]>
Commit | Line | Data |
---|---|---|
873960c8 SR |
1 | /* |
2 | * drivers/mtd/nand/pxa3xx_nand.c | |
3 | * | |
4 | * Copyright © 2005 Intel Corporation | |
5 | * Copyright © 2006 Marvell International Ltd. | |
6 | * | |
7 | * SPDX-License-Identifier: GPL-2.0 | |
8 | */ | |
9 | ||
10 | #include <common.h> | |
11 | #include <malloc.h> | |
12 | #include <nand.h> | |
1221ce45 | 13 | #include <linux/errno.h> |
873960c8 SR |
14 | #include <asm/io.h> |
15 | #include <asm/arch/cpu.h> | |
16 | #include <linux/mtd/mtd.h> | |
17 | #include <linux/mtd/nand.h> | |
18 | #include <linux/types.h> | |
19 | ||
20 | #include "pxa3xx_nand.h" | |
21 | ||
873960c8 SR |
22 | #define TIMEOUT_DRAIN_FIFO 5 /* in ms */ |
23 | #define CHIP_DELAY_TIMEOUT 200 | |
24 | #define NAND_STOP_DELAY 40 | |
25 | #define PAGE_CHUNK_SIZE (2048) | |
26 | ||
27 | /* | |
28 | * Define a buffer size for the initial command that detects the flash device: | |
29 | * STATUS, READID and PARAM. The largest of these is the PARAM command, | |
30 | * needing 256 bytes. | |
31 | */ | |
32 | #define INIT_BUFFER_SIZE 256 | |
33 | ||
34 | /* registers and bit definitions */ | |
35 | #define NDCR (0x00) /* Control register */ | |
36 | #define NDTR0CS0 (0x04) /* Timing Parameter 0 for CS0 */ | |
37 | #define NDTR1CS0 (0x0C) /* Timing Parameter 1 for CS0 */ | |
38 | #define NDSR (0x14) /* Status Register */ | |
39 | #define NDPCR (0x18) /* Page Count Register */ | |
40 | #define NDBDR0 (0x1C) /* Bad Block Register 0 */ | |
41 | #define NDBDR1 (0x20) /* Bad Block Register 1 */ | |
42 | #define NDECCCTRL (0x28) /* ECC control */ | |
43 | #define NDDB (0x40) /* Data Buffer */ | |
44 | #define NDCB0 (0x48) /* Command Buffer0 */ | |
45 | #define NDCB1 (0x4C) /* Command Buffer1 */ | |
46 | #define NDCB2 (0x50) /* Command Buffer2 */ | |
47 | ||
48 | #define NDCR_SPARE_EN (0x1 << 31) | |
49 | #define NDCR_ECC_EN (0x1 << 30) | |
50 | #define NDCR_DMA_EN (0x1 << 29) | |
51 | #define NDCR_ND_RUN (0x1 << 28) | |
52 | #define NDCR_DWIDTH_C (0x1 << 27) | |
53 | #define NDCR_DWIDTH_M (0x1 << 26) | |
54 | #define NDCR_PAGE_SZ (0x1 << 24) | |
55 | #define NDCR_NCSX (0x1 << 23) | |
56 | #define NDCR_ND_MODE (0x3 << 21) | |
57 | #define NDCR_NAND_MODE (0x0) | |
58 | #define NDCR_CLR_PG_CNT (0x1 << 20) | |
59 | #define NDCR_STOP_ON_UNCOR (0x1 << 19) | |
60 | #define NDCR_RD_ID_CNT_MASK (0x7 << 16) | |
61 | #define NDCR_RD_ID_CNT(x) (((x) << 16) & NDCR_RD_ID_CNT_MASK) | |
62 | ||
63 | #define NDCR_RA_START (0x1 << 15) | |
64 | #define NDCR_PG_PER_BLK (0x1 << 14) | |
65 | #define NDCR_ND_ARB_EN (0x1 << 12) | |
66 | #define NDCR_INT_MASK (0xFFF) | |
67 | ||
68 | #define NDSR_MASK (0xfff) | |
69 | #define NDSR_ERR_CNT_OFF (16) | |
70 | #define NDSR_ERR_CNT_MASK (0x1f) | |
71 | #define NDSR_ERR_CNT(sr) ((sr >> NDSR_ERR_CNT_OFF) & NDSR_ERR_CNT_MASK) | |
72 | #define NDSR_RDY (0x1 << 12) | |
73 | #define NDSR_FLASH_RDY (0x1 << 11) | |
74 | #define NDSR_CS0_PAGED (0x1 << 10) | |
75 | #define NDSR_CS1_PAGED (0x1 << 9) | |
76 | #define NDSR_CS0_CMDD (0x1 << 8) | |
77 | #define NDSR_CS1_CMDD (0x1 << 7) | |
78 | #define NDSR_CS0_BBD (0x1 << 6) | |
79 | #define NDSR_CS1_BBD (0x1 << 5) | |
80 | #define NDSR_UNCORERR (0x1 << 4) | |
81 | #define NDSR_CORERR (0x1 << 3) | |
82 | #define NDSR_WRDREQ (0x1 << 2) | |
83 | #define NDSR_RDDREQ (0x1 << 1) | |
84 | #define NDSR_WRCMDREQ (0x1) | |
85 | ||
86 | #define NDCB0_LEN_OVRD (0x1 << 28) | |
87 | #define NDCB0_ST_ROW_EN (0x1 << 26) | |
88 | #define NDCB0_AUTO_RS (0x1 << 25) | |
89 | #define NDCB0_CSEL (0x1 << 24) | |
90 | #define NDCB0_EXT_CMD_TYPE_MASK (0x7 << 29) | |
91 | #define NDCB0_EXT_CMD_TYPE(x) (((x) << 29) & NDCB0_EXT_CMD_TYPE_MASK) | |
92 | #define NDCB0_CMD_TYPE_MASK (0x7 << 21) | |
93 | #define NDCB0_CMD_TYPE(x) (((x) << 21) & NDCB0_CMD_TYPE_MASK) | |
94 | #define NDCB0_NC (0x1 << 20) | |
95 | #define NDCB0_DBC (0x1 << 19) | |
96 | #define NDCB0_ADDR_CYC_MASK (0x7 << 16) | |
97 | #define NDCB0_ADDR_CYC(x) (((x) << 16) & NDCB0_ADDR_CYC_MASK) | |
98 | #define NDCB0_CMD2_MASK (0xff << 8) | |
99 | #define NDCB0_CMD1_MASK (0xff) | |
100 | #define NDCB0_ADDR_CYC_SHIFT (16) | |
101 | ||
102 | #define EXT_CMD_TYPE_DISPATCH 6 /* Command dispatch */ | |
103 | #define EXT_CMD_TYPE_NAKED_RW 5 /* Naked read or Naked write */ | |
104 | #define EXT_CMD_TYPE_READ 4 /* Read */ | |
105 | #define EXT_CMD_TYPE_DISP_WR 4 /* Command dispatch with write */ | |
106 | #define EXT_CMD_TYPE_FINAL 3 /* Final command */ | |
107 | #define EXT_CMD_TYPE_LAST_RW 1 /* Last naked read/write */ | |
108 | #define EXT_CMD_TYPE_MONO 0 /* Monolithic read/write */ | |
109 | ||
110 | /* macros for registers read/write */ | |
111 | #define nand_writel(info, off, val) \ | |
112 | writel((val), (info)->mmio_base + (off)) | |
113 | ||
114 | #define nand_readl(info, off) \ | |
115 | readl((info)->mmio_base + (off)) | |
116 | ||
117 | /* error code and state */ | |
118 | enum { | |
119 | ERR_NONE = 0, | |
120 | ERR_DMABUSERR = -1, | |
121 | ERR_SENDCMD = -2, | |
122 | ERR_UNCORERR = -3, | |
123 | ERR_BBERR = -4, | |
124 | ERR_CORERR = -5, | |
125 | }; | |
126 | ||
127 | enum { | |
128 | STATE_IDLE = 0, | |
129 | STATE_PREPARED, | |
130 | STATE_CMD_HANDLE, | |
131 | STATE_DMA_READING, | |
132 | STATE_DMA_WRITING, | |
133 | STATE_DMA_DONE, | |
134 | STATE_PIO_READING, | |
135 | STATE_PIO_WRITING, | |
136 | STATE_CMD_DONE, | |
137 | STATE_READY, | |
138 | }; | |
139 | ||
140 | enum pxa3xx_nand_variant { | |
141 | PXA3XX_NAND_VARIANT_PXA, | |
142 | PXA3XX_NAND_VARIANT_ARMADA370, | |
143 | }; | |
144 | ||
145 | struct pxa3xx_nand_host { | |
146 | struct nand_chip chip; | |
147 | struct mtd_info *mtd; | |
148 | void *info_data; | |
149 | ||
150 | /* page size of attached chip */ | |
151 | int use_ecc; | |
152 | int cs; | |
153 | ||
154 | /* calculated from pxa3xx_nand_flash data */ | |
155 | unsigned int col_addr_cycles; | |
156 | unsigned int row_addr_cycles; | |
157 | size_t read_id_bytes; | |
158 | ||
159 | }; | |
160 | ||
161 | struct pxa3xx_nand_info { | |
162 | struct nand_hw_control controller; | |
163 | struct pxa3xx_nand_platform_data *pdata; | |
164 | ||
165 | struct clk *clk; | |
166 | void __iomem *mmio_base; | |
167 | unsigned long mmio_phys; | |
168 | int cmd_complete, dev_ready; | |
169 | ||
170 | unsigned int buf_start; | |
171 | unsigned int buf_count; | |
172 | unsigned int buf_size; | |
173 | unsigned int data_buff_pos; | |
174 | unsigned int oob_buff_pos; | |
175 | ||
176 | unsigned char *data_buff; | |
177 | unsigned char *oob_buff; | |
178 | ||
179 | struct pxa3xx_nand_host *host[NUM_CHIP_SELECT]; | |
180 | unsigned int state; | |
181 | ||
182 | /* | |
183 | * This driver supports NFCv1 (as found in PXA SoC) | |
184 | * and NFCv2 (as found in Armada 370/XP SoC). | |
185 | */ | |
186 | enum pxa3xx_nand_variant variant; | |
187 | ||
188 | int cs; | |
189 | int use_ecc; /* use HW ECC ? */ | |
190 | int ecc_bch; /* using BCH ECC? */ | |
191 | int use_spare; /* use spare ? */ | |
192 | int need_wait; | |
193 | ||
194 | unsigned int data_size; /* data to be read from FIFO */ | |
195 | unsigned int chunk_size; /* split commands chunk size */ | |
196 | unsigned int oob_size; | |
197 | unsigned int spare_size; | |
198 | unsigned int ecc_size; | |
199 | unsigned int ecc_err_cnt; | |
200 | unsigned int max_bitflips; | |
201 | int retcode; | |
202 | ||
203 | /* cached register value */ | |
204 | uint32_t reg_ndcr; | |
205 | uint32_t ndtr0cs0; | |
206 | uint32_t ndtr1cs0; | |
207 | ||
208 | /* generated NDCBx register values */ | |
209 | uint32_t ndcb0; | |
210 | uint32_t ndcb1; | |
211 | uint32_t ndcb2; | |
212 | uint32_t ndcb3; | |
213 | }; | |
214 | ||
215 | static struct pxa3xx_nand_timing timing[] = { | |
216 | { 40, 80, 60, 100, 80, 100, 90000, 400, 40, }, | |
217 | { 10, 0, 20, 40, 30, 40, 11123, 110, 10, }, | |
218 | { 10, 25, 15, 25, 15, 30, 25000, 60, 10, }, | |
219 | { 10, 35, 15, 25, 15, 25, 25000, 60, 10, }, | |
220 | }; | |
221 | ||
222 | static struct pxa3xx_nand_flash builtin_flash_types[] = { | |
223 | { 0x46ec, 16, 16, &timing[1] }, | |
224 | { 0xdaec, 8, 8, &timing[1] }, | |
225 | { 0xd7ec, 8, 8, &timing[1] }, | |
226 | { 0xa12c, 8, 8, &timing[2] }, | |
227 | { 0xb12c, 16, 16, &timing[2] }, | |
228 | { 0xdc2c, 8, 8, &timing[2] }, | |
229 | { 0xcc2c, 16, 16, &timing[2] }, | |
230 | { 0xba20, 16, 16, &timing[3] }, | |
231 | }; | |
232 | ||
233 | static u8 bbt_pattern[] = {'M', 'V', 'B', 'b', 't', '0' }; | |
234 | static u8 bbt_mirror_pattern[] = {'1', 't', 'b', 'B', 'V', 'M' }; | |
235 | ||
236 | static struct nand_bbt_descr bbt_main_descr = { | |
237 | .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE | |
238 | | NAND_BBT_2BIT | NAND_BBT_VERSION, | |
239 | .offs = 8, | |
240 | .len = 6, | |
241 | .veroffs = 14, | |
242 | .maxblocks = 8, /* Last 8 blocks in each chip */ | |
243 | .pattern = bbt_pattern | |
244 | }; | |
245 | ||
246 | static struct nand_bbt_descr bbt_mirror_descr = { | |
247 | .options = NAND_BBT_LASTBLOCK | NAND_BBT_CREATE | NAND_BBT_WRITE | |
248 | | NAND_BBT_2BIT | NAND_BBT_VERSION, | |
249 | .offs = 8, | |
250 | .len = 6, | |
251 | .veroffs = 14, | |
252 | .maxblocks = 8, /* Last 8 blocks in each chip */ | |
253 | .pattern = bbt_mirror_pattern | |
254 | }; | |
255 | ||
256 | static struct nand_ecclayout ecc_layout_2KB_bch4bit = { | |
257 | .eccbytes = 32, | |
258 | .eccpos = { | |
259 | 32, 33, 34, 35, 36, 37, 38, 39, | |
260 | 40, 41, 42, 43, 44, 45, 46, 47, | |
261 | 48, 49, 50, 51, 52, 53, 54, 55, | |
262 | 56, 57, 58, 59, 60, 61, 62, 63}, | |
263 | .oobfree = { {2, 30} } | |
264 | }; | |
265 | ||
266 | static struct nand_ecclayout ecc_layout_4KB_bch4bit = { | |
267 | .eccbytes = 64, | |
268 | .eccpos = { | |
269 | 32, 33, 34, 35, 36, 37, 38, 39, | |
270 | 40, 41, 42, 43, 44, 45, 46, 47, | |
271 | 48, 49, 50, 51, 52, 53, 54, 55, | |
272 | 56, 57, 58, 59, 60, 61, 62, 63, | |
273 | 96, 97, 98, 99, 100, 101, 102, 103, | |
274 | 104, 105, 106, 107, 108, 109, 110, 111, | |
275 | 112, 113, 114, 115, 116, 117, 118, 119, | |
276 | 120, 121, 122, 123, 124, 125, 126, 127}, | |
277 | /* Bootrom looks in bytes 0 & 5 for bad blocks */ | |
278 | .oobfree = { {6, 26}, { 64, 32} } | |
279 | }; | |
280 | ||
281 | static struct nand_ecclayout ecc_layout_4KB_bch8bit = { | |
282 | .eccbytes = 128, | |
283 | .eccpos = { | |
284 | 32, 33, 34, 35, 36, 37, 38, 39, | |
285 | 40, 41, 42, 43, 44, 45, 46, 47, | |
286 | 48, 49, 50, 51, 52, 53, 54, 55, | |
287 | 56, 57, 58, 59, 60, 61, 62, 63}, | |
288 | .oobfree = { } | |
289 | }; | |
290 | ||
291 | #define NDTR0_tCH(c) (min((c), 7) << 19) | |
292 | #define NDTR0_tCS(c) (min((c), 7) << 16) | |
293 | #define NDTR0_tWH(c) (min((c), 7) << 11) | |
294 | #define NDTR0_tWP(c) (min((c), 7) << 8) | |
295 | #define NDTR0_tRH(c) (min((c), 7) << 3) | |
296 | #define NDTR0_tRP(c) (min((c), 7) << 0) | |
297 | ||
298 | #define NDTR1_tR(c) (min((c), 65535) << 16) | |
299 | #define NDTR1_tWHR(c) (min((c), 15) << 4) | |
300 | #define NDTR1_tAR(c) (min((c), 15) << 0) | |
301 | ||
302 | /* convert nano-seconds to nand flash controller clock cycles */ | |
303 | #define ns2cycle(ns, clk) (int)((ns) * (clk / 1000000) / 1000) | |
304 | ||
305 | static enum pxa3xx_nand_variant pxa3xx_nand_get_variant(void) | |
306 | { | |
307 | /* We only support the Armada 370/XP/38x for now */ | |
308 | return PXA3XX_NAND_VARIANT_ARMADA370; | |
309 | } | |
310 | ||
311 | static void pxa3xx_nand_set_timing(struct pxa3xx_nand_host *host, | |
312 | const struct pxa3xx_nand_timing *t) | |
313 | { | |
314 | struct pxa3xx_nand_info *info = host->info_data; | |
315 | unsigned long nand_clk = mvebu_get_nand_clock(); | |
316 | uint32_t ndtr0, ndtr1; | |
317 | ||
318 | ndtr0 = NDTR0_tCH(ns2cycle(t->tCH, nand_clk)) | | |
319 | NDTR0_tCS(ns2cycle(t->tCS, nand_clk)) | | |
320 | NDTR0_tWH(ns2cycle(t->tWH, nand_clk)) | | |
321 | NDTR0_tWP(ns2cycle(t->tWP, nand_clk)) | | |
322 | NDTR0_tRH(ns2cycle(t->tRH, nand_clk)) | | |
323 | NDTR0_tRP(ns2cycle(t->tRP, nand_clk)); | |
324 | ||
325 | ndtr1 = NDTR1_tR(ns2cycle(t->tR, nand_clk)) | | |
326 | NDTR1_tWHR(ns2cycle(t->tWHR, nand_clk)) | | |
327 | NDTR1_tAR(ns2cycle(t->tAR, nand_clk)); | |
328 | ||
329 | info->ndtr0cs0 = ndtr0; | |
330 | info->ndtr1cs0 = ndtr1; | |
331 | nand_writel(info, NDTR0CS0, ndtr0); | |
332 | nand_writel(info, NDTR1CS0, ndtr1); | |
333 | } | |
334 | ||
335 | static void pxa3xx_nand_set_sdr_timing(struct pxa3xx_nand_host *host, | |
336 | const struct nand_sdr_timings *t) | |
337 | { | |
338 | struct pxa3xx_nand_info *info = host->info_data; | |
339 | struct nand_chip *chip = &host->chip; | |
340 | unsigned long nand_clk = mvebu_get_nand_clock(); | |
341 | uint32_t ndtr0, ndtr1; | |
342 | ||
343 | u32 tCH_min = DIV_ROUND_UP(t->tCH_min, 1000); | |
344 | u32 tCS_min = DIV_ROUND_UP(t->tCS_min, 1000); | |
345 | u32 tWH_min = DIV_ROUND_UP(t->tWH_min, 1000); | |
346 | u32 tWP_min = DIV_ROUND_UP(t->tWC_min - tWH_min, 1000); | |
347 | u32 tREH_min = DIV_ROUND_UP(t->tREH_min, 1000); | |
348 | u32 tRP_min = DIV_ROUND_UP(t->tRC_min - tREH_min, 1000); | |
349 | u32 tR = chip->chip_delay * 1000; | |
350 | u32 tWHR_min = DIV_ROUND_UP(t->tWHR_min, 1000); | |
351 | u32 tAR_min = DIV_ROUND_UP(t->tAR_min, 1000); | |
352 | ||
353 | /* fallback to a default value if tR = 0 */ | |
354 | if (!tR) | |
355 | tR = 20000; | |
356 | ||
357 | ndtr0 = NDTR0_tCH(ns2cycle(tCH_min, nand_clk)) | | |
358 | NDTR0_tCS(ns2cycle(tCS_min, nand_clk)) | | |
359 | NDTR0_tWH(ns2cycle(tWH_min, nand_clk)) | | |
360 | NDTR0_tWP(ns2cycle(tWP_min, nand_clk)) | | |
361 | NDTR0_tRH(ns2cycle(tREH_min, nand_clk)) | | |
362 | NDTR0_tRP(ns2cycle(tRP_min, nand_clk)); | |
363 | ||
364 | ndtr1 = NDTR1_tR(ns2cycle(tR, nand_clk)) | | |
365 | NDTR1_tWHR(ns2cycle(tWHR_min, nand_clk)) | | |
366 | NDTR1_tAR(ns2cycle(tAR_min, nand_clk)); | |
367 | ||
368 | info->ndtr0cs0 = ndtr0; | |
369 | info->ndtr1cs0 = ndtr1; | |
370 | nand_writel(info, NDTR0CS0, ndtr0); | |
371 | nand_writel(info, NDTR1CS0, ndtr1); | |
372 | } | |
373 | ||
374 | static int pxa3xx_nand_init_timings(struct pxa3xx_nand_host *host) | |
375 | { | |
376 | const struct nand_sdr_timings *timings; | |
377 | struct nand_chip *chip = &host->chip; | |
378 | struct pxa3xx_nand_info *info = host->info_data; | |
379 | const struct pxa3xx_nand_flash *f = NULL; | |
380 | int mode, id, ntypes, i; | |
381 | ||
382 | mode = onfi_get_async_timing_mode(chip); | |
383 | if (mode == ONFI_TIMING_MODE_UNKNOWN) { | |
384 | ntypes = ARRAY_SIZE(builtin_flash_types); | |
385 | ||
386 | chip->cmdfunc(host->mtd, NAND_CMD_READID, 0x00, -1); | |
387 | ||
388 | id = chip->read_byte(host->mtd); | |
389 | id |= chip->read_byte(host->mtd) << 0x8; | |
390 | ||
391 | for (i = 0; i < ntypes; i++) { | |
392 | f = &builtin_flash_types[i]; | |
393 | ||
394 | if (f->chip_id == id) | |
395 | break; | |
396 | } | |
397 | ||
398 | if (i == ntypes) { | |
399 | dev_err(&info->pdev->dev, "Error: timings not found\n"); | |
400 | return -EINVAL; | |
401 | } | |
402 | ||
403 | pxa3xx_nand_set_timing(host, f->timing); | |
404 | ||
405 | if (f->flash_width == 16) { | |
406 | info->reg_ndcr |= NDCR_DWIDTH_M; | |
407 | chip->options |= NAND_BUSWIDTH_16; | |
408 | } | |
409 | ||
410 | info->reg_ndcr |= (f->dfc_width == 16) ? NDCR_DWIDTH_C : 0; | |
411 | } else { | |
412 | mode = fls(mode) - 1; | |
413 | if (mode < 0) | |
414 | mode = 0; | |
415 | ||
416 | timings = onfi_async_timing_mode_to_sdr_timings(mode); | |
417 | if (IS_ERR(timings)) | |
418 | return PTR_ERR(timings); | |
419 | ||
420 | pxa3xx_nand_set_sdr_timing(host, timings); | |
421 | } | |
422 | ||
423 | return 0; | |
424 | } | |
425 | ||
426 | /* | |
427 | * Set the data and OOB size, depending on the selected | |
428 | * spare and ECC configuration. | |
429 | * Only applicable to READ0, READOOB and PAGEPROG commands. | |
430 | */ | |
431 | static void pxa3xx_set_datasize(struct pxa3xx_nand_info *info, | |
432 | struct mtd_info *mtd) | |
433 | { | |
434 | int oob_enable = info->reg_ndcr & NDCR_SPARE_EN; | |
435 | ||
436 | info->data_size = mtd->writesize; | |
437 | if (!oob_enable) | |
438 | return; | |
439 | ||
440 | info->oob_size = info->spare_size; | |
441 | if (!info->use_ecc) | |
442 | info->oob_size += info->ecc_size; | |
443 | } | |
444 | ||
445 | /** | |
1b25e586 | 446 | * NOTE: it is a must to set ND_RUN first, then write |
873960c8 SR |
447 | * command buffer, otherwise, it does not work. |
448 | * We enable all the interrupt at the same time, and | |
449 | * let pxa3xx_nand_irq to handle all logic. | |
450 | */ | |
451 | static void pxa3xx_nand_start(struct pxa3xx_nand_info *info) | |
452 | { | |
453 | uint32_t ndcr; | |
454 | ||
455 | ndcr = info->reg_ndcr; | |
456 | ||
457 | if (info->use_ecc) { | |
458 | ndcr |= NDCR_ECC_EN; | |
459 | if (info->ecc_bch) | |
460 | nand_writel(info, NDECCCTRL, 0x1); | |
461 | } else { | |
462 | ndcr &= ~NDCR_ECC_EN; | |
463 | if (info->ecc_bch) | |
464 | nand_writel(info, NDECCCTRL, 0x0); | |
465 | } | |
466 | ||
467 | ndcr &= ~NDCR_DMA_EN; | |
468 | ||
469 | if (info->use_spare) | |
470 | ndcr |= NDCR_SPARE_EN; | |
471 | else | |
472 | ndcr &= ~NDCR_SPARE_EN; | |
473 | ||
474 | ndcr |= NDCR_ND_RUN; | |
475 | ||
476 | /* clear status bits and run */ | |
477 | nand_writel(info, NDCR, 0); | |
478 | nand_writel(info, NDSR, NDSR_MASK); | |
479 | nand_writel(info, NDCR, ndcr); | |
480 | } | |
481 | ||
482 | static void disable_int(struct pxa3xx_nand_info *info, uint32_t int_mask) | |
483 | { | |
484 | uint32_t ndcr; | |
485 | ||
486 | ndcr = nand_readl(info, NDCR); | |
487 | nand_writel(info, NDCR, ndcr | int_mask); | |
488 | } | |
489 | ||
490 | static void drain_fifo(struct pxa3xx_nand_info *info, void *data, int len) | |
491 | { | |
492 | if (info->ecc_bch) { | |
493 | u32 ts; | |
494 | ||
495 | /* | |
496 | * According to the datasheet, when reading from NDDB | |
497 | * with BCH enabled, after each 32 bytes reads, we | |
498 | * have to make sure that the NDSR.RDDREQ bit is set. | |
499 | * | |
500 | * Drain the FIFO 8 32 bits reads at a time, and skip | |
501 | * the polling on the last read. | |
502 | */ | |
503 | while (len > 8) { | |
504 | readsl(info->mmio_base + NDDB, data, 8); | |
505 | ||
506 | ts = get_timer(0); | |
507 | while (!(nand_readl(info, NDSR) & NDSR_RDDREQ)) { | |
508 | if (get_timer(ts) > TIMEOUT_DRAIN_FIFO) { | |
509 | dev_err(&info->pdev->dev, | |
510 | "Timeout on RDDREQ while draining the FIFO\n"); | |
511 | return; | |
512 | } | |
513 | } | |
514 | ||
515 | data += 32; | |
516 | len -= 8; | |
517 | } | |
518 | } | |
519 | ||
520 | readsl(info->mmio_base + NDDB, data, len); | |
521 | } | |
522 | ||
523 | static void handle_data_pio(struct pxa3xx_nand_info *info) | |
524 | { | |
525 | unsigned int do_bytes = min(info->data_size, info->chunk_size); | |
526 | ||
527 | switch (info->state) { | |
528 | case STATE_PIO_WRITING: | |
529 | writesl(info->mmio_base + NDDB, | |
530 | info->data_buff + info->data_buff_pos, | |
531 | DIV_ROUND_UP(do_bytes, 4)); | |
532 | ||
533 | if (info->oob_size > 0) | |
534 | writesl(info->mmio_base + NDDB, | |
535 | info->oob_buff + info->oob_buff_pos, | |
536 | DIV_ROUND_UP(info->oob_size, 4)); | |
537 | break; | |
538 | case STATE_PIO_READING: | |
539 | drain_fifo(info, | |
540 | info->data_buff + info->data_buff_pos, | |
541 | DIV_ROUND_UP(do_bytes, 4)); | |
542 | ||
543 | if (info->oob_size > 0) | |
544 | drain_fifo(info, | |
545 | info->oob_buff + info->oob_buff_pos, | |
546 | DIV_ROUND_UP(info->oob_size, 4)); | |
547 | break; | |
548 | default: | |
549 | dev_err(&info->pdev->dev, "%s: invalid state %d\n", __func__, | |
550 | info->state); | |
551 | BUG(); | |
552 | } | |
553 | ||
554 | /* Update buffer pointers for multi-page read/write */ | |
555 | info->data_buff_pos += do_bytes; | |
556 | info->oob_buff_pos += info->oob_size; | |
557 | info->data_size -= do_bytes; | |
558 | } | |
559 | ||
560 | static void pxa3xx_nand_irq_thread(struct pxa3xx_nand_info *info) | |
561 | { | |
562 | handle_data_pio(info); | |
563 | ||
564 | info->state = STATE_CMD_DONE; | |
565 | nand_writel(info, NDSR, NDSR_WRDREQ | NDSR_RDDREQ); | |
566 | } | |
567 | ||
568 | static irqreturn_t pxa3xx_nand_irq(struct pxa3xx_nand_info *info) | |
569 | { | |
570 | unsigned int status, is_completed = 0, is_ready = 0; | |
571 | unsigned int ready, cmd_done; | |
572 | irqreturn_t ret = IRQ_HANDLED; | |
573 | ||
574 | if (info->cs == 0) { | |
575 | ready = NDSR_FLASH_RDY; | |
576 | cmd_done = NDSR_CS0_CMDD; | |
577 | } else { | |
578 | ready = NDSR_RDY; | |
579 | cmd_done = NDSR_CS1_CMDD; | |
580 | } | |
581 | ||
582 | status = nand_readl(info, NDSR); | |
583 | ||
584 | if (status & NDSR_UNCORERR) | |
585 | info->retcode = ERR_UNCORERR; | |
586 | if (status & NDSR_CORERR) { | |
587 | info->retcode = ERR_CORERR; | |
588 | if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370 && | |
589 | info->ecc_bch) | |
590 | info->ecc_err_cnt = NDSR_ERR_CNT(status); | |
591 | else | |
592 | info->ecc_err_cnt = 1; | |
593 | ||
594 | /* | |
595 | * Each chunk composing a page is corrected independently, | |
596 | * and we need to store maximum number of corrected bitflips | |
597 | * to return it to the MTD layer in ecc.read_page(). | |
598 | */ | |
599 | info->max_bitflips = max_t(unsigned int, | |
600 | info->max_bitflips, | |
601 | info->ecc_err_cnt); | |
602 | } | |
603 | if (status & (NDSR_RDDREQ | NDSR_WRDREQ)) { | |
604 | info->state = (status & NDSR_RDDREQ) ? | |
605 | STATE_PIO_READING : STATE_PIO_WRITING; | |
606 | /* Call the IRQ thread in U-Boot directly */ | |
607 | pxa3xx_nand_irq_thread(info); | |
608 | return 0; | |
609 | } | |
610 | if (status & cmd_done) { | |
611 | info->state = STATE_CMD_DONE; | |
612 | is_completed = 1; | |
613 | } | |
614 | if (status & ready) { | |
615 | info->state = STATE_READY; | |
616 | is_ready = 1; | |
617 | } | |
618 | ||
619 | if (status & NDSR_WRCMDREQ) { | |
620 | nand_writel(info, NDSR, NDSR_WRCMDREQ); | |
621 | status &= ~NDSR_WRCMDREQ; | |
622 | info->state = STATE_CMD_HANDLE; | |
623 | ||
624 | /* | |
625 | * Command buffer registers NDCB{0-2} (and optionally NDCB3) | |
626 | * must be loaded by writing directly either 12 or 16 | |
627 | * bytes directly to NDCB0, four bytes at a time. | |
628 | * | |
629 | * Direct write access to NDCB1, NDCB2 and NDCB3 is ignored | |
630 | * but each NDCBx register can be read. | |
631 | */ | |
632 | nand_writel(info, NDCB0, info->ndcb0); | |
633 | nand_writel(info, NDCB0, info->ndcb1); | |
634 | nand_writel(info, NDCB0, info->ndcb2); | |
635 | ||
636 | /* NDCB3 register is available in NFCv2 (Armada 370/XP SoC) */ | |
637 | if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370) | |
638 | nand_writel(info, NDCB0, info->ndcb3); | |
639 | } | |
640 | ||
641 | /* clear NDSR to let the controller exit the IRQ */ | |
642 | nand_writel(info, NDSR, status); | |
643 | if (is_completed) | |
644 | info->cmd_complete = 1; | |
645 | if (is_ready) | |
646 | info->dev_ready = 1; | |
647 | ||
648 | return ret; | |
649 | } | |
650 | ||
651 | static inline int is_buf_blank(uint8_t *buf, size_t len) | |
652 | { | |
653 | for (; len > 0; len--) | |
654 | if (*buf++ != 0xff) | |
655 | return 0; | |
656 | return 1; | |
657 | } | |
658 | ||
659 | static void set_command_address(struct pxa3xx_nand_info *info, | |
660 | unsigned int page_size, uint16_t column, int page_addr) | |
661 | { | |
662 | /* small page addr setting */ | |
663 | if (page_size < PAGE_CHUNK_SIZE) { | |
664 | info->ndcb1 = ((page_addr & 0xFFFFFF) << 8) | |
665 | | (column & 0xFF); | |
666 | ||
667 | info->ndcb2 = 0; | |
668 | } else { | |
669 | info->ndcb1 = ((page_addr & 0xFFFF) << 16) | |
670 | | (column & 0xFFFF); | |
671 | ||
672 | if (page_addr & 0xFF0000) | |
673 | info->ndcb2 = (page_addr & 0xFF0000) >> 16; | |
674 | else | |
675 | info->ndcb2 = 0; | |
676 | } | |
677 | } | |
678 | ||
679 | static void prepare_start_command(struct pxa3xx_nand_info *info, int command) | |
680 | { | |
681 | struct pxa3xx_nand_host *host = info->host[info->cs]; | |
682 | struct mtd_info *mtd = host->mtd; | |
683 | ||
684 | /* reset data and oob column point to handle data */ | |
685 | info->buf_start = 0; | |
686 | info->buf_count = 0; | |
687 | info->oob_size = 0; | |
688 | info->data_buff_pos = 0; | |
689 | info->oob_buff_pos = 0; | |
690 | info->use_ecc = 0; | |
691 | info->use_spare = 1; | |
692 | info->retcode = ERR_NONE; | |
693 | info->ecc_err_cnt = 0; | |
694 | info->ndcb3 = 0; | |
695 | info->need_wait = 0; | |
696 | ||
697 | switch (command) { | |
698 | case NAND_CMD_READ0: | |
699 | case NAND_CMD_PAGEPROG: | |
700 | info->use_ecc = 1; | |
701 | case NAND_CMD_READOOB: | |
702 | pxa3xx_set_datasize(info, mtd); | |
703 | break; | |
704 | case NAND_CMD_PARAM: | |
705 | info->use_spare = 0; | |
706 | break; | |
707 | default: | |
708 | info->ndcb1 = 0; | |
709 | info->ndcb2 = 0; | |
710 | break; | |
711 | } | |
712 | ||
713 | /* | |
714 | * If we are about to issue a read command, or about to set | |
715 | * the write address, then clean the data buffer. | |
716 | */ | |
717 | if (command == NAND_CMD_READ0 || | |
718 | command == NAND_CMD_READOOB || | |
719 | command == NAND_CMD_SEQIN) { | |
720 | info->buf_count = mtd->writesize + mtd->oobsize; | |
721 | memset(info->data_buff, 0xFF, info->buf_count); | |
722 | } | |
723 | } | |
724 | ||
725 | static int prepare_set_command(struct pxa3xx_nand_info *info, int command, | |
726 | int ext_cmd_type, uint16_t column, int page_addr) | |
727 | { | |
728 | int addr_cycle, exec_cmd; | |
729 | struct pxa3xx_nand_host *host; | |
730 | struct mtd_info *mtd; | |
731 | ||
732 | host = info->host[info->cs]; | |
733 | mtd = host->mtd; | |
734 | addr_cycle = 0; | |
735 | exec_cmd = 1; | |
736 | ||
737 | if (info->cs != 0) | |
738 | info->ndcb0 = NDCB0_CSEL; | |
739 | else | |
740 | info->ndcb0 = 0; | |
741 | ||
742 | if (command == NAND_CMD_SEQIN) | |
743 | exec_cmd = 0; | |
744 | ||
745 | addr_cycle = NDCB0_ADDR_CYC(host->row_addr_cycles | |
746 | + host->col_addr_cycles); | |
747 | ||
748 | switch (command) { | |
749 | case NAND_CMD_READOOB: | |
750 | case NAND_CMD_READ0: | |
751 | info->buf_start = column; | |
752 | info->ndcb0 |= NDCB0_CMD_TYPE(0) | |
753 | | addr_cycle | |
754 | | NAND_CMD_READ0; | |
755 | ||
756 | if (command == NAND_CMD_READOOB) | |
757 | info->buf_start += mtd->writesize; | |
758 | ||
759 | /* | |
760 | * Multiple page read needs an 'extended command type' field, | |
761 | * which is either naked-read or last-read according to the | |
762 | * state. | |
763 | */ | |
764 | if (mtd->writesize == PAGE_CHUNK_SIZE) { | |
765 | info->ndcb0 |= NDCB0_DBC | (NAND_CMD_READSTART << 8); | |
766 | } else if (mtd->writesize > PAGE_CHUNK_SIZE) { | |
767 | info->ndcb0 |= NDCB0_DBC | (NAND_CMD_READSTART << 8) | |
768 | | NDCB0_LEN_OVRD | |
769 | | NDCB0_EXT_CMD_TYPE(ext_cmd_type); | |
770 | info->ndcb3 = info->chunk_size + | |
771 | info->oob_size; | |
772 | } | |
773 | ||
774 | set_command_address(info, mtd->writesize, column, page_addr); | |
775 | break; | |
776 | ||
777 | case NAND_CMD_SEQIN: | |
778 | ||
779 | info->buf_start = column; | |
780 | set_command_address(info, mtd->writesize, 0, page_addr); | |
781 | ||
782 | /* | |
783 | * Multiple page programming needs to execute the initial | |
784 | * SEQIN command that sets the page address. | |
785 | */ | |
786 | if (mtd->writesize > PAGE_CHUNK_SIZE) { | |
787 | info->ndcb0 |= NDCB0_CMD_TYPE(0x1) | |
788 | | NDCB0_EXT_CMD_TYPE(ext_cmd_type) | |
789 | | addr_cycle | |
790 | | command; | |
791 | /* No data transfer in this case */ | |
792 | info->data_size = 0; | |
793 | exec_cmd = 1; | |
794 | } | |
795 | break; | |
796 | ||
797 | case NAND_CMD_PAGEPROG: | |
798 | if (is_buf_blank(info->data_buff, | |
799 | (mtd->writesize + mtd->oobsize))) { | |
800 | exec_cmd = 0; | |
801 | break; | |
802 | } | |
803 | ||
804 | /* Second command setting for large pages */ | |
805 | if (mtd->writesize > PAGE_CHUNK_SIZE) { | |
806 | /* | |
807 | * Multiple page write uses the 'extended command' | |
808 | * field. This can be used to issue a command dispatch | |
809 | * or a naked-write depending on the current stage. | |
810 | */ | |
811 | info->ndcb0 |= NDCB0_CMD_TYPE(0x1) | |
812 | | NDCB0_LEN_OVRD | |
813 | | NDCB0_EXT_CMD_TYPE(ext_cmd_type); | |
814 | info->ndcb3 = info->chunk_size + | |
815 | info->oob_size; | |
816 | ||
817 | /* | |
818 | * This is the command dispatch that completes a chunked | |
819 | * page program operation. | |
820 | */ | |
821 | if (info->data_size == 0) { | |
822 | info->ndcb0 = NDCB0_CMD_TYPE(0x1) | |
823 | | NDCB0_EXT_CMD_TYPE(ext_cmd_type) | |
824 | | command; | |
825 | info->ndcb1 = 0; | |
826 | info->ndcb2 = 0; | |
827 | info->ndcb3 = 0; | |
828 | } | |
829 | } else { | |
830 | info->ndcb0 |= NDCB0_CMD_TYPE(0x1) | |
831 | | NDCB0_AUTO_RS | |
832 | | NDCB0_ST_ROW_EN | |
833 | | NDCB0_DBC | |
834 | | (NAND_CMD_PAGEPROG << 8) | |
835 | | NAND_CMD_SEQIN | |
836 | | addr_cycle; | |
837 | } | |
838 | break; | |
839 | ||
840 | case NAND_CMD_PARAM: | |
841 | info->buf_count = 256; | |
842 | info->ndcb0 |= NDCB0_CMD_TYPE(0) | |
843 | | NDCB0_ADDR_CYC(1) | |
844 | | NDCB0_LEN_OVRD | |
845 | | command; | |
846 | info->ndcb1 = (column & 0xFF); | |
847 | info->ndcb3 = 256; | |
848 | info->data_size = 256; | |
849 | break; | |
850 | ||
851 | case NAND_CMD_READID: | |
852 | info->buf_count = host->read_id_bytes; | |
853 | info->ndcb0 |= NDCB0_CMD_TYPE(3) | |
854 | | NDCB0_ADDR_CYC(1) | |
855 | | command; | |
856 | info->ndcb1 = (column & 0xFF); | |
857 | ||
858 | info->data_size = 8; | |
859 | break; | |
860 | case NAND_CMD_STATUS: | |
861 | info->buf_count = 1; | |
862 | info->ndcb0 |= NDCB0_CMD_TYPE(4) | |
863 | | NDCB0_ADDR_CYC(1) | |
864 | | command; | |
865 | ||
866 | info->data_size = 8; | |
867 | break; | |
868 | ||
869 | case NAND_CMD_ERASE1: | |
870 | info->ndcb0 |= NDCB0_CMD_TYPE(2) | |
871 | | NDCB0_AUTO_RS | |
872 | | NDCB0_ADDR_CYC(3) | |
873 | | NDCB0_DBC | |
874 | | (NAND_CMD_ERASE2 << 8) | |
875 | | NAND_CMD_ERASE1; | |
876 | info->ndcb1 = page_addr; | |
877 | info->ndcb2 = 0; | |
878 | ||
879 | break; | |
880 | case NAND_CMD_RESET: | |
881 | info->ndcb0 |= NDCB0_CMD_TYPE(5) | |
882 | | command; | |
883 | ||
884 | break; | |
885 | ||
886 | case NAND_CMD_ERASE2: | |
887 | exec_cmd = 0; | |
888 | break; | |
889 | ||
890 | default: | |
891 | exec_cmd = 0; | |
892 | dev_err(&info->pdev->dev, "non-supported command %x\n", | |
893 | command); | |
894 | break; | |
895 | } | |
896 | ||
897 | return exec_cmd; | |
898 | } | |
899 | ||
900 | static void nand_cmdfunc(struct mtd_info *mtd, unsigned command, | |
901 | int column, int page_addr) | |
902 | { | |
17cb4b8f SW |
903 | struct nand_chip *chip = mtd_to_nand(mtd); |
904 | struct pxa3xx_nand_host *host = nand_get_controller_data(chip); | |
873960c8 SR |
905 | struct pxa3xx_nand_info *info = host->info_data; |
906 | int exec_cmd; | |
907 | ||
908 | /* | |
909 | * if this is a x16 device ,then convert the input | |
910 | * "byte" address into a "word" address appropriate | |
911 | * for indexing a word-oriented device | |
912 | */ | |
913 | if (info->reg_ndcr & NDCR_DWIDTH_M) | |
914 | column /= 2; | |
915 | ||
916 | /* | |
917 | * There may be different NAND chip hooked to | |
918 | * different chip select, so check whether | |
919 | * chip select has been changed, if yes, reset the timing | |
920 | */ | |
921 | if (info->cs != host->cs) { | |
922 | info->cs = host->cs; | |
923 | nand_writel(info, NDTR0CS0, info->ndtr0cs0); | |
924 | nand_writel(info, NDTR1CS0, info->ndtr1cs0); | |
925 | } | |
926 | ||
927 | prepare_start_command(info, command); | |
928 | ||
929 | info->state = STATE_PREPARED; | |
930 | exec_cmd = prepare_set_command(info, command, 0, column, page_addr); | |
931 | ||
932 | if (exec_cmd) { | |
933 | u32 ts; | |
934 | ||
935 | info->cmd_complete = 0; | |
936 | info->dev_ready = 0; | |
937 | info->need_wait = 1; | |
938 | pxa3xx_nand_start(info); | |
939 | ||
940 | ts = get_timer(0); | |
941 | while (1) { | |
942 | u32 status; | |
943 | ||
944 | status = nand_readl(info, NDSR); | |
945 | if (status) | |
946 | pxa3xx_nand_irq(info); | |
947 | ||
948 | if (info->cmd_complete) | |
949 | break; | |
950 | ||
951 | if (get_timer(ts) > CHIP_DELAY_TIMEOUT) { | |
952 | dev_err(&info->pdev->dev, "Wait timeout!!!\n"); | |
953 | return; | |
954 | } | |
955 | } | |
956 | } | |
957 | info->state = STATE_IDLE; | |
958 | } | |
959 | ||
960 | static void nand_cmdfunc_extended(struct mtd_info *mtd, | |
961 | const unsigned command, | |
962 | int column, int page_addr) | |
963 | { | |
17cb4b8f SW |
964 | struct nand_chip *chip = mtd_to_nand(mtd); |
965 | struct pxa3xx_nand_host *host = nand_get_controller_data(chip); | |
873960c8 SR |
966 | struct pxa3xx_nand_info *info = host->info_data; |
967 | int exec_cmd, ext_cmd_type; | |
968 | ||
969 | /* | |
970 | * if this is a x16 device then convert the input | |
971 | * "byte" address into a "word" address appropriate | |
972 | * for indexing a word-oriented device | |
973 | */ | |
974 | if (info->reg_ndcr & NDCR_DWIDTH_M) | |
975 | column /= 2; | |
976 | ||
977 | /* | |
978 | * There may be different NAND chip hooked to | |
979 | * different chip select, so check whether | |
980 | * chip select has been changed, if yes, reset the timing | |
981 | */ | |
982 | if (info->cs != host->cs) { | |
983 | info->cs = host->cs; | |
984 | nand_writel(info, NDTR0CS0, info->ndtr0cs0); | |
985 | nand_writel(info, NDTR1CS0, info->ndtr1cs0); | |
986 | } | |
987 | ||
988 | /* Select the extended command for the first command */ | |
989 | switch (command) { | |
990 | case NAND_CMD_READ0: | |
991 | case NAND_CMD_READOOB: | |
992 | ext_cmd_type = EXT_CMD_TYPE_MONO; | |
993 | break; | |
994 | case NAND_CMD_SEQIN: | |
995 | ext_cmd_type = EXT_CMD_TYPE_DISPATCH; | |
996 | break; | |
997 | case NAND_CMD_PAGEPROG: | |
998 | ext_cmd_type = EXT_CMD_TYPE_NAKED_RW; | |
999 | break; | |
1000 | default: | |
1001 | ext_cmd_type = 0; | |
1002 | break; | |
1003 | } | |
1004 | ||
1005 | prepare_start_command(info, command); | |
1006 | ||
1007 | /* | |
1008 | * Prepare the "is ready" completion before starting a command | |
1009 | * transaction sequence. If the command is not executed the | |
1010 | * completion will be completed, see below. | |
1011 | * | |
1012 | * We can do that inside the loop because the command variable | |
1013 | * is invariant and thus so is the exec_cmd. | |
1014 | */ | |
1015 | info->need_wait = 1; | |
1016 | info->dev_ready = 0; | |
1017 | ||
1018 | do { | |
1019 | u32 ts; | |
1020 | ||
1021 | info->state = STATE_PREPARED; | |
1022 | exec_cmd = prepare_set_command(info, command, ext_cmd_type, | |
1023 | column, page_addr); | |
1024 | if (!exec_cmd) { | |
1025 | info->need_wait = 0; | |
1026 | info->dev_ready = 1; | |
1027 | break; | |
1028 | } | |
1029 | ||
1030 | info->cmd_complete = 0; | |
1031 | pxa3xx_nand_start(info); | |
1032 | ||
1033 | ts = get_timer(0); | |
1034 | while (1) { | |
1035 | u32 status; | |
1036 | ||
1037 | status = nand_readl(info, NDSR); | |
1038 | if (status) | |
1039 | pxa3xx_nand_irq(info); | |
1040 | ||
1041 | if (info->cmd_complete) | |
1042 | break; | |
1043 | ||
1044 | if (get_timer(ts) > CHIP_DELAY_TIMEOUT) { | |
1045 | dev_err(&info->pdev->dev, "Wait timeout!!!\n"); | |
1046 | return; | |
1047 | } | |
1048 | } | |
1049 | ||
1050 | /* Check if the sequence is complete */ | |
1051 | if (info->data_size == 0 && command != NAND_CMD_PAGEPROG) | |
1052 | break; | |
1053 | ||
1054 | /* | |
1055 | * After a splitted program command sequence has issued | |
1056 | * the command dispatch, the command sequence is complete. | |
1057 | */ | |
1058 | if (info->data_size == 0 && | |
1059 | command == NAND_CMD_PAGEPROG && | |
1060 | ext_cmd_type == EXT_CMD_TYPE_DISPATCH) | |
1061 | break; | |
1062 | ||
1063 | if (command == NAND_CMD_READ0 || command == NAND_CMD_READOOB) { | |
1064 | /* Last read: issue a 'last naked read' */ | |
1065 | if (info->data_size == info->chunk_size) | |
1066 | ext_cmd_type = EXT_CMD_TYPE_LAST_RW; | |
1067 | else | |
1068 | ext_cmd_type = EXT_CMD_TYPE_NAKED_RW; | |
1069 | ||
1070 | /* | |
1071 | * If a splitted program command has no more data to transfer, | |
1072 | * the command dispatch must be issued to complete. | |
1073 | */ | |
1074 | } else if (command == NAND_CMD_PAGEPROG && | |
1075 | info->data_size == 0) { | |
1076 | ext_cmd_type = EXT_CMD_TYPE_DISPATCH; | |
1077 | } | |
1078 | } while (1); | |
1079 | ||
1080 | info->state = STATE_IDLE; | |
1081 | } | |
1082 | ||
1083 | static int pxa3xx_nand_write_page_hwecc(struct mtd_info *mtd, | |
81c77252 SW |
1084 | struct nand_chip *chip, const uint8_t *buf, int oob_required, |
1085 | int page) | |
873960c8 SR |
1086 | { |
1087 | chip->write_buf(mtd, buf, mtd->writesize); | |
1088 | chip->write_buf(mtd, chip->oob_poi, mtd->oobsize); | |
1089 | ||
1090 | return 0; | |
1091 | } | |
1092 | ||
1093 | static int pxa3xx_nand_read_page_hwecc(struct mtd_info *mtd, | |
1094 | struct nand_chip *chip, uint8_t *buf, int oob_required, | |
1095 | int page) | |
1096 | { | |
17cb4b8f | 1097 | struct pxa3xx_nand_host *host = nand_get_controller_data(chip); |
873960c8 SR |
1098 | struct pxa3xx_nand_info *info = host->info_data; |
1099 | ||
1100 | chip->read_buf(mtd, buf, mtd->writesize); | |
1101 | chip->read_buf(mtd, chip->oob_poi, mtd->oobsize); | |
1102 | ||
1103 | if (info->retcode == ERR_CORERR && info->use_ecc) { | |
1104 | mtd->ecc_stats.corrected += info->ecc_err_cnt; | |
1105 | ||
1106 | } else if (info->retcode == ERR_UNCORERR) { | |
1107 | /* | |
1108 | * for blank page (all 0xff), HW will calculate its ECC as | |
1109 | * 0, which is different from the ECC information within | |
1110 | * OOB, ignore such uncorrectable errors | |
1111 | */ | |
1112 | if (is_buf_blank(buf, mtd->writesize)) | |
1113 | info->retcode = ERR_NONE; | |
1114 | else | |
1115 | mtd->ecc_stats.failed++; | |
1116 | } | |
1117 | ||
1118 | return info->max_bitflips; | |
1119 | } | |
1120 | ||
1121 | static uint8_t pxa3xx_nand_read_byte(struct mtd_info *mtd) | |
1122 | { | |
17cb4b8f SW |
1123 | struct nand_chip *chip = mtd_to_nand(mtd); |
1124 | struct pxa3xx_nand_host *host = nand_get_controller_data(chip); | |
873960c8 SR |
1125 | struct pxa3xx_nand_info *info = host->info_data; |
1126 | char retval = 0xFF; | |
1127 | ||
1128 | if (info->buf_start < info->buf_count) | |
1129 | /* Has just send a new command? */ | |
1130 | retval = info->data_buff[info->buf_start++]; | |
1131 | ||
1132 | return retval; | |
1133 | } | |
1134 | ||
1135 | static u16 pxa3xx_nand_read_word(struct mtd_info *mtd) | |
1136 | { | |
17cb4b8f SW |
1137 | struct nand_chip *chip = mtd_to_nand(mtd); |
1138 | struct pxa3xx_nand_host *host = nand_get_controller_data(chip); | |
873960c8 SR |
1139 | struct pxa3xx_nand_info *info = host->info_data; |
1140 | u16 retval = 0xFFFF; | |
1141 | ||
1142 | if (!(info->buf_start & 0x01) && info->buf_start < info->buf_count) { | |
1143 | retval = *((u16 *)(info->data_buff+info->buf_start)); | |
1144 | info->buf_start += 2; | |
1145 | } | |
1146 | return retval; | |
1147 | } | |
1148 | ||
1149 | static void pxa3xx_nand_read_buf(struct mtd_info *mtd, uint8_t *buf, int len) | |
1150 | { | |
17cb4b8f SW |
1151 | struct nand_chip *chip = mtd_to_nand(mtd); |
1152 | struct pxa3xx_nand_host *host = nand_get_controller_data(chip); | |
873960c8 SR |
1153 | struct pxa3xx_nand_info *info = host->info_data; |
1154 | int real_len = min_t(size_t, len, info->buf_count - info->buf_start); | |
1155 | ||
1156 | memcpy(buf, info->data_buff + info->buf_start, real_len); | |
1157 | info->buf_start += real_len; | |
1158 | } | |
1159 | ||
1160 | static void pxa3xx_nand_write_buf(struct mtd_info *mtd, | |
1161 | const uint8_t *buf, int len) | |
1162 | { | |
17cb4b8f SW |
1163 | struct nand_chip *chip = mtd_to_nand(mtd); |
1164 | struct pxa3xx_nand_host *host = nand_get_controller_data(chip); | |
873960c8 SR |
1165 | struct pxa3xx_nand_info *info = host->info_data; |
1166 | int real_len = min_t(size_t, len, info->buf_count - info->buf_start); | |
1167 | ||
1168 | memcpy(info->data_buff + info->buf_start, buf, real_len); | |
1169 | info->buf_start += real_len; | |
1170 | } | |
1171 | ||
1172 | static void pxa3xx_nand_select_chip(struct mtd_info *mtd, int chip) | |
1173 | { | |
1174 | return; | |
1175 | } | |
1176 | ||
1177 | static int pxa3xx_nand_waitfunc(struct mtd_info *mtd, struct nand_chip *this) | |
1178 | { | |
17cb4b8f SW |
1179 | struct nand_chip *chip = mtd_to_nand(mtd); |
1180 | struct pxa3xx_nand_host *host = nand_get_controller_data(chip); | |
873960c8 SR |
1181 | struct pxa3xx_nand_info *info = host->info_data; |
1182 | ||
1183 | if (info->need_wait) { | |
1184 | u32 ts; | |
1185 | ||
1186 | info->need_wait = 0; | |
1187 | ||
1188 | ts = get_timer(0); | |
1189 | while (1) { | |
1190 | u32 status; | |
1191 | ||
1192 | status = nand_readl(info, NDSR); | |
1193 | if (status) | |
1194 | pxa3xx_nand_irq(info); | |
1195 | ||
1196 | if (info->dev_ready) | |
1197 | break; | |
1198 | ||
1199 | if (get_timer(ts) > CHIP_DELAY_TIMEOUT) { | |
1200 | dev_err(&info->pdev->dev, "Ready timeout!!!\n"); | |
1201 | return NAND_STATUS_FAIL; | |
1202 | } | |
1203 | } | |
1204 | } | |
1205 | ||
1206 | /* pxa3xx_nand_send_command has waited for command complete */ | |
1207 | if (this->state == FL_WRITING || this->state == FL_ERASING) { | |
1208 | if (info->retcode == ERR_NONE) | |
1209 | return 0; | |
1210 | else | |
1211 | return NAND_STATUS_FAIL; | |
1212 | } | |
1213 | ||
1214 | return NAND_STATUS_READY; | |
1215 | } | |
1216 | ||
1217 | static int pxa3xx_nand_config_flash(struct pxa3xx_nand_info *info) | |
1218 | { | |
1219 | struct pxa3xx_nand_host *host = info->host[info->cs]; | |
1220 | struct mtd_info *mtd = host->mtd; | |
17cb4b8f | 1221 | struct nand_chip *chip = mtd_to_nand(mtd); |
873960c8 SR |
1222 | |
1223 | info->reg_ndcr |= (host->col_addr_cycles == 2) ? NDCR_RA_START : 0; | |
1224 | info->reg_ndcr |= (chip->page_shift == 6) ? NDCR_PG_PER_BLK : 0; | |
1225 | info->reg_ndcr |= (mtd->writesize == 2048) ? NDCR_PAGE_SZ : 0; | |
1226 | ||
1227 | return 0; | |
1228 | } | |
1229 | ||
1230 | static int pxa3xx_nand_detect_config(struct pxa3xx_nand_info *info) | |
1231 | { | |
1232 | /* | |
1233 | * We set 0 by hard coding here, for we don't support keep_config | |
1234 | * when there is more than one chip attached to the controller | |
1235 | */ | |
1236 | struct pxa3xx_nand_host *host = info->host[0]; | |
1237 | uint32_t ndcr = nand_readl(info, NDCR); | |
1238 | ||
1239 | if (ndcr & NDCR_PAGE_SZ) { | |
1240 | /* Controller's FIFO size */ | |
1241 | info->chunk_size = 2048; | |
1242 | host->read_id_bytes = 4; | |
1243 | } else { | |
1244 | info->chunk_size = 512; | |
1245 | host->read_id_bytes = 2; | |
1246 | } | |
1247 | ||
1248 | /* Set an initial chunk size */ | |
1249 | info->reg_ndcr = ndcr & ~NDCR_INT_MASK; | |
1250 | info->ndtr0cs0 = nand_readl(info, NDTR0CS0); | |
1251 | info->ndtr1cs0 = nand_readl(info, NDTR1CS0); | |
1252 | return 0; | |
1253 | } | |
1254 | ||
1255 | static int pxa3xx_nand_init_buff(struct pxa3xx_nand_info *info) | |
1256 | { | |
1257 | info->data_buff = kmalloc(info->buf_size, GFP_KERNEL); | |
1258 | if (info->data_buff == NULL) | |
1259 | return -ENOMEM; | |
1260 | return 0; | |
1261 | } | |
1262 | ||
1263 | static int pxa3xx_nand_sensing(struct pxa3xx_nand_host *host) | |
1264 | { | |
1265 | struct pxa3xx_nand_info *info = host->info_data; | |
1266 | struct pxa3xx_nand_platform_data *pdata = info->pdata; | |
1267 | struct mtd_info *mtd; | |
1268 | struct nand_chip *chip; | |
1269 | const struct nand_sdr_timings *timings; | |
1270 | int ret; | |
1271 | ||
1272 | mtd = info->host[info->cs]->mtd; | |
17cb4b8f | 1273 | chip = mtd_to_nand(mtd); |
873960c8 SR |
1274 | |
1275 | /* configure default flash values */ | |
1276 | info->reg_ndcr = 0x0; /* enable all interrupts */ | |
1277 | info->reg_ndcr |= (pdata->enable_arbiter) ? NDCR_ND_ARB_EN : 0; | |
1278 | info->reg_ndcr |= NDCR_RD_ID_CNT(host->read_id_bytes); | |
1279 | info->reg_ndcr |= NDCR_SPARE_EN; /* enable spare by default */ | |
1280 | ||
1281 | /* use the common timing to make a try */ | |
1282 | timings = onfi_async_timing_mode_to_sdr_timings(0); | |
1283 | if (IS_ERR(timings)) | |
1284 | return PTR_ERR(timings); | |
1285 | ||
1286 | pxa3xx_nand_set_sdr_timing(host, timings); | |
1287 | ||
1288 | chip->cmdfunc(mtd, NAND_CMD_RESET, 0, 0); | |
1289 | ret = chip->waitfunc(mtd, chip); | |
1290 | if (ret & NAND_STATUS_FAIL) | |
1291 | return -ENODEV; | |
1292 | ||
1293 | return 0; | |
1294 | } | |
1295 | ||
1296 | static int pxa_ecc_init(struct pxa3xx_nand_info *info, | |
1297 | struct nand_ecc_ctrl *ecc, | |
1298 | int strength, int ecc_stepsize, int page_size) | |
1299 | { | |
1300 | if (strength == 1 && ecc_stepsize == 512 && page_size == 2048) { | |
1301 | info->chunk_size = 2048; | |
1302 | info->spare_size = 40; | |
1303 | info->ecc_size = 24; | |
1304 | ecc->mode = NAND_ECC_HW; | |
1305 | ecc->size = 512; | |
1306 | ecc->strength = 1; | |
1307 | ||
1308 | } else if (strength == 1 && ecc_stepsize == 512 && page_size == 512) { | |
1309 | info->chunk_size = 512; | |
1310 | info->spare_size = 8; | |
1311 | info->ecc_size = 8; | |
1312 | ecc->mode = NAND_ECC_HW; | |
1313 | ecc->size = 512; | |
1314 | ecc->strength = 1; | |
1315 | ||
1316 | /* | |
1317 | * Required ECC: 4-bit correction per 512 bytes | |
1318 | * Select: 16-bit correction per 2048 bytes | |
1319 | */ | |
1320 | } else if (strength == 4 && ecc_stepsize == 512 && page_size == 2048) { | |
1321 | info->ecc_bch = 1; | |
1322 | info->chunk_size = 2048; | |
1323 | info->spare_size = 32; | |
1324 | info->ecc_size = 32; | |
1325 | ecc->mode = NAND_ECC_HW; | |
1326 | ecc->size = info->chunk_size; | |
1327 | ecc->layout = &ecc_layout_2KB_bch4bit; | |
1328 | ecc->strength = 16; | |
1329 | ||
1330 | } else if (strength == 4 && ecc_stepsize == 512 && page_size == 4096) { | |
1331 | info->ecc_bch = 1; | |
1332 | info->chunk_size = 2048; | |
1333 | info->spare_size = 32; | |
1334 | info->ecc_size = 32; | |
1335 | ecc->mode = NAND_ECC_HW; | |
1336 | ecc->size = info->chunk_size; | |
1337 | ecc->layout = &ecc_layout_4KB_bch4bit; | |
1338 | ecc->strength = 16; | |
1339 | ||
1340 | /* | |
1341 | * Required ECC: 8-bit correction per 512 bytes | |
1342 | * Select: 16-bit correction per 1024 bytes | |
1343 | */ | |
1344 | } else if (strength == 8 && ecc_stepsize == 512 && page_size == 4096) { | |
1345 | info->ecc_bch = 1; | |
1346 | info->chunk_size = 1024; | |
1347 | info->spare_size = 0; | |
1348 | info->ecc_size = 32; | |
1349 | ecc->mode = NAND_ECC_HW; | |
1350 | ecc->size = info->chunk_size; | |
1351 | ecc->layout = &ecc_layout_4KB_bch8bit; | |
1352 | ecc->strength = 16; | |
1353 | } else { | |
1354 | dev_err(&info->pdev->dev, | |
1355 | "ECC strength %d at page size %d is not supported\n", | |
1356 | strength, page_size); | |
1357 | return -ENODEV; | |
1358 | } | |
1359 | ||
1360 | return 0; | |
1361 | } | |
1362 | ||
1363 | static int pxa3xx_nand_scan(struct mtd_info *mtd) | |
1364 | { | |
17cb4b8f SW |
1365 | struct nand_chip *chip = mtd_to_nand(mtd); |
1366 | struct pxa3xx_nand_host *host = nand_get_controller_data(chip); | |
873960c8 SR |
1367 | struct pxa3xx_nand_info *info = host->info_data; |
1368 | struct pxa3xx_nand_platform_data *pdata = info->pdata; | |
873960c8 SR |
1369 | int ret; |
1370 | uint16_t ecc_strength, ecc_step; | |
1371 | ||
1372 | if (pdata->keep_config && !pxa3xx_nand_detect_config(info)) | |
1373 | goto KEEP_CONFIG; | |
1374 | ||
1375 | /* Set a default chunk size */ | |
1376 | info->chunk_size = 512; | |
1377 | ||
1378 | ret = pxa3xx_nand_sensing(host); | |
1379 | if (ret) { | |
1380 | dev_info(&info->pdev->dev, "There is no chip on cs %d!\n", | |
1381 | info->cs); | |
1382 | ||
1383 | return ret; | |
1384 | } | |
1385 | ||
1386 | KEEP_CONFIG: | |
1387 | /* Device detection must be done with ECC disabled */ | |
1388 | if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370) | |
1389 | nand_writel(info, NDECCCTRL, 0x0); | |
1390 | ||
1391 | if (nand_scan_ident(mtd, 1, NULL)) | |
1392 | return -ENODEV; | |
1393 | ||
1394 | if (!pdata->keep_config) { | |
1395 | ret = pxa3xx_nand_init_timings(host); | |
1396 | if (ret) { | |
1397 | dev_err(&info->pdev->dev, | |
1398 | "Failed to set timings: %d\n", ret); | |
1399 | return ret; | |
1400 | } | |
1401 | } | |
1402 | ||
1403 | ret = pxa3xx_nand_config_flash(info); | |
1404 | if (ret) | |
1405 | return ret; | |
1406 | ||
1407 | #ifdef CONFIG_SYS_NAND_USE_FLASH_BBT | |
1408 | /* | |
1409 | * We'll use a bad block table stored in-flash and don't | |
1410 | * allow writing the bad block marker to the flash. | |
1411 | */ | |
1412 | chip->bbt_options |= NAND_BBT_USE_FLASH | NAND_BBT_NO_OOB_BBM; | |
1413 | chip->bbt_td = &bbt_main_descr; | |
1414 | chip->bbt_md = &bbt_mirror_descr; | |
1415 | #endif | |
1416 | ||
1417 | /* | |
1418 | * If the page size is bigger than the FIFO size, let's check | |
1419 | * we are given the right variant and then switch to the extended | |
1420 | * (aka splitted) command handling, | |
1421 | */ | |
1422 | if (mtd->writesize > PAGE_CHUNK_SIZE) { | |
1423 | if (info->variant == PXA3XX_NAND_VARIANT_ARMADA370) { | |
1424 | chip->cmdfunc = nand_cmdfunc_extended; | |
1425 | } else { | |
1426 | dev_err(&info->pdev->dev, | |
1427 | "unsupported page size on this variant\n"); | |
1428 | return -ENODEV; | |
1429 | } | |
1430 | } | |
1431 | ||
1432 | if (pdata->ecc_strength && pdata->ecc_step_size) { | |
1433 | ecc_strength = pdata->ecc_strength; | |
1434 | ecc_step = pdata->ecc_step_size; | |
1435 | } else { | |
1436 | ecc_strength = chip->ecc_strength_ds; | |
1437 | ecc_step = chip->ecc_step_ds; | |
1438 | } | |
1439 | ||
1440 | /* Set default ECC strength requirements on non-ONFI devices */ | |
1441 | if (ecc_strength < 1 && ecc_step < 1) { | |
1442 | ecc_strength = 1; | |
1443 | ecc_step = 512; | |
1444 | } | |
1445 | ||
1446 | ret = pxa_ecc_init(info, &chip->ecc, ecc_strength, | |
1447 | ecc_step, mtd->writesize); | |
1448 | if (ret) | |
1449 | return ret; | |
1450 | ||
1451 | /* calculate addressing information */ | |
1452 | if (mtd->writesize >= 2048) | |
1453 | host->col_addr_cycles = 2; | |
1454 | else | |
1455 | host->col_addr_cycles = 1; | |
1456 | ||
1457 | /* release the initial buffer */ | |
1458 | kfree(info->data_buff); | |
1459 | ||
1460 | /* allocate the real data + oob buffer */ | |
1461 | info->buf_size = mtd->writesize + mtd->oobsize; | |
1462 | ret = pxa3xx_nand_init_buff(info); | |
1463 | if (ret) | |
1464 | return ret; | |
1465 | info->oob_buff = info->data_buff + mtd->writesize; | |
1466 | ||
1467 | if ((mtd->size >> chip->page_shift) > 65536) | |
1468 | host->row_addr_cycles = 3; | |
1469 | else | |
1470 | host->row_addr_cycles = 2; | |
1471 | return nand_scan_tail(mtd); | |
1472 | } | |
1473 | ||
1474 | static int alloc_nand_resource(struct pxa3xx_nand_info *info) | |
1475 | { | |
1476 | struct pxa3xx_nand_platform_data *pdata; | |
1477 | struct pxa3xx_nand_host *host; | |
1478 | struct nand_chip *chip = NULL; | |
1479 | struct mtd_info *mtd; | |
1480 | int ret, cs; | |
1481 | ||
1482 | pdata = info->pdata; | |
1483 | if (pdata->num_cs <= 0) | |
1484 | return -ENODEV; | |
1485 | ||
1486 | info->variant = pxa3xx_nand_get_variant(); | |
1487 | for (cs = 0; cs < pdata->num_cs; cs++) { | |
84caff35 KS |
1488 | chip = (struct nand_chip *) |
1489 | ((u8 *)&info[1] + sizeof(*host) * cs); | |
17cb4b8f | 1490 | mtd = nand_to_mtd(chip); |
873960c8 SR |
1491 | host = (struct pxa3xx_nand_host *)chip; |
1492 | info->host[cs] = host; | |
1493 | host->mtd = mtd; | |
1494 | host->cs = cs; | |
1495 | host->info_data = info; | |
1496 | host->read_id_bytes = 4; | |
873960c8 SR |
1497 | mtd->owner = THIS_MODULE; |
1498 | ||
91395b5d | 1499 | nand_set_controller_data(chip, host); |
873960c8 SR |
1500 | chip->ecc.read_page = pxa3xx_nand_read_page_hwecc; |
1501 | chip->ecc.write_page = pxa3xx_nand_write_page_hwecc; | |
1502 | chip->controller = &info->controller; | |
1503 | chip->waitfunc = pxa3xx_nand_waitfunc; | |
1504 | chip->select_chip = pxa3xx_nand_select_chip; | |
1505 | chip->read_word = pxa3xx_nand_read_word; | |
1506 | chip->read_byte = pxa3xx_nand_read_byte; | |
1507 | chip->read_buf = pxa3xx_nand_read_buf; | |
1508 | chip->write_buf = pxa3xx_nand_write_buf; | |
1509 | chip->options |= NAND_NO_SUBPAGE_WRITE; | |
1510 | chip->cmdfunc = nand_cmdfunc; | |
1511 | } | |
1512 | ||
1513 | info->mmio_base = (void __iomem *)MVEBU_NAND_BASE; | |
1514 | ||
1515 | /* Allocate a buffer to allow flash detection */ | |
1516 | info->buf_size = INIT_BUFFER_SIZE; | |
1517 | info->data_buff = kmalloc(info->buf_size, GFP_KERNEL); | |
1518 | if (info->data_buff == NULL) { | |
1519 | ret = -ENOMEM; | |
1520 | goto fail_disable_clk; | |
1521 | } | |
1522 | ||
1523 | /* initialize all interrupts to be disabled */ | |
1524 | disable_int(info, NDSR_MASK); | |
1525 | ||
1526 | return 0; | |
1527 | ||
1528 | kfree(info->data_buff); | |
1529 | fail_disable_clk: | |
1530 | return ret; | |
1531 | } | |
1532 | ||
1533 | static int pxa3xx_nand_probe_dt(struct pxa3xx_nand_info *info) | |
1534 | { | |
1535 | struct pxa3xx_nand_platform_data *pdata; | |
1536 | ||
1537 | pdata = kzalloc(sizeof(*pdata), GFP_KERNEL); | |
1538 | if (!pdata) | |
1539 | return -ENOMEM; | |
1540 | ||
1541 | pdata->enable_arbiter = 1; | |
1542 | pdata->num_cs = 1; | |
1543 | ||
1544 | info->pdata = pdata; | |
1545 | ||
1546 | return 0; | |
1547 | } | |
1548 | ||
1549 | static int pxa3xx_nand_probe(struct pxa3xx_nand_info *info) | |
1550 | { | |
1551 | struct pxa3xx_nand_platform_data *pdata; | |
1552 | int ret, cs, probe_success; | |
1553 | ||
1554 | ret = pxa3xx_nand_probe_dt(info); | |
1555 | if (ret) | |
1556 | return ret; | |
1557 | ||
1558 | pdata = info->pdata; | |
1559 | ||
1560 | ret = alloc_nand_resource(info); | |
1561 | if (ret) { | |
1562 | dev_err(&pdev->dev, "alloc nand resource failed\n"); | |
1563 | return ret; | |
1564 | } | |
1565 | ||
1566 | probe_success = 0; | |
1567 | for (cs = 0; cs < pdata->num_cs; cs++) { | |
1568 | struct mtd_info *mtd = info->host[cs]->mtd; | |
1569 | ||
1570 | /* | |
1571 | * The mtd name matches the one used in 'mtdparts' kernel | |
1572 | * parameter. This name cannot be changed or otherwise | |
1573 | * user's mtd partitions configuration would get broken. | |
1574 | */ | |
1575 | mtd->name = "pxa3xx_nand-0"; | |
1576 | info->cs = cs; | |
1577 | ret = pxa3xx_nand_scan(mtd); | |
1578 | if (ret) { | |
1579 | dev_info(&pdev->dev, "failed to scan nand at cs %d\n", | |
1580 | cs); | |
1581 | continue; | |
1582 | } | |
1583 | ||
b616d9b0 SW |
1584 | if (nand_register(cs, mtd)) |
1585 | continue; | |
1586 | ||
1587 | probe_success = 1; | |
873960c8 SR |
1588 | } |
1589 | ||
1590 | if (!probe_success) | |
1591 | return -ENODEV; | |
1592 | ||
1593 | return 0; | |
1594 | } | |
1595 | ||
1596 | /* | |
1597 | * Main initialization routine | |
1598 | */ | |
1599 | void board_nand_init(void) | |
1600 | { | |
1601 | struct pxa3xx_nand_info *info; | |
1602 | struct pxa3xx_nand_host *host; | |
1603 | int ret; | |
1604 | ||
065a373d KS |
1605 | info = kzalloc(sizeof(*info) + |
1606 | sizeof(*host) * CONFIG_SYS_MAX_NAND_DEVICE, | |
1607 | GFP_KERNEL); | |
873960c8 SR |
1608 | if (!info) |
1609 | return; | |
1610 | ||
873960c8 SR |
1611 | ret = pxa3xx_nand_probe(info); |
1612 | if (ret) | |
1613 | return; | |
873960c8 | 1614 | } |