]>
Commit | Line | Data |
---|---|---|
643ad899 SG |
1 | /* |
2 | * Copyright 2014 Zoltan HERPAI | |
3 | * Zoltan HERPAI <wigyori@uid0.hu> | |
4 | * | |
5 | * The code contained herein is licensed under the GNU General Public | |
6 | * License. You may obtain a copy of the GNU General Public License | |
7 | * Version 2 or later at the following locations: | |
8 | * | |
9 | * http://www.opensource.org/licenses/gpl-license.html | |
10 | * http://www.gnu.org/copyleft/gpl.html | |
11 | */ | |
12 | ||
13 | /dts-v1/; | |
14 | /include/ "sun7i-a20.dtsi" | |
15 | /include/ "sunxi-common-regulators.dtsi" | |
16 | #include <dt-bindings/gpio/gpio.h> | |
17 | #include <dt-bindings/input/input.h> | |
18 | ||
19 | / { | |
20 | model = "LinkSprite pcDuino3"; | |
21 | compatible = "linksprite,pcduino3", "allwinner,sun7i-a20"; | |
22 | ||
1a81cf83 SG |
23 | chosen { |
24 | stdout-path = &uart0; | |
25 | }; | |
26 | ||
643ad899 SG |
27 | soc@01c00000 { |
28 | mmc0: mmc@01c0f000 { | |
29 | pinctrl-names = "default"; | |
30 | pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin_reference_design>; | |
31 | vmmc-supply = <®_vcc3v3>; | |
32 | bus-width = <4>; | |
33 | cd-gpios = <&pio 7 1 0>; /* PH1 */ | |
34 | cd-inverted; | |
35 | status = "okay"; | |
36 | }; | |
37 | ||
38 | usbphy: phy@01c13400 { | |
39 | usb1_vbus-supply = <®_usb1_vbus>; | |
40 | usb2_vbus-supply = <®_usb2_vbus>; | |
41 | status = "okay"; | |
42 | }; | |
43 | ||
44 | ehci0: usb@01c14000 { | |
45 | status = "okay"; | |
46 | }; | |
47 | ||
48 | ohci0: usb@01c14400 { | |
49 | status = "okay"; | |
50 | }; | |
51 | ||
52 | ahci: sata@01c18000 { | |
53 | target-supply = <®_ahci_5v>; | |
54 | status = "okay"; | |
55 | }; | |
56 | ||
57 | ehci1: usb@01c1c000 { | |
58 | status = "okay"; | |
59 | }; | |
60 | ||
61 | ohci1: usb@01c1c400 { | |
62 | status = "okay"; | |
63 | }; | |
64 | ||
65 | pinctrl@01c20800 { | |
66 | ahci_pwr_pin_a: ahci_pwr_pin@0 { | |
67 | allwinner,pins = "PH2"; | |
68 | }; | |
69 | ||
70 | led_pins_pcduino3: led_pins@0 { | |
71 | allwinner,pins = "PH15", "PH16"; | |
72 | allwinner,function = "gpio_out"; | |
73 | allwinner,drive = <0>; | |
74 | allwinner,pull = <0>; | |
75 | }; | |
76 | ||
77 | key_pins_pcduino3: key_pins@0 { | |
78 | allwinner,pins = "PH17", "PH18", "PH19"; | |
79 | allwinner,function = "gpio_in"; | |
80 | allwinner,drive = <0>; | |
81 | allwinner,pull = <0>; | |
82 | }; | |
83 | }; | |
84 | ||
85 | ir0: ir@01c21800 { | |
86 | pinctrl-names = "default"; | |
87 | pinctrl-0 = <&ir0_pins_a>; | |
88 | status = "okay"; | |
89 | }; | |
90 | ||
91 | uart0: serial@01c28000 { | |
92 | pinctrl-names = "default"; | |
93 | pinctrl-0 = <&uart0_pins_a>; | |
94 | status = "okay"; | |
95 | }; | |
96 | ||
97 | i2c0: i2c@01c2ac00 { | |
98 | pinctrl-names = "default"; | |
99 | pinctrl-0 = <&i2c0_pins_a>; | |
100 | status = "okay"; | |
101 | ||
102 | axp209: pmic@34 { | |
103 | compatible = "x-powers,axp209"; | |
104 | reg = <0x34>; | |
105 | interrupt-parent = <&nmi_intc>; | |
106 | interrupts = <0 8>; | |
107 | ||
108 | interrupt-controller; | |
109 | #interrupt-cells = <1>; | |
110 | }; | |
111 | }; | |
112 | ||
113 | gmac: ethernet@01c50000 { | |
114 | pinctrl-names = "default"; | |
115 | pinctrl-0 = <&gmac_pins_mii_a>; | |
116 | phy = <&phy1>; | |
117 | phy-mode = "mii"; | |
118 | status = "okay"; | |
119 | ||
120 | phy1: ethernet-phy@1 { | |
121 | reg = <1>; | |
122 | }; | |
123 | }; | |
124 | }; | |
125 | ||
126 | leds { | |
127 | compatible = "gpio-leds"; | |
128 | pinctrl-names = "default"; | |
129 | pinctrl-0 = <&led_pins_pcduino3>; | |
130 | ||
131 | tx { | |
132 | label = "pcduino3:green:tx"; | |
133 | gpios = <&pio 7 15 GPIO_ACTIVE_LOW>; | |
134 | }; | |
135 | ||
136 | rx { | |
137 | label = "pcduino3:green:rx"; | |
138 | gpios = <&pio 7 16 GPIO_ACTIVE_LOW>; | |
139 | }; | |
140 | }; | |
141 | ||
142 | gpio_keys { | |
143 | compatible = "gpio-keys"; | |
144 | pinctrl-names = "default"; | |
145 | pinctrl-0 = <&key_pins_pcduino3>; | |
146 | #address-cells = <1>; | |
147 | #size-cells = <0>; | |
148 | button@0 { | |
149 | label = "Key Back"; | |
150 | linux,code = <KEY_BACK>; | |
151 | gpios = <&pio 7 17 GPIO_ACTIVE_LOW>; | |
152 | }; | |
153 | button@1 { | |
154 | label = "Key Home"; | |
155 | linux,code = <KEY_HOME>; | |
156 | gpios = <&pio 7 18 GPIO_ACTIVE_LOW>; | |
157 | }; | |
158 | button@2 { | |
159 | label = "Key Menu"; | |
160 | linux,code = <KEY_MENU>; | |
161 | gpios = <&pio 7 19 GPIO_ACTIVE_LOW>; | |
162 | }; | |
163 | }; | |
164 | ||
165 | reg_usb1_vbus: usb1-vbus { | |
166 | status = "okay"; | |
167 | }; | |
168 | ||
169 | reg_usb2_vbus: usb2-vbus { | |
170 | status = "okay"; | |
171 | }; | |
172 | ||
173 | reg_ahci_5v: ahci-5v { | |
174 | gpio = <&pio 7 2 0>; | |
175 | status = "okay"; | |
176 | }; | |
177 | }; |