]>
Commit | Line | Data |
---|---|---|
83d290c5 | 1 | # SPDX-License-Identifier: GPL-2.0+ |
38041db7 EC |
2 | # |
3 | # Copyright (C) 2010 Eric C. Cooper <ecc@cmu.edu> | |
4 | # | |
5 | # Based on sheevaplug/kwbimage.cfg originally written by | |
6 | # Prafulla Wadaskar <prafulla@marvell.com> | |
7 | # (C) Copyright 2009 | |
8 | # Marvell Semiconductor <www.marvell.com> | |
b1e6c4c3 | 9 | # Refer doc/README.kwbimage for more details about how-to configure |
38041db7 EC |
10 | # and create kirkwood boot image |
11 | # | |
12 | ||
13 | # Boot Media configurations | |
14 | BOOT_FROM nand | |
15 | NAND_ECC_MODE default | |
16 | NAND_PAGE_SIZE 0x0800 | |
17 | ||
18 | # SOC registers configuration using bootrom header extension | |
19 | # Maximum KWBIMAGE_MAX_CONFIG configurations allowed | |
20 | ||
21 | # Configure RGMII-0 interface pad voltage to 1.8V | |
22 | DATA 0xFFD100e0 0x1b1b1b9b | |
23 | ||
24 | #Dram initalization for SINGLE x16 CL=5 @ 400MHz | |
25 | DATA 0xFFD01400 0x43000c30 # DDR Configuration register | |
26 | # bit13-0: 0xc30 (3120 DDR2 clks refresh rate) | |
27 | # bit23-14: zero | |
28 | # bit24: 1= enable exit self refresh mode on DDR access | |
29 | # bit25: 1 required | |
30 | # bit29-26: zero | |
31 | # bit31-30: 01 | |
32 | ||
33 | DATA 0xFFD01404 0x37543000 # DDR Controller Control Low | |
34 | # bit 4: 0=addr/cmd in smame cycle | |
35 | # bit 5: 0=clk is driven during self refresh, we don't care for APX | |
36 | # bit 6: 0=use recommended falling edge of clk for addr/cmd | |
37 | # bit14: 0=input buffer always powered up | |
38 | # bit18: 1=cpu lock transaction enabled | |
39 | # bit23-20: 5=recommended value for CL=5 and STARTBURST_DEL disabled bit31=0 | |
40 | # bit27-24: 7= CL+2, STARTBURST sample stages, for freqs 400MHz, unbuffered DIMM | |
41 | # bit30-28: 3 required | |
42 | # bit31: 0=no additional STARTBURST delay | |
43 | ||
44 | DATA 0xFFD01408 0x22125451 # DDR Timing (Low) (active cycles value +1) | |
45 | # bit3-0: TRAS lsbs | |
46 | # bit7-4: TRCD | |
47 | # bit11- 8: TRP | |
48 | # bit15-12: TWR | |
49 | # bit19-16: TWTR | |
50 | # bit20: TRAS msb | |
51 | # bit23-21: 0x0 | |
52 | # bit27-24: TRRD | |
53 | # bit31-28: TRTP | |
54 | ||
55 | DATA 0xFFD0140C 0x00000a33 # DDR Timing (High) | |
56 | # bit6-0: TRFC | |
57 | # bit8-7: TR2R | |
58 | # bit10-9: TR2W | |
59 | # bit12-11: TW2W | |
60 | # bit31-13: zero required | |
61 | ||
62 | DATA 0xFFD01410 0x0000000d # DDR Address Control | |
63 | # bit1-0: 00, Cs0width=x8 | |
64 | # bit3-2: 11, Cs0size=1Gb | |
65 | # bit5-4: 00, Cs1width=nonexistent | |
66 | # bit7-6: 00, Cs1size =nonexistent | |
67 | # bit9-8: 00, Cs2width=nonexistent | |
68 | # bit11-10: 00, Cs2size =nonexistent | |
69 | # bit13-12: 00, Cs3width=nonexistent | |
70 | # bit15-14: 00, Cs3size =nonexistent | |
71 | # bit16: 0, Cs0AddrSel | |
72 | # bit17: 0, Cs1AddrSel | |
73 | # bit18: 0, Cs2AddrSel | |
74 | # bit19: 0, Cs3AddrSel | |
75 | # bit31-20: 0 required | |
76 | ||
77 | DATA 0xFFD01414 0x00000000 # DDR Open Pages Control | |
78 | # bit0: 0, OpenPage enabled | |
79 | # bit31-1: 0 required | |
80 | ||
81 | DATA 0xFFD01418 0x00000000 # DDR Operation | |
82 | # bit3-0: 0x0, DDR cmd | |
83 | # bit31-4: 0 required | |
84 | ||
85 | DATA 0xFFD0141C 0x00000C52 # DDR Mode | |
86 | # bit2-0: 2, BurstLen=2 required | |
87 | # bit3: 0, BurstType=0 required | |
88 | # bit6-4: 4, CL=5 | |
89 | # bit7: 0, TestMode=0 normal | |
90 | # bit8: 0, DLL reset=0 normal | |
91 | # bit11-9: 6, auto-precharge write recovery ???????????? | |
92 | # bit12: 0, PD must be zero | |
93 | # bit31-13: 0 required | |
94 | ||
95 | DATA 0xFFD01420 0x00000040 # DDR Extended Mode | |
96 | # bit0: 0, DDR DLL enabled | |
97 | # bit1: 0, DDR drive strenght normal | |
98 | # bit2: 0, DDR ODT control lsd (disabled) | |
99 | # bit5-3: 000, required | |
100 | # bit6: 1, DDR ODT control msb, (disabled) | |
101 | # bit9-7: 000, required | |
102 | # bit10: 0, differential DQS enabled | |
103 | # bit11: 0, required | |
104 | # bit12: 0, DDR output buffer enabled | |
105 | # bit31-13: 0 required | |
106 | ||
107 | DATA 0xFFD01424 0x0000F17F # DDR Controller Control High | |
108 | # bit2-0: 111, required | |
109 | # bit3 : 1 , MBUS Burst Chop disabled | |
110 | # bit6-4: 111, required | |
111 | # bit7 : 0 | |
112 | # bit8 : 1 , add writepath sample stage, must be 1 for DDR freq >= 300MHz | |
113 | # bit9 : 0 , no half clock cycle addition to dataout | |
114 | # bit10 : 0 , 1/4 clock cycle skew enabled for addr/ctl signals | |
115 | # bit11 : 0 , 1/4 clock cycle skew disabled for write mesh | |
116 | # bit15-12: 1111 required | |
117 | # bit31-16: 0 required | |
118 | ||
119 | DATA 0xFFD01428 0x00085520 # DDR2 ODT Read Timing (default values) | |
120 | DATA 0xFFD0147C 0x00008552 # DDR2 ODT Write Timing (default values) | |
121 | ||
122 | DATA 0xFFD01500 0x00000000 # CS[0]n Base address to 0x0 | |
123 | DATA 0xFFD01504 0x07FFFFF1 # CS[0]n Size | |
124 | # bit0: 1, Window enabled | |
125 | # bit1: 0, Write Protect disabled | |
126 | # bit3-2: 00, CS0 hit selected | |
127 | # bit23-4: ones, required | |
128 | # bit31-24: 0x07, Size (i.e. 128MB) | |
129 | ||
130 | DATA 0xFFD01508 0x10000000 # CS[1]n Base address to 256Mb | |
131 | DATA 0xFFD0150C 0x00000000 # CS[1]n Size, window disabled | |
132 | ||
133 | DATA 0xFFD01514 0x00000000 # CS[2]n Size, window disabled | |
134 | DATA 0xFFD0151C 0x00000000 # CS[3]n Size, window disabled | |
135 | ||
136 | DATA 0xFFD01494 0x00030000 # DDR ODT Control (Low) | |
137 | DATA 0xFFD01498 0x00000000 # DDR ODT Control (High) | |
138 | # bit1-0: 00, ODT0 controlled by ODT Control (low) register above | |
139 | # bit3-2: 01, ODT1 active NEVER! | |
140 | # bit31-4: zero, required | |
141 | ||
142 | DATA 0xFFD0149C 0x0000E803 # CPU ODT Control | |
143 | DATA 0xFFD01480 0x00000001 # DDR Initialization Control | |
144 | #bit0=1, enable DDR init upon this register write | |
145 | ||
146 | # End of Header extension | |
147 | DATA 0x0 0x0 |