include/configs/ls2080ardb.h

   1 /*
   2  * Copyright 2017 NXP
   3  * Copyright 2015 Freescale Semiconductor
   4  *
   5  * SPDX-License-Identifier:     GPL-2.0+
   6  */
   7
   8 #ifndef __LS2_RDB_H
   9 #define __LS2_RDB_H
  10
  11 #include "ls2080a_common.h"
  12
  13 #undef CONFIG_CONS_INDEX
  14 #define CONFIG_CONS_INDEX       2
  15
  16 #ifdef CONFIG_FSL_QSPI
  17 #ifdef CONFIG_TARGET_LS2081ARDB
  18 #define CONFIG_QIXIS_I2C_ACCESS
  19 #endif
  20 #define CONFIG_SYS_I2C_EARLY_INIT
  21 #define CONFIG_DISPLAY_BOARDINFO_LATE
  22 #endif
  23
  24 #define I2C_MUX_CH_VOL_MONITOR          0xa
  25 #define I2C_VOL_MONITOR_ADDR            0x38
  26 #define CONFIG_VOL_MONITOR_IR36021_READ
  27 #define CONFIG_VOL_MONITOR_IR36021_SET
  28
  29 #define CONFIG_VID_FLS_ENV              "ls2080ardb_vdd_mv"
  30 #ifndef CONFIG_SPL_BUILD
  31 #define CONFIG_VID
  32 #endif
  33 /* step the IR regulator in 5mV increments */
  34 #define IR_VDD_STEP_DOWN                5
  35 #define IR_VDD_STEP_UP                  5
  36 /* The lowest and highest voltage allowed for LS2080ARDB */
  37 #define VDD_MV_MIN                      819
  38 #define VDD_MV_MAX                      1212
  39
  40 #ifndef __ASSEMBLY__
  41 unsigned long get_board_sys_clk(void);
  42 #endif
  43
  44 #define CONFIG_SYS_CLK_FREQ             get_board_sys_clk()
  45 #define CONFIG_DDR_CLK_FREQ             133333333
  46 #define COUNTER_FREQUENCY_REAL          (CONFIG_SYS_CLK_FREQ/4)
  47
  48 #define CONFIG_DDR_SPD
  49 #define CONFIG_DDR_ECC
  50 #define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
  51 #define CONFIG_MEM_INIT_VALUE           0xdeadbeef
  52 #define SPD_EEPROM_ADDRESS1     0x51
  53 #define SPD_EEPROM_ADDRESS2     0x52
  54 #define SPD_EEPROM_ADDRESS3     0x53
  55 #define SPD_EEPROM_ADDRESS4     0x54
  56 #define SPD_EEPROM_ADDRESS5     0x55
  57 #define SPD_EEPROM_ADDRESS6     0x56    /* dummy address */
  58 #define SPD_EEPROM_ADDRESS      SPD_EEPROM_ADDRESS1
  59 #define CONFIG_SYS_SPD_BUS_NUM  0       /* SPD on I2C bus 0 */
  60 #define CONFIG_DIMM_SLOTS_PER_CTLR              2
  61 #define CONFIG_CHIP_SELECTS_PER_CTRL            4
  62 #ifdef CONFIG_SYS_FSL_HAS_DP_DDR
  63 #define CONFIG_DP_DDR_DIMM_SLOTS_PER_CTLR       1
  64 #endif
  65 #define CONFIG_FSL_DDR_BIST     /* enable built-in memory test */
  66
  67 /* SATA */
  68 #define CONFIG_LIBATA
  69 #define CONFIG_SCSI_AHCI
  70 #define CONFIG_SCSI_AHCI_PLAT
  71
  72 #define CONFIG_SYS_SATA1                        AHCI_BASE_ADDR1
  73 #define CONFIG_SYS_SATA2                        AHCI_BASE_ADDR2
  74
  75 #define CONFIG_SYS_SCSI_MAX_SCSI_ID             1
  76 #define CONFIG_SYS_SCSI_MAX_LUN                 1
  77 #define CONFIG_SYS_SCSI_MAX_DEVICE              (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
  78                                                 CONFIG_SYS_SCSI_MAX_LUN)
  79
  80 #ifndef CONFIG_FSL_QSPI
  81 /* undefined CONFIG_FSL_DDR_SYNC_REFRESH for simulator */
  82
  83 #define CONFIG_SYS_NOR0_CSPR_EXT        (0x0)
  84 #define CONFIG_SYS_NOR_AMASK            IFC_AMASK(128*1024*1024)
  85 #define CONFIG_SYS_NOR_AMASK_EARLY      IFC_AMASK(64*1024*1024)
  86
  87 #define CONFIG_SYS_NOR0_CSPR                                    \
  88         (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS)             | \
  89         CSPR_PORT_SIZE_16                                       | \
  90         CSPR_MSEL_NOR                                           | \
  91         CSPR_V)
  92 #define CONFIG_SYS_NOR0_CSPR_EARLY                              \
  93         (CSPR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS_EARLY)       | \
  94         CSPR_PORT_SIZE_16                                       | \
  95         CSPR_MSEL_NOR                                           | \
  96         CSPR_V)
  97 #define CONFIG_SYS_NOR_CSOR     CSOR_NOR_ADM_SHIFT(12)
  98 #define CONFIG_SYS_NOR_FTIM0    (FTIM0_NOR_TACSE(0x4) | \
  99                                 FTIM0_NOR_TEADC(0x5) | \
 100                                 FTIM0_NOR_TEAHC(0x5))
 101 #define CONFIG_SYS_NOR_FTIM1    (FTIM1_NOR_TACO(0x35) | \
 102                                 FTIM1_NOR_TRAD_NOR(0x1a) |\
 103                                 FTIM1_NOR_TSEQRAD_NOR(0x13))
 104 #define CONFIG_SYS_NOR_FTIM2    (FTIM2_NOR_TCS(0x4) | \
 105                                 FTIM2_NOR_TCH(0x4) | \
 106                                 FTIM2_NOR_TWPH(0x0E) | \
 107                                 FTIM2_NOR_TWP(0x1c))
 108 #define CONFIG_SYS_NOR_FTIM3    0x04000000
 109 #define CONFIG_SYS_IFC_CCR      0x01000000
 110
 111 #ifdef CONFIG_MTD_NOR_FLASH
 112 #define CONFIG_FLASH_CFI_DRIVER
 113 #define CONFIG_SYS_FLASH_CFI
 114 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
 115 #define CONFIG_SYS_FLASH_QUIET_TEST
 116 #define CONFIG_FLASH_SHOW_PROGRESS      45 /* count down from 45/5: 9..1 */
 117
 118 #define CONFIG_SYS_MAX_FLASH_BANKS      1       /* number of banks */
 119 #define CONFIG_SYS_MAX_FLASH_SECT       1024    /* sectors per device */
 120 #define CONFIG_SYS_FLASH_ERASE_TOUT     60000   /* Flash Erase Timeout (ms) */
 121 #define CONFIG_SYS_FLASH_WRITE_TOUT     500     /* Flash Write Timeout (ms) */
 122
 123 #define CONFIG_SYS_FLASH_EMPTY_INFO
 124 #define CONFIG_SYS_FLASH_BANKS_LIST     { CONFIG_SYS_FLASH_BASE,\
 125                                          CONFIG_SYS_FLASH_BASE + 0x40000000}
 126 #endif
 127
 128 #define CONFIG_NAND_FSL_IFC
 129 #define CONFIG_SYS_NAND_MAX_ECCPOS      256
 130 #define CONFIG_SYS_NAND_MAX_OOBFREE     2
 131
 132 #define CONFIG_SYS_NAND_CSPR_EXT        (0x0)
 133 #define CONFIG_SYS_NAND_CSPR    (CSPR_PHYS_ADDR(CONFIG_SYS_NAND_BASE_PHYS) \
 134                                 | CSPR_PORT_SIZE_8 /* Port Size = 8 bit */ \
 135                                 | CSPR_MSEL_NAND        /* MSEL = NAND */ \
 136                                 | CSPR_V)
 137 #define CONFIG_SYS_NAND_AMASK   IFC_AMASK(64 * 1024)
 138
 139 #define CONFIG_SYS_NAND_CSOR    (CSOR_NAND_ECC_ENC_EN   /* ECC on encode */ \
 140                                 | CSOR_NAND_ECC_DEC_EN  /* ECC on decode */ \
 141                                 | CSOR_NAND_ECC_MODE_4  /* 4-bit ECC */ \
 142                                 | CSOR_NAND_RAL_3       /* RAL = 3Byes */ \
 143                                 | CSOR_NAND_PGS_4K      /* Page Size = 4K */ \
 144                                 | CSOR_NAND_SPRZ_224    /* Spare size = 224 */ \
 145                                 | CSOR_NAND_PB(128))    /* Pages Per Block 128*/
 146
 147 #define CONFIG_SYS_NAND_ONFI_DETECTION
 148
 149 /* ONFI NAND Flash mode0 Timing Params */
 150 #define CONFIG_SYS_NAND_FTIM0           (FTIM0_NAND_TCCST(0x0e) | \
 151                                         FTIM0_NAND_TWP(0x30)   | \
 152                                         FTIM0_NAND_TWCHT(0x0e) | \
 153                                         FTIM0_NAND_TWH(0x14))
 154 #define CONFIG_SYS_NAND_FTIM1           (FTIM1_NAND_TADLE(0x64) | \
 155                                         FTIM1_NAND_TWBE(0xab)  | \
 156                                         FTIM1_NAND_TRR(0x1c)   | \
 157                                         FTIM1_NAND_TRP(0x30))
 158 #define CONFIG_SYS_NAND_FTIM2           (FTIM2_NAND_TRAD(0x1e) | \
 159                                         FTIM2_NAND_TREH(0x14) | \
 160                                         FTIM2_NAND_TWHRE(0x3c))
 161 #define CONFIG_SYS_NAND_FTIM3           0x0
 162
 163 #define CONFIG_SYS_NAND_BASE_LIST       { CONFIG_SYS_NAND_BASE }
 164 #define CONFIG_SYS_MAX_NAND_DEVICE      1
 165 #define CONFIG_MTD_NAND_VERIFY_WRITE
 166 #define CONFIG_CMD_NAND
 167
 168 #define CONFIG_SYS_NAND_BLOCK_SIZE      (512 * 1024)
 169 #define CONFIG_FSL_QIXIS        /* use common QIXIS code */
 170 #define QIXIS_LBMAP_SWITCH              0x06
 171 #define QIXIS_LBMAP_MASK                0x0f
 172 #define QIXIS_LBMAP_SHIFT               0
 173 #define QIXIS_LBMAP_DFLTBANK            0x00
 174 #define QIXIS_LBMAP_ALTBANK             0x04
 175 #define QIXIS_LBMAP_NAND                0x09
 176 #define QIXIS_RST_CTL_RESET             0x31
 177 #define QIXIS_RST_CTL_RESET_EN          0x30
 178 #define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
 179 #define QIXIS_RCFG_CTL_RECONFIG_START   0x21
 180 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
 181 #define QIXIS_RCW_SRC_NAND              0x119
 182 #define QIXIS_RST_FORCE_MEM             0x01
 183
 184 #define CONFIG_SYS_CSPR3_EXT    (0x0)
 185 #define CONFIG_SYS_CSPR3        (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS_EARLY) \
 186                                 | CSPR_PORT_SIZE_8 \
 187                                 | CSPR_MSEL_GPCM \
 188                                 | CSPR_V)
 189 #define CONFIG_SYS_CSPR3_FINAL  (CSPR_PHYS_ADDR(QIXIS_BASE_PHYS) \
 190                                 | CSPR_PORT_SIZE_8 \
 191                                 | CSPR_MSEL_GPCM \
 192                                 | CSPR_V)
 193
 194 #define CONFIG_SYS_AMASK3       IFC_AMASK(64*1024)
 195 #define CONFIG_SYS_CSOR3        CSOR_GPCM_ADM_SHIFT(12)
 196 /* QIXIS Timing parameters for IFC CS3 */
 197 #define CONFIG_SYS_CS3_FTIM0            (FTIM0_GPCM_TACSE(0x0e) | \
 198                                         FTIM0_GPCM_TEADC(0x0e) | \
 199                                         FTIM0_GPCM_TEAHC(0x0e))
 200 #define CONFIG_SYS_CS3_FTIM1            (FTIM1_GPCM_TACO(0xff) | \
 201                                         FTIM1_GPCM_TRAD(0x3f))
 202 #define CONFIG_SYS_CS3_FTIM2            (FTIM2_GPCM_TCS(0xf) | \
 203                                         FTIM2_GPCM_TCH(0xf) | \
 204                                         FTIM2_GPCM_TWP(0x3E))
 205 #define CONFIG_SYS_CS3_FTIM3            0x0
 206
 207 #if defined(CONFIG_SPL) && defined(CONFIG_NAND)
 208 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 209 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NOR0_CSPR_EARLY
 210 #define CONFIG_SYS_CSPR2_FINAL          CONFIG_SYS_NOR0_CSPR
 211 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NOR_AMASK
 212 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NOR_CSOR
 213 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NOR_FTIM0
 214 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NOR_FTIM1
 215 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NOR_FTIM2
 216 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NOR_FTIM3
 217 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NAND_CSPR_EXT
 218 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NAND_CSPR
 219 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NAND_AMASK
 220 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NAND_CSOR
 221 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NAND_FTIM0
 222 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NAND_FTIM1
 223 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NAND_FTIM2
 224 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NAND_FTIM3
 225
 226 #define CONFIG_ENV_OFFSET               (2048 * 1024)
 227 #define CONFIG_ENV_SECT_SIZE            0x20000
 228 #define CONFIG_ENV_SIZE                 0x2000
 229 #define CONFIG_SPL_PAD_TO               0x80000
 230 #define CONFIG_SYS_NAND_U_BOOT_OFFS     (1024 * 1024)
 231 #define CONFIG_SYS_NAND_U_BOOT_SIZE     (512 * 1024)
 232 #else
 233 #define CONFIG_SYS_CSPR0_EXT            CONFIG_SYS_NOR0_CSPR_EXT
 234 #define CONFIG_SYS_CSPR0                CONFIG_SYS_NOR0_CSPR_EARLY
 235 #define CONFIG_SYS_CSPR0_FINAL          CONFIG_SYS_NOR0_CSPR
 236 #define CONFIG_SYS_AMASK0               CONFIG_SYS_NOR_AMASK
 237 #define CONFIG_SYS_CSOR0                CONFIG_SYS_NOR_CSOR
 238 #define CONFIG_SYS_CS0_FTIM0            CONFIG_SYS_NOR_FTIM0
 239 #define CONFIG_SYS_CS0_FTIM1            CONFIG_SYS_NOR_FTIM1
 240 #define CONFIG_SYS_CS0_FTIM2            CONFIG_SYS_NOR_FTIM2
 241 #define CONFIG_SYS_CS0_FTIM3            CONFIG_SYS_NOR_FTIM3
 242 #define CONFIG_SYS_CSPR2_EXT            CONFIG_SYS_NAND_CSPR_EXT
 243 #define CONFIG_SYS_CSPR2                CONFIG_SYS_NAND_CSPR
 244 #define CONFIG_SYS_AMASK2               CONFIG_SYS_NAND_AMASK
 245 #define CONFIG_SYS_CSOR2                CONFIG_SYS_NAND_CSOR
 246 #define CONFIG_SYS_CS2_FTIM0            CONFIG_SYS_NAND_FTIM0
 247 #define CONFIG_SYS_CS2_FTIM1            CONFIG_SYS_NAND_FTIM1
 248 #define CONFIG_SYS_CS2_FTIM2            CONFIG_SYS_NAND_FTIM2
 249 #define CONFIG_SYS_CS2_FTIM3            CONFIG_SYS_NAND_FTIM3
 250
 251 #define CONFIG_ENV_ADDR                 (CONFIG_SYS_FLASH_BASE + 0x300000)
 252 #define CONFIG_ENV_SECT_SIZE            0x20000
 253 #define CONFIG_ENV_SIZE                 0x2000
 254 #endif
 255
 256 /* Debug Server firmware */
 257 #define CONFIG_SYS_DEBUG_SERVER_FW_IN_NOR
 258 #define CONFIG_SYS_DEBUG_SERVER_FW_ADDR 0x580D00000ULL
 259 #endif
 260 #define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
 261
 262 #ifdef CONFIG_TARGET_LS2081ARDB
 263 #define CONFIG_FSL_QIXIS        /* use common QIXIS code */
 264 #define QIXIS_QMAP_MASK                 0x07
 265 #define QIXIS_QMAP_SHIFT                5
 266 #define QIXIS_LBMAP_DFLTBANK            0x00
 267 #define QIXIS_LBMAP_QSPI                0x00
 268 #define QIXIS_RCW_SRC_QSPI              0x62
 269 #define QIXIS_LBMAP_ALTBANK             0x20
 270 #define QIXIS_RST_CTL_RESET             0x31
 271 #define QIXIS_RCFG_CTL_RECONFIG_IDLE    0x20
 272 #define QIXIS_RCFG_CTL_RECONFIG_START   0x21
 273 #define QIXIS_RCFG_CTL_WATCHDOG_ENBLE   0x08
 274 #define QIXIS_LBMAP_MASK                0x0f
 275 #define QIXIS_RST_CTL_RESET_EN          0x30
 276 #endif
 277
 278 /*
 279  * I2C
 280  */
 281 #ifdef CONFIG_TARGET_LS2081ARDB
 282 #define CONFIG_SYS_I2C_FPGA_ADDR        0x66
 283 #endif
 284 #define I2C_MUX_PCA_ADDR                0x75
 285 #define I2C_MUX_PCA_ADDR_PRI            0x75 /* Primary Mux*/
 286
 287 /* I2C bus multiplexer */
 288 #define I2C_MUX_CH_DEFAULT      0x8
 289
 290 /* SPI */
 291 #if defined(CONFIG_FSL_QSPI) || defined(CONFIG_FSL_DSPI)
 292 #define CONFIG_SPI_FLASH
 293 #ifdef CONFIG_FSL_QSPI
 294 #define CONFIG_SPI_FLASH_STMICRO
 295 #endif
 296 #ifdef CONFIG_FSL_QSPI
 297 #ifdef CONFIG_TARGET_LS2081ARDB
 298 #define CONFIG_SPI_FLASH_STMICRO
 299 #else
 300 #define CONFIG_SPI_FLASH_SPANSION
 301 #endif
 302 #define FSL_QSPI_FLASH_SIZE             SZ_64M  /* 64MB */
 303 #define FSL_QSPI_FLASH_NUM              2
 304 #endif
 305 #endif
 306
 307 /*
 308  * RTC configuration
 309  */
 310 #define RTC
 311 #ifdef CONFIG_TARGET_LS2081ARDB
 312 #define CONFIG_RTC_PCF8563              1
 313 #define CONFIG_SYS_I2C_RTC_ADDR         0x51
 314 #else
 315 #define CONFIG_RTC_DS3231               1
 316 #define CONFIG_SYS_I2C_RTC_ADDR         0x68
 317 #endif
 318
 319 /* EEPROM */
 320 #define CONFIG_ID_EEPROM
 321 #define CONFIG_SYS_I2C_EEPROM_NXID
 322 #define CONFIG_SYS_EEPROM_BUS_NUM       0
 323 #define CONFIG_SYS_I2C_EEPROM_ADDR      0x57
 324 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN  1
 325 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
 326 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
 327
 328 #define CONFIG_FSL_MEMAC
 329
 330 #ifdef CONFIG_PCI
 331 #define CONFIG_PCI_SCAN_SHOW
 332 #define CONFIG_CMD_PCI
 333 #endif
 334
 335 /*  MMC  */
 336 #ifdef CONFIG_MMC
 337 #define CONFIG_FSL_ESDHC
 338 #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
 339 #endif
 340
 341 #define CONFIG_MISC_INIT_R
 342
 343 /*
 344  * USB
 345  */
 346 #define CONFIG_HAS_FSL_XHCI_USB
 347 #define CONFIG_USB_XHCI_FSL
 348 #define CONFIG_USB_MAX_CONTROLLER_COUNT         2
 349 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS      2
 350
 351 #undef CONFIG_CMDLINE_EDITING
 352 #include <config_distro_defaults.h>
 353
 354 #define BOOT_TARGET_DEVICES(func) \
 355         func(USB, usb, 0) \
 356         func(MMC, mmc, 0) \
 357         func(SCSI, scsi, 0) \
 358         func(DHCP, dhcp, na)
 359 #include <config_distro_bootcmd.h>
 360
 361 #ifdef CONFIG_QSPI_BOOT
 362 #define MC_INIT_CMD                             \
 363         "mcinitcmd=env exists secureboot && "   \
 364         "esbc_validate 0x20700000 && "          \
 365         "esbc_validate 0x20740000;"             \
 366         "fsl_mc start mc 0x20a00000 0x20e00000 \0"
 367 #else
 368 #define MC_INIT_CMD                             \
 369         "mcinitcmd=env exists secureboot && "   \
 370         "esbc_validate 0x580700000 && "         \
 371         "esbc_validate 0x580740000; "           \
 372         "fsl_mc start mc 0x580a00000 0x580e00000 \0"
 373 #endif
 374
 375 /* Initial environment variables */
 376 #undef CONFIG_EXTRA_ENV_SETTINGS
 377 #define CONFIG_EXTRA_ENV_SETTINGS               \
 378         "hwconfig=fsl_ddr:bank_intlv=auto\0"    \
 379         "ramdisk_addr=0x800000\0"               \
 380         "ramdisk_size=0x2000000\0"              \
 381         "fdt_high=0xa0000000\0"                 \
 382         "initrd_high=0xffffffffffffffff\0"      \
 383         "fdt_addr=0x64f00000\0"                 \
 384         "kernel_addr=0x65000000\0"              \
 385         "kernel_start=0x1000000\0"              \
 386         "kernelheader_start=0x800000\0"         \
 387         "scriptaddr=0x80000000\0"               \
 388         "scripthdraddr=0x80080000\0"            \
 389         "fdtheader_addr_r=0x80100000\0"         \
 390         "kernelheader_addr_r=0x80200000\0"      \
 391         "kernelheader_addr=0x580800000\0"       \
 392         "kernel_addr_r=0x81000000\0"            \
 393         "kernelheader_size=0x40000\0"           \
 394         "fdt_addr_r=0x90000000\0"               \
 395         "load_addr=0xa0000000\0"                \
 396         "kernel_size=0x2800000\0"               \
 397         "console=ttyAMA0,38400n8\0"             \
 398         MC_INIT_CMD                             \
 399         BOOTENV                                 \
 400         "boot_scripts=ls2088ardb_boot.scr\0"    \
 401         "boot_script_hdr=hdr_ls2088ardb_bs.out\0"       \
 402         "scan_dev_for_boot_part="               \
 403                 "part list ${devtype} ${devnum} devplist; "     \
 404                 "env exists devplist || setenv devplist 1; "    \
 405                 "for distro_bootpart in ${devplist}; do "       \
 406                         "if fstype ${devtype} "                 \
 407                                 "${devnum}:${distro_bootpart} " \
 408                                 "bootfstype; then "             \
 409                                 "run scan_dev_for_boot; "       \
 410                         "fi; "                                  \
 411                 "done\0"                                        \
 412         "scan_dev_for_boot="                                    \
 413                 "echo Scanning ${devtype} "                     \
 414                         "${devnum}:${distro_bootpart}...; "     \
 415                 "for prefix in ${boot_prefixes}; do "           \
 416                         "run scan_dev_for_scripts; "            \
 417                 "done;\0"                                       \
 418         "boot_a_script="                                        \
 419                 "load ${devtype} ${devnum}:${distro_bootpart} " \
 420                         "${scriptaddr} ${prefix}${script}; "    \
 421                 "env exists secureboot && load ${devtype} "     \
 422                         "${devnum}:${distro_bootpart} "         \
 423                         "${scripthdraddr} ${prefix}${boot_script_hdr} " \
 424                         "&& esbc_validate ${scripthdraddr};"    \
 425                 "source ${scriptaddr}\0"                        \
 426         "installer=load mmc 0:2 $load_addr "                    \
 427                 "/flex_installer_arm64.itb; "                   \
 428                 "bootm $load_addr#ls2088ardb\0"                 \
 429         "qspi_bootcmd=echo Trying load from qspi..;"            \
 430                 "sf probe && sf read $load_addr "               \
 431                 "$kernel_start $kernel_size ; env exists secureboot &&" \
 432                 "sf read $kernelheader_addr_r $kernelheader_start "     \
 433                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
 434                 " bootm $load_addr#$board\0"                    \
 435         "nor_bootcmd=echo Trying load from nor..;"              \
 436                 "cp.b $kernel_addr $load_addr "                 \
 437                 "$kernel_size ; env exists secureboot && "      \
 438                 "cp.b $kernelheader_addr $kernelheader_addr_r " \
 439                 "$kernelheader_size && esbc_validate ${kernelheader_addr_r}; "\
 440                 "bootm $load_addr#$board\0"
 441
 442 #undef CONFIG_BOOTCOMMAND
 443 #ifdef CONFIG_QSPI_BOOT
 444 /* Try to boot an on-QSPI kernel first, then do normal distro boot */
 445 #define CONFIG_BOOTCOMMAND                                              \
 446                         "env exists mcinitcmd && env exists secureboot "\
 447                         "&& esbc_validate 0x20780000; "                 \
 448                         "env exists mcinitcmd && "                      \
 449                         "fsl_mc lazyapply dpl 0x20d00000; "             \
 450                         "run distro_bootcmd;run qspi_bootcmd; "         \
 451                         "env exists secureboot && esbc_halt; "
 452 #else
 453 /* Try to boot an on-NOR kernel first, then do normal distro boot */
 454 #define CONFIG_BOOTCOMMAND                                              \
 455                         "env exists mcinitcmd && env exists secureboot "\
 456                         "&& esbc_validate 0x580780000; env exists mcinitcmd "\
 457                         "&& fsl_mc lazyapply dpl 0x580d00000;"          \
 458                         "run distro_bootcmd;run nor_bootcmd; "          \
 459                         "env exists secureboot && esbc_halt; "
 460 #endif
 461
 462 #undef CONFIG_BOOTARGS
 463 #define CONFIG_BOOTARGS         "console=ttyS1,115200 root=/dev/ram0 " \
 464                                 "earlycon=uart8250,mmio,0x21c0600 " \
 465                                 "ramdisk_size=0x2000000 default_hugepagesz=2m" \
 466                                 " hugepagesz=2m hugepages=256"
 467
 468 /* MAC/PHY configuration */
 469 #ifdef CONFIG_FSL_MC_ENET
 470 #define CONFIG_PHYLIB_10G
 471 #define CONFIG_PHY_AQUANTIA
 472 #define CONFIG_PHY_CORTINA
 473 #define CONFIG_PHYLIB
 474 #define CONFIG_SYS_CORTINA_FW_IN_NOR
 475 #ifdef CONFIG_QSPI_BOOT
 476 #define CONFIG_CORTINA_FW_ADDR          0x20980000
 477 #else
 478 #define CONFIG_CORTINA_FW_ADDR          0x580980000
 479 #endif
 480 #define CONFIG_CORTINA_FW_LENGTH        0x40000
 481
 482 #define CORTINA_PHY_ADDR1       0x10
 483 #define CORTINA_PHY_ADDR2       0x11
 484 #define CORTINA_PHY_ADDR3       0x12
 485 #define CORTINA_PHY_ADDR4       0x13
 486 #define AQ_PHY_ADDR1            0x00
 487 #define AQ_PHY_ADDR2            0x01
 488 #define AQ_PHY_ADDR3            0x02
 489 #define AQ_PHY_ADDR4            0x03
 490 #define AQR405_IRQ_MASK         0x36
 491
 492 #define CONFIG_MII
 493 #define CONFIG_ETHPRIME         "DPMAC1@xgmii"
 494 #define CONFIG_PHY_GIGE
 495 #define CONFIG_PHY_AQUANTIA
 496 #endif
 497
 498 #include <asm/fsl_secure_boot.h>
 499
 500 #endif /* __LS2_RDB_H */