[thirdparty/u-boot.git] / src / arm / qcom / pm8941.dtsi

// SPDX-License-Identifier: GPL-2.0
#include <dt-bindings/iio/qcom,spmi-vadc.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>


/ {
	thermal-zones {
		pm8941-thermal {
			polling-delay-passive = <100>;
			polling-delay = <0>;
			thermal-sensors = <&pm8941_temp>;

			trips {
				trip0 {
					temperature = <105000>;
					hysteresis = <2000>;
					type = "passive";
				};

				trip1 {
					temperature = <125000>;
					hysteresis = <2000>;
					type = "hot";
				};

				crit {
					temperature = <145000>;
					hysteresis = <2000>;
					type = "critical";
				};
			};
		};
	};
};

&spmi_bus {

	pm8941_0: pm8941@0 {
		compatible = "qcom,pm8941", "qcom,spmi-pmic";
		reg = <0x0 SPMI_USID>;
		#address-cells = <1>;
		#size-cells = <0>;

		rtc@6000 {
			compatible = "qcom,pm8941-rtc";
			reg = <0x6000>,
			      <0x6100>;
			reg-names = "rtc", "alarm";
			interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
		};

		pon@800 {
			compatible = "qcom,pm8941-pon";
			reg = <0x800>;

			pwrkey {
				compatible = "qcom,pm8941-pwrkey";
				interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
				debounce = <15625>;
				bias-pull-up;
			};

			pm8941_resin: resin {
				compatible = "qcom,pm8941-resin";
				interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
				debounce = <15625>;
				bias-pull-up;
				status = "disabled";
			};
		};

		usb_id: usb-detect@900 {
			compatible = "qcom,pm8941-misc";
			reg = <0x900>;
			interrupts = <0x0 0x9 0 IRQ_TYPE_EDGE_BOTH>;
			interrupt-names = "usb_id";
		};

		smbb: charger@1000 {
			compatible = "qcom,pm8941-charger";
			reg = <0x1000>;
			interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
				     <0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
				     <0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
				     <0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>,
				     <0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>,
				     <0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>,
				     <0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>,
				     <0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>;
			interrupt-names = "chg-done",
					  "chg-fast",
					  "chg-trkl",
					  "bat-temp-ok",
					  "bat-present",
					  "chg-gone",
					  "usb-valid",
					  "dc-valid";

			usb-otg-in-supply = <&pm8941_5vs1>;

			status = "disabled";

			chg_otg: otg-vbus { };
		};

		pm8941_gpios: gpio@c000 {
			compatible = "qcom,pm8941-gpio", "qcom,spmi-gpio";
			reg = <0xc000>;
			gpio-controller;
			gpio-ranges = <&pm8941_gpios 0 0 36>;
			#gpio-cells = <2>;
			interrupt-controller;
			#interrupt-cells = <2>;

			boost_bypass_n_pin: boost-bypass-state {
				pins = "gpio21";
				function = "normal";
			};
		};

		pm8941_mpps: mpps@a000 {
			compatible = "qcom,pm8941-mpp", "qcom,spmi-mpp";
			reg = <0xa000>;
			gpio-controller;
			#gpio-cells = <2>;
			gpio-ranges = <&pm8941_mpps 0 0 8>;
			interrupt-controller;
			#interrupt-cells = <2>;
		};

		pm8941_temp: temp-alarm@2400 {
			compatible = "qcom,spmi-temp-alarm";
			reg = <0x2400>;
			interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
			io-channels = <&pm8941_vadc VADC_DIE_TEMP>;
			io-channel-names = "thermal";
			#thermal-sensor-cells = <0>;
		};

		pm8941_vadc: adc@3100 {
			compatible = "qcom,spmi-vadc";
			reg = <0x3100>;
			interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
			#address-cells = <1>;
			#size-cells = <0>;
			#io-channel-cells = <1>;


			channel@6 {
				reg = <VADC_VBAT_SNS>;
			};

			channel@8 {
				reg = <VADC_DIE_TEMP>;
			};

			channel@9 {
				reg = <VADC_REF_625MV>;
			};

			channel@a {
				reg = <VADC_REF_1250MV>;
			};

			channel@e {
				reg = <VADC_GND_REF>;
			};

			channel@f {
				reg = <VADC_VDD_VADC>;
			};

			channel@30 {
				reg = <VADC_LR_MUX1_BAT_THERM>;
			};
		};

		pm8941_iadc: adc@3600 {
			compatible = "qcom,pm8941-iadc", "qcom,spmi-iadc";
			reg = <0x3600>;
			interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>;
			qcom,external-resistor-micro-ohms = <10000>;
		};

		pm8941_coincell: charger@2800 {
			compatible = "qcom,pm8941-coincell";
			reg = <0x2800>;
			status = "disabled";
		};
	};

	pm8941_1: pm8941@1 {
		compatible = "qcom,pm8941", "qcom,spmi-pmic";
		reg = <0x1 SPMI_USID>;
		#address-cells = <1>;
		#size-cells = <0>;

		pm8941_lpg: pwm {
			compatible = "qcom,pm8941-lpg";

			#address-cells = <1>;
			#size-cells = <0>;
			#pwm-cells = <2>;

			status = "disabled";
		};

		pm8941_vib: vibrator@c000 {
			compatible = "qcom,pm8916-vib";
			reg = <0xc000>;
			status = "disabled";
		};

		pm8941_wled: wled@d800 {
			compatible = "qcom,pm8941-wled";
			reg = <0xd800>;
			label = "backlight";

			status = "disabled";
		};

		regulators {
			compatible = "qcom,pm8941-regulators";
			interrupts = <0x1 0x83 0x2 0>, <0x1 0x84 0x2 0>;
			interrupt-names = "ocp-5vs1", "ocp-5vs2";
			vin_5vs-supply = <&pm8941_5v>;

			pm8941_5v: s4 {
				regulator-min-microvolt = <5000000>;
				regulator-max-microvolt = <5000000>;
				regulator-enable-ramp-delay = <500>;
			};

			pm8941_5vs1: 5vs1 {
				regulator-enable-ramp-delay = <1000>;
				regulator-pull-down;
				regulator-over-current-protection;
				qcom,ocp-max-retries = <10>;
				qcom,ocp-retry-delay = <30>;
				qcom,vs-soft-start-strength = <0>;
				regulator-initial-mode = <1>;
			};

			pm8941_5vs2: 5vs2 {
				regulator-enable-ramp-delay = <1000>;
				regulator-pull-down;
				regulator-over-current-protection;
				qcom,ocp-max-retries = <10>;
				qcom,ocp-retry-delay = <30>;
				qcom,vs-soft-start-strength = <0>;
				regulator-initial-mode = <1>;
			};
		};
	};
};
Commit	Line	Data
53633a89 TR	1	// SPDX-License-Identifier: GPL-2.0
	2	#include <dt-bindings/iio/qcom,spmi-vadc.h>
	3	#include <dt-bindings/interrupt-controller/irq.h>
	4	#include <dt-bindings/spmi/spmi.h>
	5
	6
	7	/ {
	8	thermal-zones {
	9	pm8941-thermal {
	10	polling-delay-passive = <100>;
	11	polling-delay = <0>;
	12	thermal-sensors = <&pm8941_temp>;
	13
	14	trips {
	15	trip0 {
	16	temperature = <105000>;
	17	hysteresis = <2000>;
	18	type = "passive";
	19	};
	20
	21	trip1 {
	22	temperature = <125000>;
	23	hysteresis = <2000>;
	24	type = "hot";
	25	};
	26
	27	crit {
	28	temperature = <145000>;
	29	hysteresis = <2000>;
	30	type = "critical";
	31	};
	32	};
	33	};
	34	};
	35	};
	36
	37	&spmi_bus {
	38
	39	pm8941_0: pm8941@0 {
	40	compatible = "qcom,pm8941", "qcom,spmi-pmic";
	41	reg = <0x0 SPMI_USID>;
	42	#address-cells = <1>;
	43	#size-cells = <0>;
	44
	45	rtc@6000 {
	46	compatible = "qcom,pm8941-rtc";
	47	reg = <0x6000>,
	48	<0x6100>;
	49	reg-names = "rtc", "alarm";
	50	interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
	51	};
	52
	53	pon@800 {
	54	compatible = "qcom,pm8941-pon";
	55	reg = <0x800>;
	56
	57	pwrkey {
	58	compatible = "qcom,pm8941-pwrkey";
	59	interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
	60	debounce = <15625>;
	61	bias-pull-up;
	62	};
	63
	64	pm8941_resin: resin {
65	compatible = "qcom,pm8941-resin";
66	interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
67	debounce = <15625>;
68	bias-pull-up;
69	status = "disabled";
70	};
71	};
72
73	usb_id: usb-detect@900 {
74	compatible = "qcom,pm8941-misc";
75	reg = <0x900>;
76	interrupts = <0x0 0x9 0 IRQ_TYPE_EDGE_BOTH>;
77	interrupt-names = "usb_id";
78	};
79
80	smbb: charger@1000 {
81	compatible = "qcom,pm8941-charger";
82	reg = <0x1000>;
83	interrupts = <0x0 0x10 7 IRQ_TYPE_EDGE_BOTH>,
84	<0x0 0x10 5 IRQ_TYPE_EDGE_BOTH>,
85	<0x0 0x10 4 IRQ_TYPE_EDGE_BOTH>,
86	<0x0 0x12 1 IRQ_TYPE_EDGE_BOTH>,
87	<0x0 0x12 0 IRQ_TYPE_EDGE_BOTH>,
88	<0x0 0x13 2 IRQ_TYPE_EDGE_BOTH>,
89	<0x0 0x13 1 IRQ_TYPE_EDGE_BOTH>,
90	<0x0 0x14 1 IRQ_TYPE_EDGE_BOTH>;
91	interrupt-names = "chg-done",
92	"chg-fast",
93	"chg-trkl",
94	"bat-temp-ok",
95	"bat-present",
96	"chg-gone",
97	"usb-valid",
98	"dc-valid";
99
100	usb-otg-in-supply = <&pm8941_5vs1>;
101
93743d24 TR	102	status = "disabled";
93743d24 TR	103
53633a89 TR	104	chg_otg: otg-vbus { };
	105	};
	106
	107	pm8941_gpios: gpio@c000 {
	108	compatible = "qcom,pm8941-gpio", "qcom,spmi-gpio";
	109	reg = <0xc000>;
	110	gpio-controller;
	111	gpio-ranges = <&pm8941_gpios 0 0 36>;
	112	#gpio-cells = <2>;
	113	interrupt-controller;
	114	#interrupt-cells = <2>;
	115
	116	boost_bypass_n_pin: boost-bypass-state {
	117	pins = "gpio21";
	118	function = "normal";
	119	};
	120	};
	121
	122	pm8941_mpps: mpps@a000 {
	123	compatible = "qcom,pm8941-mpp", "qcom,spmi-mpp";
	124	reg = <0xa000>;
	125	gpio-controller;
	126	#gpio-cells = <2>;
	127	gpio-ranges = <&pm8941_mpps 0 0 8>;
	128	interrupt-controller;
	129	#interrupt-cells = <2>;
	130	};
	131
	132	pm8941_temp: temp-alarm@2400 {
	133	compatible = "qcom,spmi-temp-alarm";
	134	reg = <0x2400>;
	135	interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
	136	io-channels = <&pm8941_vadc VADC_DIE_TEMP>;
	137	io-channel-names = "thermal";
	138	#thermal-sensor-cells = <0>;
	139	};
	140
	141	pm8941_vadc: adc@3100 {
	142	compatible = "qcom,spmi-vadc";
	143	reg = <0x3100>;
	144	interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
	145	#address-cells = <1>;
	146	#size-cells = <0>;
	147	#io-channel-cells = <1>;
	148
	149
	150	channel@6 {
	151	reg = <VADC_VBAT_SNS>;
	152	};
	153
	154	channel@8 {
	155	reg = <VADC_DIE_TEMP>;
	156	};
	157
	158	channel@9 {
	159	reg = <VADC_REF_625MV>;
	160	};
	161
	162	channel@a {
	163	reg = <VADC_REF_1250MV>;
	164	};
	165
	166	channel@e {
	167	reg = <VADC_GND_REF>;
168	};
169
170	channel@f {
171	reg = <VADC_VDD_VADC>;
172	};
173
174	channel@30 {
175	reg = <VADC_LR_MUX1_BAT_THERM>;
176	};
177	};
178
179	pm8941_iadc: adc@3600 {
180	compatible = "qcom,pm8941-iadc", "qcom,spmi-iadc";
181	reg = <0x3600>;
182	interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>;
183	qcom,external-resistor-micro-ohms = <10000>;
184	};
185
186	pm8941_coincell: charger@2800 {
187	compatible = "qcom,pm8941-coincell";
188	reg = <0x2800>;
189	status = "disabled";
190	};
191	};
192
193	pm8941_1: pm8941@1 {
194	compatible = "qcom,pm8941", "qcom,spmi-pmic";
195	reg = <0x1 SPMI_USID>;
196	#address-cells = <1>;
197	#size-cells = <0>;
198
199	pm8941_lpg: pwm {
200	compatible = "qcom,pm8941-lpg";
201
202	#address-cells = <1>;
203	#size-cells = <0>;
204	#pwm-cells = <2>;
205
206	status = "disabled";
207	};
208
209	pm8941_vib: vibrator@c000 {
210	compatible = "qcom,pm8916-vib";
211	reg = <0xc000>;
212	status = "disabled";
213	};
214
215	pm8941_wled: wled@d800 {
216	compatible = "qcom,pm8941-wled";
217	reg = <0xd800>;
218	label = "backlight";
219
220	status = "disabled";
221	};
222
223	regulators {
224	compatible = "qcom,pm8941-regulators";
225	interrupts = <0x1 0x83 0x2 0>, <0x1 0x84 0x2 0>;
226	interrupt-names = "ocp-5vs1", "ocp-5vs2";
227	vin_5vs-supply = <&pm8941_5v>;
228
229	pm8941_5v: s4 {
230	regulator-min-microvolt = <5000000>;
231	regulator-max-microvolt = <5000000>;
232	regulator-enable-ramp-delay = <500>;
233	};
234
235	pm8941_5vs1: 5vs1 {
236	regulator-enable-ramp-delay = <1000>;
237	regulator-pull-down;
238	regulator-over-current-protection;
239	qcom,ocp-max-retries = <10>;
240	qcom,ocp-retry-delay = <30>;
241	qcom,vs-soft-start-strength = <0>;
242	regulator-initial-mode = <1>;
243	};
244
245	pm8941_5vs2: 5vs2 {
246	regulator-enable-ramp-delay = <1000>;
247	regulator-pull-down;
248	regulator-over-current-protection;
249	qcom,ocp-max-retries = <10>;
250	qcom,ocp-retry-delay = <30>;
251	qcom,vs-soft-start-strength = <0>;
252	regulator-initial-mode = <1>;
253	};
254	};
255	};
256	};