+#
+# Serial device configuration
+#
+
+menu "Serial drivers"
+
+config REQUIRE_SERIAL_CONSOLE
+ bool "Require a serial port for console"
+ # Running without a serial console is not supported by the
+ # non-dm serial code
+ depends on DM_SERIAL
+ default y
+ help
+ Require a serial port for the console, and panic if none is found
+ during serial port initialization (default y). Set this to n on
+ boards which have no debug serial port whatsoever.
+
config DM_SERIAL
bool "Enable Driver Model for serial drivers"
depends on DM
choice
prompt "Select which UART will provide the debug UART"
depends on DEBUG_UART
+ default DEBUG_UART_NS16550
+
+config DEBUG_UART_ALTERA_JTAGUART
+ bool "Altera JTAG UART"
+ help
+ Select this to enable a debug UART using the altera_jtag_uart driver.
+ You will need to provide parameters to make this work. The driver will
+ be available until the real driver model serial is running.
+
+config DEBUG_UART_ALTERA_UART
+ bool "Altera UART"
+ help
+ Select this to enable a debug UART using the altera_uart driver.
+ You will need to provide parameters to make this work. The driver will
+ be available until the real driver model serial is running.
config DEBUG_UART_NS16550
bool "ns16550"
will need to provide parameters to make this work. The driver will
be available until the real driver model serial is running.
+config DEBUG_EFI_CONSOLE
+ bool "EFI"
+ depends on EFI_APP
+ help
+ Select this to enable a debug console which calls back to EFI to
+ output to the console. This can be useful for early debugging of
+ U-Boot when running on top of EFI (Extensive Firmware Interface).
+ This is a type of BIOS used by PCs.
+
+config DEBUG_UART_S5P
+ bool "Samsung S5P"
+ help
+ Select this to enable a debug UART using the serial_s5p driver. You
+ will need to provide parameters to make this work. The driver will
+ be available until the real driver-model serial is running.
+
+config DEBUG_UART_ZYNQ
+ bool "Xilinx Zynq"
+ help
+ Select this to enable a debug UART using the serial_s5p driver. You
+ will need to provide parameters to make this work. The driver will
+ be available until the real driver-model serial is running.
+
+config DEBUG_UART_APBUART
+ depends on LEON3
+ bool "Gaisler APBUART"
+ help
+ Select this to enable a debug UART using the serial_leon3 driver. You
+ will need to provide parameters to make this work. The driver will
+ be available until the real driver model serial is running.
+
endchoice
config DEBUG_UART_BASE
value. Use this value to specify the shift to use, where 0=byte
registers, 2=32-bit word registers, etc.
+config DEBUG_UART_BOARD_INIT
+ bool "Enable board-specific debug UART init"
+ depends on DEBUG_UART
+ help
+ Some boards need to set things up before the debug UART can be used.
+ On these boards a call to debug_uart_init() is insufficient. When
+ this option is enabled, the function board_debug_uart_init() will
+ be called when debug_uart_init() is called. You can put any code
+ here that is needed to set up the UART ready for use, such as set
+ pin multiplexing or enable clocks.
+
+config DEBUG_UART_ANNOUNCE
+ bool "Show a message when the debug UART starts up"
+ depends on DEBUG_UART
+ help
+ Enable this option to show a message when the debug UART is ready
+ for use. You will see a message like "<debug_uart> " as soon as
+ U-Boot has the UART ready for use (i.e. your code calls
+ debug_uart_init()). This can be useful just as a check that
+ everything is working.
+
+config ALTERA_JTAG_UART
+ bool "Altera JTAG UART support"
+ depends on DM_SERIAL
+ help
+ Select this to enable an JTAG UART for Altera devices.The JTAG UART
+ core implements a method to communicate serial character streams
+ between a host PC and a Qsys system on an Altera FPGA. Please find
+ details on the "Embedded Peripherals IP User Guide" of Altera.
+
+config ALTERA_JTAG_UART_BYPASS
+ bool "Bypass output when no connection"
+ depends on ALTERA_JTAG_UART
+ help
+ Bypass console output and keep going even if there is no JTAG
+ terminal connection with the host. The console output will resume
+ once the JTAG terminal is connected. Without the bypass, the console
+ output will wait forever until a JTAG terminal is connected. If you
+ not are sure, say Y.
+
+config ALTERA_UART
+ bool "Altera UART support"
+ depends on DM_SERIAL
+ help
+ Select this to enable an UART for Altera devices. Please find
+ details on the "Embedded Peripherals IP User Guide" of Altera.
+
+config SYS_NS16550
+ bool "NS16550 UART or compatible"
+ help
+ Support NS16550 UART or compatible. This can be enabled in the
+ device tree with the correct input clock frequency. If the input
+ clock frequency is not defined in the device tree, the macro
+ CONFIG_SYS_NS16550_CLK defined in a legacy board header file will
+ be used. It can be a constant or a function to get clock, eg,
+ get_serial_clock().
+
+config SANDBOX_SERIAL
+ bool "Sandbox UART support"
+ depends on SANDBOX
+ help
+ Select this to enable a seral UART for sandbox. This is required to
+ operate correctly, otherwise you will see no serial output from
+ sandbox. The emulated UART will display to the console and console
+ input will be fed into the UART. This allows you to interact with
+ U-Boot.
+
+ The operation of the console is controlled by the -t command-line
+ flag. In raw mode, U-Boot sees all characters from the terminal
+ before they are processed, including Ctrl-C. In cooked mode, Ctrl-C
+ is processed by the terminal, and terminates U-Boot. Valid options
+ are:
+
+ -t raw-with-sigs Raw mode, Ctrl-C will terminate U-Boot
+ -t raw Raw mode, Ctrl-C is processed by U-Boot
+ -t cooked Cooked mode, Ctrl-C terminates
+
config UNIPHIER_SERIAL
- bool "UniPhier on-chip UART support"
- depends on ARCH_UNIPHIER && DM_SERIAL
+ bool "Support for UniPhier on-chip UART"
+ depends on ARCH_UNIPHIER
help
- Support for the on-chip UARTs on the Panasonic UniPhier platform.
+ If you have a UniPhier based board and want to use the on-chip
+ serial ports, say Y to this option. If unsure, say N.
+
+endmenu