include/configs/MPC8360ERDK.h

   1 /*
   2  * Copyright (C) 2006 Freescale Semiconductor, Inc.
   3  *                    Dave Liu <daveliu@freescale.com>
   4  *
   5  * Copyright (C) 2007 Logic Product Development, Inc.
   6  *                    Peter Barada <peterb@logicpd.com>
   7  *
   8  * Copyright (C) 2007 MontaVista Software, Inc.
   9  *                    Anton Vorontsov <avorontsov@ru.mvista.com>
  10  *
  11  * This program is free software; you can redistribute it and/or
  12  * modify it under the terms of the GNU General Public License as
  13  * published by the Free Software Foundation; either version 2 of
  14  * the License, or (at your option) any later version.
  15  */
  16
  17 #ifndef __CONFIG_H
  18 #define __CONFIG_H
  19
  20 /*
  21  * High Level Configuration Options
  22  */
  23 #define CONFIG_E300             1 /* E300 family */
  24 #define CONFIG_QE               1 /* Has QE */
  25 #define CONFIG_MPC83xx          1 /* MPC83xx family */
  26 #define CONFIG_MPC8360          1 /* MPC8360 CPU specific */
  27 #define CONFIG_MPC8360ERDK      1 /* MPC8360ERDK board specific */
  28
  29 #define CONFIG_SYS_TEXT_BASE    0xFF800000
  30
  31 /*
  32  * System Clock Setup
  33  */
  34 #ifdef CONFIG_CLKIN_33MHZ
  35 #define CONFIG_83XX_CLKIN               33333333
  36 #define CONFIG_SYS_CLK_FREQ             33333333
  37 #define CONFIG_PCI_33M                          1
  38 #define HRCWL_CSB_TO_CLKIN_MPC8360ERDK  HRCWL_CSB_TO_CLKIN_10X1
  39 #else
  40 #define CONFIG_83XX_CLKIN               66000000
  41 #define CONFIG_SYS_CLK_FREQ             66000000
  42 #define CONFIG_PCI_66M                          1
  43 #define HRCWL_CSB_TO_CLKIN_MPC8360ERDK  HRCWL_CSB_TO_CLKIN_5X1
  44 #endif /* CONFIG_CLKIN_33MHZ */
  45
  46 /*
  47  * Hardware Reset Configuration Word
  48  */
  49 #define CONFIG_SYS_HRCW_LOW (\
  50         HRCWL_LCL_BUS_TO_SCB_CLK_1X1 |\
  51         HRCWL_DDR_TO_SCB_CLK_1X1 |\
  52         HRCWL_CSB_TO_CLKIN_MPC8360ERDK |\
  53         HRCWL_CORE_TO_CSB_2X1 |\
  54         HRCWL_CE_TO_PLL_1X15)
  55
  56 #define CONFIG_SYS_HRCW_HIGH (\
  57         HRCWH_PCI_HOST |\
  58         HRCWH_PCI1_ARBITER_ENABLE |\
  59         HRCWH_PCICKDRV_ENABLE |\
  60         HRCWH_CORE_ENABLE |\
  61         HRCWH_FROM_0X00000100 |\
  62         HRCWH_BOOTSEQ_DISABLE |\
  63         HRCWH_SW_WATCHDOG_DISABLE |\
  64         HRCWH_ROM_LOC_LOCAL_16BIT |\
  65         HRCWH_SECONDARY_DDR_DISABLE |\
  66         HRCWH_BIG_ENDIAN |\
  67         HRCWH_LALE_EARLY)
  68
  69 /*
  70  * System IO Config
  71  */
  72 #define CONFIG_SYS_SICRH                0x00000000
  73 #define CONFIG_SYS_SICRL                0x40000000
  74
  75 #define CONFIG_BOARD_EARLY_INIT_F /* call board_pre_init */
  76 #define CONFIG_BOARD_EARLY_INIT_R
  77
  78 /*
  79  * IMMR new address
  80  */
  81 #define CONFIG_SYS_IMMR         0xE0000000
  82
  83 /*
  84  * DDR Setup
  85  */
  86 #define CONFIG_SYS_DDR_BASE             0x00000000 /* DDR is system memory */
  87 #define CONFIG_SYS_SDRAM_BASE           CONFIG_SYS_DDR_BASE
  88 #define CONFIG_SYS_DDR_SDRAM_BASE       CONFIG_SYS_DDR_BASE
  89 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL   (DDR_SDRAM_CLK_CNTL_SS_EN | \
  90                                 DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
  91
  92 #define CONFIG_SYS_83XX_DDR_USES_CS0
  93
  94 #define CONFIG_DDR_ECC          /* support DDR ECC function */
  95 #define CONFIG_DDR_ECC_CMD      /* Use DDR ECC user commands */
  96
  97 /*
  98  * DDRCDR - DDR Control Driver Register
  99  */
 100 #define CONFIG_SYS_DDRCDR_VALUE 0x80080001
 101
 102 #undef CONFIG_SPD_EEPROM        /* Do not use SPD EEPROM for DDR setup */
 103
 104 /*
 105  * Manually set up DDR parameters
 106  */
 107 #define CONFIG_DDR_II
 108 #define CONFIG_SYS_DDR_SIZE             256 /* MB */
 109 #define CONFIG_SYS_DDR_CS0_BNDS 0x0000000f
 110 #define CONFIG_SYS_DDR_CS0_CONFIG       (CSCONFIG_EN | CSCONFIG_ROW_BIT_13 | \
 111                                  CSCONFIG_COL_BIT_10 | CSCONFIG_ODT_WR_ACS)
 112 #define CONFIG_SYS_DDR_SDRAM_CFG        (SDRAM_CFG_SDRAM_TYPE_DDR2 | SDRAM_CFG_ECC_EN)
 113 #define CONFIG_SYS_DDR_SDRAM_CFG2       0x00001000
 114 #define CONFIG_SYS_DDR_CLK_CNTL (DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05)
 115 #define CONFIG_SYS_DDR_INTERVAL ((256 << SDRAM_INTERVAL_BSTOPRE_SHIFT) | \
 116                                  (1115 << SDRAM_INTERVAL_REFINT_SHIFT))
 117 #define CONFIG_SYS_DDR_MODE             0x47800432
 118 #define CONFIG_SYS_DDR_MODE2            0x8000c000
 119
 120 #define CONFIG_SYS_DDR_TIMING_0 ((2 << TIMING_CFG0_MRS_CYC_SHIFT) | \
 121                                  (9 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
 122                                  (3 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
 123                                  (3 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
 124                                  (0 << TIMING_CFG0_WWT_SHIFT) | \
 125                                  (0 << TIMING_CFG0_RRT_SHIFT) | \
 126                                  (0 << TIMING_CFG0_WRT_SHIFT) | \
 127                                  (0 << TIMING_CFG0_RWT_SHIFT))
 128
 129 #define CONFIG_SYS_DDR_TIMING_1 ((      TIMING_CFG1_CASLAT_30) | \
 130                                  ( 2 << TIMING_CFG1_WRTORD_SHIFT) | \
 131                                  ( 2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
 132                                  ( 3 << TIMING_CFG1_WRREC_SHIFT) | \
 133                                  (10 << TIMING_CFG1_REFREC_SHIFT) | \
 134                                  ( 3 << TIMING_CFG1_ACTTORW_SHIFT) | \
 135                                  ( 8 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
 136                                  ( 3 << TIMING_CFG1_PRETOACT_SHIFT))
 137
 138 #define CONFIG_SYS_DDR_TIMING_2 ((9 << TIMING_CFG2_FOUR_ACT_SHIFT) | \
 139                                  (4 << TIMING_CFG2_CKE_PLS_SHIFT) | \
 140                                  (2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
 141                                  (2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
 142                                  (2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
 143                                  (0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
 144                                  (0 << TIMING_CFG2_CPO_SHIFT))
 145
 146 #define CONFIG_SYS_DDR_TIMING_3 0x00000000
 147
 148 /*
 149  * Memory test
 150  */
 151 #undef CONFIG_SYS_DRAM_TEST             /* memory test, takes time */
 152 #define CONFIG_SYS_MEMTEST_START        0x00000000 /* memtest region */
 153 #define CONFIG_SYS_MEMTEST_END          0x00100000
 154
 155 /*
 156  * The reserved memory
 157  */
 158 #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */
 159 #define CONFIG_SYS_FLASH_BASE           0xFF800000 /* FLASH base address */
 160
 161 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 162 #define CONFIG_SYS_RAMBOOT
 163 #else
 164 #undef  CONFIG_SYS_RAMBOOT
 165 #endif
 166
 167 #define CONFIG_SYS_MONITOR_LEN          (384 * 1024) /* Reserve 384 kB for Mon */
 168 #define CONFIG_SYS_MALLOC_LEN           (128 * 1024) /* Reserved for malloc */
 169
 170 /*
 171  * Initial RAM Base Address Setup
 172  */
 173 #define CONFIG_SYS_INIT_RAM_LOCK        1
 174 #define CONFIG_SYS_INIT_RAM_ADDR        0xE6000000 /* Initial RAM address */
 175 #define CONFIG_SYS_INIT_RAM_SIZE        0x1000 /* Size of used area in RAM */
 176 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 177
 178 /*
 179  * Local Bus Configuration & Clock Setup
 180  */
 181 #define CONFIG_SYS_LCRR_DBYP    LCRR_DBYP
 182 #define CONFIG_SYS_LCRR_CLKDIV  LCRR_CLKDIV_4
 183 #define CONFIG_SYS_LBC_LBCR             0x00000000
 184
 185 /*
 186  * FLASH on the Local Bus
 187  */
 188 #define CONFIG_SYS_FLASH_CFI            /* use the Common Flash Interface */
 189 #define CONFIG_FLASH_CFI_DRIVER /* use the CFI driver */
 190 #define CONFIG_SYS_FLASH_SIZE           8 /* max FLASH size is 32M */
 191 #define CONFIG_SYS_FLASH_PROTECTION     1 /* Use intel Flash protection. */
 192
 193 #define CONFIG_SYS_LBLAWBAR0_PRELIM     CONFIG_SYS_FLASH_BASE /* Window base at flash base */
 194 #define CONFIG_SYS_LBLAWAR0_PRELIM      0x80000018 /* 32MB window size */
 195
 196 #define CONFIG_SYS_BR0_PRELIM   (CONFIG_SYS_FLASH_BASE | /* Flash Base address */ \
 197                         (2 << BR_PS_SHIFT) | /* 16 bit port size */ \
 198                         BR_V)   /* valid */
 199 #define CONFIG_SYS_OR0_PRELIM           ((~(CONFIG_SYS_FLASH_SIZE - 1) << 20) | OR_UPM_XAM | \
 200                                 OR_GPCM_CSNT | OR_GPCM_ACS_DIV2 | \
 201                                 OR_GPCM_XACS | OR_GPCM_SCY_15 | \
 202                                 OR_GPCM_TRLX | OR_GPCM_EHTR | OR_GPCM_EAD)
 203
 204 #define CONFIG_SYS_MAX_FLASH_BANKS      1 /* number of banks */
 205 #define CONFIG_SYS_MAX_FLASH_SECT       256 /* max sectors per device */
 206
 207 #undef  CONFIG_SYS_FLASH_CHECKSUM
 208
 209 /*
 210  * NAND flash on the local bus
 211  */
 212 #define CONFIG_SYS_NAND_BASE            0x60000000
 213 #define CONFIG_CMD_NAND         1
 214 #define CONFIG_NAND_FSL_UPM     1
 215 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 216 #define CONFIG_MTD_NAND_VERIFY_WRITE
 217
 218 #define CONFIG_SYS_LBLAWBAR1_PRELIM     CONFIG_SYS_NAND_BASE
 219 #define CONFIG_SYS_LBLAWAR1_PRELIM      0x8000001b /* Access window size 4K */
 220
 221 /* Port size 8 bit, UPMA */
 222 #define CONFIG_SYS_BR1_PRELIM           (CONFIG_SYS_NAND_BASE | 0x00000881)
 223 #define CONFIG_SYS_OR1_PRELIM           0xfc000001
 224
 225 /*
 226  * Fujitsu MB86277 (MINT) graphics controller
 227  */
 228 #define CONFIG_SYS_VIDEO_BASE           0x70000000
 229
 230 #define CONFIG_SYS_LBLAWBAR2_PRELIM     CONFIG_SYS_VIDEO_BASE
 231 #define CONFIG_SYS_LBLAWAR2_PRELIM      0x80000019 /* Access window size 64MB */
 232
 233 /* Port size 32 bit, UPMB */
 234 #define CONFIG_SYS_BR2_PRELIM           (CONFIG_SYS_VIDEO_BASE | 0x000018a1) /* PS=11, UPMB */
 235 #define CONFIG_SYS_OR2_PRELIM           0xfc000001 /* (64MB, EAD=1) */
 236
 237 /*
 238  * Serial Port
 239  */
 240 #define CONFIG_CONS_INDEX       1
 241 #define CONFIG_SYS_NS16550
 242 #define CONFIG_SYS_NS16550_SERIAL
 243 #define CONFIG_SYS_NS16550_REG_SIZE     1
 244 #define CONFIG_SYS_NS16550_CLK          get_bus_freq(0)
 245
 246 #define CONFIG_SYS_BAUDRATE_TABLE  \
 247         {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200,}
 248
 249 #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
 250 #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)
 251
 252 #define CONFIG_CMDLINE_EDITING  1       /* add command line history */
 253 #define CONFIG_AUTO_COMPLETE            /* add autocompletion support   */
 254 /* Use the HUSH parser */
 255 #define CONFIG_SYS_HUSH_PARSER
 256 #ifdef  CONFIG_SYS_HUSH_PARSER
 257 #define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
 258 #endif
 259
 260 /* Pass open firmware flat tree */
 261 #define CONFIG_OF_LIBFDT        1
 262 #define CONFIG_OF_BOARD_SETUP   1
 263 #define CONFIG_OF_STDOUT_VIA_ALIAS
 264
 265 /* I2C */
 266 #define CONFIG_HARD_I2C         /* I2C with hardware support */
 267 #undef  CONFIG_SOFT_I2C         /* I2C bit-banged */
 268 #define CONFIG_FSL_I2C
 269 #define CONFIG_I2C_MULTI_BUS
 270 #define CONFIG_SYS_I2C_SPEED    400000  /* I2C speed and slave address */
 271 #define CONFIG_SYS_I2C_SLAVE    0x7F
 272 #define CONFIG_SYS_I2C_NOPROBES {{0x52}} /* Don't probe these addrs */
 273 #define CONFIG_SYS_I2C_OFFSET   0x3000
 274 #define CONFIG_SYS_I2C2_OFFSET 0x3100
 275
 276 /*
 277  * General PCI
 278  * Addresses are mapped 1-1.
 279  */
 280 #define CONFIG_PCI
 281
 282 #define CONFIG_SYS_PCI1_MEM_BASE        0x80000000
 283 #define CONFIG_SYS_PCI1_MEM_PHYS        CONFIG_SYS_PCI1_MEM_BASE
 284 #define CONFIG_SYS_PCI1_MEM_SIZE        0x10000000 /* 256M */
 285 #define CONFIG_SYS_PCI1_MMIO_BASE       0x90000000
 286 #define CONFIG_SYS_PCI1_MMIO_PHYS       CONFIG_SYS_PCI1_MMIO_BASE
 287 #define CONFIG_SYS_PCI1_MMIO_SIZE       0x10000000 /* 256M */
 288 #define CONFIG_SYS_PCI1_IO_BASE 0xE0300000
 289 #define CONFIG_SYS_PCI1_IO_PHYS 0xE0300000
 290 #define CONFIG_SYS_PCI1_IO_SIZE 0x100000 /* 1M */
 291
 292 #ifdef CONFIG_PCI
 293
 294 #define CONFIG_NET_MULTI
 295 #define CONFIG_PCI_PNP          /* do pci plug-and-play */
 296
 297 #undef CONFIG_EEPRO100
 298 #undef CONFIG_PCI_SCAN_SHOW     /* show pci devices on startup */
 299 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1957   /* Freescale */
 300
 301 #endif  /* CONFIG_PCI */
 302
 303
 304 #ifndef CONFIG_NET_MULTI
 305 #define CONFIG_NET_MULTI        1
 306 #endif
 307
 308 /*
 309  * QE UEC ethernet configuration
 310  */
 311 #define CONFIG_UEC_ETH
 312 #define CONFIG_ETHPRIME         "UEC0"
 313
 314 #define CONFIG_UEC_ETH1         /* GETH1 */
 315
 316 #ifdef CONFIG_UEC_ETH1
 317 #define CONFIG_SYS_UEC1_UCC_NUM 0       /* UCC1 */
 318 #define CONFIG_SYS_UEC1_RX_CLK          QE_CLK_NONE
 319 #define CONFIG_SYS_UEC1_TX_CLK          QE_CLK9
 320 #define CONFIG_SYS_UEC1_ETH_TYPE        GIGA_ETH
 321 #define CONFIG_SYS_UEC1_PHY_ADDR        2
 322 #define CONFIG_SYS_UEC1_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_RXID
 323 #define CONFIG_SYS_UEC1_INTERFACE_SPEED 1000
 324 #endif
 325
 326 #define CONFIG_UEC_ETH2         /* GETH2 */
 327
 328 #ifdef CONFIG_UEC_ETH2
 329 #define CONFIG_SYS_UEC2_UCC_NUM 1       /* UCC2 */
 330 #define CONFIG_SYS_UEC2_RX_CLK          QE_CLK_NONE
 331 #define CONFIG_SYS_UEC2_TX_CLK          QE_CLK4
 332 #define CONFIG_SYS_UEC2_ETH_TYPE        GIGA_ETH
 333 #define CONFIG_SYS_UEC2_PHY_ADDR        4
 334 #define CONFIG_SYS_UEC2_INTERFACE_TYPE PHY_INTERFACE_MODE_RGMII_RXID
 335 #define CONFIG_SYS_UEC2_INTERFACE_SPEED 1000
 336 #endif
 337
 338 /*
 339  * Environment
 340  */
 341
 342 #ifndef CONFIG_SYS_RAMBOOT
 343 #define CONFIG_ENV_IS_IN_FLASH  1
 344 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
 345 #define CONFIG_ENV_SECT_SIZE    0x20000 /* 128K(one sector) for env */
 346 #define CONFIG_ENV_SIZE         0x20000
 347 #else /* CONFIG_SYS_RAMBOOT */
 348 #define CONFIG_SYS_NO_FLASH             1       /* Flash is not usable now */
 349 #define CONFIG_ENV_IS_NOWHERE   1       /* Store ENV in memory only */
 350 #define CONFIG_ENV_ADDR         (CONFIG_SYS_MONITOR_BASE - 0x1000)
 351 #define CONFIG_ENV_SIZE         0x2000
 352 #endif /* CONFIG_SYS_RAMBOOT */
 353
 354 #define CONFIG_LOADS_ECHO       1       /* echo on for serial download */
 355 #define CONFIG_SYS_LOADS_BAUD_CHANGE    1       /* allow baudrate change */
 356
 357 /*
 358  * BOOTP options
 359  */
 360 #define CONFIG_BOOTP_BOOTFILESIZE
 361 #define CONFIG_BOOTP_BOOTPATH
 362 #define CONFIG_BOOTP_GATEWAY
 363 #define CONFIG_BOOTP_HOSTNAME
 364
 365
 366 /*
 367  * Command line configuration.
 368  */
 369 #include <config_cmd_default.h>
 370
 371 #define CONFIG_CMD_PING
 372 #define CONFIG_CMD_I2C
 373 #define CONFIG_CMD_ASKENV
 374 #define CONFIG_CMD_DHCP
 375
 376 #if defined(CONFIG_PCI)
 377 #define CONFIG_CMD_PCI
 378 #endif
 379
 380 #if defined(CONFIG_SYS_RAMBOOT)
 381 #undef CONFIG_CMD_SAVEENV
 382 #undef CONFIG_CMD_LOADS
 383 #endif
 384
 385 #undef CONFIG_WATCHDOG          /* watchdog disabled */
 386
 387 /*
 388  * Miscellaneous configurable options
 389  */
 390 #define CONFIG_SYS_LONGHELP             /* undef to save memory */
 391 #define CONFIG_SYS_LOAD_ADDR            0x2000000 /* default load address */
 392 #define CONFIG_SYS_PROMPT               "=> "   /* Monitor Command Prompt */
 393
 394 #if defined(CONFIG_CMD_KGDB)
 395         #define CONFIG_SYS_CBSIZE       1024 /* Console I/O Buffer Size */
 396 #else
 397         #define CONFIG_SYS_CBSIZE       256 /* Console I/O Buffer Size */
 398 #endif
 399
 400 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 401 #define CONFIG_SYS_MAXARGS      16              /* max number of command args */
 402 #define CONFIG_SYS_BARGSIZE     CONFIG_SYS_CBSIZE       /* Boot Argument Buffer Size */
 403 #define CONFIG_SYS_HZ           1000            /* decrementer freq: 1ms ticks */
 404
 405 /*
 406  * For booting Linux, the board info and command line data
 407  * have to be in the first 256 MB of memory, since this is
 408  * the maximum mapped by the Linux kernel during initialization.
 409  */
 410 #define CONFIG_SYS_BOOTMAPSZ            (256 << 20) /* Initial Memory map for Linux */
 411
 412 /*
 413  * Core HID Setup
 414  */
 415 #define CONFIG_SYS_HID0_INIT    0x000000000
 416 #define CONFIG_SYS_HID0_FINAL   (HID0_ENABLE_MACHINE_CHECK | \
 417                                  HID0_ENABLE_INSTRUCTION_CACHE)
 418 #define CONFIG_SYS_HID2         HID2_HBE
 419
 420 /*
 421  * MMU Setup
 422  */
 423
 424 #define CONFIG_HIGH_BATS        1       /* High BATs supported */
 425
 426 /* DDR: cache cacheable */
 427 #define CONFIG_SYS_IBAT0L       (CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
 428 #define CONFIG_SYS_IBAT0U       (CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
 429 #define CONFIG_SYS_DBAT0L       CONFIG_SYS_IBAT0L
 430 #define CONFIG_SYS_DBAT0U       CONFIG_SYS_IBAT0U
 431
 432 /* IMMRBAR & PCI IO: cache-inhibit and guarded */
 433 #define CONFIG_SYS_IBAT1L       (CONFIG_SYS_IMMR | BATL_PP_10 | \
 434                         BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 435 #define CONFIG_SYS_IBAT1U       (CONFIG_SYS_IMMR | BATU_BL_4M | BATU_VS | BATU_VP)
 436 #define CONFIG_SYS_DBAT1L       CONFIG_SYS_IBAT1L
 437 #define CONFIG_SYS_DBAT1U       CONFIG_SYS_IBAT1U
 438
 439 /* NAND: cache-inhibit and guarded */
 440 #define CONFIG_SYS_IBAT2L       (CONFIG_SYS_NAND_BASE | BATL_PP_10 | BATL_CACHEINHIBIT |\
 441                          BATL_GUARDEDSTORAGE)
 442 #define CONFIG_SYS_IBAT2U       (CONFIG_SYS_NAND_BASE | BATU_BL_64M | BATU_VS | BATU_VP)
 443 #define CONFIG_SYS_DBAT2L       CONFIG_SYS_IBAT2L
 444 #define CONFIG_SYS_DBAT2U       CONFIG_SYS_IBAT2U
 445
 446 /* FLASH: icache cacheable, but dcache-inhibit and guarded */
 447 #define CONFIG_SYS_IBAT3L       (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
 448 #define CONFIG_SYS_IBAT3U       (CONFIG_SYS_FLASH_BASE | BATU_BL_32M | BATU_VS | BATU_VP)
 449 #define CONFIG_SYS_DBAT3L       (CONFIG_SYS_FLASH_BASE | BATL_PP_10 | \
 450                          BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 451 #define CONFIG_SYS_DBAT3U       CONFIG_SYS_IBAT3U
 452
 453 /* Stack in dcache: cacheable, no memory coherence */
 454 #define CONFIG_SYS_IBAT4L       (CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10)
 455 #define CONFIG_SYS_IBAT4U       (CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
 456 #define CONFIG_SYS_DBAT4L       CONFIG_SYS_IBAT4L
 457 #define CONFIG_SYS_DBAT4U       CONFIG_SYS_IBAT4U
 458
 459 #define CONFIG_SYS_IBAT5L       (CONFIG_SYS_VIDEO_BASE | BATL_PP_10 | BATL_CACHEINHIBIT | \
 460                          BATL_GUARDEDSTORAGE)
 461 #define CONFIG_SYS_IBAT5U       (CONFIG_SYS_VIDEO_BASE | BATU_BL_64M | BATU_VS | BATU_VP)
 462 #define CONFIG_SYS_DBAT5L       CONFIG_SYS_IBAT5L
 463 #define CONFIG_SYS_DBAT5U       CONFIG_SYS_IBAT5U
 464
 465 #ifdef CONFIG_PCI
 466 /* PCI MEM space: cacheable */
 467 #define CONFIG_SYS_IBAT6L       (CONFIG_SYS_PCI1_MEM_PHYS | BATL_PP_10 | BATL_MEMCOHERENCE)
 468 #define CONFIG_SYS_IBAT6U       (CONFIG_SYS_PCI1_MEM_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
 469 #define CONFIG_SYS_DBAT6L       CONFIG_SYS_IBAT6L
 470 #define CONFIG_SYS_DBAT6U       CONFIG_SYS_IBAT6U
 471 /* PCI MMIO space: cache-inhibit and guarded */
 472 #define CONFIG_SYS_IBAT7L       (CONFIG_SYS_PCI1_MMIO_PHYS | BATL_PP_10 | \
 473                          BATL_CACHEINHIBIT | BATL_GUARDEDSTORAGE)
 474 #define CONFIG_SYS_IBAT7U       (CONFIG_SYS_PCI1_MMIO_PHYS | BATU_BL_256M | BATU_VS | BATU_VP)
 475 #define CONFIG_SYS_DBAT7L       CONFIG_SYS_IBAT7L
 476 #define CONFIG_SYS_DBAT7U       CONFIG_SYS_IBAT7U
 477 #else /* CONFIG_PCI */
 478 #define CONFIG_SYS_IBAT6L       (0)
 479 #define CONFIG_SYS_IBAT6U       (0)
 480 #define CONFIG_SYS_IBAT7L       (0)
 481 #define CONFIG_SYS_IBAT7U       (0)
 482 #define CONFIG_SYS_DBAT6L       CONFIG_SYS_IBAT6L
 483 #define CONFIG_SYS_DBAT6U       CONFIG_SYS_IBAT6U
 484 #define CONFIG_SYS_DBAT7L       CONFIG_SYS_IBAT7L
 485 #define CONFIG_SYS_DBAT7U       CONFIG_SYS_IBAT7U
 486 #endif /* CONFIG_PCI */
 487
 488 #if defined(CONFIG_CMD_KGDB)
 489 #define CONFIG_KGDB_BAUDRATE    230400  /* speed of kgdb serial port */
 490 #define CONFIG_KGDB_SER_INDEX   2       /* which serial port to use */
 491 #endif
 492
 493 /*
 494  * Environment Configuration
 495  */
 496 #define CONFIG_ENV_OVERWRITE
 497
 498 #if defined(CONFIG_UEC_ETH)
 499 #define CONFIG_HAS_ETH0
 500 #define CONFIG_HAS_ETH1
 501 #define CONFIG_HAS_ETH2
 502 #define CONFIG_HAS_ETH3
 503 #endif
 504
 505 #define CONFIG_BAUDRATE 115200
 506
 507 #define CONFIG_LOADADDR a00000
 508 #define CONFIG_HOSTNAME mpc8360erdk
 509 #define CONFIG_BOOTFILE uImage
 510
 511 #define CONFIG_ROOTPATH         /nfsroot/
 512
 513 #define CONFIG_BOOTDELAY 2      /* -1 disables auto-boot */
 514 #undef  CONFIG_BOOTARGS         /* the boot command will set bootargs */
 515
 516 #define CONFIG_EXTRA_ENV_SETTINGS \
 517    "netdev=eth0\0"\
 518    "consoledev=ttyS0\0"\
 519    "loadaddr=a00000\0"\
 520    "fdtaddr=900000\0"\
 521    "fdtfile=mpc836x_rdk.dtb\0"\
 522    "fsfile=fs\0"\
 523    "ubootfile=u-boot.bin\0"\
 524    "mtdparts=mtdparts=60000000.nand-flash:4096k(kernel),128k(dtb),-(rootfs)\0"\
 525    "setbootargs=setenv bootargs console=$consoledev,$baudrate "\
 526                 "$mtdparts panic=1\0"\
 527    "adddhcpargs=setenv bootargs $bootargs ip=on\0"\
 528    "addnfsargs=setenv bootargs $bootargs ip=$ipaddr:$serverip:"\
 529                 "$gatewayip:$netmask:$hostname:$netdev:off "\
 530                 "root=/dev/nfs rw nfsroot=$serverip:$rootpath\0"\
 531    "addnandargs=setenv bootargs $bootargs root=/dev/mtdblock3 "\
 532                 "rootfstype=jffs2 rw\0"\
 533    "tftp_get_uboot=tftp 100000 $ubootfile\0"\
 534    "tftp_get_kernel=tftp $loadaddr $bootfile\0"\
 535    "tftp_get_dtb=tftp $fdtaddr $fdtfile\0"\
 536    "tftp_get_fs=tftp c00000 $fsfile\0"\
 537    "nand_erase_kernel=nand erase 0 400000\0"\
 538    "nand_erase_dtb=nand erase 400000 20000\0"\
 539    "nand_erase_fs=nand erase 420000 3be0000\0"\
 540    "nand_write_kernel=nand write.jffs2 $loadaddr 0 400000\0"\
 541    "nand_write_dtb=nand write.jffs2 $fdtaddr 400000 20000\0"\
 542    "nand_write_fs=nand write.jffs2 c00000 420000 $filesize\0"\
 543    "nand_read_kernel=nand read.jffs2 $loadaddr 0 400000\0"\
 544    "nand_read_dtb=nand read.jffs2 $fdtaddr 400000 20000\0"\
 545    "nor_reflash=protect off ff800000 ff87ffff ; erase ff800000 ff87ffff ; "\
 546                 "cp.b 100000 ff800000 $filesize\0"\
 547    "nand_reflash_kernel=run tftp_get_kernel nand_erase_kernel "\
 548                 "nand_write_kernel\0"\
 549    "nand_reflash_dtb=run tftp_get_dtb nand_erase_dtb nand_write_dtb\0"\
 550    "nand_reflash_fs=run tftp_get_fs nand_erase_fs nand_write_fs\0"\
 551    "nand_reflash=run nand_reflash_kernel nand_reflash_dtb "\
 552                 "nand_reflash_fs\0"\
 553    "boot_m=bootm $loadaddr - $fdtaddr\0"\
 554    "dhcpboot=dhcp ; run setbootargs adddhcpargs tftp_get_dtb boot_m\0"\
 555    "nfsboot=run setbootargs addnfsargs tftp_get_kernel tftp_get_dtb "\
 556                 "boot_m\0"\
 557    "nandboot=run setbootargs addnandargs nand_read_kernel nand_read_dtb "\
 558                 "boot_m\0"\
 559    ""
 560
 561 #define CONFIG_BOOTCOMMAND "run dhcpboot"
 562
 563 #endif /* __CONFIG_H */