#include <malloc.h>
#include <asm/io.h>
#include <asm/arch/hardware.h>
+#include <dm.h>
/* SPIGCR0 */
#define SPIGCR0_SPIENA_MASK 0x1
/* SPIDEF */
#define SPIDEF_CSDEF0_MASK BIT(0)
+#ifndef CONFIG_DM_SPI
#define SPI0_BUS 0
#define SPI0_BASE CONFIG_SYS_SPI_BASE
/*
#define SPI2_NUM_CS CONFIG_SYS_SPI2_NUM_CS
#define SPI2_BASE CONFIG_SYS_SPI2_BASE
#endif
+#endif
+
+DECLARE_GLOBAL_DATA_PTR;
/* davinci spi register set */
struct davinci_spi_regs {
/* davinci spi slave */
struct davinci_spi_slave {
+#ifndef CONFIG_DM_SPI
struct spi_slave slave;
+#endif
struct davinci_spi_regs *regs;
- unsigned int freq;
+ unsigned int freq; /* current SPI bus frequency */
+ unsigned int mode; /* current SPI mode used */
+ u8 num_cs; /* total no. of CS available */
+ u8 cur_cs; /* CS of current slave */
+ bool half_duplex; /* true, if master is half-duplex only */
};
-static inline struct davinci_spi_slave *to_davinci_spi(struct spi_slave *slave)
-{
- return container_of(slave, struct davinci_spi_slave, slave);
-}
-
/*
* This functions needs to act like a macro to avoid pipeline reloads in the
* loops below. Use always_inline. This gains us about 160KiB/s and the bloat
return buf_reg_val;
}
-static int davinci_spi_read(struct spi_slave *slave, unsigned int len,
+static int davinci_spi_read(struct davinci_spi_slave *ds, unsigned int len,
u8 *rxp, unsigned long flags)
{
- struct davinci_spi_slave *ds = to_davinci_spi(slave);
unsigned int data1_reg_val;
/* enable CS hold, CS[n] and clear the data bits */
data1_reg_val = ((1 << SPIDAT1_CSHOLD_SHIFT) |
- (slave->cs << SPIDAT1_CSNR_SHIFT));
+ (ds->cur_cs << SPIDAT1_CSNR_SHIFT));
/* wait till TXFULL is deasserted */
while (readl(&ds->regs->buf) & SPIBUF_TXFULL_MASK)
return 0;
}
-static int davinci_spi_write(struct spi_slave *slave, unsigned int len,
+static int davinci_spi_write(struct davinci_spi_slave *ds, unsigned int len,
const u8 *txp, unsigned long flags)
{
- struct davinci_spi_slave *ds = to_davinci_spi(slave);
unsigned int data1_reg_val;
/* enable CS hold and clear the data bits */
data1_reg_val = ((1 << SPIDAT1_CSHOLD_SHIFT) |
- (slave->cs << SPIDAT1_CSNR_SHIFT));
+ (ds->cur_cs << SPIDAT1_CSNR_SHIFT));
/* wait till TXFULL is deasserted */
while (readl(&ds->regs->buf) & SPIBUF_TXFULL_MASK)
return 0;
}
-#ifndef CONFIG_SPI_HALF_DUPLEX
-static int davinci_spi_read_write(struct spi_slave *slave, unsigned int len,
- u8 *rxp, const u8 *txp, unsigned long flags)
+static int davinci_spi_read_write(struct davinci_spi_slave *ds, unsigned
+ int len, u8 *rxp, const u8 *txp,
+ unsigned long flags)
{
- struct davinci_spi_slave *ds = to_davinci_spi(slave);
unsigned int data1_reg_val;
/* enable CS hold and clear the data bits */
data1_reg_val = ((1 << SPIDAT1_CSHOLD_SHIFT) |
- (slave->cs << SPIDAT1_CSNR_SHIFT));
+ (ds->cur_cs << SPIDAT1_CSNR_SHIFT));
/* wait till TXFULL is deasserted */
while (readl(&ds->regs->buf) & SPIBUF_TXFULL_MASK)
return 0;
}
-#endif
+
+
+static int __davinci_spi_claim_bus(struct davinci_spi_slave *ds, int cs)
+{
+ unsigned int mode = 0, scalar;
+
+ /* Enable the SPI hardware */
+ writel(SPIGCR0_SPIRST_MASK, &ds->regs->gcr0);
+ udelay(1000);
+ writel(SPIGCR0_SPIENA_MASK, &ds->regs->gcr0);
+
+ /* Set master mode, powered up and not activated */
+ writel(SPIGCR1_MASTER_MASK | SPIGCR1_CLKMOD_MASK, &ds->regs->gcr1);
+
+ /* CS, CLK, SIMO and SOMI are functional pins */
+ writel(((1 << cs) | SPIPC0_CLKFUN_MASK |
+ SPIPC0_DOFUN_MASK | SPIPC0_DIFUN_MASK), &ds->regs->pc0);
+
+ /* setup format */
+ scalar = ((CONFIG_SYS_SPI_CLK / ds->freq) - 1) & 0xFF;
+
+ /*
+ * Use following format:
+ * character length = 8,
+ * MSB shifted out first
+ */
+ if (ds->mode & SPI_CPOL)
+ mode |= SPI_CPOL;
+ if (!(ds->mode & SPI_CPHA))
+ mode |= SPI_CPHA;
+ writel(8 | (scalar << SPIFMT_PRESCALE_SHIFT) |
+ (mode << SPIFMT_PHASE_SHIFT), &ds->regs->fmt0);
+
+ /*
+ * Including a minor delay. No science here. Should be good even with
+ * no delay
+ */
+ writel((50 << SPI_C2TDELAY_SHIFT) |
+ (50 << SPI_T2CDELAY_SHIFT), &ds->regs->delay);
+
+ /* default chip select register */
+ writel(SPIDEF_CSDEF0_MASK, &ds->regs->def);
+
+ /* no interrupts */
+ writel(0, &ds->regs->int0);
+ writel(0, &ds->regs->lvl);
+
+ /* enable SPI */
+ writel((readl(&ds->regs->gcr1) | SPIGCR1_SPIENA_MASK), &ds->regs->gcr1);
+
+ return 0;
+}
+
+static int __davinci_spi_release_bus(struct davinci_spi_slave *ds)
+{
+ /* Disable the SPI hardware */
+ writel(SPIGCR0_SPIRST_MASK, &ds->regs->gcr0);
+
+ return 0;
+}
+
+static int __davinci_spi_xfer(struct davinci_spi_slave *ds,
+ unsigned int bitlen, const void *dout, void *din,
+ unsigned long flags)
+{
+ unsigned int len;
+
+ if (bitlen == 0)
+ /* Finish any previously submitted transfers */
+ goto out;
+
+ /*
+ * It's not clear how non-8-bit-aligned transfers are supposed to be
+ * represented as a stream of bytes...this is a limitation of
+ * the current SPI interface - here we terminate on receiving such a
+ * transfer request.
+ */
+ if (bitlen % 8) {
+ /* Errors always terminate an ongoing transfer */
+ flags |= SPI_XFER_END;
+ goto out;
+ }
+
+ len = bitlen / 8;
+
+ if (!dout)
+ return davinci_spi_read(ds, len, din, flags);
+ if (!din)
+ return davinci_spi_write(ds, len, dout, flags);
+ if (!ds->half_duplex)
+ return davinci_spi_read_write(ds, len, din, dout, flags);
+
+ printf("SPI full duplex not supported\n");
+ flags |= SPI_XFER_END;
+
+out:
+ if (flags & SPI_XFER_END) {
+ u8 dummy = 0;
+ davinci_spi_write(ds, 1, &dummy, flags);
+ }
+ return 0;
+}
+
+#ifndef CONFIG_DM_SPI
+
+static inline struct davinci_spi_slave *to_davinci_spi(struct spi_slave *slave)
+{
+ return container_of(slave, struct davinci_spi_slave, slave);
+}
int spi_cs_is_valid(unsigned int bus, unsigned int cs)
{
}
ds->freq = max_hz;
+ ds->mode = mode;
return &ds->slave;
}
free(ds);
}
+int spi_xfer(struct spi_slave *slave, unsigned int bitlen,
+ const void *dout, void *din, unsigned long flags)
+{
+ struct davinci_spi_slave *ds = to_davinci_spi(slave);
+
+ ds->cur_cs = slave->cs;
+
+ return __davinci_spi_xfer(ds, bitlen, dout, din, flags);
+}
+
int spi_claim_bus(struct spi_slave *slave)
{
struct davinci_spi_slave *ds = to_davinci_spi(slave);
- unsigned int scalar;
- /* Enable the SPI hardware */
- writel(SPIGCR0_SPIRST_MASK, &ds->regs->gcr0);
- udelay(1000);
- writel(SPIGCR0_SPIENA_MASK, &ds->regs->gcr0);
+#ifdef CONFIG_SPI_HALF_DUPLEX
+ ds->half_duplex = true;
+#else
+ ds->half_duplex = false;
+#endif
+ return __davinci_spi_claim_bus(ds, ds->slave.cs);
+}
- /* Set master mode, powered up and not activated */
- writel(SPIGCR1_MASTER_MASK | SPIGCR1_CLKMOD_MASK, &ds->regs->gcr1);
+void spi_release_bus(struct spi_slave *slave)
+{
+ struct davinci_spi_slave *ds = to_davinci_spi(slave);
- /* CS, CLK, SIMO and SOMI are functional pins */
- writel(((1 << slave->cs) | SPIPC0_CLKFUN_MASK |
- SPIPC0_DOFUN_MASK | SPIPC0_DIFUN_MASK), &ds->regs->pc0);
+ __davinci_spi_release_bus(ds);
+}
- /* setup format */
- scalar = ((CONFIG_SYS_SPI_CLK / ds->freq) - 1) & 0xFF;
+#else
+static int davinci_spi_set_speed(struct udevice *bus, uint max_hz)
+{
+ struct davinci_spi_slave *ds = dev_get_priv(bus);
- /*
- * Use following format:
- * character length = 8,
- * clock signal delayed by half clk cycle,
- * clock low in idle state - Mode 0,
- * MSB shifted out first
- */
- writel(8 | (scalar << SPIFMT_PRESCALE_SHIFT) |
- (1 << SPIFMT_PHASE_SHIFT), &ds->regs->fmt0);
+ debug("%s speed %u\n", __func__, max_hz);
+ if (max_hz > CONFIG_SYS_SPI_CLK / 2)
+ return -EINVAL;
- /*
- * Including a minor delay. No science here. Should be good even with
- * no delay
- */
- writel((50 << SPI_C2TDELAY_SHIFT) |
- (50 << SPI_T2CDELAY_SHIFT), &ds->regs->delay);
+ ds->freq = max_hz;
- /* default chip select register */
- writel(SPIDEF_CSDEF0_MASK, &ds->regs->def);
+ return 0;
+}
- /* no interrupts */
- writel(0, &ds->regs->int0);
- writel(0, &ds->regs->lvl);
+static int davinci_spi_set_mode(struct udevice *bus, uint mode)
+{
+ struct davinci_spi_slave *ds = dev_get_priv(bus);
- /* enable SPI */
- writel((readl(&ds->regs->gcr1) | SPIGCR1_SPIENA_MASK), &ds->regs->gcr1);
+ debug("%s mode %u\n", __func__, mode);
+ ds->mode = mode;
return 0;
}
-void spi_release_bus(struct spi_slave *slave)
+static int davinci_spi_claim_bus(struct udevice *dev)
{
- struct davinci_spi_slave *ds = to_davinci_spi(slave);
+ struct dm_spi_slave_platdata *slave_plat =
+ dev_get_parent_platdata(dev);
+ struct udevice *bus = dev->parent;
+ struct davinci_spi_slave *ds = dev_get_priv(bus);
+
+ if (slave_plat->cs >= ds->num_cs) {
+ printf("Invalid SPI chipselect\n");
+ return -EINVAL;
+ }
+ ds->half_duplex = slave_plat->mode & SPI_PREAMBLE;
- /* Disable the SPI hardware */
- writel(SPIGCR0_SPIRST_MASK, &ds->regs->gcr0);
+ return __davinci_spi_claim_bus(ds, slave_plat->cs);
}
-int spi_xfer(struct spi_slave *slave, unsigned int bitlen,
- const void *dout, void *din, unsigned long flags)
+static int davinci_spi_release_bus(struct udevice *dev)
{
- unsigned int len;
+ struct davinci_spi_slave *ds = dev_get_priv(dev->parent);
- if (bitlen == 0)
- /* Finish any previously submitted transfers */
- goto out;
+ return __davinci_spi_release_bus(ds);
+}
- /*
- * It's not clear how non-8-bit-aligned transfers are supposed to be
- * represented as a stream of bytes...this is a limitation of
- * the current SPI interface - here we terminate on receiving such a
- * transfer request.
- */
- if (bitlen % 8) {
- /* Errors always terminate an ongoing transfer */
- flags |= SPI_XFER_END;
- goto out;
+static int davinci_spi_xfer(struct udevice *dev, unsigned int bitlen,
+ const void *dout, void *din,
+ unsigned long flags)
+{
+ struct dm_spi_slave_platdata *slave =
+ dev_get_parent_platdata(dev);
+ struct udevice *bus = dev->parent;
+ struct davinci_spi_slave *ds = dev_get_priv(bus);
+
+ if (slave->cs >= ds->num_cs) {
+ printf("Invalid SPI chipselect\n");
+ return -EINVAL;
}
+ ds->cur_cs = slave->cs;
- len = bitlen / 8;
+ return __davinci_spi_xfer(ds, bitlen, dout, din, flags);
+}
- if (!dout)
- return davinci_spi_read(slave, len, din, flags);
- else if (!din)
- return davinci_spi_write(slave, len, dout, flags);
-#ifndef CONFIG_SPI_HALF_DUPLEX
- else
- return davinci_spi_read_write(slave, len, din, dout, flags);
-#else
- printf("SPI full duplex transaction requested with "
- "CONFIG_SPI_HALF_DUPLEX defined.\n");
- flags |= SPI_XFER_END;
-#endif
+static int davinci_spi_probe(struct udevice *bus)
+{
+ /* Nothing to do */
+ return 0;
+}
-out:
- if (flags & SPI_XFER_END) {
- u8 dummy = 0;
- davinci_spi_write(slave, 1, &dummy, flags);
+static int davinci_ofdata_to_platadata(struct udevice *bus)
+{
+ struct davinci_spi_slave *ds = dev_get_priv(bus);
+ const void *blob = gd->fdt_blob;
+ int node = bus->of_offset;
+
+ ds->regs = dev_map_physmem(bus, sizeof(struct davinci_spi_regs));
+ if (!ds->regs) {
+ printf("%s: could not map device address\n", __func__);
+ return -EINVAL;
}
+ ds->num_cs = fdtdec_get_int(blob, node, "num-cs", 4);
+
return 0;
}
+
+static const struct dm_spi_ops davinci_spi_ops = {
+ .claim_bus = davinci_spi_claim_bus,
+ .release_bus = davinci_spi_release_bus,
+ .xfer = davinci_spi_xfer,
+ .set_speed = davinci_spi_set_speed,
+ .set_mode = davinci_spi_set_mode,
+};
+
+static const struct udevice_id davinci_spi_ids[] = {
+ { .compatible = "ti,keystone-spi" },
+ { .compatible = "ti,dm6441-spi" },
+ { }
+};
+
+U_BOOT_DRIVER(davinci_spi) = {
+ .name = "davinci_spi",
+ .id = UCLASS_SPI,
+ .of_match = davinci_spi_ids,
+ .ops = &davinci_spi_ops,
+ .ofdata_to_platdata = davinci_ofdata_to_platadata,
+ .priv_auto_alloc_size = sizeof(struct davinci_spi_slave),
+ .probe = davinci_spi_probe,
+};
+#endif
projects / people / ms / u-boot.git / commitdiff
