[people/ms/u-boot.git] / include / configs / ls2080a_common.h

/*
 * Copyright (C) 2014 Freescale Semiconductor
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __LS2_COMMON_H
#define __LS2_COMMON_H

#define CONFIG_REMAKE_ELF
#define CONFIG_FSL_LAYERSCAPE
#define CONFIG_FSL_LSCH3
#define CONFIG_MP
#define CONFIG_GICV3
#define CONFIG_FSL_TZPC_BP147

#include <asm/arch/ls2080a_stream_id.h>
#include <asm/arch/config.h>
#if (defined(CONFIG_SYS_FSL_SRDS_1) || defined(CONFIG_SYS_FSL_SRDS_2))
#define	CONFIG_SYS_HAS_SERDES
#endif

/* Link Definitions */
#define CONFIG_SYS_INIT_SP_ADDR		(CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)

/* We need architecture specific misc initializations */
#define CONFIG_ARCH_MISC_INIT

/* Link Definitions */
#ifdef CONFIG_SPL
#define CONFIG_SYS_TEXT_BASE		0x80400000
#else
#define CONFIG_SYS_TEXT_BASE		0x30100000
#endif

#ifdef CONFIG_EMU
#define CONFIG_SYS_NO_FLASH
#endif

#define CONFIG_SUPPORT_RAW_INITRD

#define CONFIG_SKIP_LOWLEVEL_INIT
#define CONFIG_BOARD_EARLY_INIT_F	1

#ifndef CONFIG_SPL
#define CONFIG_FSL_DDR_INTERACTIVE	/* Interactive debugging */
#endif
#ifndef CONFIG_SYS_FSL_DDR4
#define CONFIG_SYS_FSL_DDR3		/* Use DDR3 memory */
#define CONFIG_SYS_DDR_RAW_TIMING
#endif

#define CONFIG_SYS_FSL_DDR_INTLV_256B	/* force 256 byte interleaving */

#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE	0x80000000UL
#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY	0
#define CONFIG_SYS_SDRAM_BASE		CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_SYS_DDR_BLOCK2_BASE	0x8080000000ULL
#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS	2

/*
 * SMP Definitinos
 */
#define CPU_RELEASE_ADDR		secondary_boot_func

#define CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
#define CONFIG_SYS_DP_DDR_BASE		0x6000000000ULL
/*
 * DDR controller use 0 as the base address for binding.
 * It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
 */
#define CONFIG_SYS_DP_DDR_BASE_PHY	0
#define CONFIG_DP_DDR_CTRL		2
#define CONFIG_DP_DDR_NUM_CTRLS		1
#endif

/* Generic Timer Definitions */
/*
 * This is not an accurate number. It is used in start.S. The frequency
 * will be udpated later when get_bus_freq(0) is available.
 */
#define COUNTER_FREQUENCY		25000000	/* 25MHz */

/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN		(CONFIG_ENV_SIZE + 2048 * 1024)

/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */
#define CONFIG_SYS_I2C_MXC_I2C4		/* enable I2C bus 4 */

/* Serial Port */
#define CONFIG_CONS_INDEX       1
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE     1
#define CONFIG_SYS_NS16550_CLK          (get_bus_freq(0)/2)

#define CONFIG_BAUDRATE			115200
#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }

/* IFC */
#define CONFIG_FSL_IFC

/*
 * During booting, IFC is mapped at the region of 0x30000000.
 * But this region is limited to 256MB. To accommodate NOR, promjet
 * and FPGA. This region is divided as below:
 * 0x30000000 - 0x37ffffff : 128MB : NOR flash
 * 0x38000000 - 0x3BFFFFFF : 64MB  : Promjet
 * 0x3C000000 - 0x40000000 : 64MB  : FPGA etc
 *
 * To accommodate bigger NOR flash and other devices, we will map IFC
 * chip selects to as below:
 * 0x5_1000_0000..0x5_1fff_ffff	Memory Hole
 * 0x5_2000_0000..0x5_3fff_ffff	IFC CSx (FPGA, NAND and others 512MB)
 * 0x5_4000_0000..0x5_7fff_ffff	ASIC or others 1GB
 * 0x5_8000_0000..0x5_bfff_ffff	IFC CS0 1GB (NOR/Promjet)
 * 0x5_C000_0000..0x5_ffff_ffff	IFC CS1 1GB (NOR/Promjet)
 *
 * For e.g. NOR flash at CS0 will be mapped to 0x580000000 after relocation.
 * CONFIG_SYS_FLASH_BASE has the final address (core view)
 * CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
 * CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
 * CONFIG_SYS_TEXT_BASE is linked to 0x30000000 for booting
 */

#define CONFIG_SYS_FLASH_BASE			0x580000000ULL
#define CONFIG_SYS_FLASH_BASE_PHYS		0x80000000
#define CONFIG_SYS_FLASH_BASE_PHYS_EARLY	0x00000000

#define CONFIG_SYS_FLASH1_BASE_PHYS		0xC0000000
#define CONFIG_SYS_FLASH1_BASE_PHYS_EARLY	0x8000000

#ifndef CONFIG_SYS_NO_FLASH
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
#define CONFIG_SYS_FLASH_QUIET_TEST
#endif

#ifndef __ASSEMBLY__
unsigned long long get_qixis_addr(void);
#endif
#define QIXIS_BASE				get_qixis_addr()
#define QIXIS_BASE_PHYS				0x20000000
#define QIXIS_BASE_PHYS_EARLY			0xC000000
#define QIXIS_STAT_PRES1			0xb
#define QIXIS_SDID_MASK				0x07
#define QIXIS_ESDHC_NO_ADAPTER			0x7

#define CONFIG_SYS_NAND_BASE			0x530000000ULL
#define CONFIG_SYS_NAND_BASE_PHYS		0x30000000

/* Debug Server firmware */
#define CONFIG_FSL_DEBUG_SERVER
/* 2 sec timeout */
#define CONFIG_SYS_DEBUG_SERVER_TIMEOUT			(2 * 1000 * 1000)

/* MC firmware */
#define CONFIG_FSL_MC_ENET
/* TODO Actual DPL max length needs to be confirmed with the MC FW team */
#define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH	    0x20000
#define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET    0x00F00000
#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH	    0x20000
#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET    0x00F20000
/* For LS2085A */
#define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH	0x200000
#define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET	0x07000000

/*
 * Carve out a DDR region which will not be used by u-boot/Linux
 *
 * It will be used by MC and Debug Server. The MC region must be
 * 512MB aligned, so the min size to hide is 512MB.
 */
#if defined(CONFIG_FSL_MC_ENET) || defined(CONFIG_FSL_DEBUG_SERVER)
#define CONFIG_SYS_DEBUG_SERVER_DRAM_BLOCK_MIN_SIZE	(254UL * 1024 * 1024)
#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE		(512UL * 1024 * 1024)
#define CONFIG_SYS_MC_RSV_MEM_ALIGN			(512UL * 1024 * 1024)
#endif

/* PCIe */
#define CONFIG_PCIE1		/* PCIE controler 1 */
#define CONFIG_PCIE2		/* PCIE controler 2 */
#define CONFIG_PCIE3		/* PCIE controler 3 */
#define CONFIG_PCIE4		/* PCIE controler 4 */
#define CONFIG_PCIE_LAYERSCAPE	/* Use common FSL Layerscape PCIe code */
#ifdef CONFIG_LS2080A
#define FSL_PCIE_COMPAT "fsl,ls2080a-pcie"
#endif

#define CONFIG_SYS_PCI_64BIT

#define CONFIG_SYS_PCIE_CFG0_PHYS_OFF	0x00000000
#define CONFIG_SYS_PCIE_CFG0_SIZE	0x00001000	/* 4k */
#define CONFIG_SYS_PCIE_CFG1_PHYS_OFF	0x00001000
#define CONFIG_SYS_PCIE_CFG1_SIZE	0x00001000	/* 4k */

#define CONFIG_SYS_PCIE_IO_BUS		0x00000000
#define CONFIG_SYS_PCIE_IO_PHYS_OFF	0x00010000
#define CONFIG_SYS_PCIE_IO_SIZE		0x00010000	/* 64k */

#define CONFIG_SYS_PCIE_MEM_BUS		0x40000000
#define CONFIG_SYS_PCIE_MEM_PHYS_OFF	0x40000000
#define CONFIG_SYS_PCIE_MEM_SIZE	0x40000000	/* 1G */

/* Command line configuration */
#define CONFIG_CMD_ENV

/* Miscellaneous configurable options */
#define CONFIG_SYS_LOAD_ADDR	(CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
#define CONFIG_ARCH_EARLY_INIT_R

/* Physical Memory Map */
/* fixme: these need to be checked against the board */
#define CONFIG_CHIP_SELECTS_PER_CTRL	4

#define CONFIG_NR_DRAM_BANKS		3

#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE		128

#define CONFIG_DISPLAY_CPUINFO

/* Allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE

/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS		\
	"hwconfig=fsl_ddr:bank_intlv=auto\0"	\
	"loadaddr=0x80100000\0"			\
	"kernel_addr=0x100000\0"		\
	"ramdisk_addr=0x800000\0"		\
	"ramdisk_size=0x2000000\0"		\
	"fdt_high=0xa0000000\0"			\
	"initrd_high=0xffffffffffffffff\0"	\
	"kernel_start=0x581200000\0"		\
	"kernel_load=0xa0000000\0"		\
	"kernel_size=0x2800000\0"		\
	"console=ttyAMA0,38400n8\0"		\
	"mcinitcmd=fsl_mc start mc 0x580300000"	\
	" 0x580800000 \0"

#define CONFIG_BOOTARGS		"console=ttyS0,115200 root=/dev/ram0 " \
				"earlycon=uart8250,mmio,0x21c0500 " \
				"ramdisk_size=0x2000000 default_hugepagesz=2m" \
				" hugepagesz=2m hugepages=256"
#define CONFIG_BOOTCOMMAND	"fsl_mc apply dpl 0x580700000 &&" \
				" cp.b $kernel_start $kernel_load" \
				" $kernel_size && bootm $kernel_load"
#define CONFIG_BOOTDELAY		10

/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE		512	/* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
					sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE /* Boot args buffer */
#define CONFIG_SYS_LONGHELP
#define CONFIG_CMDLINE_EDITING		1
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_MAXARGS		64	/* max command args */

#define CONFIG_PANIC_HANG	/* do not reset board on panic */

#define CONFIG_SPL_BSS_START_ADDR	0x80100000
#define CONFIG_SPL_BSS_MAX_SIZE		0x00100000
#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
#define CONFIG_SPL_ENV_SUPPORT
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_I2C_SUPPORT
#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_MAX_SIZE		0x16000
#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT
#define CONFIG_SPL_STACK		(CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0)
#define CONFIG_SPL_TARGET		"u-boot-with-spl.bin"
#define CONFIG_SPL_TEXT_BASE		0x1800a000

#define CONFIG_SYS_NAND_U_BOOT_DST	0x80400000
#define CONFIG_SYS_NAND_U_BOOT_START	CONFIG_SYS_NAND_U_BOOT_DST
#define CONFIG_SYS_SPL_MALLOC_SIZE	0x00100000
#define CONFIG_SYS_SPL_MALLOC_START	0x80200000
#define CONFIG_SYS_MONITOR_LEN		(512 * 1024)

#define CONFIG_SYS_BOOTM_LEN   (64 << 20)      /* Increase max gunzip size */

#endif /* __LS2_COMMON_H */
Commit	Line	Data
f749db3a YS	1	/*
	2	* Copyright (C) 2014 Freescale Semiconductor
	3	*
	4	* SPDX-License-Identifier: GPL-2.0+
	5	*/
	6
	7	#ifndef __LS2_COMMON_H
	8	#define __LS2_COMMON_H
	9
f749db3a	10	#define CONFIG_REMAKE_ELF
9f3183d2	11	#define CONFIG_FSL_LAYERSCAPE
f749db3a	12	#define CONFIG_FSL_LSCH3
9f3183d2	13	#define CONFIG_MP
f749db3a	14	#define CONFIG_GICV3
9c66ce66	15	#define CONFIG_FSL_TZPC_BP147
f749db3a	16
44937214	17	#include <asm/arch/ls2080a_stream_id.h>
9f3183d2	18	#include <asm/arch/config.h>
31d34c6c ML	19	#if (defined(CONFIG_SYS_FSL_SRDS_1) \|\| defined(CONFIG_SYS_FSL_SRDS_2))
	20	#define CONFIG_SYS_HAS_SERDES
	21	#endif
	22
9f3183d2 MH	23	/* Link Definitions */
	24	#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
	25
422cb08a BS	26	/* We need architecture specific misc initializations */
	27	#define CONFIG_ARCH_MISC_INIT
	28
f749db3a	29	/* Link Definitions */
b2d5ac59 SW	30	#ifdef CONFIG_SPL
	31	#define CONFIG_SYS_TEXT_BASE 0x80400000
	32	#else
f3f8c564	33	#define CONFIG_SYS_TEXT_BASE 0x30100000
b2d5ac59	34	#endif
f749db3a	35
e211c12e	36	#ifdef CONFIG_EMU
f749db3a	37	#define CONFIG_SYS_NO_FLASH
e211c12e	38	#endif
f749db3a YS	39
	40	#define CONFIG_SUPPORT_RAW_INITRD
	41
	42	#define CONFIG_SKIP_LOWLEVEL_INIT
	43	#define CONFIG_BOARD_EARLY_INIT_F 1
	44
b2d5ac59	45	#ifndef CONFIG_SPL
f749db3a	46	#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
b2d5ac59	47	#endif
f749db3a YS	48	#ifndef CONFIG_SYS_FSL_DDR4
	49	#define CONFIG_SYS_FSL_DDR3 /* Use DDR3 memory */
	50	#define CONFIG_SYS_DDR_RAW_TIMING
	51	#endif
f749db3a YS	52
	53	#define CONFIG_SYS_FSL_DDR_INTLV_256B /* force 256 byte interleaving */
	54
9f3183d2	55	#define CONFIG_VERY_BIG_RAM
f749db3a YS	56	#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
	57	#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
	58	#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
	59	#define CONFIG_SYS_DDR_BLOCK2_BASE 0x8080000000ULL
d9c68b14 YS	60	#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS 2
d9c68b14 YS	61
8bfa301b YS	62	/*
	63	* SMP Definitinos
	64	*/
	65	#define CPU_RELEASE_ADDR secondary_boot_func
	66
d9c68b14	67	#define CONFIG_SYS_FSL_OTHER_DDR_NUM_CTRLS
44937214	68	#ifdef CONFIG_SYS_FSL_HAS_DP_DDR
d9c68b14 YS	69	#define CONFIG_SYS_DP_DDR_BASE 0x6000000000ULL
	70	/*
	71	* DDR controller use 0 as the base address for binding.
	72	* It is mapped to CONFIG_SYS_DP_DDR_BASE for core to access.
	73	*/
	74	#define CONFIG_SYS_DP_DDR_BASE_PHY 0
	75	#define CONFIG_DP_DDR_CTRL 2
	76	#define CONFIG_DP_DDR_NUM_CTRLS 1
44937214	77	#endif
f749db3a YS	78
f749db3a YS	79	/* Generic Timer Definitions */
207774b2 YS	80	/*
	81	* This is not an accurate number. It is used in start.S. The frequency
	82	* will be udpated later when get_bus_freq(0) is available.
	83	*/
	84	#define COUNTER_FREQUENCY 25000000 /* 25MHz */
f749db3a YS	85
f749db3a YS	86	/* Size of malloc() pool */
aa66acbf	87	#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2048 * 1024)
f749db3a YS	88
f749db3a YS	89	/* I2C */
f749db3a YS	90	#define CONFIG_SYS_I2C
f749db3a YS	91	#define CONFIG_SYS_I2C_MXC
03544c66 AA	92	#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
03544c66 AA	93	#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
f8cb101e YS	94	#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
f8cb101e YS	95	#define CONFIG_SYS_I2C_MXC_I2C4 /* enable I2C bus 4 */
f749db3a YS	96
f749db3a YS	97	/* Serial Port */
7288c2c2	98	#define CONFIG_CONS_INDEX 1
f749db3a YS	99	#define CONFIG_SYS_NS16550_SERIAL
	100	#define CONFIG_SYS_NS16550_REG_SIZE 1
	101	#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2)
	102
	103	#define CONFIG_BAUDRATE 115200
	104	#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
	105
	106	/* IFC */
	107	#define CONFIG_FSL_IFC
f3f8c564	108
f749db3a	109	/*
7288c2c2 YS	110	* During booting, IFC is mapped at the region of 0x30000000.
	111	* But this region is limited to 256MB. To accommodate NOR, promjet
	112	* and FPGA. This region is divided as below:
	113	* 0x30000000 - 0x37ffffff : 128MB : NOR flash
	114	* 0x38000000 - 0x3BFFFFFF : 64MB : Promjet
	115	* 0x3C000000 - 0x40000000 : 64MB : FPGA etc
	116	*
	117	* To accommodate bigger NOR flash and other devices, we will map IFC
	118	* chip selects to as below:
	119	* 0x5_1000_0000..0x5_1fff_ffff Memory Hole
	120	* 0x5_2000_0000..0x5_3fff_ffff IFC CSx (FPGA, NAND and others 512MB)
	121	* 0x5_4000_0000..0x5_7fff_ffff ASIC or others 1GB
	122	* 0x5_8000_0000..0x5_bfff_ffff IFC CS0 1GB (NOR/Promjet)
	123	* 0x5_C000_0000..0x5_ffff_ffff IFC CS1 1GB (NOR/Promjet)
	124	*
	125	* For e.g. NOR flash at CS0 will be mapped to 0x580000000 after relocation.
f749db3a YS	126	* CONFIG_SYS_FLASH_BASE has the final address (core view)
	127	* CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
	128	* CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
	129	* CONFIG_SYS_TEXT_BASE is linked to 0x30000000 for booting
	130	*/
7288c2c2	131
f749db3a YS	132	#define CONFIG_SYS_FLASH_BASE 0x580000000ULL
	133	#define CONFIG_SYS_FLASH_BASE_PHYS 0x80000000
	134	#define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000
	135
7288c2c2 YS	136	#define CONFIG_SYS_FLASH1_BASE_PHYS 0xC0000000
	137	#define CONFIG_SYS_FLASH1_BASE_PHYS_EARLY 0x8000000
	138
e211c12e PK	139	#ifndef CONFIG_SYS_NO_FLASH
	140	#define CONFIG_FLASH_CFI_DRIVER
	141	#define CONFIG_SYS_FLASH_CFI
	142	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
	143	#define CONFIG_SYS_FLASH_QUIET_TEST
e211c12e PK	144	#endif
e211c12e PK	145
7288c2c2 YS	146	#ifndef __ASSEMBLY__
	147	unsigned long long get_qixis_addr(void);
	148	#endif
	149	#define QIXIS_BASE get_qixis_addr()
	150	#define QIXIS_BASE_PHYS 0x20000000
	151	#define QIXIS_BASE_PHYS_EARLY 0xC000000
8b06460e YL	152	#define QIXIS_STAT_PRES1 0xb
	153	#define QIXIS_SDID_MASK 0x07
	154	#define QIXIS_ESDHC_NO_ADAPTER 0x7
7288c2c2 YS	155
	156	#define CONFIG_SYS_NAND_BASE 0x530000000ULL
	157	#define CONFIG_SYS_NAND_BASE_PHYS 0x30000000
e211c12e	158
422cb08a	159	/* Debug Server firmware */
b0ba9d48	160	#define CONFIG_FSL_DEBUG_SERVER
422cb08a BS	161	/* 2 sec timeout */
	162	#define CONFIG_SYS_DEBUG_SERVER_TIMEOUT (2 * 1000 * 1000)
	163
f749db3a YS	164	/* MC firmware */
f749db3a YS	165	#define CONFIG_FSL_MC_ENET
f749db3a	166	/* TODO Actual DPL max length needs to be confirmed with the MC FW team */
125e2bc1 GR	167	#define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH 0x20000
	168	#define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000
	169	#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000
	170	#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000
3c1d218a	171	/* For LS2085A */
c1000c12 GR	172	#define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH 0x200000
c1000c12 GR	173	#define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET 0x07000000
f749db3a	174
5c055089 PK	175	/*
	176	* Carve out a DDR region which will not be used by u-boot/Linux
	177	*
	178	* It will be used by MC and Debug Server. The MC region must be
	179	* 512MB aligned, so the min size to hide is 512MB.
	180	*/
422cb08a	181	#if defined(CONFIG_FSL_MC_ENET) \|\| defined(CONFIG_FSL_DEBUG_SERVER)
c0492141	182	#define CONFIG_SYS_DEBUG_SERVER_DRAM_BLOCK_MIN_SIZE (254UL * 1024 * 1024)
52c11d4f	183	#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (512UL * 1024 * 1024)
c0492141	184	#define CONFIG_SYS_MC_RSV_MEM_ALIGN (512UL * 1024 * 1024)
f749db3a YS	185	#endif
f749db3a YS	186
f3f8c564 PK	187	/* PCIe */
	188	#define CONFIG_PCIE1 /* PCIE controler 1 */
	189	#define CONFIG_PCIE2 /* PCIE controler 2 */
	190	#define CONFIG_PCIE3 /* PCIE controler 3 */
	191	#define CONFIG_PCIE4 /* PCIE controler 4 */
252b17e0	192	#define CONFIG_PCIE_LAYERSCAPE /* Use common FSL Layerscape PCIe code */
06b53010	193	#ifdef CONFIG_LS2080A
44937214	194	#define FSL_PCIE_COMPAT "fsl,ls2080a-pcie"
06b53010 PK	195	#endif
06b53010 PK	196
f3f8c564 PK	197	#define CONFIG_SYS_PCI_64BIT
	198
	199	#define CONFIG_SYS_PCIE_CFG0_PHYS_OFF 0x00000000
	200	#define CONFIG_SYS_PCIE_CFG0_SIZE 0x00001000 /* 4k */
	201	#define CONFIG_SYS_PCIE_CFG1_PHYS_OFF 0x00001000
	202	#define CONFIG_SYS_PCIE_CFG1_SIZE 0x00001000 /* 4k */
	203
	204	#define CONFIG_SYS_PCIE_IO_BUS 0x00000000
	205	#define CONFIG_SYS_PCIE_IO_PHYS_OFF 0x00010000
	206	#define CONFIG_SYS_PCIE_IO_SIZE 0x00010000 /* 64k */
	207
	208	#define CONFIG_SYS_PCIE_MEM_BUS 0x40000000
	209	#define CONFIG_SYS_PCIE_MEM_PHYS_OFF 0x40000000
	210	#define CONFIG_SYS_PCIE_MEM_SIZE 0x40000000 /* 1G */
	211
f749db3a	212	/* Command line configuration */
f749db3a	213	#define CONFIG_CMD_ENV
f749db3a YS	214
	215	/* Miscellaneous configurable options */
	216	#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
8bfa301b	217	#define CONFIG_ARCH_EARLY_INIT_R
f749db3a YS	218
	219	/* Physical Memory Map */
	220	/* fixme: these need to be checked against the board */
	221	#define CONFIG_CHIP_SELECTS_PER_CTRL 4
f749db3a	222
d9c68b14	223	#define CONFIG_NR_DRAM_BANKS 3
f749db3a	224
f749db3a YS	225	#define CONFIG_HWCONFIG
	226	#define HWCONFIG_BUFFER_SIZE 128
	227
	228	#define CONFIG_DISPLAY_CPUINFO
	229
1d3a76fa AW	230	/* Allow to overwrite serial and ethaddr */
	231	#define CONFIG_ENV_OVERWRITE
	232
f749db3a YS	233	/* Initial environment variables */
	234	#define CONFIG_EXTRA_ENV_SETTINGS \
	235	"hwconfig=fsl_ddr:bank_intlv=auto\0" \
	236	"loadaddr=0x80100000\0" \
	237	"kernel_addr=0x100000\0" \
	238	"ramdisk_addr=0x800000\0" \
	239	"ramdisk_size=0x2000000\0" \
f3f8c564	240	"fdt_high=0xa0000000\0" \
f749db3a YS	241	"initrd_high=0xffffffffffffffff\0" \
f749db3a YS	242	"kernel_start=0x581200000\0" \
052ddd5c	243	"kernel_load=0xa0000000\0" \
97421bd2	244	"kernel_size=0x2800000\0" \
16ed8560 PK	245	"console=ttyAMA0,38400n8\0" \
	246	"mcinitcmd=fsl_mc start mc 0x580300000" \
	247	" 0x580800000 \0"
f749db3a	248
56cd0760	249	#define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/ram0 " \
ed77b704	250	"earlycon=uart8250,mmio,0x21c0500 " \
34cc7546	251	"ramdisk_size=0x2000000 default_hugepagesz=2m" \
9e71bb9c	252	" hugepagesz=2m hugepages=256"
9f3e1b8a PK	253	#define CONFIG_BOOTCOMMAND "fsl_mc apply dpl 0x580700000 &&" \
	254	" cp.b $kernel_start $kernel_load" \
	255	" $kernel_size && bootm $kernel_load"
7288c2c2	256	#define CONFIG_BOOTDELAY 10
f749db3a	257
f749db3a YS	258	/* Monitor Command Prompt */
f749db3a YS	259	#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
f749db3a YS	260	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
f749db3a YS	261	sizeof(CONFIG_SYS_PROMPT) + 16)
f749db3a YS	262	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */
	263	#define CONFIG_SYS_LONGHELP
	264	#define CONFIG_CMDLINE_EDITING 1
f3f8c564	265	#define CONFIG_AUTO_COMPLETE
f749db3a YS	266	#define CONFIG_SYS_MAXARGS 64 /* max command args */
f749db3a YS	267
f3f8c564 PK	268	#define CONFIG_PANIC_HANG /* do not reset board on panic */
f3f8c564 PK	269
b2d5ac59 SW	270	#define CONFIG_SPL_BSS_START_ADDR 0x80100000
	271	#define CONFIG_SPL_BSS_MAX_SIZE 0x00100000
	272	#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
	273	#define CONFIG_SPL_ENV_SUPPORT
	274	#define CONFIG_SPL_FRAMEWORK
	275	#define CONFIG_SPL_I2C_SUPPORT
	276	#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
	277	#define CONFIG_SPL_LIBCOMMON_SUPPORT
	278	#define CONFIG_SPL_LIBGENERIC_SUPPORT
	279	#define CONFIG_SPL_MAX_SIZE 0x16000
	280	#define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT
	281	#define CONFIG_SPL_NAND_SUPPORT
	282	#define CONFIG_SPL_SERIAL_SUPPORT
	283	#define CONFIG_SPL_STACK (CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0)
	284	#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
	285	#define CONFIG_SPL_TEXT_BASE 0x1800a000
	286
	287	#define CONFIG_SYS_NAND_U_BOOT_DST 0x80400000
	288	#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
	289	#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00100000
	290	#define CONFIG_SYS_SPL_MALLOC_START 0x80200000
	291	#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
	292
34cc7546 BS	293	#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
34cc7546 BS	294
f749db3a	295	#endif /* __LS2_COMMON_H */