sunxi: olinuxino ethernet wireless emmc

diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts
index 389a38704f660ea221c4861ff0a7ad408a2cb799..d8fae3469eb555de068a1eef70c01e72af98eac1 100644 (file)
--- a/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts
+++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-olinuxino.dts
@@ -1,5 +1,6 @@
 /*
  * Copyright (C) 2017 Jagan Teki <jteki@openedev.com>
+ * Armbian(c)
  *
  * This file is dual-licensed: you can use it either under the terms
  * of the GPL or the X11 license, at your option. Note that this dual
@@ -51,12 +52,65 @@
        compatible = "olimex,a64-olinuxino", "allwinner,sun50i-a64";
 
        aliases {
+               ethernet0 = &emac;
                serial0 = &uart0;
+               serial1 = &uart1;
        };
 
        chosen {
                stdout-path = "serial0:115200n8";
        };
+
+       wifi_pwrseq: wifi_pwrseq {
+               compatible = "mmc-pwrseq-simple";
+               reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
+       };
+};
+
+&de {
+       status = "okay";
+};
+
+&ehci0 {
+       status = "okay";
+};
+
+&ehci1 {
+       status = "okay";
+};
+
+&emac {
+       pinctrl-names = "default";
+       pinctrl-0 = <&rgmii_pins>;
+       phy-mode = "rgmii-txid";
+       phy-handle = <&ext_rgmii_phy>;
+       status = "okay";
+};
+
+&hdmi {
+       hvcc-supply = <&reg_dldo1>;
+       status = "okay";
+};
+
+&i2c1 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&i2c1_pins>;
+       status = "okay";
+};
+
+&i2c1_pins {
+       bias-pull-up;
+};
+
+&mdio {
+       ext_rgmii_phy: ethernet-phy@1 {
+               compatible = "ethernet-phy-ieee802.3-c22";
+               reg = <1>;
+       };
+};
+
+&mixer1 {
+       status = "okay";
 };
 
 &mmc0 {
@@ -70,6 +124,42 @@
        status = "okay";
 };
 
+&mmc1 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&mmc1_pins>;
+       vmmc-supply = <&reg_aldo2>;
+       vqmmc-supply = <&reg_dldo4>;
+       mmc-pwrseq = <&wifi_pwrseq>;
+       bus-width = <4>;
+       non-removable;
+       status = "okay";
+
+       rtl8723bs: wifi@1 {
+               reg = <1>;
+               interrupt-parent = <&r_pio>;
+               interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
+               interrupt-names = "host-wake";
+       };
+};
+
+&mmc2 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&mmc2_pins>;
+       vmmc-supply = <&reg_dcdc1>;
+       bus-width = <8>;
+       non-removable;
+       cap-mmc-hw-reset;
+       status = "okay";
+};
+
+&ohci0 {
+       status = "okay";
+};
+
+&ohci1 {
+       status = "okay";
+};
+
 &r_rsb {
        status = "okay";
 
@@ -78,6 +168,7 @@
                reg = <0x3a3>;
                interrupt-parent = <&r_intc>;
                interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+               x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */
        };
 };
 
@@ -196,8 +287,8 @@
        regulator-name = "vcc-rtc";
 };
 
-&simplefb_hdmi {
-       vcc-hdmi-supply = <&reg_dldo1>;
+&tcon1 {
+       status = "okay";
 };
 
 &uart0 {
@@ -205,3 +296,13 @@
        pinctrl-0 = <&uart0_pins_a>;
        status = "okay";
 };
+
+&uart1 {
+       pinctrl-names = "default";
+       pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
+       status = "okay";
+};
+
+&usbphy {
+       status = "okay";
+};
\ No newline at end of file