On A23 / A33 boards dcdc4 is unused and should be disabled.
 131         On A80 boards dcdc4 powers VDD-SYS, HDMI, USB OTG and should be 0.9V.
 132         On A83T boards dcdc4 is used for VDD-GPU.
 133
 134 config AXP_DCDC5_VOLT
 135         int "axp pmic dcdc5 voltage"
 136         depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
 137         default 1500 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I
 138         ---help---
 139         Set the voltage (mV) to program the axp pmic dcdc5 at, set to 0 to
 140         disable dcdc5.
 141         On A23 / A31 / A33 / A80 / A83T boards dcdc5 is VCC-DRAM and
 142         should be 1.5V, 1.35V if DDR3L is used.
 143
 144 config AXP_ALDO1_VOLT
 145         int "axp pmic (a)ldo1 voltage"
 146         depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
 147         default 0 if MACH_SUN6I
 148         default 1800 if MACH_SUN8I_A83T
 149         default 3000 if MACH_SUN8I || MACH_SUN9I
 150         ---help---
 151         Set the voltage (mV) to program the axp pmic aldo1 at, set to 0 to
 152         disable aldo1.
 153         On A31 boards aldo1 is often used to power the wifi module.
 154         On A23 / A33 boards aldo1 is used for VCC-IO and should be 3.0V.
 155         On A80 boards aldo1 powers the USB hosts and should be 3.0V.
 156         On A83T / H8 boards aldo1 is used for MIPI CSI, DSI, HDMI, EFUSE, and
 157         should be 1.8V.
 158
 159 config AXP_ALDO2_VOLT
 160         int "axp pmic (a)ldo2 voltage"
 161         depends on AXP152_POWER || AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
 162         default 3000 if AXP152_POWER || AXP209_POWER
 163         default 0 if MACH_SUN6I || MACH_SUN9I
 164         default 1800 if MACH_SUN8I_A83T
 165         default 2500 if MACH_SUN8I
 166         ---help---
 167         Set the voltage (mV) to program the axp pmic aldo2 at, set to 0 to
 168         disable aldo2.
 169         On A10(s) / A13 / A20 boards aldo2 is AVCC and should be 3.0V.
 170         On A31 boards aldo2 is typically unused and should be disabled.
 171         On A31 boards aldo2 may be used for LPDDR2 then it should be 1.8V.
 172         On A23 / A33 boards aldo2 is used for VDD-DLL and should be 2.5V.
 173         On A80 boards aldo2 powers PB pingroup and camera IO and can be left off.
 174         On A83T / H8 boards aldo2 powers VDD-DLL, VCC18-PLL, CPVDD, VDD18-ADC,
 175         LPDDR2, and the codec. It should be 1.8V.
 176
 177 config AXP_ALDO3_VOLT
 178         int "axp pmic (a)ldo3 voltage"
 179         depends on AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER
 180         default 0 if AXP209_POWER || MACH_SUN9I
 181         default 3000 if MACH_SUN6I || MACH_SUN8I
 182         ---help---
 183         Set the voltage (mV) to program the axp pmic aldo3 at, set to 0 to
 184         disable aldo3.
 185         On A10(s) / A13 / A20 boards aldo3 should be 2.8V.
 186         On A23 / A31 / A33 boards aldo3 is VCC-PLL and AVCC and should be 3.0V.
 187         On A80 boards aldo3 is normally not used.
 188         On A83T / H8 boards aldo3 is AVCC, VCC-PL, and VCC-LED, and should be
 189         3.0V.
 190
 191 config AXP_ALDO4_VOLT
 192         int "axp pmic (a)ldo4 voltage"
 193         depends on AXP209_POWER
 194         default 0 if AXP209_POWER
 195         ---help---
 196         Set the voltage (mV) to program the axp pmic aldo4 at, set to 0 to
 197         disable aldo4.
 198         On A10(s) / A13 / A20 boards aldo4 should be 2.8V.
 199
 200 config AXP_DLDO1_VOLT
 201         int "axp pmic dldo1 voltage"
 202         depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
 203         default 0
 204         ---help---
 205         Set the voltage (mV) to program the axp pmic dldo1 at, set to 0 to
 206         disable dldo1. On sun6i (A31) boards with ethernet dldo1 is often used
 207         to power the ethernet phy. On A23, A33 and A80 boards this is often
 208         used to power the wifi.
 209
 210 config AXP_DLDO2_VOLT
 211         int "axp pmic dldo2 voltage"
 212         depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
 213         default 3000 if MACH_SUN9I
 214         default 0
 215         ---help---
 216         Set the voltage (mV) to program the axp pmic dldo2 at, set to 0 to
 217         disable dldo2.
 218         On A80 boards dldo2 normally powers the PL pins and should be 3.0V.
 219
 220 config AXP_DLDO3_VOLT
 221         int "axp pmic dldo3 voltage"
 222         depends on AXP221_POWER || AXP818_POWER
 223         default 0
 224         ---help---
 225         Set the voltage (mV) to program the axp pmic dldo3 at, set to 0 to
 226         disable dldo3.
 227
 228 config AXP_DLDO4_VOLT
 229         int "axp pmic dldo4 voltage"
 230         depends on AXP221_POWER || AXP818_POWER
 231         default 0
 232         ---help---
 233         Set the voltage (mV) to program the axp pmic dldo4 at, set to 0 to
 234         disable dldo4.
 235
 236 config AXP_ELDO1_VOLT
 237         int "axp pmic eldo1 voltage"
 238         depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
 239         default 0
 240         ---help---
 241         Set the voltage (mV) to program the axp pmic eldo1 at, set to 0 to
 242         disable eldo1.
 243
 244 config AXP_ELDO2_VOLT
 245         int "axp pmic eldo2 voltage"
 246         depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
 247         default 0
 248         ---help---
 249         Set the voltage (mV) to program the axp pmic eldo2 at, set to 0 to
 250         disable eldo2.
 251
 252 config AXP_ELDO3_VOLT
 253         int "axp pmic eldo3 voltage"
 254         depends on AXP221_POWER || AXP809_POWER || AXP818_POWER
 255         default 3000 if MACH_SUN9I
 256         default 0
 257         ---help---
 258         Set the voltage (mV) to program the axp pmic eldo3 at, set to 0 to
 259         disable eldo3. On some A31(s) tablets it might be used to supply
 260         1.2V for the SSD2828 chip (converter of parallel LCD interface
 261         into MIPI DSI).
 262         On A80 boards it powers the PM pingroup and should be 3.0V.
 263
 264 config AXP_FLDO1_VOLT
 265         int "axp pmic fldo1 voltage"
 266         depends on AXP818_POWER
 267         default 0 if MACH_SUN8I_A83T
 268         ---help---
 269         Set the voltage (mV) to program the axp pmic fldo1 at, set to 0 to
 270         disable fldo1.
 271         On A83T / H8 boards fldo1 is VCC-HSIC and should be 1.2V if HSIC is
 272         used.
 273
 274 config AXP_FLDO2_VOLT
 275         int "axp pmic fldo2 voltage"
 276         depends on AXP818_POWER
 277         default 900 if MACH_SUN8I_A83T
 278         ---help---
 279         Set the voltage (mV) to program the axp pmic fldo2 at, set to 0 to
 280         disable fldo2.
 281         On A83T / H8 boards fldo2 is VCC-CPUS and should be 0.9V.
 282
 283 config AXP_FLDO3_VOLT
 284         int "axp pmic fldo3 voltage"
 285         depends on AXP818_POWER
 286         default 0
 287         ---help---
 288         Set the voltage (mV) to program the axp pmic fldo3 at, set to 0 to
 289         disable fldo3.
 290
 291 config AXP_SW_ON
 292         bool "axp pmic sw on"
 293         depends on AXP809_POWER || AXP818_POWER
 294         default n
 295         ---help---
 296         Enable to turn on axp pmic sw.
 297
 298 config SY8106A_VOUT1_VOLT
 299         int "SY8106A pmic VOUT1 voltage"
 300         depends on SY8106A_POWER
 301         default 1200
 302         ---help---
 303         Set the voltage (mV) to program the SY8106A pmic VOUT1. This
 304         is typically used to power the VDD-CPU and should be 1200mV.
 305         Values can range from 680mV till 1950mV.
 306
 307 endmenu