include/configs/MBX860T.h

   1  /*
   2   * A collection of structures, addresses, and values associated with
   3   * the Motorola 860T MBX board.
   4   * Copied from the FADS stuff, which was originally copied from the MBX stuff!
   5   * Magnus Damm added defines for 8xxrom and extended bd_info.
   6   * Helmut Buchsbaum added bitvalues for BCSRx
   7   * Rob Taylor coverted it back to MBX
   8   *
   9   * Copyright (c) 1998 Dan Malek (dmalek@jlc.net)
  10   */
  11
  12 /* ------------------------------------------------------------------------- */
  13
  14 /*
  15  * board/config.h - configuration options, board specific
  16  */
  17
  18 #ifndef __CONFIG_H
  19 #define __CONFIG_H
  20
  21 /*
  22  * High Level Configuration Options
  23  * (easy to change)
  24  */
  25 #include <mpc8xx_irq.h>
  26
  27 #define CONFIG_MPC860           1
  28 #define CONFIG_MPC860T          1
  29 #define CONFIG_MBX              1
  30
  31 #define CONFIG_8xx_CPUCLOCK     40
  32 #define CONFIG_8xx_BUSCLOCK     (CONFIG_8xx_CPUCLOCK)
  33 #define TARGET_SYSTEM_FREQUENCY 40
  34
  35 #define CONFIG_8xx_CONS_SMC1    1       /* Console is on SMC1           */
  36 #undef  CONFIG_8xx_CONS_SMC2
  37 #define CONFIG_BAUDRATE         9600
  38
  39 #define MPC8XX_FACT     10                              /* Multiply by 10               */
  40 #define MPC8XX_XIN      40000000                /* 50 MHz in    */
  41 #define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT))
  42
  43 #define CONFIG_CLOCKS_IN_MHZ    1       /* clocks passsed to Linux in MHz */
  44
  45 #if 1
  46 #define CONFIG_8xx_BOOTDELAY    -1      /* autoboot disabled            */
  47 #define CONFIG_8xx_TFTP_MODE
  48 #else
  49 #define CONFIG_8xx_BOOTDELAY    5       /* autoboot after 5 seconds     */
  50 #undef  CONFIG_8xx_TFTP_MODE
  51 #endif
  52
  53 #define CONFIG_DRAM_SPEED       (CONFIG_8xx_BUSCLOCK)   /* MHz          */
  54 #define CONFIG_BOOTCOMMAND      "bootm FE020000"        /* autoboot command */
  55 #define CONFIG_BOOTARGS         " "
  56 /*
  57  * Miscellaneous configurable options
  58  */
  59 #undef  CONFIG_SYS_LONGHELP                     /* undef to save memory         */
  60 #define CONFIG_SYS_PROMPT               ":>"            /* Monitor Command Prompt       */
  61 #define CONFIG_SYS_CBSIZE               256             /* Console I/O Buffer Size      */
  62 #define CONFIG_SYS_PBSIZE               (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
  63 #define CONFIG_SYS_MAXARGS      16              /* max number of command args   */
  64 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size    */
  65
  66 #define CONFIG_SYS_MEMTEST_START        0x0400000       /* memtest works on     */
  67 #define CONFIG_SYS_MEMTEST_END          0x0800000       /* 4 ... 8 MB in DRAM   */
  68
  69 #define CONFIG_SYS_LOAD_ADDR            0x100000        /* default load address */
  70
  71 #define CONFIG_SYS_HZ           1000            /* decrementer freq: 1 ms ticks */
  72
  73 #define CONFIG_SYS_BAUDRATE_TABLE       { 9600, 19200, 38400, 57600, 115200 }
  74
  75 /*
  76  * Low Level Configuration Settings
  77  * (address mappings, register initial values, etc.)
  78  * You should know what you are doing if you make changes here.
  79  */
  80 /*-----------------------------------------------------------------------
  81  * Internal Memory Mapped Register
  82  */
  83 #define CONFIG_SYS_IMMR                 0xFFA00000
  84 #define CONFIG_SYS_IMMR_SIZE            ((uint)(64 * 1024))
  85 #define CONFIG_SYS_NVRAM_BASE           0xFA000000 /* NVRAM                          */
  86 #define CONFIG_SYS_NVRAM_OR             0xffe00000 /* w/o speed dependent flags!!    */
  87 #define CONFIG_SYS_CSR_BASE             0xFA100000 /* Control/Status Registers       */
  88 #define CONFIG_SYS_PCIMEM_BASE          0x80000000 /* PCI I/O and Memory Spaces      */
  89 #define CONFIG_SYS_PCIMEM_OR            0xA0000108
  90 #define CONFIG_SYS_PCIBRIDGE_BASE       0xFA210000 /* PCI-Bus Bridge Registers       */
  91 #define CONFIG_SYS_PCIBRIDGE_OR 0xFFFF0108
  92
  93 /*-----------------------------------------------------------------------
  94  * Definitions for initial stack pointer and data area (in DPRAM)
  95  */
  96 #define CONFIG_SYS_INIT_RAM_ADDR        CONFIG_SYS_IMMR
  97 #define CONFIG_SYS_INIT_RAM_END 0x2f00  /* End of used area in DPRAM    */
  98 #define CONFIG_SYS_GBL_DATA_SIZE        64  /* size in bytes reserved for initial data */
  99 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
 100 #define CONFIG_SYS_INIT_VPD_SIZE        256 /* size in bytes reserved for vpd buffer */
 101 #define CONFIG_SYS_INIT_VPD_OFFSET      (CONFIG_SYS_GBL_DATA_OFFSET - CONFIG_SYS_INIT_VPD_SIZE)
 102 #define CONFIG_SYS_INIT_SP_OFFSET       (CONFIG_SYS_INIT_VPD_OFFSET-8)
 103
 104 /*-----------------------------------------------------------------------
 105  * Offset in DPMEM where we keep the VPD data
 106  */
 107 #define CONFIG_SYS_DPRAMVPD             (CONFIG_SYS_INIT_VPD_OFFSET - 0x2000)
 108
 109 /*-----------------------------------------------------------------------
 110  * Start addresses for the final memory configuration
 111  * (Set up by the startup code)
 112  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 113  */
 114 #define CONFIG_SYS_SDRAM_BASE           0x00000000
 115 #define CONFIG_SYS_FLASH_BASE           0x00000000
 116 /*0xFE000000*/
 117 #define CONFIG_SYS_FLASH_SIZE           ((uint)(8 * 1024 * 1024))       /* max 8Mbyte */
 118 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
 119 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)     /* Reserve 256 kB for Monitor   */
 120 #define CONFIG_SYS_HWINFO_ADDR          (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN - CONFIG_SYS_HWINFO_LEN)
 121 #define CONFIG_SYS_MALLOC_LEN           (256 << 10)     /* Reserve 256 kB for malloc()  */
 122
 123 /*
 124  * For booting Linux, the board info and command line data
 125  * have to be in the first 8 MB of memory, since this is
 126  * the maximum mapped by the Linux kernel during initialization.
 127  */
 128 #define CONFIG_SYS_BOOTMAPSZ            (8 << 20)       /* Initial Memory map for Linux */
 129
 130 /*-----------------------------------------------------------------------
 131  * FLASH organization
 132  */
 133 #define CONFIG_SYS_MAX_FLASH_BANKS      4       /* max number of memory banks           */
 134 #define CONFIG_SYS_MAX_FLASH_SECT       16      /* max number of sectors on one chip    */
 135
 136 #define CONFIG_SYS_FLASH_ERASE_TOUT     120000  /* Timeout for Flash Erase (in ms)      */
 137 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Timeout for Flash Write (in ms)      */
 138
 139 /*-----------------------------------------------------------------------
 140  * NVRAM Configuration
 141  *
 142  * Note: the MBX is special because there is already a firmware on this
 143  * board: EPPC-Bug from Motorola. To avoid collisions in NVRAM Usage, we
 144  * access the NVRAM at the offset 0x1000.
 145  */
 146 #define CONFIG_ENV_IS_IN_NVRAM  1       /* turn on NVRAM env feature */
 147 #define CONFIG_ENV_ADDR         (CONFIG_SYS_NVRAM_BASE + 0x1000)
 148 #define CONFIG_ENV_SIZE         0x1000
 149
 150 /*-----------------------------------------------------------------------
 151  * Cache Configuration
 152  */
 153 #define CONFIG_SYS_CACHELINE_SIZE       16      /* For all MPC8xx CPUs                  */
 154 #if defined(CONFIG_CMD_KGDB)
 155 #define CONFIG_SYS_CACHELINE_SHIFT      4       /* log base 2 of the above value        */
 156 #endif
 157
 158 /*-----------------------------------------------------------------------
 159  * SYPCR - System Protection Control                            11-9
 160  * SYPCR can only be written once after reset!
 161  *-----------------------------------------------------------------------
 162  * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
 163  */
 164 #if defined(CONFIG_WATCHDOG)
 165 #define CONFIG_SYS_SYPCR        (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
 166                          SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
 167 #else
 168 #define CONFIG_SYS_SYPCR        (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF)
 169 #endif
 170
 171 /*-----------------------------------------------------------------------
 172  * SIUMCR - SIU Module Configuration                            11-6
 173  *-----------------------------------------------------------------------
 174  * PCMCIA config., multi-function pin tri-state
 175  */
 176 #define CONFIG_SYS_SIUMCR       (SIUMCR_DBGC11 | SIUMCR_DPC | SIUMCR_MLRC10 | SIUMCR_SEME)
 177
 178 /*-----------------------------------------------------------------------
 179  * TBSCR - Time Base Status and Control                         11-26
 180  *-----------------------------------------------------------------------
 181  * Clear Reference Interrupt Status, Timebase freezing enabled
 182  */
 183 #define CONFIG_SYS_TBSCR        (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
 184
 185 /*-----------------------------------------------------------------------
 186  * PISCR - Periodic Interrupt Status and Control                11-31
 187  *-----------------------------------------------------------------------
 188  * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
 189  */
 190 #define CONFIG_SYS_PISCR        (PISCR_PS | PISCR_PITF | PISCR_PTE)
 191
 192 /*-----------------------------------------------------------------------
 193  * PLPRCR - PLL, Low-Power, and Reset Control Register          15-30
 194  *-----------------------------------------------------------------------
 195  * Reset PLL lock status sticky bit, timer expired status bit and timer
 196  * interrupt status bit - leave PLL multiplication factor unchanged !
 197  */
 198 #define CONFIG_SYS_PLPRCR       (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
 199
 200 /*-----------------------------------------------------------------------
 201  * SCCR - System Clock and reset Control Register               15-27
 202  *-----------------------------------------------------------------------
 203  * Set clock output, timebase and RTC source and divider,
 204  * power management and some other internal clocks
 205  */
 206 #define SCCR_MASK       (SCCR_RTDIV | SCCR_RTSEL)
 207 #define CONFIG_SYS_SCCR SCCR_TBS
 208
 209  /*-----------------------------------------------------------------------
 210  *
 211  *-----------------------------------------------------------------------
 212  *
 213  */
 214 #define CONFIG_SYS_DER          0
 215
 216 /* Because of the way the 860 starts up and assigns CS0 the
 217 * entire address space, we have to set the memory controller
 218 * differently.  Normally, you write the option register
 219 * first, and then enable the chip select by writing the
 220 * base register.  For CS0, you must write the base register
 221 * first, followed by the option register.
 222 */
 223
 224 /*
 225  * Init Memory Controller:
 226  *
 227  * BR0/1 and OR0/1 (FLASH)
 228  */
 229 /* the other CS:s are determined by looking at parameters in BCSRx */
 230
 231
 232 #define BCSR_ADDR               ((uint) 0xFF010000)
 233 #define BCSR_SIZE               ((uint)(64 * 1024))
 234
 235 #define FLASH_BASE0_PRELIM      0xFE000000      /* FLASH bank #0        */
 236 #define FLASH_BASE1_PRELIM      0xFF010000      /* FLASH bank #0        */
 237
 238 #define CONFIG_SYS_REMAP_OR_AM          0x80000000      /* OR addr mask */
 239 #define CONFIG_SYS_PRELIM_OR_AM 0xFFF00000      /* OR addr mask */
 240
 241 /* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0        */
 242 #define CONFIG_SYS_OR_TIMING_FLASH      (OR_CSNT_SAM  | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX)
 243
 244 #define CONFIG_SYS_OR0_REMAP    (CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
 245 #define CONFIG_SYS_OR0_PRELIM   (0xFF800000 | OR_CSNT_SAM | OR_BI | OR_SCY_3_CLK)   /* 1 Mbyte until detected and only 1 Mbyte is needed*/
 246 #define CONFIG_SYS_BR0_PRELIM   (0xFE000000 | BR_V )
 247
 248 /* BCSRx - Board Control and Status Registers */
 249 #define CONFIG_SYS_OR1_REMAP    CONFIG_SYS_OR0_REMAP
 250 #define CONFIG_SYS_OR1_PRELIM   0xFFC00000 | OR_ACS_DIV4
 251 #define CONFIG_SYS_BR1_PRELIM   (0x00000000 | BR_MS_UPMA | BR_V )
 252
 253
 254 /*
 255  * Memory Periodic Timer Prescaler
 256  */
 257
 258 /* periodic timer for refresh */
 259 #define CONFIG_SYS_MAMR_PTA             97              /* start with divider for 100 MHz       */
 260
 261 /* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit     */
 262 #define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16         /* setting for 2 banks  */
 263 #define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32         /* setting for 1 bank   */
 264
 265 /* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit         */
 266 #define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8          /* setting for 2 banks  */
 267 #define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16         /* setting for 1 bank   */
 268
 269 /*
 270  * MAMR settings for SDRAM
 271  */
 272
 273 /* 8 column SDRAM */
 274 #define CONFIG_SYS_MAMR_8COL    ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE       |   \
 275                          MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |   \
 276                          MAMR_RLFA_1X    | MAMR_WLFA_1X    | MAMR_TLFA_4X)
 277 /* 9 column SDRAM */
 278 #define CONFIG_SYS_MAMR_9COL    ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE       |   \
 279                          MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |   \
 280                          MAMR_RLFA_1X    | MAMR_WLFA_1X    | MAMR_TLFA_4X)
 281
 282 #define CONFIG_SYS_MAMR         0x13821000
 283 /*
 284  * Internal Definitions
 285  *
 286  * Boot Flags
 287  */
 288 #define BOOTFLAG_COLD                   0x01            /* Normal Power-On: Boot from FLASH     */
 289 #define BOOTFLAG_WARM                   0x02            /* Software reboot                      */
 290
 291
 292 /* values according to the manual */
 293
 294
 295 #define PCMCIA_MEM_ADDR         ((uint)0xff020000)
 296 #define PCMCIA_MEM_SIZE         ((uint)(64 * 1024))
 297
 298 #define BCSR0                   ((uint) (BCSR_ADDR + 00))
 299 #define BCSR1                   ((uint) (BCSR_ADDR + 0x04))
 300 #define BCSR2                   ((uint) (BCSR_ADDR + 0x08))
 301 #define BCSR3                   ((uint) (BCSR_ADDR + 0x0c))
 302 #define BCSR4                   ((uint) (BCSR_ADDR + 0x10))
 303
 304 /* FADS bitvalues by Helmut Buchsbaum
 305  * see MPC8xxADS User's Manual for a proper description
 306  * of the following structures
 307  */
 308
 309 #define BCSR0_ERB       ((uint)0x80000000)
 310 #define BCSR0_IP        ((uint)0x40000000)
 311 #define BCSR0_BDIS      ((uint)0x10000000)
 312 #define BCSR0_BPS_MASK  ((uint)0x0C000000)
 313 #define BCSR0_ISB_MASK  ((uint)0x01800000)
 314 #define BCSR0_DBGC_MASK ((uint)0x00600000)
 315 #define BCSR0_DBPC_MASK ((uint)0x00180000)
 316 #define BCSR0_EBDF_MASK ((uint)0x00060000)
 317
 318 #define BCSR1_FLASH_EN           ((uint)0x80000000)
 319 #define BCSR1_DRAM_EN            ((uint)0x40000000)
 320 #define BCSR1_ETHEN              ((uint)0x20000000)
 321 #define BCSR1_IRDEN              ((uint)0x10000000)
 322 #define BCSR1_FLASH_CFG_EN       ((uint)0x08000000)
 323 #define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000)
 324 #define BCSR1_BCSR_EN            ((uint)0x02000000)
 325 #define BCSR1_RS232EN_1          ((uint)0x01000000)
 326 #define BCSR1_PCCEN              ((uint)0x00800000)
 327 #define BCSR1_PCCVCC0            ((uint)0x00400000)
 328 #define BCSR1_PCCVPP_MASK        ((uint)0x00300000)
 329 #define BCSR1_DRAM_HALF_WORD     ((uint)0x00080000)
 330 #define BCSR1_RS232EN_2          ((uint)0x00040000)
 331 #define BCSR1_SDRAM_EN           ((uint)0x00020000)
 332 #define BCSR1_PCCVCC1            ((uint)0x00010000)
 333
 334 #define BCSR2_FLASH_PD_MASK      ((uint)0xF0000000)
 335 #define BCSR2_DRAM_PD_MASK       ((uint)0x07800000)
 336 #define BCSR2_DRAM_PD_SHIFT      (23)
 337 #define BCSR2_EXTTOLI_MASK       ((uint)0x00780000)
 338 #define BCSR2_DBREVNR_MASK       ((uint)0x00030000)
 339
 340 #define BCSR3_DBID_MASK          ((ushort)0x3800)
 341 #define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400)
 342 #define BCSR3_BREVNR0            ((ushort)0x0080)
 343 #define BCSR3_FLASH_PD_MASK      ((ushort)0x0070)
 344 #define BCSR3_BREVN1             ((ushort)0x0008)
 345 #define BCSR3_BREVN2_MASK        ((ushort)0x0003)
 346
 347 #define BCSR4_ETHLOOP            ((uint)0x80000000)
 348 #define BCSR4_TFPLDL             ((uint)0x40000000)
 349 #define BCSR4_TPSQEL             ((uint)0x20000000)
 350 #define BCSR4_SIGNAL_LAMP        ((uint)0x10000000)
 351 #ifdef CONFIG_MPC823
 352 #define BCSR4_USB_EN             ((uint)0x08000000)
 353 #endif /* CONFIG_MPC823 */
 354 #ifdef CONFIG_MPC860SAR
 355 #define BCSR4_UTOPIA_EN          ((uint)0x08000000)
 356 #endif /* CONFIG_MPC860SAR */
 357 #ifdef CONFIG_MPC860T
 358 #define BCSR4_FETH_EN            ((uint)0x08000000)
 359 #endif /* CONFIG_MPC860T */
 360 #define BCSR4_USB_SPEED          ((uint)0x04000000)
 361 #define BCSR4_VCCO               ((uint)0x02000000)
 362 #define BCSR4_VIDEO_ON           ((uint)0x00800000)
 363 #define BCSR4_VDO_EKT_CLK_EN     ((uint)0x00400000)
 364 #define BCSR4_VIDEO_RST          ((uint)0x00200000)
 365 #define BCSR4_MODEM_EN           ((uint)0x00100000)
 366 #define BCSR4_DATA_VOICE         ((uint)0x00080000)
 367
 368 #define CONFIG_DRAM_40MHZ               1
 369
 370 #ifdef CONFIG_MPC860T
 371
 372 /* Interrupt level assignments.
 373 */
 374 #define FEC_INTERRUPT   SIU_LEVEL1      /* FEC interrupt */
 375
 376 #endif /* CONFIG_MPC860T */
 377
 378 /* We don't use the 8259.
 379 */
 380 #define NR_8259_INTS    0
 381
 382 /*
 383  * MPC8xx CPM Options
 384  */
 385 #define CONFIG_SCC_ENET 1
 386 #define CONFIG_SCC1_ENET 1
 387 #define CONFIG_FEC_ENET 1
 388 #undef  CONFIG_CPM_IIC
 389 #undef  CONFIG_UCODE_PATCH
 390
 391
 392 #define CONFIG_DISK_SPINUP_TIME 1000000
 393
 394
 395 /* PCMCIA configuration */
 396
 397 #define PCMCIA_MAX_SLOTS    2
 398
 399 #ifdef CONFIG_MPC860
 400 #define PCMCIA_SLOT_A 1
 401 #endif
 402
 403 #endif  /* __CONFIG_H */