include/configs: drop default definitions of CONFIG_SYS_MAXARGS

[people/ms/u-boot.git] / include / configs / highbank.h

diff --git a/include/configs/highbank.h b/include/configs/highbank.h
index afb6e64e1b0464c6d9ec521a8b701e1711b766aa..b2b2c2500aff5f0b4860906a46952cb9412e09f4 100644 (file)
--- a/include/configs/highbank.h
+++ b/include/configs/highbank.h
@@ -7,20 +7,16 @@
 #ifndef __CONFIG_H
 #define __CONFIG_H
 
-#define CONFIG_SYS_DCACHE_OFF
-#define CONFIG_L2_OFF
-#define CONFIG_SYS_THUMB_BUILD
+#include <config_distro_defaults.h>
 
-#define CONFIG_SYS_NO_FLASH
-#define CFG_HZ                         1000
-#define CONFIG_SYS_HZ                  CFG_HZ
+#define CONFIG_SYS_DCACHE_OFF
 
-#define CONFIG_OF_LIBFDT
-#define CONFIG_OF_BOARD_SETUP
-#define CONFIG_FIT
-#define CONFIG_SUPPORT_RAW_INITRD
 #define CONFIG_SYS_BOOTMAPSZ           (16 << 20)
 
+#define CONFIG_SYS_TIMER_RATE          (150000000/256)
+#define CONFIG_SYS_TIMER_COUNTER       (0xFFF34000 + 0x4)
+#define CONFIG_SYS_TIMER_COUNTS_DOWN
+
 /*
  * Size of malloc() pool
  */
@@ -31,8 +27,6 @@
 #define CONFIG_PL01x_PORTS             { (void *)(0xFFF36000) }
 #define CONFIG_CONS_INDEX              0
 
-#define CONFIG_BAUDRATE                        115200
-
 #define CONFIG_BOOTCOUNT_LIMIT
 #define CONFIG_SYS_BOOTCOUNT_SINGLEWORD
 #define CONFIG_SYS_BOOTCOUNT_LE                /* Use little-endian accessors */
@@ -47,70 +41,35 @@
 #define CONFIG_SYS_SCSI_MAX_DEVICE     (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
                                        CONFIG_SYS_SCSI_MAX_LUN)
 
-#define CONFIG_DOS_PARTITION
-#define CONFIG_EFI_PARTITION
-
 #define CONFIG_CALXEDA_XGMAC
 
-/* PXE support */
-#define CONFIG_BOOTP_PXE
-#define CONFIG_BOOTP_PXE_CLIENTARCH    0x100
-#define CONFIG_BOOTP_VCI_STRING                "U-boot.armv7.highbank"
-
 /*
  * Command line configuration.
  */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_BDI
-#define CONFIG_CMD_BOOTZ
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_MEMORY
-#define CONFIG_CMD_LOADS
-#define CONFIG_CMD_SCSI
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_EXT4
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_PXE
-#define CONFIG_MENU
-
-#define CONFIG_BOOTDELAY               2
+
 #define CONFIG_BOOT_RETRY_TIME         -1
 #define CONFIG_RESET_TO_RETRY
-#define CONFIG_AUTOBOOT_KEYED
-#define CONFIG_AUTOBOOT_PROMPT "Autobooting in %d seconds...\nPress <s> to stop or <d> to delay\n", bootdelay
 
 /*
  * Miscellaneous configurable options
  */
-#define CONFIG_CMDLINE_EDITING
-#define CONFIG_AUTO_COMPLETE
-#define CONFIG_SYS_LONGHELP            /* undef to save memory          */
 #define CONFIG_SYS_CBSIZE              1024    /* Console I/O Buffer Size */
-#define CONFIG_SYS_MAXARGS             16      /* max number of cmd args */
 #define CONFIG_SYS_BARGSIZE            CONFIG_SYS_CBSIZE
-#define CONFIG_SYS_PROMPT              "Highbank #"
-#define CONFIG_SYS_HUSH_PARSER
-/* Print Buffer Size */
-#define CONFIG_SYS_PBSIZE              (CONFIG_SYS_CBSIZE + \
-                                        sizeof(CONFIG_SYS_PROMPT)+16)
 
 #define CONFIG_SYS_LOAD_ADDR           0x800000
 #define CONFIG_SYS_64BIT_LBA
 
-
 /*-----------------------------------------------------------------------
  * Physical Memory Map
+ * The DRAM is already setup, so do not touch the DT node later.
  */
-#define CONFIG_NR_DRAM_BANKS           1
+#define CONFIG_NR_DRAM_BANKS           0
 #define PHYS_SDRAM_1_SIZE              (4089 << 20)
 #define CONFIG_SYS_MEMTEST_START       0x100000
 #define CONFIG_SYS_MEMTEST_END         (PHYS_SDRAM_1_SIZE - 0x100000)
 
 /* Environment data setup
 */
-#define CONFIG_ENV_IS_IN_NVRAM
 #define CONFIG_SYS_NVRAM_BASE_ADDR     0xfff88000      /* NVRAM base address */
 #define CONFIG_SYS_NVRAM_SIZE          0x8000          /* NVRAM size */
 #define CONFIG_ENV_SIZE                        0x2000          /* Size of Environ */