#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
+/* Partitions */
+#define CONFIG_DOS_PARTITION
+
/*
* Supported commands
*/
#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
+ CFG_CMD_DATE | \
+ CFG_CMD_DISPLAY | \
CFG_CMD_DHCP | \
+ CFG_CMD_EEPROM | \
+ CFG_CMD_I2C | \
+ CFG_CMD_IDE | \
CFG_CMD_NFS | \
- CFG_CMD_SNTP)
+ CFG_CMD_PCI | \
+ CFG_CMD_SNTP )
/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
#include <cmd_confdefs.h>
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
- "nfsroot=$(serverip):$(rootpath)\0" \
+ "nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
- "addip=setenv bootargs $(bootargs) " \
- "ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask)" \
- ":$(hostname):$(netdev):off panic=1\0" \
+ "addip=setenv bootargs ${bootargs} " \
+ "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
+ ":${hostname}:${netdev}:off panic=1\0" \
"flash_nfs=run nfsargs addip;" \
- "bootm $(kernel_addr)\0" \
- "net_nfs=tftp 200000 $(bootfile);run nfsargs addip;bootm\0" \
+ "bootm ${kernel_addr}\0" \
+ "net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
"rootpath=/opt/eldk/ppc_82xx\0" \
""
#define CONFIG_BOOTCOMMAND "run net_nfs"
+#define CONFIG_MISC_INIT_R 1
+
/*
* IPB Bus clocking configuration.
*/
-#undef CFG_IPBSPEED_133 /* define for 133MHz speed */
+#undef CFG_IPBCLK_EQUALS_XLBCLK /* define for 133MHz speed */
+
+/*
+ * I2C configuration
+ */
+#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
+#define CFG_I2C_MODULE 2 /* Select I2C module #1 or #2 */
+
+#define CFG_I2C_SPEED 100000 /* 100 kHz */
+#define CFG_I2C_SLAVE 0x7F
+
+/*
+ * EEPROM configuration
+ */
+#define CFG_I2C_EEPROM_ADDR 0x58
+#define CFG_I2C_EEPROM_ADDR_LEN 1
+#define CFG_EEPROM_PAGE_WRITE_BITS 4
+#define CFG_EEPROM_PAGE_WRITE_DELAY_MS 10
+
+/*
+ * RTC configuration
+ */
+#define CONFIG_RTC_PCF8563
+#define CFG_I2C_RTC_ADDR 0x51
/*
* Flash configuration
#define CFG_FLASH_CFI
#define CFG_FLASH_EMPTY_INFO
#define CFG_FLASH_CFI_AMD_RESET
-#define CFG_FLASH_PROTECTION
/*
* Environment settings
#define CFG_ENV_IS_IN_FLASH 1
#define CFG_ENV_SIZE 0x4000
#define CFG_ENV_SECT_SIZE 0x20000
+#define CFG_ENV_OFFSET_REDUND (CFG_ENV_OFFSET+CFG_ENV_SECT_SIZE)
+#define CFG_ENV_SIZE_REDUND (CFG_ENV_SIZE)
/*
* Memory map
#define CFG_MBAR 0xF0000000
#define CFG_SDRAM_BASE 0x00000000
#define CFG_DEFAULT_MBAR 0x80000000
+#define CFG_DISPLAY_BASE 0x80600000
+#define CFG_STATUS1_BASE 0x80600200
+#define CFG_STATUS2_BASE 0x80600300
/* Settings for XLB = 132 MHz */
#define SDRAM_DDR 1
#endif
#define CFG_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
-#define CFG_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
+#define CFG_MALLOC_LEN (512 << 10) /* Reserve 128 kB for malloc() */
#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*
*/
#define CONFIG_MPC5xxx_FEC 1
#define CONFIG_PHY_ADDR 0x00
+#define CONFIG_MII 1 /* MII PHY management */
/*
* GPIO configuration
*/
#define CFG_GPS_PORT_CONFIG 0x01051004
-/*
- * RTC configuration
- */
-#define CONFIG_RTC_MPC5200 1 /* use internal MPC5200 RTC */
-
/*
* Miscellaneous configurable options
*/
/* Display H1, Status Inputs, EPLD @0x80600000 */
#define CFG_CS3_START 0x80600000
-#define CFG_CS3_SIZE 0x00000210
-#define CFG_CS3_CFG 0x9800
+#define CFG_CS3_SIZE 0x00100000
+#define CFG_CS3_CFG 0x00019800
#define CFG_CS_BURST 0x00000000
#define CFG_CS_DEADCYCLE 0x33333333
+/*-----------------------------------------------------------------------
+ * IDE/ATA stuff Supports IDE harddisk
+ *-----------------------------------------------------------------------
+ */
+
+#undef CONFIG_IDE_8xx_PCCARD /* Use IDE with PC Card Adapter */
+
+#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
+#undef CONFIG_IDE_LED /* LED for ide not supported */
+
+#define CFG_IDE_MAXBUS 1 /* max. 1 IDE bus */
+#define CFG_IDE_MAXDEVICE 2 /* max. 2 drives per IDE bus */
+
+#define CONFIG_IDE_PREINIT 1
+
+#define CFG_ATA_IDE0_OFFSET 0x0000
+
+#define CFG_ATA_BASE_ADDR MPC5XXX_ATA
+
+/* Offset for data I/O */
+#define CFG_ATA_DATA_OFFSET (0x0060)
+
+/* Offset for normal register accesses */
+#define CFG_ATA_REG_OFFSET (CFG_ATA_DATA_OFFSET)
+
+/* Offset for alternate registers */
+#define CFG_ATA_ALT_OFFSET (0x005C)
+
+/* Interval between registers */
+#define CFG_ATA_STRIDE 4
+
+#define CONFIG_ATAPI 1
+
+#define CONFIG_VIDEO_SMI_LYNXEM
+#define CONFIG_CFB_CONSOLE
+#define CONFIG_VGA_AS_SINGLE_DEVICE
+#define CONFIG_VIDEO_LOGO
+
+/*
+ * PCI Mapping:
+ * 0x40000000 - 0x4fffffff - PCI Memory
+ * 0x50000000 - 0x50ffffff - PCI IO Space
+ */
+#define CONFIG_PCI 1
+#define CONFIG_PCI_PNP 1
+#define CONFIG_PCI_SCAN_SHOW 1
+
+#define CONFIG_PCI_MEM_BUS 0x40000000
+#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
+#define CONFIG_PCI_MEM_SIZE 0x10000000
+
+#define CONFIG_PCI_IO_BUS 0x50000000
+#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
+#define CONFIG_PCI_IO_SIZE 0x01000000
+
+#define CFG_ISA_IO CONFIG_PCI_IO_BUS
+
+/*---------------------------------------------------------------------*/
+/* Display addresses */
+/*---------------------------------------------------------------------*/
+
+#define CFG_DISP_CHR_RAM (CFG_DISPLAY_BASE + 0x38)
+#define CFG_DISP_CWORD (CFG_DISPLAY_BASE + 0x30)
+
#endif /* __CONFIG_H */
projects / people / ms / u-boot.git / blobdiff