include/configs/M5485EVB.h

   1 /*
   2  * Configuation settings for the Freescale MCF5485 FireEngine board.
   3  *
   4  * Copyright (C) 2004-2008 Freescale Semiconductor, Inc.
   5  * TsiChung Liew (Tsi-Chung.Liew@freescale.com)
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 /*
  11  * board/config.h - configuration options, board specific
  12  */
  13
  14 #ifndef _M5485EVB_H
  15 #define _M5485EVB_H
  16
  17 /*
  18  * High Level Configuration Options
  19  * (easy to change)
  20  */
  21
  22 #define CONFIG_DISPLAY_BOARDINFO
  23
  24 #define CONFIG_MCFUART
  25 #define CONFIG_SYS_UART_PORT            (0)
  26 #define CONFIG_BAUDRATE         115200
  27
  28 #undef CONFIG_HW_WATCHDOG
  29 #define CONFIG_WATCHDOG_TIMEOUT 5000    /* timeout in milliseconds, max timeout is 6.71sec */
  30
  31 /* Command line configuration */
  32 #include <config_cmd_default.h>
  33
  34 #define CONFIG_CMD_CACHE
  35 #undef CONFIG_CMD_DATE
  36 #define CONFIG_CMD_ELF
  37 #define CONFIG_CMD_FLASH
  38 #define CONFIG_CMD_I2C
  39 #define CONFIG_CMD_MEMORY
  40 #define CONFIG_CMD_MISC
  41 #define CONFIG_CMD_MII
  42 #define CONFIG_CMD_PCI
  43 #define CONFIG_CMD_PING
  44 #define CONFIG_CMD_REGINFO
  45 #define CONFIG_CMD_USB
  46
  47 #define CONFIG_SLTTMR
  48
  49 #define CONFIG_FSLDMAFEC
  50 #ifdef CONFIG_FSLDMAFEC
  51 #       define CONFIG_MII               1
  52 #       define CONFIG_MII_INIT          1
  53 #       define CONFIG_HAS_ETH1
  54
  55 #       define CONFIG_SYS_DMA_USE_INTSRAM       1
  56 #       define CONFIG_SYS_DISCOVER_PHY
  57 #       define CONFIG_SYS_RX_ETH_BUFFER 32
  58 #       define CONFIG_SYS_TX_ETH_BUFFER 48
  59 #       define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  60
  61 #       define CONFIG_SYS_FEC0_PINMUX           0
  62 #       define CONFIG_SYS_FEC0_MIIBASE          CONFIG_SYS_FEC0_IOBASE
  63 #       define CONFIG_SYS_FEC1_PINMUX           0
  64 #       define CONFIG_SYS_FEC1_MIIBASE          CONFIG_SYS_FEC0_IOBASE
  65
  66 #       define MCFFEC_TOUT_LOOP         50000
  67 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
  68 #       ifndef CONFIG_SYS_DISCOVER_PHY
  69 #               define FECDUPLEX        FULL
  70 #               define FECSPEED         _100BASET
  71 #       else
  72 #               ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  73 #                       define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  74 #               endif
  75 #       endif                   /* CONFIG_SYS_DISCOVER_PHY */
  76
  77 #       define CONFIG_IPADDR    192.162.1.2
  78 #       define CONFIG_NETMASK   255.255.255.0
  79 #       define CONFIG_SERVERIP  192.162.1.1
  80 #       define CONFIG_GATEWAYIP 192.162.1.1
  81
  82 #endif
  83
  84 #ifdef CONFIG_CMD_USB
  85 #       define CONFIG_USB_STORAGE
  86 #       define CONFIG_DOS_PARTITION
  87 #       define CONFIG_USB_OHCI_NEW
  88 #       ifndef CONFIG_CMD_PCI
  89 #               define CONFIG_CMD_PCI
  90 #       endif
  91 /*#     define CONFIG_PCI_OHCI*/
  92 #       define CONFIG_SYS_USB_OHCI_REGS_BASE            0x80041000
  93 #       define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS       15
  94 #       define CONFIG_SYS_USB_OHCI_SLOT_NAME            "isp1561"
  95 #       define CONFIG_SYS_OHCI_SWAP_REG_ACCESS
  96 #endif
  97
  98 /* I2C */
  99 #define CONFIG_SYS_I2C
 100 #define CONFIG_SYS_I2C_FSL
 101 #define CONFIG_SYS_FSL_I2C_SPEED        80000
 102 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 103 #define CONFIG_SYS_FSL_I2C_OFFSET       0x00008F00
 104 #define CONFIG_SYS_IMMR         CONFIG_SYS_MBAR
 105
 106 /* PCI */
 107 #ifdef CONFIG_CMD_PCI
 108 #define CONFIG_PCI              1
 109 #define CONFIG_PCI_PNP          1
 110 #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
 111
 112 #define CONFIG_SYS_PCI_MEM_BUS          0x80000000
 113 #define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BUS
 114 #define CONFIG_SYS_PCI_MEM_SIZE 0x10000000
 115
 116 #define CONFIG_SYS_PCI_IO_BUS           0x71000000
 117 #define CONFIG_SYS_PCI_IO_PHYS          CONFIG_SYS_PCI_IO_BUS
 118 #define CONFIG_SYS_PCI_IO_SIZE          0x01000000
 119
 120 #define CONFIG_SYS_PCI_CFG_BUS          0x70000000
 121 #define CONFIG_SYS_PCI_CFG_PHYS CONFIG_SYS_PCI_CFG_BUS
 122 #define CONFIG_SYS_PCI_CFG_SIZE 0x01000000
 123 #endif
 124
 125 #define CONFIG_BOOTDELAY        1       /* autoboot after 5 seconds */
 126 #define CONFIG_UDP_CHECKSUM
 127
 128 #define CONFIG_HOSTNAME         M548xEVB
 129 #define CONFIG_EXTRA_ENV_SETTINGS               \
 130         "netdev=eth0\0"                         \
 131         "loadaddr=10000\0"                      \
 132         "u-boot=u-boot.bin\0"                   \
 133         "load=tftp ${loadaddr) ${u-boot}\0"     \
 134         "upd=run load; run prog\0"              \
 135         "prog=prot off bank 1;"                 \
 136         "era ff800000 ff83ffff;"                \
 137         "cp.b ${loadaddr} ff800000 ${filesize};"\
 138         "save\0"                                \
 139         ""
 140
 141 #define CONFIG_PRAM             512     /* 512 KB */
 142 #define CONFIG_SYS_PROMPT               "-> "
 143 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 144
 145 #ifdef CONFIG_CMD_KGDB
 146 #       define CONFIG_SYS_CBSIZE        1024    /* Console I/O Buffer Size */
 147 #else
 148 #       define CONFIG_SYS_CBSIZE        256     /* Console I/O Buffer Size */
 149 #endif
 150
 151 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)        /* Print Buffer Size */
 152 #define CONFIG_SYS_MAXARGS              16      /* max number of command args */
 153 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 154 #define CONFIG_SYS_LOAD_ADDR            0x00010000
 155
 156 #define CONFIG_SYS_CLK                  CONFIG_SYS_BUSCLK
 157 #define CONFIG_SYS_CPU_CLK              CONFIG_SYS_CLK * 2
 158
 159 #define CONFIG_SYS_MBAR         0xF0000000
 160 #define CONFIG_SYS_INTSRAM              (CONFIG_SYS_MBAR + 0x10000)
 161 #define CONFIG_SYS_INTSRAMSZ            0x8000
 162
 163 /*#define CONFIG_SYS_LATCH_ADDR         (CONFIG_SYS_CS1_BASE + 0x80000)*/
 164
 165 /*
 166  * Low Level Configuration Settings
 167  * (address mappings, register initial values, etc.)
 168  * You should know what you are doing if you make changes here.
 169  */
 170 /*-----------------------------------------------------------------------
 171  * Definitions for initial stack pointer and data area (in DPRAM)
 172  */
 173 #define CONFIG_SYS_INIT_RAM_ADDR        0xF2000000
 174 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000  /* Size of used area in internal SRAM */
 175 #define CONFIG_SYS_INIT_RAM_CTRL        0x21
 176 #define CONFIG_SYS_INIT_RAM1_ADDR       (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE)
 177 #define CONFIG_SYS_INIT_RAM1_END        0x1000  /* End of used area in internal SRAM */
 178 #define CONFIG_SYS_INIT_RAM1_CTRL       0x21
 179 #define CONFIG_SYS_GBL_DATA_OFFSET      ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10)
 180 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 181
 182 /*-----------------------------------------------------------------------
 183  * Start addresses for the final memory configuration
 184  * (Set up by the startup code)
 185  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 186  */
 187 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 188 #define CONFIG_SYS_SDRAM_CFG1           0x73711630
 189 #define CONFIG_SYS_SDRAM_CFG2           0x46770000
 190 #define CONFIG_SYS_SDRAM_CTRL           0xE10B0000
 191 #define CONFIG_SYS_SDRAM_EMOD           0x40010000
 192 #define CONFIG_SYS_SDRAM_MODE           0x018D0000
 193 #define CONFIG_SYS_SDRAM_DRVSTRENGTH    0x000002AA
 194 #ifdef CONFIG_SYS_DRAMSZ1
 195 #       define CONFIG_SYS_SDRAM_SIZE    (CONFIG_SYS_DRAMSZ + CONFIG_SYS_DRAMSZ1)
 196 #else
 197 #       define CONFIG_SYS_SDRAM_SIZE    CONFIG_SYS_DRAMSZ
 198 #endif
 199
 200 #define CONFIG_SYS_MEMTEST_START        CONFIG_SYS_SDRAM_BASE + 0x400
 201 #define CONFIG_SYS_MEMTEST_END          ((CONFIG_SYS_SDRAM_SIZE - 3) << 20)
 202
 203 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
 204 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)     /* Reserve 256 kB for Monitor */
 205
 206 #define CONFIG_SYS_BOOTPARAMS_LEN       64*1024
 207
 208 /* Reserve 256 kB for malloc() */
 209 #define CONFIG_SYS_MALLOC_LEN           (256 << 10)
 210 /*
 211  * For booting Linux, the board info and command line data
 212  * have to be in the first 8 MB of memory, since this is
 213  * the maximum mapped by the Linux kernel during initialization ??
 214  */
 215 #define CONFIG_SYS_BOOTMAPSZ            (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
 216
 217 /*-----------------------------------------------------------------------
 218  * FLASH organization
 219  */
 220 #define CONFIG_SYS_FLASH_CFI
 221 #ifdef CONFIG_SYS_FLASH_CFI
 222 #       define CONFIG_SYS_FLASH_BASE            (CONFIG_SYS_CS0_BASE)
 223 #       define CONFIG_FLASH_CFI_DRIVER  1
 224 #       define CONFIG_SYS_FLASH_CFI_WIDTH       FLASH_CFI_16BIT
 225 #       define CONFIG_SYS_MAX_FLASH_SECT        137     /* max number of sectors on one chip */
 226 #       define CONFIG_SYS_FLASH_PROTECTION      /* "Real" (hardware) sectors protection */
 227 #       define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 228 #ifdef CONFIG_SYS_NOR1SZ
 229 #       define CONFIG_SYS_MAX_FLASH_BANKS       2       /* max number of memory banks */
 230 #       define CONFIG_SYS_FLASH_SIZE            ((CONFIG_SYS_NOR1SZ + CONFIG_SYS_BOOTSZ) << 20)
 231 #       define CONFIG_SYS_FLASH_BANKS_LIST      { CONFIG_SYS_CS0_BASE, CONFIG_SYS_CS1_BASE }
 232 #else
 233 #       define CONFIG_SYS_MAX_FLASH_BANKS       1       /* max number of memory banks */
 234 #       define CONFIG_SYS_FLASH_SIZE            (CONFIG_SYS_BOOTSZ << 20)
 235 #endif
 236 #endif
 237
 238 /* Configuration for environment
 239  * Environment is not embedded in u-boot. First time runing may have env
 240  * crc error warning if there is no correct environment on the flash.
 241  */
 242 #define CONFIG_ENV_OFFSET               0x40000
 243 #define CONFIG_ENV_SECT_SIZE    0x10000
 244 #define CONFIG_ENV_IS_IN_FLASH  1
 245
 246 /*-----------------------------------------------------------------------
 247  * Cache Configuration
 248  */
 249 #define CONFIG_SYS_CACHELINE_SIZE       16
 250
 251 #define ICACHE_STATUS                   (CONFIG_SYS_INIT_RAM_ADDR + \
 252                                          CONFIG_SYS_INIT_RAM_SIZE - 8)
 253 #define DCACHE_STATUS                   (CONFIG_SYS_INIT_RAM_ADDR + \
 254                                          CONFIG_SYS_INIT_RAM_SIZE - 4)
 255 #define CONFIG_SYS_ICACHE_INV           (CF_CACR_BCINVA + CF_CACR_ICINVA + \
 256                                          CF_CACR_IDCM)
 257 #define CONFIG_SYS_DCACHE_INV           (CF_CACR_DCINVA)
 258 #define CONFIG_SYS_CACHE_ACR2           (CONFIG_SYS_SDRAM_BASE | \
 259                                          CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
 260                                          CF_ACR_EN | CF_ACR_SM_ALL)
 261 #define CONFIG_SYS_CACHE_ICACR          (CF_CACR_BEC | CF_CACR_BCINVA | \
 262                                          CF_CACR_IEC | CF_CACR_ICINVA)
 263 #define CONFIG_SYS_CACHE_DCACR          ((CONFIG_SYS_CACHE_ICACR | \
 264                                          CF_CACR_DEC | CF_CACR_DDCM_P | \
 265                                          CF_CACR_DCINVA) & ~CF_CACR_ICINVA)
 266
 267 /*-----------------------------------------------------------------------
 268  * Chipselect bank definitions
 269  */
 270 /*
 271  * CS0 - NOR Flash 1, 2, 4, or 8MB
 272  * CS1 - NOR Flash
 273  * CS2 - Available
 274  * CS3 - Available
 275  * CS4 - Available
 276  * CS5 - Available
 277  */
 278 #define CONFIG_SYS_CS0_BASE             0xFF800000
 279 #define CONFIG_SYS_CS0_MASK             (((CONFIG_SYS_BOOTSZ << 20) - 1) & 0xFFFF0001)
 280 #define CONFIG_SYS_CS0_CTRL             0x00101980
 281
 282 #ifdef CONFIG_SYS_NOR1SZ
 283 #define CONFIG_SYS_CS1_BASE             0xE0000000
 284 #define CONFIG_SYS_CS1_MASK             (((CONFIG_SYS_NOR1SZ << 20) - 1) & 0xFFFF0001)
 285 #define CONFIG_SYS_CS1_CTRL             0x00101D80
 286 #endif
 287
 288 #endif                          /* _M5485EVB_H */