* Global routines used for PIP405
*****************************************************************************/
+#ifndef __ASSEMBLY__
extern int mem_test(unsigned long start, unsigned long ramsize,int mode);
void user_led1(unsigned char on);
-#define PLD_BASE_ADDRESS CFG_ISA_IO_BASE_ADDRESS + 0x800
-#define PLD_PART_REG PLD_BASE_ADDRESS + 0
-#define PLD_VERS_REG PLD_BASE_ADDRESS + 1
+#define PLD_BASE_ADDRESS CONFIG_SYS_ISA_IO_BASE_ADDRESS + 0x800
+#define PLD_PART_REG PLD_BASE_ADDRESS + 0
+#define PLD_VERS_REG PLD_BASE_ADDRESS + 1
#define PLD_BOARD_CFG_REG PLD_BASE_ADDRESS + 2
#define PLD_LED_USER_REG PLD_BASE_ADDRESS + 3
#define PLD_SYS_MAN_REG PLD_BASE_ADDRESS + 4
#define PLD_FLASH_COM_REG PLD_BASE_ADDRESS + 5
-#define PLD_CAN_REG PLD_BASE_ADDRESS + 6
+#define PLD_CAN_REG PLD_BASE_ADDRESS + 6
#define PLD_SER_PWR_REG PLD_BASE_ADDRESS + 7
#define PLD_COM_PWR_REG PLD_BASE_ADDRESS + 8
#define PLD_NIC_VGA_REG PLD_BASE_ADDRESS + 9
#define PIIX4_VENDOR_ID 0x8086
#define PIIX4_IDE_DEV_ID 0x7111
+#endif
/* timings */
-/* PLD (CS7) */
-#define PLD_BME 0 /* Burst disable */
-#define PLD_TWE 5 /* 5 * 30ns 120ns Waitstates (access=TWT+1+TH) */
-#define PLD_CSN 1 /* Chipselect is driven inactive for 1 Cycle BTW transfers */
-#define PLD_OEN 1 /* Cycles from CS low to OE low */
-#define PLD_WBN 1 /* Cycles from CS low to WE low */
-#define PLD_WBF 1 /* Cycles from WE high to CS high */
-#define PLD_TH 2 /* Number of hold cycles after transfer */
-#define PLD_RE 0 /* Ready disabled */
-#define PLD_SOR 1 /* Sample on Ready disabled */
-#define PLD_BEM 0 /* Byte Write only active on Write cycles */
-#define PLD_PEN 0 /* Parity disable */
-#define PLD_AP ((PLD_BME << 31) + (PLD_TWE << 23) + (PLD_CSN << 18) + (PLD_OEN << 16) + (PLD_WBN << 14) + \
- (PLD_WBF << 12) + (PLD_TH << 9) + (PLD_RE << 8) + (PLD_SOR << 7) + (PLD_BEM << 6) + (PLD_PEN << 5))
-
-/* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */
-#define PLD_BS 0 /* 1 MByte */
-/* Usage: 0=disabled, 1=Read only, 2=Write Only, 3=R/W */
-#define PLD_BU 3 /* R/W */
-/* Bus width: 0=8Bit, 1=16Bit, 2=32Bit, 3=Reserved */
-#define PLD_BW 0 /* 16Bit */
-#define PLD_CR ((PER_PLD_ADDR & 0xfff00000) + (PLD_BS << 17) + (PLD_BU << 15) + (PLD_BW << 13))
-
-/* timings */
-
-#define PER_BOARD_ADDR (PER_UART1_ADDR+(1024*1024))
-/* Dummy CS to get the board revision */
-#define BOARD_BME 0 /* Burst disable */
-#define BOARD_TWE 255 /* 255 * 30ns 120ns Waitstates (access=TWT+1+TH) */
-#define BOARD_CSN 1 /* Chipselect is driven inactive for 1 Cycle BTW transfers */
-#define BOARD_OEN 1 /* Cycles from CS low to OE low */
-#define BOARD_WBN 1 /* Cycles from CS low to WE low */
-#define BOARD_WBF 1 /* Cycles from WE high to CS high */
-#define BOARD_TH 2 /* Number of hold cycles after transfer */
-#define BOARD_RE 0 /* Ready disabled */
-#define BOARD_SOR 1 /* Sample on Ready disabled */
-#define BOARD_BEM 0 /* Byte Write only active on Write cycles */
-#define BOARD_PEN 0 /* Parity disable */
-#define BOARD_AP ((BOARD_BME << 31) + (BOARD_TWE << 23) + (BOARD_CSN << 18) + (BOARD_OEN << 16) + (BOARD_WBN << 14) + \
- (BOARD_WBF << 12) + (BOARD_TH << 9) + (BOARD_RE << 8) + (BOARD_SOR << 7) + (BOARD_BEM << 6) + (BOARD_PEN << 5))
+/* CS Config register (CS7) */
+#define CONFIG_PORT_BME 0 /* Burst disable */
+#define CONFIG_PORT_TWE 255 /* 255 * 30ns 120ns Waitstates (access=TWT+1+TH) */
+#define CONFIG_PORT_CSN 1 /* Chipselect is driven inactive for 1 Cycle BTW transfers */
+#define CONFIG_PORT_OEN 1 /* Cycles from CS low to OE low */
+#define CONFIG_PORT_WBN 1 /* Cycles from CS low to WE low */
+#define CONFIG_PORT_WBF 1 /* Cycles from WE high to CS high */
+#define CONFIG_PORT_TH 2 /* Number of hold cycles after transfer */
+#define CONFIG_PORT_RE 0 /* Ready disabled */
+#define CONFIG_PORT_SOR 1 /* Sample on Ready disabled */
+#define CONFIG_PORT_BEM 0 /* Byte Write only active on Write cycles */
+#define CONFIG_PORT_PEN 0 /* Parity disable */
+#define CONFIG_PORT_AP ((CONFIG_PORT_BME << 31) + (CONFIG_PORT_TWE << 23) + (CONFIG_PORT_CSN << 18) + (CONFIG_PORT_OEN << 16) + (CONFIG_PORT_WBN << 14) + \
+ (CONFIG_PORT_WBF << 12) + (CONFIG_PORT_TH << 9) + (CONFIG_PORT_RE << 8) + (CONFIG_PORT_SOR << 7) + (CONFIG_PORT_BEM << 6) + (CONFIG_PORT_PEN << 5))
/* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */
-#define BOARD_BS 0 /* 1 MByte */
+#define CONFIG_PORT_BS 0 /* 1 MByte */
/* Usage: 0=disabled, 1=Read only, 2=Write Only, 3=R/W */
-#define BOARD_BU 3 /* R/W */
+#define CONFIG_PORT_BU 3 /* R/W */
/* Bus width: 0=8Bit, 1=16Bit, 2=32Bit, 3=Reserved */
-#define BOARD_BW 0 /* 16Bit */
-#define BOARD_CR ((PER_BOARD_ADDR & 0xfff00000) + (BOARD_BS << 17) + (BOARD_BU << 15) + (BOARD_BW << 13))
-
-
-/* UART0 CS2 */
-#define UART0_BME 0 /* Burst disable */
-#define UART0_TWE 7 /* 7 * 30ns 210ns Waitstates (access=TWT+1+TH) */
-#define UART0_CSN 1 /* Chipselect is driven inactive for 1 Cycle BTW transfers */
-#define UART0_OEN 1 /* Cycles from CS low to OE low */
-#define UART0_WBN 1 /* Cycles from CS low to WE low */
-#define UART0_WBF 1 /* Cycles from WE high to CS high */
-#define UART0_TH 2 /* Number of hold cycles after transfer */
-#define UART0_RE 0 /* Ready disabled */
-#define UART0_SOR 1 /* Sample on Ready disabled */
-#define UART0_BEM 0 /* Byte Write only active on Write cycles */
-#define UART0_PEN 0 /* Parity disable */
-#define UART0_AP ((UART0_BME << 31) + (UART0_TWE << 23) + (UART0_CSN << 18) + (UART0_OEN << 16) + (UART0_WBN << 14) + \
- (UART0_WBF << 12) + (UART0_TH << 9) + (UART0_RE << 8) + (UART0_SOR << 7) + (UART0_BEM << 6) + (UART0_PEN << 5))
-
-/* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */
-#define UART0_BS 0 /* 1 MByte */
-/* Usage: 0=disabled, 1=Read only, 2=Write Only, 3=R/W */
-#define UART0_BU 3 /* R/W */
-/* Bus width: 0=8Bit, 1=16Bit, 2=32Bit, 3=Reserved */
-#define UART0_BW 0 /* 8Bit */
-#define UART0_CR ((PER_UART0_ADDR & 0xfff00000) + (UART0_BS << 17) + (UART0_BU << 15) + (UART0_BW << 13))
-
-/* UART1 CS3 */
-#define UART1_AP UART0_AP /* same timing as UART0 */
-#define UART1_CR ((PER_UART1_ADDR & 0xfff00000) + (UART0_BS << 17) + (UART0_BU << 15) + (UART0_BW << 13))
-
+#define CONFIG_PORT_BW 0 /* 16Bit */
+#define CONFIG_PORT_CR ((CONFIG_PORT_ADDR & 0xfff00000) + (CONFIG_PORT_BS << 17) + (CONFIG_PORT_BU << 15) + (CONFIG_PORT_BW << 13))
/* Flash CS0 or CS 1 */
/* 0x7F8FFE80 slowest timing at all... */
-#define FLASH_BME_B 1 /* Burst enable */
+#define FLASH_BME_B 1 /* Burst enable */
#define FLASH_FWT_B 0x6 /* 6 * 30ns 210ns First Wait Access */
#define FLASH_BWT_B 0x6 /* 6 * 30ns 210ns Burst Wait Access */
-#define FLASH_BME 0 /* Burst disable */
+#define FLASH_BME 0 /* Burst disable */
#define FLASH_TWE 0xb/* 11 * 30ns 330ns Waitstates (access=TWT+1+TH) */
#define FLASH_CSN 0 /* Chipselect is driven inactive for 1 Cycle BTW transfers */
#define FLASH_OEN 1 /* Cycles from CS low to OE low */
#define FLASH_BEM 0 /* Byte Write only active on Write cycles */
#define FLASH_PEN 0 /* Parity disable */
/* Access Parameter Register for non Boot */
-#define FLASH_AP ((FLASH_BME << 31) + (FLASH_TWE << 23) + (FLASH_CSN << 18) + (FLASH_OEN << 16) + (FLASH_WBN << 14) + \
- (FLASH_WBF << 12) + (FLASH_TH << 9) + (FLASH_RE << 8) + (FLASH_SOR << 7) + (FLASH_BEM << 6) + (FLASH_PEN << 5))
+#define FLASH_AP ((FLASH_BME << 31) + (FLASH_TWE << 23) + (FLASH_CSN << 18) + (FLASH_OEN << 16) + (FLASH_WBN << 14) + \
+ (FLASH_WBF << 12) + (FLASH_TH << 9) + (FLASH_RE << 8) + (FLASH_SOR << 7) + (FLASH_BEM << 6) + (FLASH_PEN << 5))
/* Access Parameter Register for Boot */
-#define FLASH_AP_B ((FLASH_BME_B << 31) + (FLASH_FWT_B << 26) + (FLASH_BWT_B << 23) + (FLASH_CSN << 18) + (FLASH_OEN << 16) + (FLASH_WBN << 14) + \
- (FLASH_WBF << 12) + (FLASH_TH << 9) + (FLASH_RE << 8) + (FLASH_SOR << 7) + (FLASH_BEM << 6) + (FLASH_PEN << 5))
+#define FLASH_AP_B ((FLASH_BME_B << 31) + (FLASH_FWT_B << 26) + (FLASH_BWT_B << 23) + (FLASH_CSN << 18) + (FLASH_OEN << 16) + (FLASH_WBN << 14) + \
+ (FLASH_WBF << 12) + (FLASH_TH << 9) + (FLASH_RE << 8) + (FLASH_SOR << 7) + (FLASH_BEM << 6) + (FLASH_PEN << 5))
/* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */
-#define FLASH_BS 2 /* 4 MByte */
+#define FLASH_BS FLASH_SIZE_PRELIM /* 4 MByte */
/* Usage: 0=disabled, 1=Read only, 2=Write Only, 3=R/W */
#define FLASH_BU 3 /* R/W */
/* Bus width: 0=8Bit, 1=16Bit, 2=32Bit, 3=Reserved */
#define FLASH_BW 1 /* 16Bit */
/* CR register for Boot */
-#define FLASH_CR_B ((FLASH_BASE0_PRELIM & 0xfff00000) + (FLASH_BS << 17) + (FLASH_BU << 15) + (FLASH_BW << 13))
+#define FLASH_CR_B ((FLASH_BASE_PRELIM & 0xfff00000) + (FLASH_BS << 17) + (FLASH_BU << 15) + (FLASH_BW << 13))
/* CR register for non Boot */
#define FLASH_CR ((MULTI_PURPOSE_SOCKET_ADDR & 0xfff00000) + (FLASH_BS << 17) + (FLASH_BU << 15) + (FLASH_BW << 13))
/* MPS CS1 or CS0 */
/* Boot CS: */
-#define MPS_BME_B 1 /* Burst enable */
+#define MPS_BME_B 1 /* Burst enable */
#define MPS_FWT_B 0x6/* 6 * 30ns 210ns First Wait Access */
#define MPS_BWT_B 0x6 /* 6 * 30ns 210ns Burst Wait Access */
-#define MPS_BME 0 /* Burst disable */
+#define MPS_BME 0 /* Burst disable */
#define MPS_TWE 0xb/* 11 * 30ns 330ns Waitstates (access=TWT+1+TH) */
#define MPS_CSN 0 /* Chipselect is driven inactive for 1 Cycle BTW transfers */
#define MPS_OEN 1 /* Cycles from CS low to OE low */
#define MPS_BEM 0 /* Byte Write only active on Write cycles */
#define MPS_PEN 0 /* Parity disable */
/* Access Parameter Register for non Boot */
-#define MPS_AP ((MPS_BME << 31) + (MPS_TWE << 23) + (MPS_CSN << 18) + (MPS_OEN << 16) + (MPS_WBN << 14) + \
- (MPS_WBF << 12) + (MPS_TH << 9) + (MPS_RE << 8) + (MPS_SOR << 7) + (MPS_BEM << 6) + (MPS_PEN << 5))
+#define MPS_AP ((MPS_BME << 31) + (MPS_TWE << 23) + (MPS_CSN << 18) + (MPS_OEN << 16) + (MPS_WBN << 14) + \
+ (MPS_WBF << 12) + (MPS_TH << 9) + (MPS_RE << 8) + (MPS_SOR << 7) + (MPS_BEM << 6) + (MPS_PEN << 5))
/* Access Parameter Register for Boot */
-#define MPS_AP_B ((MPS_BME_B << 31) + (MPS_FWT_B << 26) + (MPS_BWT_B << 23) + (MPS_CSN << 18) + (MPS_OEN << 16) + (MPS_WBN << 14) + \
- (MPS_WBF << 12) + (MPS_TH << 9) + (MPS_RE << 8) + (MPS_SOR << 7) + (MPS_BEM << 6) + (MPS_PEN << 5))
+#define MPS_AP_B ((MPS_BME_B << 31) + (MPS_FWT_B << 26) + (MPS_BWT_B << 23) + (MPS_CSN << 18) + (MPS_OEN << 16) + (MPS_WBN << 14) + \
+ (MPS_WBF << 12) + (MPS_TH << 9) + (MPS_RE << 8) + (MPS_SOR << 7) + (MPS_BEM << 6) + (MPS_PEN << 5))
/* Size: 0=1MB, 1=2MB, 2=4MB, 3=8MB, 4=16MB, 5=32MB, 6=64MB, 7=128MB */
#define MPS_BS 2 /* 4 MByte */
+#define MPS_BS_B FLASH_SIZE_PRELIM /* 1 MByte */
/* Usage: 0=disabled, 1=Read only, 2=Write Only, 3=R/W */
#define MPS_BU 3 /* R/W */
/* Bus width: 0=8Bit, 1=16Bit, 2=32Bit, 3=Reserved */
#define MPS_BW 0 /* 8Bit */
/* CR register for Boot */
-#define MPS_CR_B ((FLASH_BASE0_PRELIM & 0xfff00000) + (MPS_BS << 17) + (MPS_BU << 15) + (MPS_BW << 13))
+#define MPS_CR_B ((FLASH_BASE_PRELIM & 0xfff00000) + (MPS_BS << 17) + (MPS_BU << 15) + (MPS_BW << 13))
/* CR register for non Boot */
#define MPS_CR ((MULTI_PURPOSE_SOCKET_ADDR & 0xfff00000) + (MPS_BS << 17) + (MPS_BU << 15) + (MPS_BW << 13))
projects / people / ms / u-boot.git / blobdiff