--- /dev/null
+##### hostapd configuration file ##############################################
+# Empty lines and lines starting with # are ignored
+
+# AP netdevice name (without 'ap' prefix, i.e., wlan0 uses wlan0ap for
+# management frames)
+interface=ath0
+
+# Driver interface type (hostap/wired/madwifi/prism54; default: hostap)
+driver=madwifi
+
+# hostapd event logger configuration
+#
+# Two output method: syslog and stdout (only usable if not forking to
+# background).
+#
+# Module bitfield (ORed bitfield of modules that will be logged; -1 = all
+# modules):
+# bit 0 (1) = IEEE 802.11
+# bit 1 (2) = IEEE 802.1X
+# bit 2 (4) = RADIUS
+# bit 3 (8) = WPA
+# bit 4 (16) = driver interface
+# bit 5 (32) = IAPP
+#
+# Levels (minimum value for logged events):
+# 0 = verbose debugging
+# 1 = debugging
+# 2 = informational messages
+# 3 = notification
+# 4 = warning
+#
+logger_syslog=-1
+logger_syslog_level=2
+logger_stdout=-1
+logger_stdout_level=1
+
+# Debugging: 0 = no, 1 = minimal, 2 = verbose, 3 = msg dumps, 4 = excessive
+debug=0
+
+# Dump file for state information (on SIGUSR1)
+dump_file=/tmp/hostapd.dump
+
+# Interface for separate control program. If this is specified, hostapd
+# will create this directory and a UNIX domain socket for listening to requests
+# from external programs (CLI/GUI, etc.) for status information and
+# configuration. The socket file will be named based on the interface name, so
+# multiple hostapd processes/interfaces can be run at the same time if more
+# than one interface is used.
+# /var/run/hostapd is the recommended directory for sockets and by default,
+# hostapd_cli will use it when trying to connect with hostapd.
+ctrl_interface=/var/run/hostapd
+
+# Access control for the control interface can be configured by setting the
+# directory to allow only members of a group to use sockets. This way, it is
+# possible to run hostapd as root (since it needs to change network
+# configuration and open raw sockets) and still allow GUI/CLI components to be
+# run as non-root users. However, since the control interface can be used to
+# change the network configuration, this access needs to be protected in many
+# cases. By default, hostapd is configured to use gid 0 (root). If you
+# want to allow non-root users to use the contron interface, add a new group
+# and change this value to match with that group. Add users that should have
+# control interface access to this group.
+#
+# This variable can be a group name or gid.
+#ctrl_interface_group=wheel
+ctrl_interface_group=0
+
+
+##### IEEE 802.11 related configuration #######################################
+
+# SSID to be used in IEEE 802.11 management frames
+ssid=IPFire
+
+# Station MAC address -based authentication
+# 0 = accept unless in deny list
+# 1 = deny unless in accept list
+# 2 = use external RADIUS server (accept/deny lists are searched first)
+macaddr_acl=0
+
+# Accept/deny lists are read from separate files (containing list of
+# MAC addresses, one per line). Use absolute path name to make sure that the
+
+# files can be read on SIGHUP configuration reloads.
+#accept_mac_file=/etc/hostapd/hostapd.accept
+#deny_mac_file=/etc/hostapd/hostapd.deny
+
+# IEEE 802.11 specifies two authentication algorithms. hostapd can be
+# configured to allow both of these or only one. Open system authentication
+# should be used with IEEE 802.1X.
+# Bit fields of allowed authentication algorithms:
+# bit 0 = Open System Authentication
+# bit 1 = Shared Key Authentication (requires WEP)
+auth_algs=1
+
+# Associate as a station to another AP while still acting as an AP on the same
+# channel.
+#assoc_ap_addr=00:12:34:56:78:9a
+
+
+##### IEEE 802.1X (and IEEE 802.1aa/D4) related configuration #################
+
+# Require IEEE 802.1X authorization
+#ieee8021x=0
+
+# Use integrated EAP authenticator instead of external RADIUS authentication
+# server
+#eap_authenticator=0
+
+# Path for EAP authenticator user database
+#eap_user_file=/etc/hostapd/eap_user
+
+# CA certificate (PEM or DER file) for EAP-TLS/PEAP/TTLS
+#ca_cert=/etc/hostapd/ca.pem
+
+# Server certificate (PEM or DER file) for EAP-TLS/PEAP/TTLS
+#server_cert=/etc/hostapd/server.pem
+
+# Private key matching with the server certificate for EAP-TLS/PEAP/TTLS
+# This may point to the same file as server_cert if both certificate and key
+# are included in a single file. PKCS#12 (PFX) file (.p12/.pfx) can also be
+# used by commenting out server_cert and specifying the PFX file as the
+# private_key.
+#private_key=/etc/hostapd/server.prv
+
+# Passphrase for private key
+#private_key_passwd=secret passphrase
+
+# Configuration data for EAP-SIM database/authentication gateway interface.
+# This is a text string in implementation specific format. The example
+# implementation in eap_sim_db.c uses this as the file name for the GSM
+# authentication triplets.
+#eap_sim_db=/etc/hostapd/sim_db
+
+# Optional displayable message sent with EAP Request-Identity
+#eap_message=hello
+
+# WEP rekeying (disabled if key lengths are not set or are set to 0)
+# Key lengths for default/broadcast and individual/unicast keys:
+# 5 = 40-bit WEP (also known as 64-bit WEP with 40 secret bits)
+# 13 = 104-bit WEP (also known as 128-bit WEP with 104 secret bits)
+#wep_key_len_broadcast=5
+#wep_key_len_unicast=5
+# Rekeying period in seconds. 0 = do not rekey (i.e., set keys only once)
+#wep_rekey_period=300
+
+# EAPOL-Key index workaround (set bit7) for WinXP Supplicant (needed only if
+# only broadcast keys are used)
+#eapol_key_index_workaround=0
+
+# EAP reauthentication period in seconds (default: 3600 seconds; 0 = disable
+# reauthentication).
+#eap_reauth_period=3600
+
+
+##### IEEE 802.11f - Inter-Access Point Protocol (IAPP) #######################
+
+# Interface to be used for IAPP broadcast packets
+#iapp_interface=eth0
+
+
+##### RADIUS configuration ####################################################
+# for IEEE 802.1X with external Authentication Server, IEEE 802.11
+# authentication with external ACL for MAC addresses, and accounting
+
+# The own IP address of the access point (used as NAS-IP-Address)
+#own_ip_addr=127.0.0.1
+
+# Optional NAS-Identifier string for RADIUS messages. When used, this should be
+# a unique to the NAS within the scope of the RADIUS server. For example, a
+# fully qualified domain name can be used here.
+#nas_identifier=ap.example.com
+
+# RADIUS authentication server
+#auth_server_addr=127.0.0.1
+#auth_server_port=1812
+#auth_server_shared_secret=secret
+
+# RADIUS accounting server
+#acct_server_addr=127.0.0.1
+#acct_server_port=1813
+#acct_server_shared_secret=secret
+
+# Secondary RADIUS servers; to be used if primary one does not reply to
+# RADIUS packets. These are optional and there can be more than one secondary
+# server listed.
+#auth_server_addr=127.0.0.2
+#auth_server_port=1812
+#auth_server_shared_secret=secret2
+#
+#acct_server_addr=127.0.0.2
+#acct_server_port=1813
+#acct_server_shared_secret=secret2
+
+# Retry interval for trying to return to the primary RADIUS server (in
+# seconds). RADIUS client code will automatically try to use the next server
+# when the current server is not replying to requests. If this interval is set,
+# primary server will be retried after configured amount of time even if the
+# currently used secondary server is still working.
+#radius_retry_primary_interval=600
+
+# Interim accounting update interval
+# If this is set (larger than 0) and acct_server is configured, hostapd will
+# send interim accounting updates every N seconds. Note: if set, this overrides
+# possible Acct-Interim-Interval attribute in Access-Accept message. Thus, this
+# value should not be configured in hostapd.conf, if RADIUS server is used to
+# control the interim interval.
+# This value should not be less 600 (10 minutes) and must not be less than
+# 60 (1 minute).
+#radius_acct_interim_interval=600
+
+# hostapd can be used as a RADIUS authentication server for other hosts. This
+# requires that the integrated EAP authenticator is also enabled and both
+# authentication services are sharing the same configuration.
+
+# File name of the RADIUS clients configuration for the RADIUS server. If this
+# commented out, RADIUS server is disabled.
+#radius_server_clients=/etc/hostapd/radius_clients
+
+# The UDP port number for the RADIUS authentication server
+#radius_server_auth_port=1812
+
+
+##### WPA/IEEE 802.11i configuration ##########################################
+
+# Enable WPA. Setting this variable configures the AP to require WPA (either
+# WPA-PSK or WPA-RADIUS/EAP based on other configuration). For WPA-PSK, either
+# wpa_psk or wpa_passphrase must be set and wpa_key_mgmt must include WPA-PSK.
+# For WPA-RADIUS/EAP, ieee8021x must be set (but without dynamic WEP keys),
+# RADIUS authentication server must be configured, and WPA-EAP must be included
+# in wpa_key_mgmt.
+# This field is a bit field that can be used to enable WPA (IEEE 802.11i/D3.0)
+# and/or WPA2 (full IEEE 802.11i/RSN):
+# bit0 = WPA
+# bit1 = IEEE 802.11i/RSN (WPA2) (dot11RSNAEnabled)
+wpa=1
+
+# WPA pre-shared keys for WPA-PSK. This can be either entered as a 256-bit
+# secret in hex format (64 hex digits), wpa_psk, or as an ASCII passphrase
+# (8..63 characters) that will be converted to PSK. This conversion uses SSID
+# so the PSK changes when ASCII passphrase is used and the SSID is changed.
+# wpa_psk (dot11RSNAConfigPSKValue)
+# wpa_passphrase (dot11RSNAConfigPSKPassPhrase)
+#wpa_psk=0123456789abcdef0123456789abcdef0123456789abcdef0123456789abcdef
+wpa_passphrase=yoursecretpassphrase
+
+# Optionally, WPA PSKs can be read from a separate text file (containing list
+# of (PSK,MAC address) pairs. This allows more than one PSK to be configured.
+# Use absolute path name to make sure that the files can be read on SIGHUP
+# configuration reloads.
+#wpa_psk_file=/etc/hostapd/wpa_psk
+
+# Set of accepted key management algorithms (WPA-PSK, WPA-EAP, or both). The
+# entries are separated with a space.
+# (dot11RSNAConfigAuthenticationSuitesTable)
+#wpa_key_mgmt=WPA-PSK WPA-EAP
+wpa_key_mgmt=WPA-PSK
+
+# Set of accepted cipher suites (encryption algorithms) for pairwise keys
+# (unicast packets). This is a space separated list of algorithms:
+
+# CCMP = AES in Counter mode with CBC-MAC [RFC 3610, IEEE 802.11i/D7.0]
+# TKIP = Temporal Key Integrity Protocol [IEEE 802.11i/D7.0]
+# Group cipher suite (encryption algorithm for broadcast and multicast frames)
+# is automatically selected based on this configuration. If only CCMP is
+# allowed as the pairwise cipher, group cipher will also be CCMP. Otherwise,
+# TKIP will be used as the group cipher.
+# (dot11RSNAConfigPairwiseCiphersTable)
+wpa_pairwise=TKIP CCMP
+
+# Time interval for rekeying GTK (broadcast/multicast encryption keys) in
+# seconds. (dot11RSNAConfigGroupRekeyTime)
+#wpa_group_rekey=600
+
+# Rekey GTK when any STA that possesses the current GTK is leaving the BSS.
+# (dot11RSNAConfigGroupRekeyStrict)
+#wpa_strict_rekey=1
+
+# Time interval for rekeying GMK (master key used internally to generate GTKs
+# (in seconds).
+#wpa_gmk_rekey=86400
+
+# Enable IEEE 802.11i/RSN/WPA2 pre-authentication. This is used to speed up
+# roaming be pre-authenticating IEEE 802.1X/EAP part of the full RSN
+# authentication and key handshake before actually associating with a new AP.
+# (dot11RSNAPreauthenticationEnabled)
+#rsn_preauth=1
+#
+# Space separated list of interfaces from which pre-authentication frames are
+# accepted (e.g., 'eth0' or 'eth0 wlan0wds0'. This list should include all
+# interface that are used for connections to other APs. This could include
+# wired interfaces and WDS links. The normal wireless data interface towards
+# associated stations (e.g., wlan0) should not be added, since
+# pre-authentication is only used with APs other than the currently associated
+# one.
+#rsn_preauth_interfaces=eth0
projects / people / pmueller / ipfire-2.x.git / blobdiff