]> git.ipfire.org Git - people/ms/u-boot.git/blob - include/configs/CPCI405.h
rename CFG_ macros to CONFIG_SYS
[people/ms/u-boot.git] / include / configs / CPCI405.h
1 /*
2 * (C) Copyright 2001
3 * Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
4 *
5 * See file CREDITS for list of people who contributed to this
6 * project.
7 *
8 * This program is free software; you can redistribute it and/or
9 * modify it under the terms of the GNU General Public License as
10 * published by the Free Software Foundation; either version 2 of
11 * the License, or (at your option) any later version.
12 *
13 * This program is distributed in the hope that it will be useful,
14 * but WITHOUT ANY WARRANTY; without even the implied warranty of
15 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
16 * GNU General Public License for more details.
17 *
18 * You should have received a copy of the GNU General Public License
19 * along with this program; if not, write to the Free Software
20 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
21 * MA 02111-1307 USA
22 */
23
24 /*
25 * board/config.h - configuration options, board specific
26 */
27
28 #ifndef __CONFIG_H
29 #define __CONFIG_H
30
31 /*
32 * High Level Configuration Options
33 * (easy to change)
34 */
35
36 #define CONFIG_405GP 1 /* This is a PPC405 CPU */
37 #define CONFIG_4xx 1 /* ...member of PPC4xx family */
38 #define CONFIG_CPCI405 1 /* ...on a CPCI405 board */
39
40 #define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
41
42 #define CONFIG_SYS_CLK_FREQ 33000000 /* external frequency to pll */
43
44 #define CONFIG_BAUDRATE 9600
45 #define CONFIG_BOOTDELAY 3 /* autoboot after 3 seconds */
46
47 #undef CONFIG_BOOTARGS
48 #undef CONFIG_BOOTCOMMAND
49
50 #define CONFIG_PREBOOT /* enable preboot variable */
51
52 #define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
53 #define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
54
55 #define CONFIG_MII 1 /* MII PHY management */
56 #define CONFIG_PHY_ADDR 0 /* PHY address */
57 #define CONFIG_LXT971_NO_SLEEP 1 /* disable sleep mode in LXT971 */
58 #define CONFIG_RESET_PHY_R 1 /* use reset_phy() to disable phy sleep mode */
59
60 #define CONFIG_NET_MULTI 1
61 #undef CONFIG_HAS_ETH1
62
63 /*
64 * BOOTP options
65 */
66 #define CONFIG_BOOTP_SUBNETMASK
67 #define CONFIG_BOOTP_GATEWAY
68 #define CONFIG_BOOTP_HOSTNAME
69 #define CONFIG_BOOTP_BOOTPATH
70 #define CONFIG_BOOTP_DNS
71 #define CONFIG_BOOTP_DNS2
72 #define CONFIG_BOOTP_SEND_HOSTNAME
73
74
75 /*
76 * Command line configuration.
77 */
78 #include <config_cmd_default.h>
79
80 #define CONFIG_CMD_DHCP
81 #define CONFIG_CMD_PCI
82 #define CONFIG_CMD_IRQ
83 #define CONFIG_CMD_IDE
84 #define CONFIG_CMD_FAT
85 #define CONFIG_CMD_ELF
86 #define CONFIG_CMD_MII
87 #define CONFIG_CMD_EEPROM
88
89
90 #define CONFIG_MAC_PARTITION
91 #define CONFIG_DOS_PARTITION
92
93 #define CONFIG_SUPPORT_VFAT
94
95 #undef CONFIG_WATCHDOG /* watchdog disabled */
96
97 #define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
98
99 /*
100 * Miscellaneous configurable options
101 */
102 #define CONFIG_SYS_LONGHELP /* undef to save memory */
103 #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
104
105 #undef CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
106 #ifdef CONFIG_SYS_HUSH_PARSER
107 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
108 #endif
109
110 #if defined(CONFIG_CMD_KGDB)
111 #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
112 #else
113 #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
114 #endif
115 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
116 #define CONFIG_SYS_MAXARGS 16 /* max number of command args */
117 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
118
119 #define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
120
121 #define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
122
123 #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
124 #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
125
126 #undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
127 #define CONFIG_SYS_IGNORE_405_UART_ERRATA_59 /* ignore ppc405gp errata #59 */
128 #define CONFIG_SYS_BASE_BAUD 691200
129
130 /* The following table includes the supported baudrates */
131 #define CONFIG_SYS_BAUDRATE_TABLE \
132 { 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
133 57600, 115200, 230400, 460800, 921600 }
134
135 #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
136 #define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
137
138 #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
139
140 #define CONFIG_LOOPW 1 /* enable loopw command */
141
142 #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
143
144 /*-----------------------------------------------------------------------
145 * PCI stuff
146 *-----------------------------------------------------------------------
147 */
148 #define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
149 #define PCI_HOST_FORCE 1 /* configure as pci host */
150 #define PCI_HOST_AUTO 2 /* detected via arbiter enable */
151
152 #define CONFIG_PCI /* include pci support */
153 #define CONFIG_PCI_HOST PCI_HOST_AUTO /* select pci host function */
154 #define CONFIG_PCI_PNP /* do pci plug-and-play */
155 /* resource configuration */
156
157 #define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
158
159 #define CONFIG_PCI_CONFIG_HOST_BRIDGE 1 /* don't skip host bridge config*/
160
161 #define CONFIG_PCI_BOOTDELAY 0 /* enable pci bootdelay variable*/
162
163 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
164 #define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0405 /* PCI Device ID: CPCI-405 */
165 #define CONFIG_SYS_PCI_SUBSYS_DEVICEID2 0x0406 /* PCI Device ID: CPCI-405-A */
166 #define CONFIG_SYS_PCI_CLASSCODE 0x0b20 /* PCI Class Code: Processor/PPC*/
167 #define CONFIG_SYS_PCI_PTM1LA (bd->bi_memstart) /* point to sdram */
168 #define CONFIG_SYS_PCI_PTM1MS (~(bd->bi_memsize - 1) | 1) /* memsize, enable hard-wired to 1 */
169 #define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
170 #define CONFIG_SYS_PCI_PTM2LA 0xffc00000 /* point to flash */
171 #define CONFIG_SYS_PCI_PTM2MS 0xffc00001 /* 4MB, enable */
172 #define CONFIG_SYS_PCI_PTM2PCI 0x04000000 /* Host: use this pci address */
173
174 /*-----------------------------------------------------------------------
175 * IDE/ATA stuff
176 *-----------------------------------------------------------------------
177 */
178 #undef CONFIG_IDE_8xx_DIRECT /* no pcmcia interface required */
179 #undef CONFIG_IDE_LED /* no led for ide supported */
180 #undef CONFIG_IDE_RESET /* no reset for ide supported */
181
182 #define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE busses */
183 #define CONFIG_SYS_IDE_MAXDEVICE (CONFIG_SYS_IDE_MAXBUS*1) /* max. 1 drives per IDE bus */
184
185 #define CONFIG_SYS_ATA_BASE_ADDR 0xF0100000
186 #define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
187
188 #define CONFIG_SYS_ATA_DATA_OFFSET 0x0000 /* Offset for data I/O */
189 #define CONFIG_SYS_ATA_REG_OFFSET 0x0000 /* Offset for normal register accesses */
190 #define CONFIG_SYS_ATA_ALT_OFFSET 0x0000 /* Offset for alternate registers */
191
192 /*-----------------------------------------------------------------------
193 * Start addresses for the final memory configuration
194 * (Set up by the startup code)
195 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
196 */
197 #define CONFIG_SYS_SDRAM_BASE 0x00000000
198 #define CONFIG_SYS_FLASH_BASE 0xFFFD0000
199 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
200 #define CONFIG_SYS_MONITOR_LEN (192 * 1024) /* Reserve 196 kB for Monitor */
201 #define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
202
203 /*
204 * For booting Linux, the board info and command line data
205 * have to be in the first 8 MB of memory, since this is
206 * the maximum mapped by the Linux kernel during initialization.
207 */
208 #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
209 /*-----------------------------------------------------------------------
210 * FLASH organization
211 */
212 #define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
213 #define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
214
215 #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
216 #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
217
218 #define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
219 #define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
220 #define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
221 /*
222 * The following defines are added for buggy IOP480 byte interface.
223 * All other boards should use the standard values (CPCI405 etc.)
224 */
225 #define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */
226 #define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */
227 #define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */
228
229 #define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
230
231 #define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */
232 #define CONFIG_SYS_NVRAM_SIZE (32*1024) /* NVRAM size */
233 #define CONFIG_SYS_VXWORKS_MAC_PTR (CONFIG_SYS_NVRAM_BASE_ADDR+0x6900) /* VxWorks eth-addr*/
234
235 #if 1 /* Use NVRAM for environment variables */
236 /*-----------------------------------------------------------------------
237 * NVRAM organization
238 */
239 #define CONFIG_ENV_IS_IN_NVRAM 1 /* use NVRAM for environment vars */
240 #define CONFIG_ENV_SIZE 0x1000 /* Size of Environment vars */
241 #define CONFIG_ENV_ADDR \
242 (CONFIG_SYS_NVRAM_BASE_ADDR+CONFIG_SYS_NVRAM_SIZE-CONFIG_ENV_SIZE) /* Env */
243
244 #else /* Use EEPROM for environment variables */
245
246 #define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
247 #define CONFIG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
248 #define CONFIG_ENV_SIZE 0x400 /* 1024 bytes may be used for env vars */
249 /* total size of a CAT24WC08 is 1024 bytes */
250 #endif
251
252 /*-----------------------------------------------------------------------
253 * I2C EEPROM (CAT24WC08) for environment
254 */
255 #define CONFIG_HARD_I2C /* I2c with hardware support */
256 #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
257 #define CONFIG_SYS_I2C_SLAVE 0x7F
258
259 #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
260 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
261 /* mask of address bits that overflow into the "EEPROM chip address" */
262 #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
263 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
264 /* 16 byte page write mode using*/
265 /* last 4 bits of the address */
266 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
267
268 /*
269 * Init Memory Controller:
270 *
271 * BR0/1 and OR0/1 (FLASH)
272 */
273
274 #define FLASH_BASE0_PRELIM 0xFF800000 /* FLASH bank #0 */
275 #define FLASH_BASE1_PRELIM 0xFFC00000 /* FLASH bank #1 */
276
277 /*-----------------------------------------------------------------------
278 * External Bus Controller (EBC) Setup
279 */
280
281 /* Memory Bank 0 (Flash Bank 0) initialization */
282 #define CONFIG_SYS_EBC_PB0AP 0x92015480
283 #define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
284
285 /* Memory Bank 1 (Flash Bank 1) initialization */
286 #define CONFIG_SYS_EBC_PB1AP 0x92015480
287 #define CONFIG_SYS_EBC_PB1CR 0xFF85A000 /* BAS=0xFF8,BS=4MB,BU=R/W,BW=16bit */
288
289 /* Memory Bank 2 (CAN0, 1, 2, Codeswitch) initialization */
290 #define CONFIG_SYS_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
291 #define CONFIG_SYS_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
292
293 /* Memory Bank 3 (CompactFlash IDE) initialization */
294 #define CONFIG_SYS_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
295 #define CONFIG_SYS_EBC_PB3CR 0xF011A000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=16bit */
296
297 /* Memory Bank 4 (NVRAM) initialization */
298 #define CONFIG_SYS_EBC_PB4AP 0x01005280 /* TWT=2,WBN=1,WBF=1,TH=1,SOR=1 */
299 #define CONFIG_SYS_EBC_PB4CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */
300
301 /* Memory Bank 5 (Quart) initialization */
302 #define CONFIG_SYS_EBC_PB5AP 0x04005B80 /* TWT=8,WBN=1,WBF=1,TH=5,RE=1,SOR=1*/
303 #define CONFIG_SYS_EBC_PB5CR 0xF0318000 /* BAS=0xF03,BS=1MB,BU=R/W,BW=8bit */
304
305 /*-----------------------------------------------------------------------
306 * FPGA stuff
307 */
308
309 /* FPGA program pin configuration */
310 #define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
311 #define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
312 #define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
313 #define CONFIG_SYS_FPGA_INIT 0x00400000 /* FPGA init pin (ppc input) */
314 #define CONFIG_SYS_FPGA_DONE 0x00800000 /* FPGA done pin (ppc input) */
315
316 /*-----------------------------------------------------------------------
317 * Definitions for initial stack pointer and data area (in data cache)
318 */
319 #if 1 /* test-only */
320 #define CONFIG_SYS_INIT_DCACHE_CS 7 /* use cs # 7 for data cache memory */
321
322 #define CONFIG_SYS_INIT_RAM_ADDR 0x40000000 /* use data cache */
323 #else
324 #define CONFIG_SYS_INIT_RAM_ADDR 0x00df0000 /* inside of SDRAM */
325 #endif
326 #define CONFIG_SYS_INIT_RAM_END 0x2000 /* End of used area in RAM */
327 #define CONFIG_SYS_GBL_DATA_SIZE 128 /* size in bytes reserved for initial data */
328 #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
329 #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
330
331
332 /*
333 * Internal Definitions
334 *
335 * Boot Flags
336 */
337 #define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
338 #define BOOTFLAG_WARM 0x02 /* Software reboot */
339
340 #endif /* __CONFIG_H */