include/configs/edminiv2.h

   1 /*
   2  * Copyright (C) 2010 Albert ARIBAUD <albert.u.boot@aribaud.net>
   3  *
   4  * Based on original Kirkwood support which is
   5  * (C) Copyright 2009
   6  * Marvell Semiconductor <www.marvell.com>
   7  * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
   8  *
   9  * SPDX-License-Identifier:     GPL-2.0+
  10  */
  11
  12 #ifndef _CONFIG_EDMINIV2_H
  13 #define _CONFIG_EDMINIV2_H
  14
  15 /*
  16  * Version number information
  17  */
  18
  19 #define CONFIG_IDENT_STRING     " EDMiniV2"
  20
  21 /*
  22  * High Level Configuration Options (easy to change)
  23  */
  24
  25 #define CONFIG_MARVELL          1
  26 #define CONFIG_ARM926EJS        1       /* Basic Architecture */
  27 #define CONFIG_FEROCEON         1       /* CPU Core subversion */
  28 #define CONFIG_88F5182          1       /* SOC Name */
  29 #define CONFIG_MACH_EDMINIV2    1       /* Machine type */
  30
  31 #include <asm/arch/orion5x.h>
  32 /*
  33  * CLKs configurations
  34  */
  35
  36 /*
  37  * Board-specific values for Orion5x MPP low level init:
  38  * - MPPs 12 to 15 are SATA LEDs (mode 5)
  39  * - Others are GPIO/unused (mode 3 for MPP0, mode 5 for
  40  *   MPP16 to MPP19, mode 0 for others
  41  */
  42
  43 #define ORION5X_MPP0_7          0x00000003
  44 #define ORION5X_MPP8_15         0x55550000
  45 #define ORION5X_MPP16_23        0x00005555
  46
  47 /*
  48  * Board-specific values for Orion5x GPIO low level init:
  49  * - GPIO3 is input (RTC interrupt)
  50  * - GPIO16 is Power LED control (0 = on, 1 = off)
  51  * - GPIO17 is Power LED source select (0 = CPLD, 1 = GPIO16)
  52  * - GPIO18 is Power Button status (0 = Released, 1 = Pressed)
  53  * - GPIO19 is SATA disk power toggle (toggles on 0-to-1)
  54  * - GPIO22 is SATA disk power status ()
  55  * - GPIO23 is supply status for SATA disk ()
  56  * - GPIO24 is supply control for board (write 1 to power off)
  57  * Last GPIO is 25, further bits are supposed to be 0.
  58  * Enable mask has ones for INPUT, 0 for OUTPUT.
  59  * Default is LED ON, board ON :)
  60  */
  61
  62 #define ORION5X_GPIO_OUT_ENABLE         0xfef4f0ca
  63 #define ORION5X_GPIO_OUT_VALUE          0x00000000
  64 #define ORION5X_GPIO_IN_POLARITY        0x000000d0
  65
  66 /*
  67  * NS16550 Configuration
  68  */
  69
  70 #define CONFIG_SYS_NS16550
  71 #define CONFIG_SYS_NS16550_SERIAL
  72 #define CONFIG_SYS_NS16550_REG_SIZE     (-4)
  73 #define CONFIG_SYS_NS16550_CLK          CONFIG_SYS_TCLK
  74 #define CONFIG_SYS_NS16550_COM1         ORION5X_UART0_BASE
  75
  76 /*
  77  * Serial Port configuration
  78  * The following definitions let you select what serial you want to use
  79  * for your console driver.
  80  */
  81
  82 #define CONFIG_CONS_INDEX       1       /*Console on UART0 */
  83 #define CONFIG_BAUDRATE                 115200
  84 #define CONFIG_SYS_BAUDRATE_TABLE \
  85         { 9600, 19200, 38400, 57600, 115200, 230400, 460800, 921600 }
  86
  87 /*
  88  * FLASH configuration
  89  */
  90
  91 #define CONFIG_SYS_FLASH_CFI
  92 #define CONFIG_FLASH_CFI_DRIVER
  93 #define CONFIG_FLASH_CFI_LEGACY
  94 #define CONFIG_SYS_MAX_FLASH_BANKS      1  /* max num of flash banks       */
  95 #define CONFIG_SYS_MAX_FLASH_SECT       11 /* max num of sects on one chip */
  96 #define CONFIG_SYS_FLASH_BASE           0xfff80000
  97 #define CONFIG_SYS_FLASH_SECTSZ \
  98         {16384, 8192, 8192, 32768, \
  99          65536, 65536, 65536, 65536, 65536, 65536, 65536}
 100
 101 /* auto boot */
 102 #define CONFIG_BOOTDELAY        3       /* default enable autoboot */
 103
 104 /*
 105  * For booting Linux, the board info and command line data
 106  * have to be in the first 8 MB of memory, since this is
 107  * the maximum mapped by the Linux kernel during initialization.
 108  */
 109 #define CONFIG_CMDLINE_TAG      1       /* enable passing of ATAGs  */
 110 #define CONFIG_INITRD_TAG       1       /* enable INITRD tag */
 111 #define CONFIG_SETUP_MEMORY_TAGS 1      /* enable memory tag */
 112
 113 #define CONFIG_SYS_PROMPT       "EDMiniV2> "    /* Command Prompt */
 114 #define CONFIG_SYS_CBSIZE       1024    /* Console I/O Buff Size */
 115 #define CONFIG_SYS_PBSIZE       (CONFIG_SYS_CBSIZE \
 116                 +sizeof(CONFIG_SYS_PROMPT) + 16)        /* Print Buff */
 117 /*
 118  * Commands configuration - using default command set for now
 119  */
 120 #include <config_cmd_default.h>
 121 #define CONFIG_CMD_IDE
 122 #define CONFIG_CMD_I2C
 123 #define CONFIG_CMD_USB
 124
 125 /*
 126  * Network
 127  */
 128
 129 #ifdef CONFIG_CMD_NET
 130 #define CONFIG_MVGBE                            /* Enable Marvell GbE Driver */
 131 #define CONFIG_MVGBE_PORTS      {1}             /* enable port 0 only */
 132 #define CONFIG_SKIP_LOCAL_MAC_RANDOMIZATION     /* don't randomize MAC */
 133 #define CONFIG_PHY_BASE_ADR     0x8
 134 #define CONFIG_RESET_PHY_R      /* use reset_phy() to init mv8831116 PHY */
 135 #define CONFIG_NETCONSOLE       /* include NetConsole support   */
 136 #define CONFIG_MII              /* expose smi ove miiphy interface */
 137 #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */
 138 #define CONFIG_ENV_OVERWRITE    /* ethaddr can be reprogrammed */
 139 #endif
 140
 141 /*
 142  * IDE
 143  */
 144 #ifdef CONFIG_CMD_IDE
 145 #define __io
 146 #define CONFIG_IDE_PREINIT
 147 #define CONFIG_DOS_PARTITION
 148 #define CONFIG_CMD_EXT2
 149 /* ED Mini V has an IDE-compatible SATA connector for port 1 */
 150 #define CONFIG_MVSATA_IDE
 151 #define CONFIG_MVSATA_IDE_USE_PORT1
 152 /* Needs byte-swapping for ATA data register */
 153 #define CONFIG_IDE_SWAP_IO
 154 /* Data, registers and alternate blocks are at the same offset */
 155 #define CONFIG_SYS_ATA_DATA_OFFSET      (0x0100)
 156 #define CONFIG_SYS_ATA_REG_OFFSET       (0x0100)
 157 #define CONFIG_SYS_ATA_ALT_OFFSET       (0x0100)
 158 /* Each 8-bit ATA register is aligned to a 4-bytes address */
 159 #define CONFIG_SYS_ATA_STRIDE           4
 160 /* Controller supports 48-bits LBA addressing */
 161 #define CONFIG_LBA48
 162 /* A single bus, a single device */
 163 #define CONFIG_SYS_IDE_MAXBUS           1
 164 #define CONFIG_SYS_IDE_MAXDEVICE        1
 165 /* ATA registers base is at SATA controller base */
 166 #define CONFIG_SYS_ATA_BASE_ADDR        ORION5X_SATA_BASE
 167 /* ATA bus 0 is orion5x port 1 on ED Mini V2 */
 168 #define CONFIG_SYS_ATA_IDE0_OFFSET      ORION5X_SATA_PORT1_OFFSET
 169 /* end of IDE defines */
 170 #endif /* CMD_IDE */
 171
 172 /*
 173  * Common USB/EHCI configuration
 174  */
 175 #ifdef CONFIG_CMD_USB
 176 #define CONFIG_USB_EHCI         /* Enable EHCI USB support */
 177 #define CONFIG_USB_EHCI_MARVELL
 178 #define ORION5X_USB20_HOST_PORT_BASE ORION5X_USB20_PORT0_BASE
 179 #define CONFIG_USB_STORAGE
 180 #define CONFIG_DOS_PARTITION
 181 #define CONFIG_ISO_PARTITION
 182 #define CONFIG_SUPPORT_VFAT
 183 #endif /* CONFIG_CMD_USB */
 184
 185 /*
 186  * I2C related stuff
 187  */
 188 #ifdef CONFIG_CMD_I2C
 189 #define CONFIG_SYS_I2C
 190 #define CONFIG_SYS_I2C_MVTWSI
 191 #define CONFIG_I2C_MVTWSI_BASE          ORION5X_TWSI_BASE
 192 #define CONFIG_SYS_I2C_SLAVE            0x0
 193 #define CONFIG_SYS_I2C_SPEED            100000
 194 #endif
 195
 196 /*
 197  *  Environment variables configurations
 198  */
 199 #define CONFIG_ENV_IS_IN_FLASH          1
 200 #define CONFIG_ENV_SECT_SIZE            0x2000  /* 16K */
 201 #define CONFIG_ENV_SIZE                 0x2000
 202 #define CONFIG_ENV_OFFSET               0x4000  /* env starts here */
 203
 204 /*
 205  * Size of malloc() pool
 206  */
 207 #define CONFIG_SYS_MALLOC_LEN   (1024 * 256) /* 256kB for malloc() */
 208
 209 /*
 210  * Other required minimal configurations
 211  */
 212 #define CONFIG_CONSOLE_INFO_QUIET       /* some code reduction */
 213 #define CONFIG_ARCH_CPU_INIT            /* call arch_cpu_init() */
 214 #define CONFIG_ARCH_MISC_INIT           /* call arch_misc_init() */
 215 #define CONFIG_DISPLAY_CPUINFO          /* Display cpu info */
 216 #define CONFIG_NR_DRAM_BANKS            1
 217
 218 #define CONFIG_SYS_LOAD_ADDR            0x00800000
 219 #define CONFIG_SYS_MEMTEST_START        0x00400000
 220 #define CONFIG_SYS_MEMTEST_END          0x007fffff
 221 #define CONFIG_SYS_RESET_ADDRESS        0xffff0000
 222 #define CONFIG_SYS_MAXARGS              16
 223
 224 /* Use the HUSH parser */
 225 #define CONFIG_SYS_HUSH_PARSER
 226
 227 /* Enable command line editing */
 228 #define CONFIG_CMDLINE_EDITING
 229
 230 /* provide extensive help */
 231 #define CONFIG_SYS_LONGHELP
 232
 233 /* additions for new relocation code, must be added to all boards */
 234 #define CONFIG_SYS_SDRAM_BASE           0
 235 #define CONFIG_SYS_INIT_SP_ADDR \
 236         (CONFIG_SYS_SDRAM_BASE + 0x1000 - GENERATED_GBL_DATA_SIZE)
 237
 238 #endif /* _CONFIG_EDMINIV2_H */