include/configs/astro_mcf5373l.h

   1 /*
   2  * Configuration settings for the Sentec Cobra Board.
   3  *
   4  * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
   5  *
   6  * SPDX-License-Identifier:     GPL-2.0+
   7  */
   8
   9 /*
  10  * configuration for ASTRO "Urmel" board.
  11  * Originating from Cobra5272 configuration, messed up by
  12  * Wolfgang Wegner <w.wegner@astro-kom.de>
  13  * Please do not bother the original author with bug reports
  14  * concerning this file.
  15  */
  16
  17 #ifndef _CONFIG_ASTRO_MCF5373L_H
  18 #define _CONFIG_ASTRO_MCF5373L_H
  19
  20 #include <linux/stringify.h>
  21
  22 /*
  23  * set the card type to actually compile for; either of
  24  * the possibilities listed below has to be used!
  25  */
  26 #define CONFIG_ASTRO_V532       1
  27
  28 #if CONFIG_ASTRO_V532
  29 #define ASTRO_ID        0xF8
  30 #elif CONFIG_ASTRO_V512
  31 #define ASTRO_ID        0xFA
  32 #elif CONFIG_ASTRO_TWIN7S2
  33 #define ASTRO_ID        0xF9
  34 #elif CONFIG_ASTRO_V912
  35 #define ASTRO_ID        0xFC
  36 #elif CONFIG_ASTRO_COFDMDUOS2
  37 #define ASTRO_ID        0xFB
  38 #else
  39 #error No card type defined!
  40 #endif
  41
  42 /*
  43  * Define processor
  44  * possible values for Urmel board: only Coldfire M5373 processor supported
  45  * (please do not change)
  46  */
  47
  48 /* it seems not clear yet which processor defines we should use */
  49 #define CONFIG_MCF537x                  /* define processor family */
  50 #define CONFIG_MCF532x                  /* define processor family */
  51 #define CONFIG_M5373                    /* define processor type */
  52 #define CONFIG_ASTRO5373L               /* define board type */
  53
  54 /* Command line configuration */
  55 #include <config_cmd_default.h>
  56
  57 /*
  58  * CONFIG_RAM defines if u-boot is loaded via BDM (or started from
  59  * a different bootloader that has already performed RAM setup) or
  60  * started directly from flash, which is the regular case for production
  61  * boards.
  62  */
  63 #ifdef CONFIG_RAM
  64 #define CONFIG_MONITOR_IS_IN_RAM
  65 #define CONFIG_SYS_TEXT_BASE            0x40020000
  66 #define ENABLE_JFFS     0
  67 #else
  68 #define CONFIG_SYS_TEXT_BASE            0x00000000
  69 #define ENABLE_JFFS     1
  70 #endif
  71
  72 /* Define which commmands should be available at u-boot command prompt */
  73
  74 #define CONFIG_CMD_CACHE
  75 #define CONFIG_CMD_DATE
  76 #define CONFIG_CMD_ELF
  77 #define CONFIG_CMD_FLASH
  78 #define CONFIG_CMD_I2C
  79 #define CONFIG_CMD_MEMORY
  80 #define CONFIG_CMD_MISC
  81 #define CONFIG_CMD_XIMG
  82 #undef CONFIG_CMD_NET
  83 #undef CONFIG_CMD_NFS
  84 #if ENABLE_JFFS
  85 #define CONFIG_CMD_JFFS2
  86 #endif
  87 #define CONFIG_CMD_REGINFO
  88 #define CONFIG_CMD_LOADS
  89 #define CONFIG_CMD_LOADB
  90 #define CONFIG_CMD_FPGA
  91 #define CONFIG_CMDLINE_EDITING
  92
  93 #define CONFIG_SYS_HUSH_PARSER
  94
  95 #define CONFIG_MCFRTC
  96 #undef RTC_DEBUG
  97
  98 /* Timer */
  99 #define CONFIG_MCFTMR
 100 #undef CONFIG_MCFPIT
 101
 102 /* I2C */
 103 #define CONFIG_SYS_I2C
 104 #define CONFIG_SYS_I2C_FSL
 105 #define CONFIG_SYS_FSL_I2C_SPEED        80000
 106 #define CONFIG_SYS_FSL_I2C_SLAVE        0x7F
 107 #define CONFIG_SYS_FSL_I2C_OFFSET       0x58000
 108 #define CONFIG_SYS_IMMR                 CONFIG_SYS_MBAR
 109
 110 /*
 111  * Defines processor clock - important for correct timings concerning serial
 112  * interface etc.
 113  */
 114
 115 #define CONFIG_SYS_CLK                  80000000
 116 #define CONFIG_SYS_CPU_CLK              (CONFIG_SYS_CLK * 3)
 117 #define CONFIG_SYS_SDRAM_SIZE           32              /* SDRAM size in MB */
 118
 119 #define CONFIG_SYS_CORE_SRAM_SIZE       0x8000
 120 #define CONFIG_SYS_CORE_SRAM            0x80000000
 121
 122 #define CONFIG_SYS_UNIFY_CACHE
 123
 124 /*
 125  * Define baudrate for UART1 (console output, tftp, ...)
 126  * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud
 127  * CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected
 128  * in u-boot command interface
 129  */
 130
 131 #define CONFIG_BAUDRATE         115200
 132
 133 #define CONFIG_MCFUART
 134 #define CONFIG_SYS_UART_PORT            (2)
 135 #define CONFIG_SYS_UART2_ALT3_GPIO
 136
 137 /*
 138  * Watchdog configuration; Watchdog is disabled for running from RAM
 139  * and set to highest possible value else. Beware there is no check
 140  * in the watchdog code to validate the timeout value set here!
 141  */
 142
 143 #ifndef CONFIG_MONITOR_IS_IN_RAM
 144 #define CONFIG_WATCHDOG
 145 #define CONFIG_WATCHDOG_TIMEOUT 3355    /* timeout in milliseconds */
 146 #endif
 147
 148 /*
 149  * Configuration for environment
 150  * Environment is located in the last sector of the flash
 151  */
 152
 153 #ifndef CONFIG_MONITOR_IS_IN_RAM
 154 #define CONFIG_ENV_OFFSET               0x1FF8000
 155 #define CONFIG_ENV_SECT_SIZE            0x8000
 156 #define CONFIG_ENV_IS_IN_FLASH          1
 157 #else
 158 /*
 159  * environment in RAM - This is used to use a single PC-based application
 160  * to load an image, load U-Boot, load an environment and then start U-Boot
 161  * to execute the commands from the environment. Feedback is done via setting
 162  * and reading memory locations.
 163  */
 164 #define CONFIG_ENV_ADDR         0x40060000
 165 #define CONFIG_ENV_SECT_SIZE    0x8000
 166 #define CONFIG_ENV_IS_IN_FLASH  1
 167 #endif
 168
 169 /* here we put our FPGA configuration... */
 170 #define CONFIG_MISC_INIT_R      1
 171
 172 /* Define user parameters that have to be customized most likely */
 173
 174 /* AUTOBOOT settings - booting images automatically by u-boot after power on */
 175
 176 /*
 177  * used for autoboot, delay in seconds u-boot will wait before starting
 178  * defined (auto-)boot command, setting to -1 disables delay, setting to
 179  * 0 will too prevent access to u-boot command interface: u-boot then has
 180  * to be reflashed
 181  * beware - watchdog is not serviced during autoboot delay time!
 182  */
 183 #ifdef CONFIG_MONITOR_IS_IN_RAM
 184 #define CONFIG_BOOTDELAY        1
 185 #else
 186 #define CONFIG_BOOTDELAY        1
 187 #endif
 188
 189 /*
 190  * The following settings will be contained in the environment block ; if you
 191  * want to use a neutral environment all those settings can be manually set in
 192  * u-boot: 'set' command
 193  */
 194
 195 #define CONFIG_EXTRA_ENV_SETTINGS                       \
 196         "loaderversion=11\0"                            \
 197         "card_id="__stringify(ASTRO_ID)"\0"                     \
 198         "alterafile=0\0"                                \
 199         "xilinxfile=0\0"                                \
 200         "xilinxload=imxtract 0x540000 $xilinxfile 0x41000000&&"\
 201                 "fpga load 0 0x41000000 $filesize\0" \
 202         "alteraload=imxtract 0x6c0000 $alterafile 0x41000000&&"\
 203                 "fpga load 1 0x41000000 $filesize\0" \
 204         "env_default=1\0"                               \
 205         "env_check=if test $env_default -eq 1;"\
 206                 " then setenv env_default 0;saveenv;fi\0"
 207
 208 /*
 209  * "update" is a non-standard command that has to be supplied
 210  * by external update.c; This is not included in mainline because
 211  * it needs non-blocking CFI routines.
 212  */
 213 #ifdef CONFIG_MONITOR_IS_IN_RAM
 214 #define CONFIG_BOOTCOMMAND      ""      /* no autoboot in this case */
 215 #else
 216 #if CONFIG_ASTRO_V532
 217 #define CONFIG_BOOTCOMMAND      "protect off 0x80000 0x1ffffff;run env_check;"\
 218                                 "run xilinxload&&run alteraload&&bootm 0x80000;"\
 219                                 "update;reset"
 220 #else
 221 #define CONFIG_BOOTCOMMAND      "protect off 0x80000 0x1ffffff;run env_check;"\
 222                                 "run xilinxload&&bootm 0x80000;update;reset"
 223 #endif
 224 #endif
 225
 226 /* default bootargs that are considered during boot */
 227 #define CONFIG_BOOTARGS         " console=ttyS2,115200 rootfstype=romfs"\
 228                                 " loaderversion=$loaderversion"
 229
 230 #define CONFIG_SYS_PROMPT       "URMEL > "
 231
 232 /* default RAM address for user programs */
 233 #define CONFIG_SYS_LOAD_ADDR    0x20000
 234
 235 #define CONFIG_SYS_LONGHELP
 236
 237 #if (CONFIG_COMMANDS & CONFIG_CMD_KGDB)
 238 #define CONFIG_SYS_CBSIZE               1024
 239 #else
 240 #define CONFIG_SYS_CBSIZE               256
 241 #endif
 242 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
 243 #define CONFIG_SYS_MAXARGS              16
 244 #define CONFIG_SYS_BARGSIZE             CONFIG_SYS_CBSIZE
 245
 246 #define CONFIG_FPGA_COUNT       1
 247 #define CONFIG_FPGA
 248 #define CONFIG_FPGA_XILINX
 249 #define CONFIG_FPGA_SPARTAN3
 250 #define CONFIG_FPGA_ALTERA
 251 #define CONFIG_FPGA_CYCLON2
 252 #define CONFIG_SYS_FPGA_PROG_FEEDBACK
 253 #define CONFIG_SYS_FPGA_WAIT            1000
 254
 255 /* End of user parameters to be customized */
 256
 257 /* Defines memory range for test */
 258
 259 #define CONFIG_SYS_MEMTEST_START        0x40020000
 260 #define CONFIG_SYS_MEMTEST_END          0x41ffffff
 261
 262 /*
 263  * Low Level Configuration Settings
 264  * (address mappings, register initial values, etc.)
 265  * You should know what you are doing if you make changes here.
 266  */
 267
 268 /* Base register address */
 269
 270 #define CONFIG_SYS_MBAR         0xFC000000      /* Register Base Addrs */
 271
 272 /* System Conf. Reg. & System Protection Reg. */
 273
 274 #define CONFIG_SYS_SCR          0x0003;
 275 #define CONFIG_SYS_SPR          0xffff;
 276
 277 /*
 278  * Definitions for initial stack pointer and data area (in internal SRAM)
 279  */
 280 #define CONFIG_SYS_INIT_RAM_ADDR        0x80000000
 281 #define CONFIG_SYS_INIT_RAM_SIZE                0x8000
 282 #define CONFIG_SYS_INIT_RAM_CTRL        0x221
 283 #define CONFIG_SYS_GBL_DATA_OFFSET      (CONFIG_SYS_INIT_RAM_SIZE - \
 284                                          GENERATED_GBL_DATA_SIZE)
 285 #define CONFIG_SYS_INIT_SP_OFFSET       CONFIG_SYS_GBL_DATA_OFFSET
 286
 287 /*
 288  * Start addresses for the final memory configuration
 289  * (Set up by the startup code)
 290  * for MCF5373, the allowable range is 0x40000000 to 0x7FF00000
 291  */
 292 #define CONFIG_SYS_SDRAM_BASE           0x40000000
 293
 294 /*
 295  * Chipselect bank definitions
 296  *
 297  * CS0 - Flash 32MB (first 16MB)
 298  * CS1 - Flash 32MB (second half)
 299  * CS2 - FPGA
 300  * CS3 - FPGA
 301  * CS4 - unused
 302  * CS5 - unused
 303  */
 304 #define CONFIG_SYS_CS0_BASE             0
 305 #define CONFIG_SYS_CS0_MASK             0x00ff0001
 306 #define CONFIG_SYS_CS0_CTRL             0x00001fc0
 307
 308 #define CONFIG_SYS_CS1_BASE             0x01000000
 309 #define CONFIG_SYS_CS1_MASK             0x00ff0001
 310 #define CONFIG_SYS_CS1_CTRL             0x00001fc0
 311
 312 #define CONFIG_SYS_CS2_BASE             0x20000000
 313 #define CONFIG_SYS_CS2_MASK             0x00ff0001
 314 #define CONFIG_SYS_CS2_CTRL             0x0000fec0
 315
 316 #define CONFIG_SYS_CS3_BASE             0x21000000
 317 #define CONFIG_SYS_CS3_MASK             0x00ff0001
 318 #define CONFIG_SYS_CS3_CTRL             0x0000fec0
 319
 320 #define CONFIG_SYS_FLASH_BASE           0x00000000
 321
 322 #ifdef  CONFIG_MONITOR_IS_IN_RAM
 323 #define CONFIG_SYS_MONITOR_BASE         CONFIG_SYS_TEXT_BASE
 324 #else
 325 /* This is mainly used during relocation in start.S */
 326 #define CONFIG_SYS_MONITOR_BASE         (CONFIG_SYS_FLASH_BASE + 0x400)
 327 #endif
 328 /* Reserve 256 kB for Monitor */
 329 #define CONFIG_SYS_MONITOR_LEN          (256 << 10)
 330
 331 #define CONFIG_SYS_BOOTPARAMS_LEN       (64 * 1024)
 332 /* Reserve 128 kB for malloc() */
 333 #define CONFIG_SYS_MALLOC_LEN           (128 << 10)
 334
 335 /*
 336  * For booting Linux, the board info and command line data
 337  * have to be in the first 8 MB of memory, since this is
 338  * the maximum mapped by the Linux kernel during initialization ??
 339  */
 340 #define CONFIG_SYS_BOOTMAPSZ            (CONFIG_SYS_SDRAM_BASE + \
 341                                                 (CONFIG_SYS_SDRAM_SIZE << 20))
 342
 343 /* FLASH organization */
 344 #define CONFIG_SYS_MAX_FLASH_BANKS      1
 345 #define CONFIG_SYS_MAX_FLASH_SECT       259
 346 #define CONFIG_SYS_FLASH_ERASE_TOUT     1000
 347
 348 #define CONFIG_SYS_FLASH_CFI            1
 349 #define CONFIG_FLASH_CFI_DRIVER         1
 350 #define CONFIG_SYS_FLASH_SIZE           0x2000000
 351 #define CONFIG_SYS_FLASH_PROTECTION     1
 352 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE       1
 353 #define CONFIG_SYS_FLASH_CFI_NONBLOCK   1
 354
 355 #if ENABLE_JFFS
 356 /* JFFS Partition offset set */
 357 #define CONFIG_SYS_JFFS2_FIRST_BANK    0
 358 #define CONFIG_SYS_JFFS2_NUM_BANKS     1
 359 /* 512k reserved for u-boot */
 360 #define CONFIG_SYS_JFFS2_FIRST_SECTOR  0x40
 361 #endif
 362
 363 /* Cache Configuration */
 364 #define CONFIG_SYS_CACHELINE_SIZE       16
 365
 366 #define ICACHE_STATUS                   (CONFIG_SYS_INIT_RAM_ADDR + \
 367                                          CONFIG_SYS_INIT_RAM_SIZE - 8)
 368 #define DCACHE_STATUS                   (CONFIG_SYS_INIT_RAM_ADDR + \
 369                                          CONFIG_SYS_INIT_RAM_SIZE - 4)
 370 #define CONFIG_SYS_ICACHE_INV           (CF_CACR_CINVA)
 371 #define CONFIG_SYS_CACHE_ACR0           (CONFIG_SYS_SDRAM_BASE | \
 372                                          CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
 373                                          CF_ACR_EN | CF_ACR_SM_ALL)
 374 #define CONFIG_SYS_CACHE_ICACR          (CF_CACR_EC | CF_CACR_CINVA | \
 375                                          CF_CACR_DCM_P)
 376
 377 #endif  /* _CONFIG_ASTRO_MCF5373L_H */