include/configs/CMS700.h

   1 /*
   2  * (C) Copyright 2005
   3  * Matthias Fuchs, esd gmbh germany, matthias.fuchs@esd-electronics.com
   4  *
   5  * See file CREDITS for list of people who contributed to this
   6  * project.
   7  *
   8  * This program is free software; you can redistribute it and/or
   9  * modify it under the terms of the GNU General Public License as
  10  * published by the Free Software Foundation; either version 2 of
  11  * the License, or (at your option) any later version.
  12  *
  13  * This program is distributed in the hope that it will be useful,
  14  * but WITHOUT ANY WARRANTY; without even the implied warranty of
  15  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  16  * GNU General Public License for more details.
  17  *
  18  * You should have received a copy of the GNU General Public License
  19  * along with this program; if not, write to the Free Software
  20  * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
  21  * MA 02111-1307 USA
  22  */
  23
  24 /*
  25  * CMS700.h - configuration options, board specific
  26  */
  27
  28 #ifndef __CONFIG_H
  29 #define __CONFIG_H
  30
  31 /*
  32  * High Level Configuration Options
  33  * (easy to change)
  34  */
  35
  36 #define CONFIG_405EP            1       /* This is a PPC405 CPU         */
  37 #define CONFIG_4xx              1       /* ...member of PPC4xx family   */
  38 #define CONFIG_VOM405           1       /* ...on a VOM405 board         */
  39
  40 #define CONFIG_BOARD_EARLY_INIT_F 1     /* call board_early_init_f()    */
  41 #define CONFIG_MISC_INIT_R      1       /* call misc_init_r()           */
  42
  43 #define CONFIG_SYS_CLK_FREQ     33330000 /* external frequency to pll   */
  44
  45 #define CONFIG_BAUDRATE         9600
  46 #define CONFIG_BOOTDELAY        3       /* autoboot after 3 seconds     */
  47
  48 #undef  CONFIG_BOOTARGS
  49 #undef  CONFIG_BOOTCOMMAND
  50
  51 #define CONFIG_PREBOOT                  /* enable preboot variable      */
  52
  53 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change        */
  54
  55 #define CONFIG_NET_MULTI        1
  56 #undef  CONFIG_HAS_ETH1
  57
  58 #define CONFIG_MII              1       /* MII PHY management           */
  59 #define CONFIG_PHY_ADDR         0       /* PHY address                  */
  60 #define CONFIG_LXT971_NO_SLEEP  1       /* disable sleep mode in LXT971 */
  61 #define CONFIG_RESET_PHY_R      1       /* use reset_phy() to disable phy sleep mode */
  62
  63 /*
  64  * BOOTP options
  65  */
  66 #define CONFIG_BOOTP_SUBNETMASK
  67 #define CONFIG_BOOTP_GATEWAY
  68 #define CONFIG_BOOTP_HOSTNAME
  69 #define CONFIG_BOOTP_BOOTPATH
  70 #define CONFIG_BOOTP_DNS
  71 #define CONFIG_BOOTP_DNS2
  72 #define CONFIG_BOOTP_SEND_HOSTNAME
  73
  74
  75 /*
  76  * Command line configuration.
  77  */
  78 #include <config_cmd_default.h>
  79
  80 #define CONFIG_CMD_DHCP
  81 #define CONFIG_CMD_BSP
  82 #define CONFIG_CMD_PCI
  83 #define CONFIG_CMD_IRQ
  84 #define CONFIG_CMD_ELF
  85 #define CONFIG_CMD_NAND
  86 #define CONFIG_CMD_I2C
  87 #define CONFIG_CMD_DATE
  88 #define CONFIG_CMD_MII
  89 #define CONFIG_CMD_PING
  90 #define CONFIG_CMD_EEPROM
  91
  92
  93 #undef  CONFIG_WATCHDOG                 /* watchdog disabled            */
  94
  95 #define CONFIG_SDRAM_BANK0      1       /* init onboard SDRAM bank 0    */
  96
  97 #undef  CONFIG_PRAM                     /* no "protected RAM"           */
  98
  99 /*
 100  * Miscellaneous configurable options
 101  */
 102 #define CONFIG_SYS_LONGHELP                     /* undef to save memory         */
 103 #define CONFIG_SYS_PROMPT       "=> "           /* Monitor Command Prompt       */
 104
 105 #undef  CONFIG_SYS_HUSH_PARSER                  /* use "hush" command parser    */
 106 #ifdef  CONFIG_SYS_HUSH_PARSER
 107 #define CONFIG_SYS_PROMPT_HUSH_PS2      "> "
 108 #endif
 109
 110 #if defined(CONFIG_CMD_KGDB)
 111 #define CONFIG_SYS_CBSIZE       1024            /* Console I/O Buffer Size      */
 112 #else
 113 #define CONFIG_SYS_CBSIZE       256             /* Console I/O Buffer Size      */
 114 #endif
 115 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 116 #define CONFIG_SYS_MAXARGS      16              /* max number of command args   */
 117 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 118
 119 #define CONFIG_SYS_DEVICE_NULLDEV       1       /* include nulldev device       */
 120
 121 #define CONFIG_SYS_CONSOLE_INFO_QUIET   1       /* don't print console @ startup*/
 122
 123 #define CONFIG_SYS_MEMTEST_START        0x0400000       /* memtest works on     */
 124 #define CONFIG_SYS_MEMTEST_END          0x0C00000       /* 4 ... 12 MB in DRAM  */
 125
 126 #undef  CONFIG_SYS_EXT_SERIAL_CLOCK            /* no external serial clock used */
 127 #define CONFIG_SYS_IGNORE_405_UART_ERRATA_59    /* ignore ppc405gp errata #59   */
 128 #define CONFIG_SYS_BASE_BAUD        691200
 129 #define CONFIG_UART1_CONSOLE            /* define for uart1 as console  */
 130
 131 /* The following table includes the supported baudrates */
 132 #define CONFIG_SYS_BAUDRATE_TABLE       \
 133         { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400,     \
 134          57600, 115200, 230400, 460800, 921600 }
 135
 136 #define CONFIG_SYS_LOAD_ADDR    0x100000        /* default load address */
 137 #define CONFIG_SYS_EXTBDINFO    1               /* To use extended board_into (bd_t) */
 138
 139 #define CONFIG_SYS_HZ           1000            /* decrementer freq: 1 ms ticks */
 140
 141 #define CONFIG_ZERO_BOOTDELAY_CHECK     /* check for keypress on bootdelay==0 */
 142
 143 #define CONFIG_VERSION_VARIABLE 1       /* include version env variable */
 144
 145 #define CONFIG_SYS_RX_ETH_BUFFER        16      /* use 16 rx buffer on 405 emac */
 146
 147 /*-----------------------------------------------------------------------
 148  * RTC stuff
 149  *-----------------------------------------------------------------------
 150  */
 151 #define CONFIG_RTC_DS1337
 152 #define CONFIG_SYS_I2C_RTC_ADDR 0x68
 153
 154 /*-----------------------------------------------------------------------
 155  * NAND-FLASH stuff
 156  *-----------------------------------------------------------------------
 157  */
 158 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 159 #define NAND_MAX_CHIPS          1
 160 #define CONFIG_SYS_MAX_NAND_DEVICE      1         /* Max number of NAND devices */
 161 #define NAND_BIG_DELAY_US       25
 162
 163 #define CONFIG_SYS_NAND_CE             (0x80000000 >> 1)   /* our CE is GPIO1  */
 164 #define CONFIG_SYS_NAND_RDY            (0x80000000 >> 4)   /* our RDY is GPIO4 */
 165 #define CONFIG_SYS_NAND_CLE            (0x80000000 >> 2)   /* our CLE is GPIO2 */
 166 #define CONFIG_SYS_NAND_ALE            (0x80000000 >> 3)   /* our ALE is GPIO3 */
 167
 168 #define CONFIG_SYS_NAND_SKIP_BAD_DOT_I 1       /* ".i" read skips bad blocks   */
 169 #define CONFIG_SYS_NAND_QUIET          1
 170
 171 /*-----------------------------------------------------------------------
 172  * PCI stuff
 173  *-----------------------------------------------------------------------
 174  */
 175 #define PCI_HOST_ADAPTER 0              /* configure as pci adapter     */
 176 #define PCI_HOST_FORCE  1               /* configure as pci host        */
 177 #define PCI_HOST_AUTO   2               /* detected via arbiter enable  */
 178
 179 #define CONFIG_PCI                      /* include pci support          */
 180 #define CONFIG_PCI_HOST PCI_HOST_HOST   /* select pci host function     */
 181 #undef  CONFIG_PCI_PNP                  /* do pci plug-and-play         */
 182                                         /* resource configuration       */
 183
 184 #undef  CONFIG_PCI_SCAN_SHOW            /* print pci devices @ startup  */
 185
 186 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE   /* PCI Vendor ID: esd gmbh      */
 187 #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405   /* PCI Device ID: CPCI-405      */
 188 #define CONFIG_SYS_PCI_CLASSCODE        0x0b20  /* PCI Class Code: Processor/PPC*/
 189 #define CONFIG_SYS_PCI_PTM1LA   0x00000000      /* point to sdram               */
 190 #define CONFIG_SYS_PCI_PTM1MS   0xfc000001      /* 64MB, enable hard-wired to 1 */
 191 #define CONFIG_SYS_PCI_PTM1PCI 0x00000000       /* Host: use this pci address   */
 192 #define CONFIG_SYS_PCI_PTM2LA   0xffc00000      /* point to flash               */
 193 #define CONFIG_SYS_PCI_PTM2MS   0xffc00001      /* 4MB, enable                  */
 194 #define CONFIG_SYS_PCI_PTM2PCI 0x04000000       /* Host: use this pci address   */
 195
 196 /*
 197  * For booting Linux, the board info and command line data
 198  * have to be in the first 8 MB of memory, since this is
 199  * the maximum mapped by the Linux kernel during initialization.
 200  */
 201 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* Initial Memory map for Linux */
 202 /*-----------------------------------------------------------------------
 203  * FLASH organization
 204  */
 205 #define FLASH_BASE0_PRELIM      0xFFC00000      /* FLASH bank #0        */
 206
 207 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* max number of memory banks           */
 208 #define CONFIG_SYS_MAX_FLASH_SECT       256     /* max number of sectors on one chip    */
 209
 210 #define CONFIG_SYS_FLASH_ERASE_TOUT     120000  /* Timeout for Flash Erase (in ms)      */
 211 #define CONFIG_SYS_FLASH_WRITE_TOUT     1000    /* Timeout for Flash Write (in ms)      */
 212
 213 #define CONFIG_SYS_FLASH_WORD_SIZE      unsigned short  /* flash word size (width)      */
 214 #define CONFIG_SYS_FLASH_ADDR0          0x5555  /* 1st address for flash config cycles  */
 215 #define CONFIG_SYS_FLASH_ADDR1          0x2AAA  /* 2nd address for flash config cycles  */
 216 /*
 217  * The following defines are added for buggy IOP480 byte interface.
 218  * All other boards should use the standard values (CPCI405 etc.)
 219  */
 220 #define CONFIG_SYS_FLASH_READ0          0x0000  /* 0 is standard                        */
 221 #define CONFIG_SYS_FLASH_READ1          0x0001  /* 1 is standard                        */
 222 #define CONFIG_SYS_FLASH_READ2          0x0002  /* 2 is standard                        */
 223
 224 #define CONFIG_SYS_FLASH_EMPTY_INFO             /* print 'E' for empty sector on flinfo */
 225
 226 #if 0 /* test-only */
 227 #define CONFIG_SYS_JFFS2_FIRST_BANK     0           /* use for JFFS2 */
 228 #define CONFIG_SYS_JFFS2_NUM_BANKS      1           /* ! second bank contains U-Boot */
 229 #endif
 230
 231 /*-----------------------------------------------------------------------
 232  * Start addresses for the final memory configuration
 233  * (Set up by the startup code)
 234  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 235  */
 236 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 237 #define CONFIG_SYS_FLASH_BASE           0xFFFC0000
 238 #define CONFIG_SYS_MONITOR_BASE TEXT_BASE
 239 #define CONFIG_SYS_MONITOR_LEN          (256 * 1024)    /* Reserve 256 kB for Monitor   */
 240 #define CONFIG_SYS_MALLOC_LEN           (256 * 1024)    /* Reserve 256 kB for malloc()  */
 241
 242 #if (CONFIG_SYS_MONITOR_BASE < FLASH_BASE0_PRELIM)
 243 # define CONFIG_SYS_RAMBOOT             1
 244 #else
 245 # undef CONFIG_SYS_RAMBOOT
 246 #endif
 247
 248 /*-----------------------------------------------------------------------
 249  * Environment Variable setup
 250  */
 251 #define CONFIG_ENV_IS_IN_EEPROM 1       /* use EEPROM for environment vars */
 252 #define CONFIG_ENV_OFFSET               0x100   /* environment starts at the beginning of the EEPROM */
 253 #define CONFIG_ENV_SIZE         0x700   /* 2048 bytes may be used for env vars*/
 254                                    /* total size of a CAT24WC16 is 2048 bytes */
 255
 256 /*-----------------------------------------------------------------------
 257  * I2C EEPROM (CAT24WC16) for environment
 258  */
 259 #define CONFIG_HARD_I2C                 /* I2c with hardware support */
 260 #define CONFIG_SYS_I2C_SPEED            100000  /* I2C speed and slave address */
 261 #define CONFIG_SYS_I2C_SLAVE            0x7F
 262
 263 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x50    /* EEPROM CAT28WC08             */
 264 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1        /* Bytes of address             */
 265 /* mask of address bits that overflow into the "EEPROM chip address"    */
 266 #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW     0x07
 267 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4     /* The Catalyst CAT24WC08 has   */
 268                                         /* 16 byte page write mode using*/
 269                                         /* last 4 bits of the address   */
 270 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS   10   /* and takes up to 10 msec */
 271
 272 #define CONFIG_SYS_EEPROM_WREN         1
 273
 274 /*-----------------------------------------------------------------------
 275  * External Bus Controller (EBC) Setup
 276  */
 277 #define CONFIG_SYS_PLD_BASE            0xf0000000
 278 #define CONFIG_SYS_NAND_BASE            0xF4000000  /* NAND FLASH Base Address          */
 279
 280 /* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization                       */
 281 #define CONFIG_SYS_EBC_PB0AP            0x92015480
 282 #define CONFIG_SYS_EBC_PB0CR            0xFFC5A000  /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
 283
 284 /* Memory Bank 1 (Flash Bank 1, NAND-FLASH) initialization                      */
 285 #define CONFIG_SYS_EBC_PB1AP            0x92015480
 286 #define CONFIG_SYS_EBC_PB1CR            0xF4018000  /* BAS=0xF40,BS=1MB,BU=R/W,BW=8bit  */
 287
 288 /* Memory Bank 2 (8 Bit Peripheral: CAN, UART, RTC) initialization              */
 289 #define CONFIG_SYS_EBC_PB2AP            0x010053C0  /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
 290 #define CONFIG_SYS_EBC_PB2CR            0xF0018000  /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit  */
 291
 292 /*-----------------------------------------------------------------------
 293  * FPGA stuff
 294  */
 295 #define CONFIG_SYS_FPGA_XC95XL          1           /* using Xilinx XC95XL CPLD      */
 296 #define CONFIG_SYS_FPGA_MAX_SIZE        32*1024     /* 32kByte is enough for CPLD    */
 297
 298 /* FPGA program pin configuration */
 299 #define CONFIG_SYS_FPGA_PRG             0x04000000  /* JTAG TMS pin (ppc output)     */
 300 #define CONFIG_SYS_FPGA_CLK             0x02000000  /* JTAG TCK pin (ppc output)     */
 301 #define CONFIG_SYS_FPGA_DATA            0x01000000  /* JTAG TDO->TDI data pin (ppc output) */
 302 #define CONFIG_SYS_FPGA_INIT            0x00010000  /* unused (ppc input)            */
 303 #define CONFIG_SYS_FPGA_DONE            0x00008000  /* JTAG TDI->TDO pin (ppc input) */
 304
 305 /*-----------------------------------------------------------------------
 306  * Definitions for initial stack pointer and data area (in data cache)
 307  */
 308 /* use on chip memory ( OCM ) for temperary stack until sdram is tested */
 309 #define CONFIG_SYS_TEMP_STACK_OCM         1
 310
 311 /* On Chip Memory location */
 312 #define CONFIG_SYS_OCM_DATA_ADDR        0xF8000000
 313 #define CONFIG_SYS_OCM_DATA_SIZE        0x1000
 314 #define CONFIG_SYS_INIT_RAM_ADDR        CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM             */
 315 #define CONFIG_SYS_INIT_RAM_END CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM     */
 316
 317 #define CONFIG_SYS_GBL_DATA_SIZE      128  /* size in bytes reserved for initial data */
 318 #define CONFIG_SYS_GBL_DATA_OFFSET    (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
 319 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 320
 321 /*-----------------------------------------------------------------------
 322  * Definitions for GPIO setup (PPC405EP specific)
 323  *
 324  * GPIO0[0]     - External Bus Controller BLAST output
 325  * GPIO0[1-9]   - Instruction trace outputs -> GPIO
 326  * GPIO0[10-13] - External Bus Controller CS_1 - CS_4 outputs
 327  * GPIO0[14-16] - External Bus Controller ABUS3-ABUS5 outputs -> GPIO
 328  * GPIO0[17-23] - External Interrupts IRQ0 - IRQ6 inputs
 329  * GPIO0[24-27] - UART0 control signal inputs/outputs
 330  * GPIO0[28-29] - UART1 data signal input/output
 331  * GPIO0[30-31] - EMAC0 and EMAC1 reject packet inputs
 332  */
 333 /* GPIO Input:          OSR=00, ISR=00, TSR=00, TCR=0 */
 334 /* GPIO Output:         OSR=00, ISR=00, TSR=00, TCR=1 */
 335 /* Alt. Funtion Input:  OSR=00, ISR=01, TSR=00, TCR=0 */
 336 /* Alt. Funtion Output: OSR=01, ISR=00, TSR=00, TCR=1 */
 337 #define CONFIG_SYS_GPIO0_OSRH           0x40000500  /*  0 ... 15 */
 338 #define CONFIG_SYS_GPIO0_OSRL           0x00000110  /* 16 ... 31 */
 339 #define CONFIG_SYS_GPIO0_ISR1H          0x00000000  /*  0 ... 15 */
 340 #define CONFIG_SYS_GPIO0_ISR1L          0x14000045  /* 16 ... 31 */
 341 #define CONFIG_SYS_GPIO0_TSRH           0x00000000  /*  0 ... 15 */
 342 #define CONFIG_SYS_GPIO0_TSRL           0x00000000  /* 16 ... 31 */
 343 #define CONFIG_SYS_GPIO0_TCR            0xF7FE0014  /*  0 ... 31 */
 344
 345 #define CONFIG_SYS_EEPROM_WP            (0x80000000 >> 8)    /* GPIO8 */
 346 #define CONFIG_SYS_PLD_RESET            (0x80000000 >> 12)   /* GPIO12 */
 347
 348 /*
 349  * Internal Definitions
 350  *
 351  * Boot Flags
 352  */
 353 #define BOOTFLAG_COLD   0x01            /* Normal Power-On: Boot from FLASH     */
 354 #define BOOTFLAG_WARM   0x02            /* Software reboot                      */
 355
 356 /*
 357  * Default speed selection (cpu_plb_opb_ebc) in mhz.
 358  * This value will be set if iic boot eprom is disabled.
 359  */
 360 #if 0
 361 #define PLLMR0_DEFAULT   PLLMR0_266_133_66_33
 362 #define PLLMR1_DEFAULT   PLLMR1_266_133_66_33
 363 #endif
 364 #if 0
 365 #define PLLMR0_DEFAULT   PLLMR0_200_100_50_33
 366 #define PLLMR1_DEFAULT   PLLMR1_200_100_50_33
 367 #endif
 368 #if 1
 369 #define PLLMR0_DEFAULT   PLLMR0_133_66_66_33
 370 #define PLLMR1_DEFAULT   PLLMR1_133_66_66_33
 371 #endif
 372
 373 #endif  /* __CONFIG_H */