include/configs/M5485EVB.h

   1 /*
   2  * Configuation settings for the Freescale MCF5485 FireEngine board.
   3  *
   4  * Copyright (C) 2004-2008 Freescale Semiconductor, Inc.
   5  * TsiChung Liew (Tsi-Chung.Liew@freescale.com)
   6  *
   7  * SPDX-License-Identifier:     GPL-2.0+
   8  */
   9
  10 /*
  11  * board/config.h - configuration options, board specific
  12  */
  13
  14 #ifndef _M5485EVB_H
  15 #define _M5485EVB_H
  16
  17 /*
  18  * High Level Configuration Options
  19  * (easy to change)
  20  */
  21
  22 #define CONFIG_DISPLAY_BOARDINFO
  23
  24 #define CONFIG_MCFUART
  25 #define CONFIG_SYS_UART_PORT            (0)
  26 #define CONFIG_BAUDRATE         115200
  27
  28 #undef CONFIG_HW_WATCHDOG
  29 #define CONFIG_WATCHDOG_TIMEOUT 5000    /* timeout in milliseconds, max timeout is 6.71sec */
  30
  31 /* Command line configuration */
  32 #include <config_cmd_default.h>
  33
  34 #define CONFIG_CMD_CACHE
  35 #undef CONFIG_CMD_DATE
  36 #define CONFIG_CMD_ELF
  37 #define CONFIG_CMD_FLASH
  38 #define CONFIG_CMD_I2C
  39 #define CONFIG_CMD_MEMORY
  40 #define CONFIG_CMD_MISC
  41 #define CONFIG_CMD_MII
  42 #define CONFIG_CMD_NET
  43 #define CONFIG_CMD_PCI
  44 #define CONFIG_CMD_PING
  45 #define CONFIG_CMD_REGINFO
  46 #define CONFIG_CMD_USB
  47
  48 #define CONFIG_SLTTMR
  49
  50 #define CONFIG_FSLDMAFEC
  51 #ifdef CONFIG_FSLDMAFEC
  52 #       define CONFIG_MII               1
  53 #       define CONFIG_MII_INIT          1
  54 #       define CONFIG_HAS_ETH1
  55
  56 #       define CONFIG_SYS_DMA_USE_INTSRAM       1
  57 #       define CONFIG_SYS_DISCOVER_PHY
  58 #       define CONFIG_SYS_RX_ETH_BUFFER 32
  59 #       define CONFIG_SYS_TX_ETH_BUFFER 48
  60 #       define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  61
  62 #       define CONFIG_SYS_FEC0_PINMUX           0
  63 #       define CONFIG_SYS_FEC0_MIIBASE          CONFIG_SYS_FEC0_IOBASE
  64 #       define CONFIG_SYS_FEC1_PINMUX           0
  65 #       define CONFIG_SYS_FEC1_MIIBASE          CONFIG_SYS_FEC0_IOBASE
  66
  67 #       define MCFFEC_TOUT_LOOP         50000
  68 /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
  69 #       ifndef CONFIG_SYS_DISCOVER_PHY
  70 #               define FECDUPLEX        FULL
  71 #               define FECSPEED         _100BASET
  72 #       else
  73 #               ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  74 #                       define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
  75 #               endif
  76 #       endif                   /* CONFIG_SYS_DISCOVER_PHY */
  77
  78 #       define CONFIG_ETHADDR   00:e0:0c:bc:e5:60
  79 #       define CONFIG_ETH1ADDR  00:e0:0c:bc:e5:61
  80 #       define CONFIG_IPADDR    192.162.1.2
  81 #       define CONFIG_NETMASK   255.255.255.0
  82 #       define CONFIG_SERVERIP  192.162.1.1
  83 #       define CONFIG_GATEWAYIP 192.162.1.1
  84 #       define CONFIG_OVERWRITE_ETHADDR_ONCE
  85
  86 #endif
  87
  88 #ifdef CONFIG_CMD_USB
  89 #       define CONFIG_USB_STORAGE
  90 #       define CONFIG_DOS_PARTITION
  91 #       define CONFIG_USB_OHCI_NEW
  92 #       ifndef CONFIG_CMD_PCI
  93 #               define CONFIG_CMD_PCI
  94 #       endif
  95 /*#     define CONFIG_PCI_OHCI*/
  96 #       define CONFIG_SYS_USB_OHCI_REGS_BASE            0x80041000
  97 #       define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS       15
  98 #       define CONFIG_SYS_USB_OHCI_SLOT_NAME            "isp1561"
  99 #       define CONFIG_SYS_OHCI_SWAP_REG_ACCESS
 100 #endif
 101
 102 /* I2C */
 103 #define CONFIG_SYS_I2C
 104 #define CONFIG_SYS_I2C_FSL
 105 #define CONFIG_SYS_FSL_I2C_SPEED        80000
 106 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 107 #define CONFIG_SYS_FSL_I2C_OFFSET       0x00008F00
 108 #define CONFIG_SYS_IMMR         CONFIG_SYS_MBAR
 109
 110 /* PCI */
 111 #ifdef CONFIG_CMD_PCI
 112 #define CONFIG_PCI              1
 113 #define CONFIG_PCI_PNP          1
 114 #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
 115
 116 #define CONFIG_SYS_PCI_MEM_BUS          0x80000000
 117 #define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BUS
 118 #define CONFIG_SYS_PCI_MEM_SIZE 0x10000000
 119
 120 #define CONFIG_SYS_PCI_IO_BUS           0x71000000
 121 #define CONFIG_SYS_PCI_IO_PHYS          CONFIG_SYS_PCI_IO_BUS
 122 #define CONFIG_SYS_PCI_IO_SIZE          0x01000000
 123
 124 #define CONFIG_SYS_PCI_CFG_BUS          0x70000000
 125 #define CONFIG_SYS_PCI_CFG_PHYS CONFIG_SYS_PCI_CFG_BUS
 126 #define CONFIG_SYS_PCI_CFG_SIZE 0x01000000
 127 #endif
 128
 129 #define CONFIG_BOOTDELAY        1       /* autoboot after 5 seconds */
 130 #define CONFIG_UDP_CHECKSUM
 131
 132 #define CONFIG_HOSTNAME         M548xEVB
 133 #define CONFIG_EXTRA_ENV_SETTINGS               \
 134         "netdev=eth0\0"                         \
 135         "loadaddr=10000\0"                      \
 136         "u-boot=u-boot.bin\0"                   \
 137         "load=tftp ${loadaddr) ${u-boot}\0"     \
 138         "upd=run load; run prog\0"              \
 139         "prog=prot off bank 1;"                 \
 140         "era ff800000 ff83ffff;"                \
 141         "cp.b ${loadaddr} ff800000 ${filesize};"\
 142         "save\0"                                \
 143         ""
 144
 145 #define CONFIG_PRAM             512     /* 512 KB */
 146 #define CONFIG_SYS_PROMPT               "-> "
 147 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 148
 149 #ifdef CONFIG_CMD_KGDB
 150 #       define CONFIG_SYS_CBSIZE        1024    /* Console I/O Buffer Size */
 151 #else
 152 #       define CONFIG_SYS_CBSIZE        256     /* Console I/O Buffer Size */
 153 #endif
 154
 155 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)        /* Print Buffer Size */
 156 #define CONFIG_SYS_MAXARGS              16      /* max number of command args */
 157 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
 158 #define CONFIG_SYS_LOAD_ADDR            0x00010000
 159
 160 #define CONFIG_SYS_CLK                  CONFIG_SYS_BUSCLK
 161 #define CONFIG_SYS_CPU_CLK              CONFIG_SYS_CLK * 2
 162
 163 #define CONFIG_SYS_MBAR         0xF0000000
 164 #define CONFIG_SYS_INTSRAM              (CONFIG_SYS_MBAR + 0x10000)
 165 #define CONFIG_SYS_INTSRAMSZ            0x8000
 166
 167 /*#define CONFIG_SYS_LATCH_ADDR         (CONFIG_SYS_CS1_BASE + 0x80000)*/
 168
 169 /*
 170  * Low Level Configuration Settings
 171  * (address mappings, register initial values, etc.)
 172  * You should know what you are doing if you make changes here.
 173  */
 174 /*-----------------------------------------------------------------------
 175  * Definitions for initial stack pointer and data area (in DPRAM)
 176  */
 177 #define CONFIG_SYS_INIT_RAM_ADDR        0xF2000000
 178 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000  /* Size of used area in internal SRAM */
 179 #define CONFIG_SYS_INIT_RAM_CTRL        0x21
 180 #define CONFIG_SYS_INIT_RAM1_ADDR       (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_RAM_SIZE)
 181 #define CONFIG_SYS_INIT_RAM1_END        0x1000  /* End of used area in internal SRAM */
 182 #define CONFIG_SYS_INIT_RAM1_CTRL       0x21
 183 #define CONFIG_SYS_GBL_DATA_OFFSET      ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10)
 184 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 185
 186 /*-----------------------------------------------------------------------
 187  * Start addresses for the final memory configuration
 188  * (Set up by the startup code)
 189  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 190  */
 191 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 192 #define CONFIG_SYS_SDRAM_CFG1           0x73711630
 193 #define CONFIG_SYS_SDRAM_CFG2           0x46770000
 194 #define CONFIG_SYS_SDRAM_CTRL           0xE10B0000
 195 #define CONFIG_SYS_SDRAM_EMOD           0x40010000
 196 #define CONFIG_SYS_SDRAM_MODE           0x018D0000
 197 #define CONFIG_SYS_SDRAM_DRVSTRENGTH    0x000002AA
 198 #ifdef CONFIG_SYS_DRAMSZ1
 199 #       define CONFIG_SYS_SDRAM_SIZE    (CONFIG_SYS_DRAMSZ + CONFIG_SYS_DRAMSZ1)
 200 #else
 201 #       define CONFIG_SYS_SDRAM_SIZE    CONFIG_SYS_DRAMSZ
 202 #endif
 203
 204 #define CONFIG_SYS_MEMTEST_START        CONFIG_SYS_SDRAM_BASE + 0x400
 205 #define CONFIG_SYS_MEMTEST_END          ((CONFIG_SYS_SDRAM_SIZE - 3) << 20)
 206
 207 #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
 208 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)     /* Reserve 256 kB for Monitor */
 209
 210 #define CONFIG_SYS_BOOTPARAMS_LEN       64*1024
 211
 212 /* Reserve 256 kB for malloc() */
 213 #define CONFIG_SYS_MALLOC_LEN           (256 << 10)
 214 /*
 215  * For booting Linux, the board info and command line data
 216  * have to be in the first 8 MB of memory, since this is
 217  * the maximum mapped by the Linux kernel during initialization ??
 218  */
 219 #define CONFIG_SYS_BOOTMAPSZ            (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
 220
 221 /*-----------------------------------------------------------------------
 222  * FLASH organization
 223  */
 224 #define CONFIG_SYS_FLASH_CFI
 225 #ifdef CONFIG_SYS_FLASH_CFI
 226 #       define CONFIG_SYS_FLASH_BASE            (CONFIG_SYS_CS0_BASE)
 227 #       define CONFIG_FLASH_CFI_DRIVER  1
 228 #       define CONFIG_SYS_FLASH_CFI_WIDTH       FLASH_CFI_16BIT
 229 #       define CONFIG_SYS_MAX_FLASH_SECT        137     /* max number of sectors on one chip */
 230 #       define CONFIG_SYS_FLASH_PROTECTION      /* "Real" (hardware) sectors protection */
 231 #       define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 232 #ifdef CONFIG_SYS_NOR1SZ
 233 #       define CONFIG_SYS_MAX_FLASH_BANKS       2       /* max number of memory banks */
 234 #       define CONFIG_SYS_FLASH_SIZE            ((CONFIG_SYS_NOR1SZ + CONFIG_SYS_BOOTSZ) << 20)
 235 #       define CONFIG_SYS_FLASH_BANKS_LIST      { CONFIG_SYS_CS0_BASE, CONFIG_SYS_CS1_BASE }
 236 #else
 237 #       define CONFIG_SYS_MAX_FLASH_BANKS       1       /* max number of memory banks */
 238 #       define CONFIG_SYS_FLASH_SIZE            (CONFIG_SYS_BOOTSZ << 20)
 239 #endif
 240 #endif
 241
 242 /* Configuration for environment
 243  * Environment is not embedded in u-boot. First time runing may have env
 244  * crc error warning if there is no correct environment on the flash.
 245  */
 246 #define CONFIG_ENV_OFFSET               0x40000
 247 #define CONFIG_ENV_SECT_SIZE    0x10000
 248 #define CONFIG_ENV_IS_IN_FLASH  1
 249
 250 /*-----------------------------------------------------------------------
 251  * Cache Configuration
 252  */
 253 #define CONFIG_SYS_CACHELINE_SIZE       16
 254
 255 #define ICACHE_STATUS                   (CONFIG_SYS_INIT_RAM_ADDR + \
 256                                          CONFIG_SYS_INIT_RAM_SIZE - 8)
 257 #define DCACHE_STATUS                   (CONFIG_SYS_INIT_RAM_ADDR + \
 258                                          CONFIG_SYS_INIT_RAM_SIZE - 4)
 259 #define CONFIG_SYS_ICACHE_INV           (CF_CACR_BCINVA + CF_CACR_ICINVA + \
 260                                          CF_CACR_IDCM)
 261 #define CONFIG_SYS_DCACHE_INV           (CF_CACR_DCINVA)
 262 #define CONFIG_SYS_CACHE_ACR2           (CONFIG_SYS_SDRAM_BASE | \
 263                                          CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
 264                                          CF_ACR_EN | CF_ACR_SM_ALL)
 265 #define CONFIG_SYS_CACHE_ICACR          (CF_CACR_BEC | CF_CACR_BCINVA | \
 266                                          CF_CACR_IEC | CF_CACR_ICINVA)
 267 #define CONFIG_SYS_CACHE_DCACR          ((CONFIG_SYS_CACHE_ICACR | \
 268                                          CF_CACR_DEC | CF_CACR_DDCM_P | \
 269                                          CF_CACR_DCINVA) & ~CF_CACR_ICINVA)
 270
 271 /*-----------------------------------------------------------------------
 272  * Chipselect bank definitions
 273  */
 274 /*
 275  * CS0 - NOR Flash 1, 2, 4, or 8MB
 276  * CS1 - NOR Flash
 277  * CS2 - Available
 278  * CS3 - Available
 279  * CS4 - Available
 280  * CS5 - Available
 281  */
 282 #define CONFIG_SYS_CS0_BASE             0xFF800000
 283 #define CONFIG_SYS_CS0_MASK             (((CONFIG_SYS_BOOTSZ << 20) - 1) & 0xFFFF0001)
 284 #define CONFIG_SYS_CS0_CTRL             0x00101980
 285
 286 #ifdef CONFIG_SYS_NOR1SZ
 287 #define CONFIG_SYS_CS1_BASE             0xE0000000
 288 #define CONFIG_SYS_CS1_MASK             (((CONFIG_SYS_NOR1SZ << 20) - 1) & 0xFFFF0001)
 289 #define CONFIG_SYS_CS1_CTRL             0x00101D80
 290 #endif
 291
 292 #endif                          /* _M5485EVB_H */