--- /dev/null
+###############################################################################
+#
+# snmpd.conf:
+# An example configuration file for configuring the ucd-snmp snmpd agent.
+#
+###############################################################################
+#
+# This file is intended to only be as a starting point. Many more
+# configuration directives exist than are mentioned in this file. For
+# full details, see the snmpd.conf(5) manual page.
+#
+# All lines beginning with a '#' are comments and are intended for you
+# to read. All other lines are configuration commands for the agent.
+
+###############################################################################
+# Access Control
+###############################################################################
+
+# As shipped, the snmpd demon will only respond to queries on the
+# system mib group until this file is replaced or modified for
+# security purposes. Examples are shown below about how to increase the
+# level of access.
+
+# By far, the most common question I get about the agent is "why won't
+# it work?", when really it should be "how do I configure the agent to
+# allow me to access it?"
+#
+# By default, the agent responds to the "public" community for read
+# only access, if run out of the box without any configuration file in
+# place. The following examples show you other ways of configuring
+# the agent so that you can change the community names, and give
+# yourself write access to the mib tree as well.
+#
+# For more information, read the FAQ as well as the snmpd.conf(5)
+# manual page.
+
+####
+# First, map the community name "public" into a "security name"
+
+# sec.name source community
+com2sec notConfigUser default public
+
+####
+# Second, map the security name into a group name:
+
+# groupName securityModel securityName
+group notConfigGroup v1 notConfigUser
+group notConfigGroup v2c notConfigUser
+
+####
+# Third, create a view for us to let the group have rights to:
+
+# Make at least snmpwalk -v 1 localhost -c public system fast again.
+# name incl/excl subtree mask(optional)
+view systemview included .1.3.6.1.2.1.1
+view systemview included .1.3.6.1.2.1.25.1.1
+
+####
+# Finally, grant the group read-only access to the systemview view.
+
+# group context sec.model sec.level prefix read write notif
+access notConfigGroup "" any noauth exact systemview none none
+
+# -----------------------------------------------------------------------------
+
+# Here is a commented out example configuration that allows less
+# restrictive access.
+
+# YOU SHOULD CHANGE THE "COMMUNITY" TOKEN BELOW TO A NEW KEYWORD ONLY
+# KNOWN AT YOUR SITE. YOU *MUST* CHANGE THE NETWORK TOKEN BELOW TO
+# SOMETHING REFLECTING YOUR LOCAL NETWORK ADDRESS SPACE.
+
+## sec.name source community
+#com2sec local localhost COMMUNITY
+#com2sec mynetwork NETWORK/24 COMMUNITY
+
+## group.name sec.model sec.name
+#group MyRWGroup any local
+#group MyROGroup any mynetwork
+#
+#group MyRWGroup any otherv3user
+#...
+
+## incl/excl subtree mask
+#view all included .1 80
+
+## -or just the mib2 tree-
+
+#view mib2 included .iso.org.dod.internet.mgmt.mib-2 fc
+
+
+## context sec.model sec.level prefix read write notif
+#access MyROGroup "" any noauth 0 all none none
+#access MyRWGroup "" any noauth 0 all all all
+
+
+###############################################################################
+# Sample configuration to make net-snmpd RFC 1213.
+# Unfortunately v1 and v2c don't allow any user based authentification, so
+# opening up the default config is not an option from a security point.
+#
+# WARNING: If you uncomment the following lines you allow write access to your
+# snmpd daemon from any source! To avoid this use different names for your
+# community or split out the write access to a different community and
+# restrict it to your local network.
+# Also remember to comment the syslocation and syscontact parameters later as
+# otherwise they are still read only (see FAQ for net-snmp).
+#
+
+# First, map the community name "public" into a "security name"
+# sec.name source community
+#com2sec notConfigUser default public
+
+# Second, map the security name into a group name:
+# groupName securityModel securityName
+#group notConfigGroup v1 notConfigUser
+#group notConfigGroup v2c notConfigUser
+
+# Third, create a view for us to let the group have rights to:
+# Open up the whole tree for ro, make the RFC 1213 required ones rw.
+# name incl/excl subtree mask(optional)
+#view roview included .1
+#view rwview included system.sysContact
+#view rwview included system.sysName
+#view rwview included system.sysLocation
+#view rwview included interfaces.ifTable.ifEntry.ifAdminStatus
+#view rwview included at.atTable.atEntry.atPhysAddress
+#view rwview included at.atTable.atEntry.atNetAddress
+#view rwview included ip.ipForwarding
+#view rwview included ip.ipDefaultTTL
+#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteDest
+#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteIfIndex
+#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteMetric1
+#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteMetric2
+#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteMetric3
+#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteMetric4
+#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteType
+#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteAge
+#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteMask
+#view rwview included ip.ipRouteTable.ipRouteEntry.ipRouteMetric5
+#view rwview included ip.ipNetToMediaTable.ipNetToMediaEntry.ipNetToMediaIfIndex
+#view rwview included ip.ipNetToMediaTable.ipNetToMediaEntry.ipNetToMediaPhysAddress
+#view rwview included ip.ipNetToMediaTable.ipNetToMediaEntry.ipNetToMediaNetAddress
+#view rwview included ip.ipNetToMediaTable.ipNetToMediaEntry.ipNetToMediaType
+#view rwview included tcp.tcpConnTable.tcpConnEntry.tcpConnState
+#view rwview included egp.egpNeighTable.egpNeighEntry.egpNeighEventTrigger
+#view rwview included snmp.snmpEnableAuthenTraps
+
+# Finally, grant the group read-only access to the systemview view.
+# group context sec.model sec.level prefix read write notif
+#access notConfigGroup "" any noauth exact roview rwview none
+
+
+
+###############################################################################
+# System contact information
+#
+
+# It is also possible to set the sysContact and sysLocation system
+# variables through the snmpd.conf file:
+
+syslocation Unknown (edit /etc/snmp/snmpd.conf)
+syscontact Root <root@localhost> (configure /etc/snmp/snmp.local.conf)
+
+# Example output of snmpwalk:
+# % snmpwalk -v 1 localhost -c public system
+# system.sysDescr.0 = "SunOS name sun4c"
+# system.sysObjectID.0 = OID: enterprises.ucdavis.ucdSnmpAgent.sunos4
+# system.sysUpTime.0 = Timeticks: (595637548) 68 days, 22:32:55
+# system.sysContact.0 = "Me <me@somewhere.org>"
+# system.sysName.0 = "name"
+# system.sysLocation.0 = "Right here, right now."
+# system.sysServices.0 = 72
+
+
+###############################################################################
+# Logging
+#
+
+# We do not want annoying "Connection from UDP: " messages in syslog.
+# If the following option is commented out, snmpd will print each incoming
+# connection, which can be useful for debugging.
+
+dontLogTCPWrappersConnects yes
+
+# -----------------------------------------------------------------------------
+
+
+###############################################################################
+# Process checks.
+#
+# The following are examples of how to use the agent to check for
+# processes running on the host. The syntax looks something like:
+#
+# proc NAME [MAX=0] [MIN=0]
+#
+# NAME: the name of the process to check for. It must match
+# exactly (ie, http will not find httpd processes).
+# MAX: the maximum number allowed to be running. Defaults to 0.
+# MIN: the minimum number to be running. Defaults to 0.
+
+#
+# Examples (commented out by default):
+#
+
+# Make sure mountd is running
+#proc mountd
+
+# Make sure there are no more than 4 ntalkds running, but 0 is ok too.
+#proc ntalkd 4
+
+# Make sure at least one sendmail, but less than or equal to 10 are running.
+#proc sendmail 10 1
+
+# A snmpwalk of the process mib tree would look something like this:
+#
+# % snmpwalk -v 1 localhost -c public .1.3.6.1.4.1.2021.2
+# enterprises.ucdavis.procTable.prEntry.prIndex.1 = 1
+# enterprises.ucdavis.procTable.prEntry.prIndex.2 = 2
+# enterprises.ucdavis.procTable.prEntry.prIndex.3 = 3
+# enterprises.ucdavis.procTable.prEntry.prNames.1 = "mountd"
+# enterprises.ucdavis.procTable.prEntry.prNames.2 = "ntalkd"
+# enterprises.ucdavis.procTable.prEntry.prNames.3 = "sendmail"
+# enterprises.ucdavis.procTable.prEntry.prMin.1 = 0
+# enterprises.ucdavis.procTable.prEntry.prMin.2 = 0
+# enterprises.ucdavis.procTable.prEntry.prMin.3 = 1
+# enterprises.ucdavis.procTable.prEntry.prMax.1 = 0
+# enterprises.ucdavis.procTable.prEntry.prMax.2 = 4
+# enterprises.ucdavis.procTable.prEntry.prMax.3 = 10
+# enterprises.ucdavis.procTable.prEntry.prCount.1 = 0
+# enterprises.ucdavis.procTable.prEntry.prCount.2 = 0
+# enterprises.ucdavis.procTable.prEntry.prCount.3 = 1
+# enterprises.ucdavis.procTable.prEntry.prErrorFlag.1 = 1
+# enterprises.ucdavis.procTable.prEntry.prErrorFlag.2 = 0
+# enterprises.ucdavis.procTable.prEntry.prErrorFlag.3 = 0
+# enterprises.ucdavis.procTable.prEntry.prErrMessage.1 = "No mountd process running."
+# enterprises.ucdavis.procTable.prEntry.prErrMessage.2 = ""
+# enterprises.ucdavis.procTable.prEntry.prErrMessage.3 = ""
+# enterprises.ucdavis.procTable.prEntry.prErrFix.1 = 0
+# enterprises.ucdavis.procTable.prEntry.prErrFix.2 = 0
+# enterprises.ucdavis.procTable.prEntry.prErrFix.3 = 0
+#
+# Note that the errorFlag for mountd is set to 1 because one is not
+# running (in this case an rpc.mountd is, but thats not good enough),
+# and the ErrMessage tells you what's wrong. The configuration
+# imposed in the snmpd.conf file is also shown.
+#
+# Special Case: When the min and max numbers are both 0, it assumes
+# you want a max of infinity and a min of 1.
+#
+
+
+# -----------------------------------------------------------------------------
+
+
+###############################################################################
+# Executables/scripts
+#
+
+#
+# You can also have programs run by the agent that return a single
+# line of output and an exit code. Here are two examples.
+#
+# exec NAME PROGRAM [ARGS ...]
+#
+# NAME: A generic name. The name must be unique for each exec statement.
+# PROGRAM: The program to run. Include the path!
+# ARGS: optional arguments to be passed to the program
+
+# a simple hello world
+
+#exec echotest /bin/echo hello world
+
+# Run a shell script containing:
+#
+# #!/bin/sh
+# echo hello world
+# echo hi there
+# exit 35
+#
+# Note: this has been specifically commented out to prevent
+# accidental security holes due to someone else on your system writing
+# a /tmp/shtest before you do. Uncomment to use it.
+#
+#exec shelltest /bin/sh /tmp/shtest
+
+# Then,
+# % snmpwalk -v 1 localhost -c public .1.3.6.1.4.1.2021.8
+# enterprises.ucdavis.extTable.extEntry.extIndex.1 = 1
+# enterprises.ucdavis.extTable.extEntry.extIndex.2 = 2
+# enterprises.ucdavis.extTable.extEntry.extNames.1 = "echotest"
+# enterprises.ucdavis.extTable.extEntry.extNames.2 = "shelltest"
+# enterprises.ucdavis.extTable.extEntry.extCommand.1 = "/bin/echo hello world"
+# enterprises.ucdavis.extTable.extEntry.extCommand.2 = "/bin/sh /tmp/shtest"
+# enterprises.ucdavis.extTable.extEntry.extResult.1 = 0
+# enterprises.ucdavis.extTable.extEntry.extResult.2 = 35
+# enterprises.ucdavis.extTable.extEntry.extOutput.1 = "hello world."
+# enterprises.ucdavis.extTable.extEntry.extOutput.2 = "hello world."
+# enterprises.ucdavis.extTable.extEntry.extErrFix.1 = 0
+# enterprises.ucdavis.extTable.extEntry.extErrFix.2 = 0
+
+# Note that the second line of the /tmp/shtest shell script is cut
+# off. Also note that the exit status of 35 was returned.
+
+# -----------------------------------------------------------------------------
+
+
+###############################################################################
+# disk checks
+#
+
+# The agent can check the amount of available disk space, and make
+# sure it is above a set limit.
+
+# disk PATH [MIN=100000]
+#
+# PATH: mount path to the disk in question.
+# MIN: Disks with space below this value will have the Mib's errorFlag set.
+# Default value = 100000.
+
+# Check the / partition and make sure it contains at least 10 megs.
+
+#disk / 10000
+
+# % snmpwalk -v 1 localhost -c public .1.3.6.1.4.1.2021.9
+# enterprises.ucdavis.diskTable.dskEntry.diskIndex.1 = 0
+# enterprises.ucdavis.diskTable.dskEntry.diskPath.1 = "/" Hex: 2F
+# enterprises.ucdavis.diskTable.dskEntry.diskDevice.1 = "/dev/dsk/c201d6s0"
+# enterprises.ucdavis.diskTable.dskEntry.diskMinimum.1 = 10000
+# enterprises.ucdavis.diskTable.dskEntry.diskTotal.1 = 837130
+# enterprises.ucdavis.diskTable.dskEntry.diskAvail.1 = 316325
+# enterprises.ucdavis.diskTable.dskEntry.diskUsed.1 = 437092
+# enterprises.ucdavis.diskTable.dskEntry.diskPercent.1 = 58
+# enterprises.ucdavis.diskTable.dskEntry.diskErrorFlag.1 = 0
+# enterprises.ucdavis.diskTable.dskEntry.diskErrorMsg.1 = ""
+
+# -----------------------------------------------------------------------------
+
+
+###############################################################################
+# load average checks
+#
+
+# load [1MAX=12.0] [5MAX=12.0] [15MAX=12.0]
+#
+# 1MAX: If the 1 minute load average is above this limit at query
+# time, the errorFlag will be set.
+# 5MAX: Similar, but for 5 min average.
+# 15MAX: Similar, but for 15 min average.
+
+# Check for loads:
+#load 12 14 14
+
+# % snmpwalk -v 1 localhost -c public .1.3.6.1.4.1.2021.10
+# enterprises.ucdavis.loadTable.laEntry.loadaveIndex.1 = 1
+# enterprises.ucdavis.loadTable.laEntry.loadaveIndex.2 = 2
+# enterprises.ucdavis.loadTable.laEntry.loadaveIndex.3 = 3
+# enterprises.ucdavis.loadTable.laEntry.loadaveNames.1 = "Load-1"
+# enterprises.ucdavis.loadTable.laEntry.loadaveNames.2 = "Load-5"
+# enterprises.ucdavis.loadTable.laEntry.loadaveNames.3 = "Load-15"
+# enterprises.ucdavis.loadTable.laEntry.loadaveLoad.1 = "0.49" Hex: 30 2E 34 39
+# enterprises.ucdavis.loadTable.laEntry.loadaveLoad.2 = "0.31" Hex: 30 2E 33 31
+# enterprises.ucdavis.loadTable.laEntry.loadaveLoad.3 = "0.26" Hex: 30 2E 32 36
+# enterprises.ucdavis.loadTable.laEntry.loadaveConfig.1 = "12.00"
+# enterprises.ucdavis.loadTable.laEntry.loadaveConfig.2 = "14.00"
+# enterprises.ucdavis.loadTable.laEntry.loadaveConfig.3 = "14.00"
+# enterprises.ucdavis.loadTable.laEntry.loadaveErrorFlag.1 = 0
+# enterprises.ucdavis.loadTable.laEntry.loadaveErrorFlag.2 = 0
+# enterprises.ucdavis.loadTable.laEntry.loadaveErrorFlag.3 = 0
+# enterprises.ucdavis.loadTable.laEntry.loadaveErrMessage.1 = ""
+# enterprises.ucdavis.loadTable.laEntry.loadaveErrMessage.2 = ""
+# enterprises.ucdavis.loadTable.laEntry.loadaveErrMessage.3 = ""
+
+# -----------------------------------------------------------------------------
+
+
+###############################################################################
+# Extensible sections.
+#
+
+# This alleviates the multiple line output problem found in the
+# previous executable mib by placing each mib in its own mib table:
+
+# Run a shell script containing:
+#
+# #!/bin/sh
+# echo hello world
+# echo hi there
+# exit 35
+#
+# Note: this has been specifically commented out to prevent
+# accidental security holes due to someone else on your system writing
+# a /tmp/shtest before you do. Uncomment to use it.
+#
+# exec .1.3.6.1.4.1.2021.50 shelltest /bin/sh /tmp/shtest
+
+# % snmpwalk -v 1 localhost -c public .1.3.6.1.4.1.2021.50
+# enterprises.ucdavis.50.1.1 = 1
+# enterprises.ucdavis.50.2.1 = "shelltest"
+# enterprises.ucdavis.50.3.1 = "/bin/sh /tmp/shtest"
+# enterprises.ucdavis.50.100.1 = 35
+# enterprises.ucdavis.50.101.1 = "hello world."
+# enterprises.ucdavis.50.101.2 = "hi there."
+# enterprises.ucdavis.50.102.1 = 0
+
+# Now the Output has grown to two lines, and we can see the 'hi
+# there.' output as the second line from our shell script.
+#
+# Note that you must alter the mib.txt file to be correct if you want
+# the .50.* outputs above to change to reasonable text descriptions.
+
+# Other ideas:
+#
+# exec .1.3.6.1.4.1.2021.51 ps /bin/ps
+# exec .1.3.6.1.4.1.2021.52 top /usr/local/bin/top
+# exec .1.3.6.1.4.1.2021.53 mailq /usr/bin/mailq
+
+# -----------------------------------------------------------------------------
+
+
+###############################################################################
+# Pass through control.
+#
+
+# Usage:
+# pass MIBOID EXEC-COMMAND
+#
+# This will pass total control of the mib underneath the MIBOID
+# portion of the mib to the EXEC-COMMAND.
+#
+# Note: You'll have to change the path of the passtest script to your
+# source directory or install it in the given location.
+#
+# Example: (see the script for details)
+# (commented out here since it requires that you place the
+# script in the right location. (its not installed by default))
+
+# pass .1.3.6.1.4.1.2021.255 /bin/sh /usr/local/local/passtest
+
+# % snmpwalk -v 1 localhost -c public .1.3.6.1.4.1.2021.255
+# enterprises.ucdavis.255.1 = "life the universe and everything"
+# enterprises.ucdavis.255.2.1 = 42
+# enterprises.ucdavis.255.2.2 = OID: 42.42.42
+# enterprises.ucdavis.255.3 = Timeticks: (363136200) 42 days, 0:42:42
+# enterprises.ucdavis.255.4 = IpAddress: 127.0.0.1
+# enterprises.ucdavis.255.5 = 42
+# enterprises.ucdavis.255.6 = Gauge: 42
+#
+# % snmpget -v 1 localhost public .1.3.6.1.4.1.2021.255.5
+# enterprises.ucdavis.255.5 = 42
+#
+# % snmpset -v 1 localhost public .1.3.6.1.4.1.2021.255.1 s "New string"
+# enterprises.ucdavis.255.1 = "New string"
+#
+
+# For specific usage information, see the man/snmpd.conf.5 manual page
+# as well as the local/passtest script used in the above example.
+
+###############################################################################
+# Further Information
+#
+# See the snmpd.conf manual page, and the output of "snmpd -H".
projects / people / ms / ipfire-3.x.git / blobdiff