[people/ms/linux.git] / drivers / ata / pata_hpt366.c

/*
 * Libata driver for the highpoint 366 and 368 UDMA66 ATA controllers.
 *
 * This driver is heavily based upon:
 *
 * linux/drivers/ide/pci/hpt366.c		Version 0.36	April 25, 2003
 *
 * Copyright (C) 1999-2003		Andre Hedrick <andre@linux-ide.org>
 * Portions Copyright (C) 2001	        Sun Microsystems, Inc.
 * Portions Copyright (C) 2003		Red Hat Inc
 *
 *
 * TODO
 *	Maybe PLL mode
 *	Look into engine reset on timeout errors. Should not be
 *		required.
 */


#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>

#define DRV_NAME	"pata_hpt366"
#define DRV_VERSION	"0.6.2"

struct hpt_clock {
	u8	xfer_speed;
	u32	timing;
};

/* key for bus clock timings
 * bit
 * 0:3    data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW
 *        DMA. cycles = value + 1
 * 4:8    data_low_time. active time of DIOW_/DIOR_ for PIO and MW
 *        DMA. cycles = value + 1
 * 9:12   cmd_high_time. inactive time of DIOW_/DIOR_ during task file
 *        register access.
 * 13:17  cmd_low_time. active time of DIOW_/DIOR_ during task file
 *        register access.
 * 18:21  udma_cycle_time. clock freq and clock cycles for UDMA xfer.
 *        during task file register access.
 * 22:24  pre_high_time. time to initialize 1st cycle for PIO and MW DMA
 *        xfer.
 * 25:27  cmd_pre_high_time. time to initialize 1st PIO cycle for task
 *        register access.
 * 28     UDMA enable
 * 29     DMA enable
 * 30     PIO_MST enable. if set, the chip is in bus master mode during
 *        PIO.
 * 31     FIFO enable.
 */

static const struct hpt_clock hpt366_40[] = {
	{	XFER_UDMA_4,	0x900fd943	},
	{	XFER_UDMA_3,	0x900ad943	},
	{	XFER_UDMA_2,	0x900bd943	},
	{	XFER_UDMA_1,	0x9008d943	},
	{	XFER_UDMA_0,	0x9008d943	},

	{	XFER_MW_DMA_2,	0xa008d943	},
	{	XFER_MW_DMA_1,	0xa010d955	},
	{	XFER_MW_DMA_0,	0xa010d9fc	},

	{	XFER_PIO_4,	0xc008d963	},
	{	XFER_PIO_3,	0xc010d974	},
	{	XFER_PIO_2,	0xc010d997	},
	{	XFER_PIO_1,	0xc010d9c7	},
	{	XFER_PIO_0,	0xc018d9d9	},
	{	0,		0x0120d9d9	}
};

static const struct hpt_clock hpt366_33[] = {
	{	XFER_UDMA_4,	0x90c9a731	},
	{	XFER_UDMA_3,	0x90cfa731	},
	{	XFER_UDMA_2,	0x90caa731	},
	{	XFER_UDMA_1,	0x90cba731	},
	{	XFER_UDMA_0,	0x90c8a731	},

	{	XFER_MW_DMA_2,	0xa0c8a731	},
	{	XFER_MW_DMA_1,	0xa0c8a732	},	/* 0xa0c8a733 */
	{	XFER_MW_DMA_0,	0xa0c8a797	},

	{	XFER_PIO_4,	0xc0c8a731	},
	{	XFER_PIO_3,	0xc0c8a742	},
	{	XFER_PIO_2,	0xc0d0a753	},
	{	XFER_PIO_1,	0xc0d0a7a3	},	/* 0xc0d0a793 */
	{	XFER_PIO_0,	0xc0d0a7aa	},	/* 0xc0d0a7a7 */
	{	0,		0x0120a7a7	}
};

static const struct hpt_clock hpt366_25[] = {
	{	XFER_UDMA_4,	0x90c98521	},
	{	XFER_UDMA_3,	0x90cf8521	},
	{	XFER_UDMA_2,	0x90cf8521	},
	{	XFER_UDMA_1,	0x90cb8521	},
	{	XFER_UDMA_0,	0x90cb8521	},

	{	XFER_MW_DMA_2,	0xa0ca8521	},
	{	XFER_MW_DMA_1,	0xa0ca8532	},
	{	XFER_MW_DMA_0,	0xa0ca8575	},

	{	XFER_PIO_4,	0xc0ca8521	},
	{	XFER_PIO_3,	0xc0ca8532	},
	{	XFER_PIO_2,	0xc0ca8542	},
	{	XFER_PIO_1,	0xc0d08572	},
	{	XFER_PIO_0,	0xc0d08585	},
	{	0,		0x01208585	}
};

static const char *bad_ata33[] = {
	"Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3", "Maxtor 90845U3", "Maxtor 90650U2",
	"Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5", "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2",
	"Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6", "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4",
	"Maxtor 90510D4",
	"Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2",
	"Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7", "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4",
	"Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5", "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2",
	NULL
};

static const char *bad_ata66_4[] = {
	"IBM-DTLA-307075",
	"IBM-DTLA-307060",
	"IBM-DTLA-307045",
	"IBM-DTLA-307030",
	"IBM-DTLA-307020",
	"IBM-DTLA-307015",
	"IBM-DTLA-305040",
	"IBM-DTLA-305030",
	"IBM-DTLA-305020",
	"IC35L010AVER07-0",
	"IC35L020AVER07-0",
	"IC35L030AVER07-0",
	"IC35L040AVER07-0",
	"IC35L060AVER07-0",
	"WDC AC310200R",
	NULL
};

static const char *bad_ata66_3[] = {
	"WDC AC310200R",
	NULL
};

static int hpt_dma_blacklisted(const struct ata_device *dev, char *modestr, const char *list[])
{
	unsigned char model_num[ATA_ID_PROD_LEN + 1];
	int i = 0;

	ata_id_c_string(dev->id, model_num, ATA_ID_PROD, sizeof(model_num));

	while (list[i] != NULL) {
		if (!strcmp(list[i], model_num)) {
			printk(KERN_WARNING DRV_NAME ": %s is not supported for %s.\n",
				modestr, list[i]);
			return 1;
		}
		i++;
	}
	return 0;
}

/**
 *	hpt366_filter	-	mode selection filter
 *	@adev: ATA device
 *
 *	Block UDMA on devices that cause trouble with this controller.
 */

static unsigned long hpt366_filter(struct ata_device *adev, unsigned long mask)
{
	if (adev->class == ATA_DEV_ATA) {
		if (hpt_dma_blacklisted(adev, "UDMA",  bad_ata33))
			mask &= ~ATA_MASK_UDMA;
		if (hpt_dma_blacklisted(adev, "UDMA3", bad_ata66_3))
			mask &= ~(0xF8 << ATA_SHIFT_UDMA);
		if (hpt_dma_blacklisted(adev, "UDMA4", bad_ata66_4))
			mask &= ~(0xF0 << ATA_SHIFT_UDMA);
	}
	return ata_pci_default_filter(adev, mask);
}

/**
 *	hpt36x_find_mode	-	reset the hpt36x bus
 *	@ap: ATA port
 *	@speed: transfer mode
 *
 *	Return the 32bit register programming information for this channel
 *	that matches the speed provided.
 */

static u32 hpt36x_find_mode(struct ata_port *ap, int speed)
{
	struct hpt_clock *clocks = ap->host->private_data;

	while(clocks->xfer_speed) {
		if (clocks->xfer_speed == speed)
			return clocks->timing;
		clocks++;
	}
	BUG();
	return 0xffffffffU;	/* silence compiler warning */
}

static int hpt36x_cable_detect(struct ata_port *ap)
{
	u8 ata66;
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);

	pci_read_config_byte(pdev, 0x5A, &ata66);
	if (ata66 & (1 << ap->port_no))
		return ATA_CBL_PATA40;
	return ATA_CBL_PATA80;
}

/**
 *	hpt366_set_piomode		-	PIO setup
 *	@ap: ATA interface
 *	@adev: device on the interface
 *
 *	Perform PIO mode setup.
 */

static void hpt366_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	u32 addr1, addr2;
	u32 reg;
	u32 mode;
	u8 fast;

	addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
	addr2 = 0x51 + 4 * ap->port_no;

	/* Fast interrupt prediction disable, hold off interrupt disable */
	pci_read_config_byte(pdev, addr2, &fast);
	if (fast & 0x80) {
		fast &= ~0x80;
		pci_write_config_byte(pdev, addr2, fast);
	}

	pci_read_config_dword(pdev, addr1, &reg);
	mode = hpt36x_find_mode(ap, adev->pio_mode);
	mode &= ~0x8000000;	/* No FIFO in PIO */
	mode &= ~0x30070000;	/* Leave config bits alone */
	reg &= 0x30070000;	/* Strip timing bits */
	pci_write_config_dword(pdev, addr1, reg | mode);
}

/**
 *	hpt366_set_dmamode		-	DMA timing setup
 *	@ap: ATA interface
 *	@adev: Device being configured
 *
 *	Set up the channel for MWDMA or UDMA modes. Much the same as with
 *	PIO, load the mode number and then set MWDMA or UDMA flag.
 */

static void hpt366_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	u32 addr1, addr2;
	u32 reg;
	u32 mode;
	u8 fast;

	addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
	addr2 = 0x51 + 4 * ap->port_no;

	/* Fast interrupt prediction disable, hold off interrupt disable */
	pci_read_config_byte(pdev, addr2, &fast);
	if (fast & 0x80) {
		fast &= ~0x80;
		pci_write_config_byte(pdev, addr2, fast);
	}

	pci_read_config_dword(pdev, addr1, &reg);
	mode = hpt36x_find_mode(ap, adev->dma_mode);
	mode |= 0x8000000;	/* FIFO in MWDMA or UDMA */
	mode &= ~0xC0000000;	/* Leave config bits alone */
	reg &= 0xC0000000;	/* Strip timing bits */
	pci_write_config_dword(pdev, addr1, reg | mode);
}

static struct scsi_host_template hpt36x_sht = {
	ATA_BMDMA_SHT(DRV_NAME),
};

/*
 *	Configuration for HPT366/68
 */

static struct ata_port_operations hpt366_port_ops = {
	.set_piomode	= hpt366_set_piomode,
	.set_dmamode	= hpt366_set_dmamode,
	.mode_filter	= hpt366_filter,

	.tf_load	= ata_tf_load,
	.tf_read	= ata_tf_read,
	.check_status 	= ata_check_status,
	.exec_command	= ata_exec_command,
	.dev_select 	= ata_std_dev_select,

	.freeze		= ata_bmdma_freeze,
	.thaw		= ata_bmdma_thaw,
	.error_handler	= ata_bmdma_error_handler,
	.post_internal_cmd = ata_bmdma_post_internal_cmd,
	.cable_detect	= hpt36x_cable_detect,

	.bmdma_setup 	= ata_bmdma_setup,
	.bmdma_start 	= ata_bmdma_start,
	.bmdma_stop	= ata_bmdma_stop,
	.bmdma_status 	= ata_bmdma_status,

	.qc_prep 	= ata_qc_prep,
	.qc_issue	= ata_qc_issue_prot,

	.data_xfer	= ata_data_xfer,

	.irq_handler	= ata_interrupt,
	.irq_clear	= ata_bmdma_irq_clear,
	.irq_on		= ata_irq_on,

	.port_start	= ata_sff_port_start,
};

/**
 *	hpt36x_init_chipset	-	common chip setup
 *	@dev: PCI device
 *
 *	Perform the chip setup work that must be done at both init and
 *	resume time
 */

static void hpt36x_init_chipset(struct pci_dev *dev)
{
	u8 drive_fast;
	pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
	pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
	pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
	pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);

	pci_read_config_byte(dev, 0x51, &drive_fast);
	if (drive_fast & 0x80)
		pci_write_config_byte(dev, 0x51, drive_fast & ~0x80);
}

/**
 *	hpt36x_init_one		-	Initialise an HPT366/368
 *	@dev: PCI device
 *	@id: Entry in match table
 *
 *	Initialise an HPT36x device. There are some interesting complications
 *	here. Firstly the chip may report 366 and be one of several variants.
 *	Secondly all the timings depend on the clock for the chip which we must
 *	detect and look up
 *
 *	This is the known chip mappings. It may be missing a couple of later
 *	releases.
 *
 *	Chip version		PCI		Rev	Notes
 *	HPT366			4 (HPT366)	0	UDMA66
 *	HPT366			4 (HPT366)	1	UDMA66
 *	HPT368			4 (HPT366)	2	UDMA66
 *	HPT37x/30x		4 (HPT366)	3+	Other driver
 *
 */

static int hpt36x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
{
	static const struct ata_port_info info_hpt366 = {
		.sht = &hpt36x_sht,
		.flags = ATA_FLAG_SLAVE_POSS,
		.pio_mask = 0x1f,
		.mwdma_mask = 0x07,
		.udma_mask = ATA_UDMA4,
		.port_ops = &hpt366_port_ops
	};
	struct ata_port_info info = info_hpt366;
	const struct ata_port_info *ppi[] = { &info, NULL };

	u32 class_rev;
	u32 reg1;
	int rc;

	rc = pcim_enable_device(dev);
	if (rc)
		return rc;

	pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
	class_rev &= 0xFF;

	/* May be a later chip in disguise. Check */
	/* Newer chips are not in the HPT36x driver. Ignore them */
	if (class_rev > 2)
			return -ENODEV;

	hpt36x_init_chipset(dev);

	pci_read_config_dword(dev, 0x40,  &reg1);

	/* PCI clocking determines the ATA timing values to use */
	/* info_hpt366 is safe against re-entry so we can scribble on it */
	switch((reg1 & 0x700) >> 8) {
		case 5:
			info.private_data = &hpt366_40;
			break;
		case 9:
			info.private_data = &hpt366_25;
			break;
		default:
			info.private_data = &hpt366_33;
			break;
	}
	/* Now kick off ATA set up */
	return ata_pci_init_one(dev, ppi);
}

#ifdef CONFIG_PM
static int hpt36x_reinit_one(struct pci_dev *dev)
{
	struct ata_host *host = dev_get_drvdata(&dev->dev);
	int rc;

	rc = ata_pci_device_do_resume(dev);
	if (rc)
		return rc;
	hpt36x_init_chipset(dev);
	ata_host_resume(host);
	return 0;
}
#endif

static const struct pci_device_id hpt36x[] = {
	{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), },
	{ },
};

static struct pci_driver hpt36x_pci_driver = {
	.name 		= DRV_NAME,
	.id_table	= hpt36x,
	.probe 		= hpt36x_init_one,
	.remove		= ata_pci_remove_one,
#ifdef CONFIG_PM
	.suspend	= ata_pci_device_suspend,
	.resume		= hpt36x_reinit_one,
#endif
};

static int __init hpt36x_init(void)
{
	return pci_register_driver(&hpt36x_pci_driver);
}

static void __exit hpt36x_exit(void)
{
	pci_unregister_driver(&hpt36x_pci_driver);
}

MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for the Highpoint HPT366/368");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, hpt36x);
MODULE_VERSION(DRV_VERSION);

module_init(hpt36x_init);
module_exit(hpt36x_exit);
Commit	Line	Data
669a5db4 JG	1	/*
	2	* Libata driver for the highpoint 366 and 368 UDMA66 ATA controllers.
	3	*
	4	* This driver is heavily based upon:
	5	*
	6	* linux/drivers/ide/pci/hpt366.c Version 0.36 April 25, 2003
	7	*
	8	* Copyright (C) 1999-2003 Andre Hedrick <andre@linux-ide.org>
	9	* Portions Copyright (C) 2001 Sun Microsystems, Inc.
	10	* Portions Copyright (C) 2003 Red Hat Inc
	11	*
	12	*
	13	* TODO
	14	* Maybe PLL mode
	15	* Look into engine reset on timeout errors. Should not be
	16	* required.
	17	*/
	18
	19
	20	#include <linux/kernel.h>
	21	#include <linux/module.h>
	22	#include <linux/pci.h>
	23	#include <linux/init.h>
	24	#include <linux/blkdev.h>
	25	#include <linux/delay.h>
	26	#include <scsi/scsi_host.h>
	27	#include <linux/libata.h>
	28
	29	#define DRV_NAME "pata_hpt366"
6ddd6861	30	#define DRV_VERSION "0.6.2"
669a5db4 JG	31
	32	struct hpt_clock {
	33	u8 xfer_speed;
	34	u32 timing;
	35	};
	36
	37	/* key for bus clock timings
	38	* bit
	39	* 0:3 data_high_time. inactive time of DIOW_/DIOR_ for PIO and MW
	40	* DMA. cycles = value + 1
	41	* 4:8 data_low_time. active time of DIOW_/DIOR_ for PIO and MW
	42	* DMA. cycles = value + 1
	43	* 9:12 cmd_high_time. inactive time of DIOW_/DIOR_ during task file
	44	* register access.
	45	* 13:17 cmd_low_time. active time of DIOW_/DIOR_ during task file
	46	* register access.
	47	* 18:21 udma_cycle_time. clock freq and clock cycles for UDMA xfer.
	48	* during task file register access.
	49	* 22:24 pre_high_time. time to initialize 1st cycle for PIO and MW DMA
	50	* xfer.
	51	* 25:27 cmd_pre_high_time. time to initialize 1st PIO cycle for task
	52	* register access.
	53	* 28 UDMA enable
	54	* 29 DMA enable
	55	* 30 PIO_MST enable. if set, the chip is in bus master mode during
	56	* PIO.
	57	* 31 FIFO enable.
	58	*/
	59
	60	static const struct hpt_clock hpt366_40[] = {
	61	{ XFER_UDMA_4, 0x900fd943 },
	62	{ XFER_UDMA_3, 0x900ad943 },
	63	{ XFER_UDMA_2, 0x900bd943 },
	64	{ XFER_UDMA_1, 0x9008d943 },
	65	{ XFER_UDMA_0, 0x9008d943 },
	66
	67	{ XFER_MW_DMA_2, 0xa008d943 },
	68	{ XFER_MW_DMA_1, 0xa010d955 },
	69	{ XFER_MW_DMA_0, 0xa010d9fc },
	70
	71	{ XFER_PIO_4, 0xc008d963 },
	72	{ XFER_PIO_3, 0xc010d974 },
	73	{ XFER_PIO_2, 0xc010d997 },
	74	{ XFER_PIO_1, 0xc010d9c7 },
	75	{ XFER_PIO_0, 0xc018d9d9 },
	76	{ 0, 0x0120d9d9 }
	77	};
	78
	79	static const struct hpt_clock hpt366_33[] = {
	80	{ XFER_UDMA_4, 0x90c9a731 },
	81	{ XFER_UDMA_3, 0x90cfa731 },
	82	{ XFER_UDMA_2, 0x90caa731 },
	83	{ XFER_UDMA_1, 0x90cba731 },
	84	{ XFER_UDMA_0, 0x90c8a731 },
	85
	86	{ XFER_MW_DMA_2, 0xa0c8a731 },
	87	{ XFER_MW_DMA_1, 0xa0c8a732 }, /* 0xa0c8a733 */
	88	{ XFER_MW_DMA_0, 0xa0c8a797 },
	89
	90	{ XFER_PIO_4, 0xc0c8a731 },
	91	{ XFER_PIO_3, 0xc0c8a742 },
	92	{ XFER_PIO_2, 0xc0d0a753 },
	93	{ XFER_PIO_1, 0xc0d0a7a3 }, /* 0xc0d0a793 */
	94	{ XFER_PIO_0, 0xc0d0a7aa }, /* 0xc0d0a7a7 */
95	{ 0, 0x0120a7a7 }
96	};
97
98	static const struct hpt_clock hpt366_25[] = {
99	{ XFER_UDMA_4, 0x90c98521 },
100	{ XFER_UDMA_3, 0x90cf8521 },
101	{ XFER_UDMA_2, 0x90cf8521 },
102	{ XFER_UDMA_1, 0x90cb8521 },
103	{ XFER_UDMA_0, 0x90cb8521 },
104
105	{ XFER_MW_DMA_2, 0xa0ca8521 },
106	{ XFER_MW_DMA_1, 0xa0ca8532 },
107	{ XFER_MW_DMA_0, 0xa0ca8575 },
108
109	{ XFER_PIO_4, 0xc0ca8521 },
110	{ XFER_PIO_3, 0xc0ca8532 },
111	{ XFER_PIO_2, 0xc0ca8542 },
112	{ XFER_PIO_1, 0xc0d08572 },
113	{ XFER_PIO_0, 0xc0d08585 },
114	{ 0, 0x01208585 }
115	};
116
117	static const char *bad_ata33[] = {
118	"Maxtor 92720U8", "Maxtor 92040U6", "Maxtor 91360U4", "Maxtor 91020U3", "Maxtor 90845U3", "Maxtor 90650U2",
119	"Maxtor 91360D8", "Maxtor 91190D7", "Maxtor 91020D6", "Maxtor 90845D5", "Maxtor 90680D4", "Maxtor 90510D3", "Maxtor 90340D2",
120	"Maxtor 91152D8", "Maxtor 91008D7", "Maxtor 90845D6", "Maxtor 90840D6", "Maxtor 90720D5", "Maxtor 90648D5", "Maxtor 90576D4",
121	"Maxtor 90510D4",
122	"Maxtor 90432D3", "Maxtor 90288D2", "Maxtor 90256D2",
123	"Maxtor 91000D8", "Maxtor 90910D8", "Maxtor 90875D7", "Maxtor 90840D7", "Maxtor 90750D6", "Maxtor 90625D5", "Maxtor 90500D4",
124	"Maxtor 91728D8", "Maxtor 91512D7", "Maxtor 91303D6", "Maxtor 91080D5", "Maxtor 90845D4", "Maxtor 90680D4", "Maxtor 90648D3", "Maxtor 90432D2",
125	NULL
126	};
127
128	static const char *bad_ata66_4[] = {
129	"IBM-DTLA-307075",
130	"IBM-DTLA-307060",
131	"IBM-DTLA-307045",
132	"IBM-DTLA-307030",
133	"IBM-DTLA-307020",
134	"IBM-DTLA-307015",
135	"IBM-DTLA-305040",
136	"IBM-DTLA-305030",
137	"IBM-DTLA-305020",
138	"IC35L010AVER07-0",
139	"IC35L020AVER07-0",
140	"IC35L030AVER07-0",
141	"IC35L040AVER07-0",
142	"IC35L060AVER07-0",
143	"WDC AC310200R",
144	NULL
145	};
146
147	static const char *bad_ata66_3[] = {
148	"WDC AC310200R",
149	NULL
150	};
151
152	static int hpt_dma_blacklisted(const struct ata_device dev, char modestr, const char *list[])
153	{
8bfa79fc	154	unsigned char model_num[ATA_ID_PROD_LEN + 1];
669a5db4 JG	155	int i = 0;
669a5db4 JG	156
8bfa79fc	157	ata_id_c_string(dev->id, model_num, ATA_ID_PROD, sizeof(model_num));
669a5db4	158
8bfa79fc TH	159	while (list[i] != NULL) {
8bfa79fc TH	160	if (!strcmp(list[i], model_num)) {
85cd7251	161	printk(KERN_WARNING DRV_NAME ": %s is not supported for %s.\n",
669a5db4 JG	162	modestr, list[i]);
	163	return 1;
	164	}
	165	i++;
	166	}
	167	return 0;
	168	}
	169
	170	/**
	171	* hpt366_filter - mode selection filter
669a5db4 JG	172	* @adev: ATA device
	173	*
	174	* Block UDMA on devices that cause trouble with this controller.
	175	*/
85cd7251	176
a76b62ca	177	static unsigned long hpt366_filter(struct ata_device *adev, unsigned long mask)
669a5db4 JG	178	{
	179	if (adev->class == ATA_DEV_ATA) {
	180	if (hpt_dma_blacklisted(adev, "UDMA", bad_ata33))
	181	mask &= ~ATA_MASK_UDMA;
	182	if (hpt_dma_blacklisted(adev, "UDMA3", bad_ata66_3))
6ddd6861	183	mask &= ~(0xF8 << ATA_SHIFT_UDMA);
669a5db4	184	if (hpt_dma_blacklisted(adev, "UDMA4", bad_ata66_4))
6ddd6861	185	mask &= ~(0xF0 << ATA_SHIFT_UDMA);
669a5db4	186	}
a76b62ca	187	return ata_pci_default_filter(adev, mask);
669a5db4 JG	188	}
	189
	190	/**
	191	* hpt36x_find_mode - reset the hpt36x bus
	192	* @ap: ATA port
	193	* @speed: transfer mode
	194	*
	195	* Return the 32bit register programming information for this channel
	196	* that matches the speed provided.
	197	*/
85cd7251	198
669a5db4 JG	199	static u32 hpt36x_find_mode(struct ata_port *ap, int speed)
	200	{
	201	struct hpt_clock *clocks = ap->host->private_data;
85cd7251	202
669a5db4 JG	203	while(clocks->xfer_speed) {
	204	if (clocks->xfer_speed == speed)
	205	return clocks->timing;
	206	clocks++;
	207	}
	208	BUG();
	209	return 0xffffffffU; /* silence compiler warning */
	210	}
85cd7251	211
fecfda5d AC	212	static int hpt36x_cable_detect(struct ata_port *ap)
	213	{
	214	u8 ata66;
	215	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	216
	217	pci_read_config_byte(pdev, 0x5A, &ata66);
	218	if (ata66 & (1 << ap->port_no))
	219	return ATA_CBL_PATA40;
	220	return ATA_CBL_PATA80;
	221	}
	222
669a5db4 JG	223	/**
	224	* hpt366_set_piomode - PIO setup
	225	* @ap: ATA interface
	226	* @adev: device on the interface
	227	*
85cd7251	228	* Perform PIO mode setup.
669a5db4	229	*/
85cd7251	230
669a5db4 JG	231	static void hpt366_set_piomode(struct ata_port ap, struct ata_device adev)
	232	{
	233	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	234	u32 addr1, addr2;
	235	u32 reg;
	236	u32 mode;
	237	u8 fast;
	238
	239	addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
	240	addr2 = 0x51 + 4 * ap->port_no;
85cd7251	241
669a5db4 JG	242	/* Fast interrupt prediction disable, hold off interrupt disable */
	243	pci_read_config_byte(pdev, addr2, &fast);
	244	if (fast & 0x80) {
	245	fast &= ~0x80;
	246	pci_write_config_byte(pdev, addr2, fast);
	247	}
85cd7251	248
669a5db4 JG	249	pci_read_config_dword(pdev, addr1, &reg);
	250	mode = hpt36x_find_mode(ap, adev->pio_mode);
	251	mode &= ~0x8000000; /* No FIFO in PIO */
	252	mode &= ~0x30070000; /* Leave config bits alone */
	253	reg &= 0x30070000; /* Strip timing bits */
	254	pci_write_config_dword(pdev, addr1, reg \| mode);
	255	}
	256
	257	/**
	258	* hpt366_set_dmamode - DMA timing setup
	259	* @ap: ATA interface
	260	* @adev: Device being configured
	261	*
	262	* Set up the channel for MWDMA or UDMA modes. Much the same as with
	263	* PIO, load the mode number and then set MWDMA or UDMA flag.
	264	*/
85cd7251	265
669a5db4 JG	266	static void hpt366_set_dmamode(struct ata_port ap, struct ata_device adev)
	267	{
	268	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	269	u32 addr1, addr2;
	270	u32 reg;
	271	u32 mode;
	272	u8 fast;
	273
	274	addr1 = 0x40 + 4 * (adev->devno + 2 * ap->port_no);
	275	addr2 = 0x51 + 4 * ap->port_no;
85cd7251	276
669a5db4 JG	277	/* Fast interrupt prediction disable, hold off interrupt disable */
	278	pci_read_config_byte(pdev, addr2, &fast);
	279	if (fast & 0x80) {
	280	fast &= ~0x80;
	281	pci_write_config_byte(pdev, addr2, fast);
	282	}
85cd7251	283
669a5db4 JG	284	pci_read_config_dword(pdev, addr1, &reg);
	285	mode = hpt36x_find_mode(ap, adev->dma_mode);
	286	mode \|= 0x8000000; /* FIFO in MWDMA or UDMA */
	287	mode &= ~0xC0000000; /* Leave config bits alone */
	288	reg &= 0xC0000000; /* Strip timing bits */
	289	pci_write_config_dword(pdev, addr1, reg \| mode);
	290	}
	291
	292	static struct scsi_host_template hpt36x_sht = {
68d1d07b	293	ATA_BMDMA_SHT(DRV_NAME),
669a5db4 JG	294	};
	295
	296	/*
	297	* Configuration for HPT366/68
	298	*/
85cd7251	299
669a5db4	300	static struct ata_port_operations hpt366_port_ops = {
669a5db4 JG	301	.set_piomode = hpt366_set_piomode,
	302	.set_dmamode = hpt366_set_dmamode,
	303	.mode_filter = hpt366_filter,
85cd7251	304
669a5db4 JG	305	.tf_load = ata_tf_load,
	306	.tf_read = ata_tf_read,
	307	.check_status = ata_check_status,
	308	.exec_command = ata_exec_command,
	309	.dev_select = ata_std_dev_select,
	310
	311	.freeze = ata_bmdma_freeze,
	312	.thaw = ata_bmdma_thaw,
4349eebf	313	.error_handler = ata_bmdma_error_handler,
669a5db4	314	.post_internal_cmd = ata_bmdma_post_internal_cmd,
fecfda5d	315	.cable_detect = hpt36x_cable_detect,
669a5db4 JG	316
	317	.bmdma_setup = ata_bmdma_setup,
	318	.bmdma_start = ata_bmdma_start,
	319	.bmdma_stop = ata_bmdma_stop,
	320	.bmdma_status = ata_bmdma_status,
	321
	322	.qc_prep = ata_qc_prep,
	323	.qc_issue = ata_qc_issue_prot,
bda30288	324
0d5ff566	325	.data_xfer = ata_data_xfer,
669a5db4 JG	326
	327	.irq_handler = ata_interrupt,
	328	.irq_clear = ata_bmdma_irq_clear,
246ce3b6	329	.irq_on = ata_irq_on,
669a5db4	330
81ad1837	331	.port_start = ata_sff_port_start,
85cd7251	332	};
669a5db4	333
aa54ab1e AC	334	/**
	335	* hpt36x_init_chipset - common chip setup
	336	* @dev: PCI device
	337	*
	338	* Perform the chip setup work that must be done at both init and
	339	* resume time
	340	*/
	341
	342	static void hpt36x_init_chipset(struct pci_dev *dev)
	343	{
	344	u8 drive_fast;
	345	pci_write_config_byte(dev, PCI_CACHE_LINE_SIZE, (L1_CACHE_BYTES / 4));
	346	pci_write_config_byte(dev, PCI_LATENCY_TIMER, 0x78);
	347	pci_write_config_byte(dev, PCI_MIN_GNT, 0x08);
	348	pci_write_config_byte(dev, PCI_MAX_LAT, 0x08);
	349
	350	pci_read_config_byte(dev, 0x51, &drive_fast);
	351	if (drive_fast & 0x80)
	352	pci_write_config_byte(dev, 0x51, drive_fast & ~0x80);
	353	}
	354
669a5db4 JG	355	/**
	356	* hpt36x_init_one - Initialise an HPT366/368
	357	* @dev: PCI device
	358	* @id: Entry in match table
	359	*
	360	* Initialise an HPT36x device. There are some interesting complications
	361	* here. Firstly the chip may report 366 and be one of several variants.
	362	* Secondly all the timings depend on the clock for the chip which we must
	363	* detect and look up
	364	*
	365	* This is the known chip mappings. It may be missing a couple of later
	366	* releases.
	367	*
	368	* Chip version PCI Rev Notes
	369	* HPT366 4 (HPT366) 0 UDMA66
	370	* HPT366 4 (HPT366) 1 UDMA66
	371	* HPT368 4 (HPT366) 2 UDMA66
	372	* HPT37x/30x 4 (HPT366) 3+ Other driver
	373	*
	374	*/
85cd7251	375
669a5db4 JG	376	static int hpt36x_init_one(struct pci_dev dev, const struct pci_device_id id)
669a5db4 JG	377	{
1626aeb8	378	static const struct ata_port_info info_hpt366 = {
669a5db4	379	.sht = &hpt36x_sht,
1d2808fd	380	.flags = ATA_FLAG_SLAVE_POSS,
669a5db4 JG	381	.pio_mask = 0x1f,
669a5db4 JG	382	.mwdma_mask = 0x07,
bf6263a8	383	.udma_mask = ATA_UDMA4,
669a5db4 JG	384	.port_ops = &hpt366_port_ops
669a5db4 JG	385	};
1626aeb8 TH	386	struct ata_port_info info = info_hpt366;
1626aeb8 TH	387	const struct ata_port_info *ppi[] = { &info, NULL };
669a5db4 JG	388
	389	u32 class_rev;
	390	u32 reg1;
f08048e9 TH	391	int rc;
	392
	393	rc = pcim_enable_device(dev);
	394	if (rc)
	395	return rc;
669a5db4 JG	396
	397	pci_read_config_dword(dev, PCI_CLASS_REVISION, &class_rev);
	398	class_rev &= 0xFF;
85cd7251	399
669a5db4 JG	400	/* May be a later chip in disguise. Check */
	401	/* Newer chips are not in the HPT36x driver. Ignore them */
	402	if (class_rev > 2)
	403	return -ENODEV;
	404
aa54ab1e	405	hpt36x_init_chipset(dev);
669a5db4 JG	406
669a5db4 JG	407	pci_read_config_dword(dev, 0x40, &reg1);
85cd7251	408
669a5db4 JG	409	/* PCI clocking determines the ATA timing values to use */
669a5db4 JG	410	/* info_hpt366 is safe against re-entry so we can scribble on it */
2c136efc	411	switch((reg1 & 0x700) >> 8) {
669a5db4	412	case 5:
1626aeb8	413	info.private_data = &hpt366_40;
669a5db4 JG	414	break;
669a5db4 JG	415	case 9:
1626aeb8	416	info.private_data = &hpt366_25;
669a5db4 JG	417	break;
669a5db4 JG	418	default:
1626aeb8	419	info.private_data = &hpt366_33;
669a5db4 JG	420	break;
	421	}
	422	/* Now kick off ATA set up */
1626aeb8	423	return ata_pci_init_one(dev, ppi);
669a5db4 JG	424	}
669a5db4 JG	425
438ac6d5	426	#ifdef CONFIG_PM
aa54ab1e AC	427	static int hpt36x_reinit_one(struct pci_dev *dev)
aa54ab1e AC	428	{
f08048e9 TH	429	struct ata_host *host = dev_get_drvdata(&dev->dev);
	430	int rc;
	431
	432	rc = ata_pci_device_do_resume(dev);
	433	if (rc)
	434	return rc;
aa54ab1e	435	hpt36x_init_chipset(dev);
f08048e9 TH	436	ata_host_resume(host);
f08048e9 TH	437	return 0;
aa54ab1e	438	}
438ac6d5	439	#endif
aa54ab1e	440
2d2744fc JG	441	static const struct pci_device_id hpt36x[] = {
2d2744fc JG	442	{ PCI_VDEVICE(TTI, PCI_DEVICE_ID_TTI_HPT366), },
2d2744fc	443	{ },
669a5db4 JG	444	};
	445
	446	static struct pci_driver hpt36x_pci_driver = {
2d2744fc	447	.name = DRV_NAME,
669a5db4 JG	448	.id_table = hpt36x,
669a5db4 JG	449	.probe = hpt36x_init_one,
aa54ab1e	450	.remove = ata_pci_remove_one,
438ac6d5	451	#ifdef CONFIG_PM
aa54ab1e AC	452	.suspend = ata_pci_device_suspend,
aa54ab1e AC	453	.resume = hpt36x_reinit_one,
438ac6d5	454	#endif
669a5db4 JG	455	};
	456
	457	static int __init hpt36x_init(void)
	458	{
	459	return pci_register_driver(&hpt36x_pci_driver);
	460	}
	461
669a5db4 JG	462	static void __exit hpt36x_exit(void)
	463	{
	464	pci_unregister_driver(&hpt36x_pci_driver);
	465	}
	466
669a5db4 JG	467	MODULE_AUTHOR("Alan Cox");
	468	MODULE_DESCRIPTION("low-level driver for the Highpoint HPT366/368");
	469	MODULE_LICENSE("GPL");
	470	MODULE_DEVICE_TABLE(pci, hpt36x);
	471	MODULE_VERSION(DRV_VERSION);
	472
	473	module_init(hpt36x_init);
	474	module_exit(hpt36x_exit);