]>
Commit | Line | Data |
---|---|---|
c752cd2a | 1 | #include <common.h> |
24b852a7 | 2 | #include <console.h> |
ce5207e1 | 3 | #include "e1000.h" |
deb7282f | 4 | #include <linux/compiler.h> |
ce5207e1 KM |
5 | |
6 | /*----------------------------------------------------------------------- | |
7 | * SPI transfer | |
8 | * | |
9 | * This writes "bitlen" bits out the SPI MOSI port and simultaneously clocks | |
10 | * "bitlen" bits in the SPI MISO port. That's just the way SPI works. | |
11 | * | |
12 | * The source of the outgoing bits is the "dout" parameter and the | |
13 | * destination of the input bits is the "din" parameter. Note that "dout" | |
14 | * and "din" can point to the same memory location, in which case the | |
15 | * input data overwrites the output data (since both are buffered by | |
16 | * temporary variables, this is OK). | |
17 | * | |
18 | * This may be interrupted with Ctrl-C if "intr" is true, otherwise it will | |
19 | * never return an error. | |
20 | */ | |
21 | static int e1000_spi_xfer(struct e1000_hw *hw, unsigned int bitlen, | |
472d5460 | 22 | const void *dout_mem, void *din_mem, bool intr) |
ce5207e1 KM |
23 | { |
24 | const uint8_t *dout = dout_mem; | |
25 | uint8_t *din = din_mem; | |
26 | ||
27 | uint8_t mask = 0; | |
28 | uint32_t eecd; | |
29 | unsigned long i; | |
30 | ||
31 | /* Pre-read the control register */ | |
32 | eecd = E1000_READ_REG(hw, EECD); | |
33 | ||
34 | /* Iterate over each bit */ | |
35 | for (i = 0, mask = 0x80; i < bitlen; i++, mask = (mask >> 1)?:0x80) { | |
36 | /* Check for interrupt */ | |
37 | if (intr && ctrlc()) | |
38 | return -1; | |
39 | ||
40 | /* Determine the output bit */ | |
41 | if (dout && dout[i >> 3] & mask) | |
42 | eecd |= E1000_EECD_DI; | |
43 | else | |
44 | eecd &= ~E1000_EECD_DI; | |
45 | ||
46 | /* Write the output bit and wait 50us */ | |
47 | E1000_WRITE_REG(hw, EECD, eecd); | |
48 | E1000_WRITE_FLUSH(hw); | |
49 | udelay(50); | |
50 | ||
51 | /* Poke the clock (waits 50us) */ | |
52 | e1000_raise_ee_clk(hw, &eecd); | |
53 | ||
54 | /* Now read the input bit */ | |
55 | eecd = E1000_READ_REG(hw, EECD); | |
56 | if (din) { | |
57 | if (eecd & E1000_EECD_DO) | |
58 | din[i >> 3] |= mask; | |
59 | else | |
60 | din[i >> 3] &= ~mask; | |
61 | } | |
62 | ||
63 | /* Poke the clock again (waits 50us) */ | |
64 | e1000_lower_ee_clk(hw, &eecd); | |
65 | } | |
66 | ||
67 | /* Now clear any remaining bits of the input */ | |
68 | if (din && (i & 7)) | |
69 | din[i >> 3] &= ~((mask << 1) - 1); | |
70 | ||
71 | return 0; | |
72 | } | |
73 | ||
74 | #ifdef CONFIG_E1000_SPI_GENERIC | |
75 | static inline struct e1000_hw *e1000_hw_from_spi(struct spi_slave *spi) | |
76 | { | |
77 | return container_of(spi, struct e1000_hw, spi); | |
78 | } | |
79 | ||
80 | /* Not sure why all of these are necessary */ | |
81 | void spi_init_r(void) { /* Nothing to do */ } | |
82 | void spi_init_f(void) { /* Nothing to do */ } | |
83 | void spi_init(void) { /* Nothing to do */ } | |
84 | ||
85 | struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs, | |
86 | unsigned int max_hz, unsigned int mode) | |
87 | { | |
88 | /* Find the right PCI device */ | |
89 | struct e1000_hw *hw = e1000_find_card(bus); | |
90 | if (!hw) { | |
91 | printf("ERROR: No such e1000 device: e1000#%u\n", bus); | |
92 | return NULL; | |
93 | } | |
94 | ||
95 | /* Make sure it has an SPI chip */ | |
96 | if (hw->eeprom.type != e1000_eeprom_spi) { | |
97 | E1000_ERR(hw->nic, "No attached SPI EEPROM found!\n"); | |
98 | return NULL; | |
99 | } | |
100 | ||
101 | /* Argument sanity checks */ | |
102 | if (cs != 0) { | |
103 | E1000_ERR(hw->nic, "No such SPI chip: %u\n", cs); | |
104 | return NULL; | |
105 | } | |
106 | if (mode != SPI_MODE_0) { | |
107 | E1000_ERR(hw->nic, "Only SPI MODE-0 is supported!\n"); | |
108 | return NULL; | |
109 | } | |
110 | ||
111 | /* TODO: Use max_hz somehow */ | |
112 | E1000_DBG(hw->nic, "EEPROM SPI access requested\n"); | |
113 | return &hw->spi; | |
114 | } | |
115 | ||
116 | void spi_free_slave(struct spi_slave *spi) | |
117 | { | |
deb7282f | 118 | __maybe_unused struct e1000_hw *hw = e1000_hw_from_spi(spi); |
ce5207e1 KM |
119 | E1000_DBG(hw->nic, "EEPROM SPI access released\n"); |
120 | } | |
121 | ||
122 | int spi_claim_bus(struct spi_slave *spi) | |
123 | { | |
124 | struct e1000_hw *hw = e1000_hw_from_spi(spi); | |
125 | ||
126 | if (e1000_acquire_eeprom(hw)) { | |
127 | E1000_ERR(hw->nic, "EEPROM SPI cannot be acquired!\n"); | |
128 | return -1; | |
129 | } | |
130 | ||
131 | return 0; | |
132 | } | |
133 | ||
134 | void spi_release_bus(struct spi_slave *spi) | |
135 | { | |
136 | struct e1000_hw *hw = e1000_hw_from_spi(spi); | |
137 | e1000_release_eeprom(hw); | |
138 | } | |
139 | ||
140 | /* Skinny wrapper around e1000_spi_xfer */ | |
141 | int spi_xfer(struct spi_slave *spi, unsigned int bitlen, | |
142 | const void *dout_mem, void *din_mem, unsigned long flags) | |
143 | { | |
144 | struct e1000_hw *hw = e1000_hw_from_spi(spi); | |
145 | int ret; | |
146 | ||
147 | if (flags & SPI_XFER_BEGIN) | |
148 | e1000_standby_eeprom(hw); | |
149 | ||
472d5460 | 150 | ret = e1000_spi_xfer(hw, bitlen, dout_mem, din_mem, true); |
ce5207e1 KM |
151 | |
152 | if (flags & SPI_XFER_END) | |
153 | e1000_standby_eeprom(hw); | |
154 | ||
155 | return ret; | |
156 | } | |
157 | ||
158 | #endif /* not CONFIG_E1000_SPI_GENERIC */ | |
159 | ||
160 | #ifdef CONFIG_CMD_E1000 | |
161 | ||
162 | /* The EEPROM opcodes */ | |
163 | #define SPI_EEPROM_ENABLE_WR 0x06 | |
164 | #define SPI_EEPROM_DISABLE_WR 0x04 | |
165 | #define SPI_EEPROM_WRITE_STATUS 0x01 | |
166 | #define SPI_EEPROM_READ_STATUS 0x05 | |
167 | #define SPI_EEPROM_WRITE_PAGE 0x02 | |
168 | #define SPI_EEPROM_READ_PAGE 0x03 | |
169 | ||
170 | /* The EEPROM status bits */ | |
171 | #define SPI_EEPROM_STATUS_BUSY 0x01 | |
172 | #define SPI_EEPROM_STATUS_WREN 0x02 | |
173 | ||
472d5460 | 174 | static int e1000_spi_eeprom_enable_wr(struct e1000_hw *hw, bool intr) |
ce5207e1 KM |
175 | { |
176 | u8 op[] = { SPI_EEPROM_ENABLE_WR }; | |
177 | e1000_standby_eeprom(hw); | |
178 | return e1000_spi_xfer(hw, 8*sizeof(op), op, NULL, intr); | |
179 | } | |
180 | ||
181 | /* | |
182 | * These have been tested to perform correctly, but they are not used by any | |
183 | * of the EEPROM commands at this time. | |
184 | */ | |
185 | #if 0 | |
472d5460 | 186 | static int e1000_spi_eeprom_disable_wr(struct e1000_hw *hw, bool intr) |
ce5207e1 KM |
187 | { |
188 | u8 op[] = { SPI_EEPROM_DISABLE_WR }; | |
189 | e1000_standby_eeprom(hw); | |
190 | return e1000_spi_xfer(hw, 8*sizeof(op), op, NULL, intr); | |
191 | } | |
192 | ||
193 | static int e1000_spi_eeprom_write_status(struct e1000_hw *hw, | |
472d5460 | 194 | u8 status, bool intr) |
ce5207e1 KM |
195 | { |
196 | u8 op[] = { SPI_EEPROM_WRITE_STATUS, status }; | |
197 | e1000_standby_eeprom(hw); | |
198 | return e1000_spi_xfer(hw, 8*sizeof(op), op, NULL, intr); | |
199 | } | |
200 | #endif | |
201 | ||
472d5460 | 202 | static int e1000_spi_eeprom_read_status(struct e1000_hw *hw, bool intr) |
ce5207e1 KM |
203 | { |
204 | u8 op[] = { SPI_EEPROM_READ_STATUS, 0 }; | |
205 | e1000_standby_eeprom(hw); | |
206 | if (e1000_spi_xfer(hw, 8*sizeof(op), op, op, intr)) | |
207 | return -1; | |
208 | return op[1]; | |
209 | } | |
210 | ||
211 | static int e1000_spi_eeprom_write_page(struct e1000_hw *hw, | |
472d5460 | 212 | const void *data, u16 off, u16 len, bool intr) |
ce5207e1 KM |
213 | { |
214 | u8 op[] = { | |
215 | SPI_EEPROM_WRITE_PAGE, | |
216 | (off >> (hw->eeprom.address_bits - 8)) & 0xff, off & 0xff | |
217 | }; | |
218 | ||
219 | e1000_standby_eeprom(hw); | |
220 | ||
221 | if (e1000_spi_xfer(hw, 8 + hw->eeprom.address_bits, op, NULL, intr)) | |
222 | return -1; | |
223 | if (e1000_spi_xfer(hw, len << 3, data, NULL, intr)) | |
224 | return -1; | |
225 | ||
226 | return 0; | |
227 | } | |
228 | ||
229 | static int e1000_spi_eeprom_read_page(struct e1000_hw *hw, | |
472d5460 | 230 | void *data, u16 off, u16 len, bool intr) |
ce5207e1 KM |
231 | { |
232 | u8 op[] = { | |
233 | SPI_EEPROM_READ_PAGE, | |
234 | (off >> (hw->eeprom.address_bits - 8)) & 0xff, off & 0xff | |
235 | }; | |
236 | ||
237 | e1000_standby_eeprom(hw); | |
238 | ||
239 | if (e1000_spi_xfer(hw, 8 + hw->eeprom.address_bits, op, NULL, intr)) | |
240 | return -1; | |
241 | if (e1000_spi_xfer(hw, len << 3, NULL, data, intr)) | |
242 | return -1; | |
243 | ||
244 | return 0; | |
245 | } | |
246 | ||
472d5460 | 247 | static int e1000_spi_eeprom_poll_ready(struct e1000_hw *hw, bool intr) |
ce5207e1 KM |
248 | { |
249 | int status; | |
250 | while ((status = e1000_spi_eeprom_read_status(hw, intr)) >= 0) { | |
251 | if (!(status & SPI_EEPROM_STATUS_BUSY)) | |
252 | return 0; | |
253 | } | |
254 | return -1; | |
255 | } | |
256 | ||
257 | static int e1000_spi_eeprom_dump(struct e1000_hw *hw, | |
472d5460 | 258 | void *data, u16 off, unsigned int len, bool intr) |
ce5207e1 KM |
259 | { |
260 | /* Interruptibly wait for the EEPROM to be ready */ | |
261 | if (e1000_spi_eeprom_poll_ready(hw, intr)) | |
262 | return -1; | |
263 | ||
264 | /* Dump each page in sequence */ | |
265 | while (len) { | |
266 | /* Calculate the data bytes on this page */ | |
267 | u16 pg_off = off & (hw->eeprom.page_size - 1); | |
268 | u16 pg_len = hw->eeprom.page_size - pg_off; | |
269 | if (pg_len > len) | |
270 | pg_len = len; | |
271 | ||
272 | /* Now dump the page */ | |
273 | if (e1000_spi_eeprom_read_page(hw, data, off, pg_len, intr)) | |
274 | return -1; | |
275 | ||
276 | /* Otherwise go on to the next page */ | |
277 | len -= pg_len; | |
278 | off += pg_len; | |
279 | data += pg_len; | |
280 | } | |
281 | ||
282 | /* We're done! */ | |
283 | return 0; | |
284 | } | |
285 | ||
286 | static int e1000_spi_eeprom_program(struct e1000_hw *hw, | |
472d5460 | 287 | const void *data, u16 off, u16 len, bool intr) |
ce5207e1 KM |
288 | { |
289 | /* Program each page in sequence */ | |
290 | while (len) { | |
291 | /* Calculate the data bytes on this page */ | |
292 | u16 pg_off = off & (hw->eeprom.page_size - 1); | |
293 | u16 pg_len = hw->eeprom.page_size - pg_off; | |
294 | if (pg_len > len) | |
295 | pg_len = len; | |
296 | ||
297 | /* Interruptibly wait for the EEPROM to be ready */ | |
298 | if (e1000_spi_eeprom_poll_ready(hw, intr)) | |
299 | return -1; | |
300 | ||
301 | /* Enable write access */ | |
302 | if (e1000_spi_eeprom_enable_wr(hw, intr)) | |
303 | return -1; | |
304 | ||
305 | /* Now program the page */ | |
306 | if (e1000_spi_eeprom_write_page(hw, data, off, pg_len, intr)) | |
307 | return -1; | |
308 | ||
309 | /* Otherwise go on to the next page */ | |
310 | len -= pg_len; | |
311 | off += pg_len; | |
312 | data += pg_len; | |
313 | } | |
314 | ||
315 | /* Wait for the last write to complete */ | |
316 | if (e1000_spi_eeprom_poll_ready(hw, intr)) | |
317 | return -1; | |
318 | ||
319 | /* We're done! */ | |
320 | return 0; | |
321 | } | |
322 | ||
323 | static int do_e1000_spi_show(cmd_tbl_t *cmdtp, struct e1000_hw *hw, | |
324 | int argc, char * const argv[]) | |
325 | { | |
326 | unsigned int length = 0; | |
327 | u16 i, offset = 0; | |
328 | u8 *buffer; | |
329 | int err; | |
330 | ||
331 | if (argc > 2) { | |
332 | cmd_usage(cmdtp); | |
333 | return 1; | |
334 | } | |
335 | ||
336 | /* Parse the offset and length */ | |
337 | if (argc >= 1) | |
338 | offset = simple_strtoul(argv[0], NULL, 0); | |
339 | if (argc == 2) | |
340 | length = simple_strtoul(argv[1], NULL, 0); | |
341 | else if (offset < (hw->eeprom.word_size << 1)) | |
342 | length = (hw->eeprom.word_size << 1) - offset; | |
343 | ||
344 | /* Extra sanity checks */ | |
345 | if (!length) { | |
346 | E1000_ERR(hw->nic, "Requested zero-sized dump!\n"); | |
347 | return 1; | |
348 | } | |
349 | if ((0x10000 < length) || (0x10000 - length < offset)) { | |
350 | E1000_ERR(hw->nic, "Can't dump past 0xFFFF!\n"); | |
351 | return 1; | |
352 | } | |
353 | ||
354 | /* Allocate a buffer to hold stuff */ | |
355 | buffer = malloc(length); | |
356 | if (!buffer) { | |
357 | E1000_ERR(hw->nic, "Out of Memory!\n"); | |
358 | return 1; | |
359 | } | |
360 | ||
361 | /* Acquire the EEPROM and perform the dump */ | |
362 | if (e1000_acquire_eeprom(hw)) { | |
363 | E1000_ERR(hw->nic, "EEPROM SPI cannot be acquired!\n"); | |
364 | free(buffer); | |
365 | return 1; | |
366 | } | |
472d5460 | 367 | err = e1000_spi_eeprom_dump(hw, buffer, offset, length, true); |
ce5207e1 KM |
368 | e1000_release_eeprom(hw); |
369 | if (err) { | |
370 | E1000_ERR(hw->nic, "Interrupted!\n"); | |
371 | free(buffer); | |
372 | return 1; | |
373 | } | |
374 | ||
375 | /* Now hexdump the result */ | |
376 | printf("%s: ===== Intel e1000 EEPROM (0x%04hX - 0x%04hX) =====", | |
377 | hw->nic->name, offset, offset + length - 1); | |
378 | for (i = 0; i < length; i++) { | |
379 | if ((i & 0xF) == 0) | |
380 | printf("\n%s: %04hX: ", hw->nic->name, offset + i); | |
381 | else if ((i & 0xF) == 0x8) | |
382 | printf(" "); | |
383 | printf(" %02hx", buffer[i]); | |
384 | } | |
385 | printf("\n"); | |
386 | ||
387 | /* Success! */ | |
388 | free(buffer); | |
389 | return 0; | |
390 | } | |
391 | ||
392 | static int do_e1000_spi_dump(cmd_tbl_t *cmdtp, struct e1000_hw *hw, | |
393 | int argc, char * const argv[]) | |
394 | { | |
395 | unsigned int length; | |
396 | u16 offset; | |
397 | void *dest; | |
398 | ||
399 | if (argc != 3) { | |
400 | cmd_usage(cmdtp); | |
401 | return 1; | |
402 | } | |
403 | ||
404 | /* Parse the arguments */ | |
405 | dest = (void *)simple_strtoul(argv[0], NULL, 16); | |
406 | offset = simple_strtoul(argv[1], NULL, 0); | |
407 | length = simple_strtoul(argv[2], NULL, 0); | |
408 | ||
409 | /* Extra sanity checks */ | |
410 | if (!length) { | |
411 | E1000_ERR(hw->nic, "Requested zero-sized dump!\n"); | |
412 | return 1; | |
413 | } | |
414 | if ((0x10000 < length) || (0x10000 - length < offset)) { | |
415 | E1000_ERR(hw->nic, "Can't dump past 0xFFFF!\n"); | |
416 | return 1; | |
417 | } | |
418 | ||
419 | /* Acquire the EEPROM */ | |
420 | if (e1000_acquire_eeprom(hw)) { | |
421 | E1000_ERR(hw->nic, "EEPROM SPI cannot be acquired!\n"); | |
422 | return 1; | |
423 | } | |
424 | ||
425 | /* Perform the programming operation */ | |
472d5460 | 426 | if (e1000_spi_eeprom_dump(hw, dest, offset, length, true) < 0) { |
ce5207e1 KM |
427 | E1000_ERR(hw->nic, "Interrupted!\n"); |
428 | e1000_release_eeprom(hw); | |
429 | return 1; | |
430 | } | |
431 | ||
432 | e1000_release_eeprom(hw); | |
433 | printf("%s: ===== EEPROM DUMP COMPLETE =====\n", hw->nic->name); | |
434 | return 0; | |
435 | } | |
436 | ||
437 | static int do_e1000_spi_program(cmd_tbl_t *cmdtp, struct e1000_hw *hw, | |
438 | int argc, char * const argv[]) | |
439 | { | |
440 | unsigned int length; | |
441 | const void *source; | |
442 | u16 offset; | |
443 | ||
444 | if (argc != 3) { | |
445 | cmd_usage(cmdtp); | |
446 | return 1; | |
447 | } | |
448 | ||
449 | /* Parse the arguments */ | |
450 | source = (const void *)simple_strtoul(argv[0], NULL, 16); | |
451 | offset = simple_strtoul(argv[1], NULL, 0); | |
452 | length = simple_strtoul(argv[2], NULL, 0); | |
453 | ||
454 | /* Acquire the EEPROM */ | |
455 | if (e1000_acquire_eeprom(hw)) { | |
456 | E1000_ERR(hw->nic, "EEPROM SPI cannot be acquired!\n"); | |
457 | return 1; | |
458 | } | |
459 | ||
460 | /* Perform the programming operation */ | |
472d5460 | 461 | if (e1000_spi_eeprom_program(hw, source, offset, length, true) < 0) { |
ce5207e1 KM |
462 | E1000_ERR(hw->nic, "Interrupted!\n"); |
463 | e1000_release_eeprom(hw); | |
464 | return 1; | |
465 | } | |
466 | ||
467 | e1000_release_eeprom(hw); | |
468 | printf("%s: ===== EEPROM PROGRAMMED =====\n", hw->nic->name); | |
469 | return 0; | |
470 | } | |
471 | ||
472 | static int do_e1000_spi_checksum(cmd_tbl_t *cmdtp, struct e1000_hw *hw, | |
473 | int argc, char * const argv[]) | |
474 | { | |
deb7282f | 475 | uint16_t i, length, checksum = 0, checksum_reg; |
ce5207e1 | 476 | uint16_t *buffer; |
472d5460 | 477 | bool upd; |
ce5207e1 KM |
478 | |
479 | if (argc == 0) | |
480 | upd = 0; | |
481 | else if ((argc == 1) && !strcmp(argv[0], "update")) | |
482 | upd = 1; | |
483 | else { | |
484 | cmd_usage(cmdtp); | |
485 | return 1; | |
486 | } | |
487 | ||
488 | /* Allocate a temporary buffer */ | |
489 | length = sizeof(uint16_t) * (EEPROM_CHECKSUM_REG + 1); | |
490 | buffer = malloc(length); | |
491 | if (!buffer) { | |
492 | E1000_ERR(hw->nic, "Unable to allocate EEPROM buffer!\n"); | |
493 | return 1; | |
494 | } | |
495 | ||
496 | /* Acquire the EEPROM */ | |
497 | if (e1000_acquire_eeprom(hw)) { | |
498 | E1000_ERR(hw->nic, "EEPROM SPI cannot be acquired!\n"); | |
499 | return 1; | |
500 | } | |
501 | ||
502 | /* Read the EEPROM */ | |
472d5460 | 503 | if (e1000_spi_eeprom_dump(hw, buffer, 0, length, true) < 0) { |
ce5207e1 KM |
504 | E1000_ERR(hw->nic, "Interrupted!\n"); |
505 | e1000_release_eeprom(hw); | |
506 | return 1; | |
507 | } | |
508 | ||
509 | /* Compute the checksum and read the expected value */ | |
510 | for (i = 0; i < EEPROM_CHECKSUM_REG; i++) | |
511 | checksum += le16_to_cpu(buffer[i]); | |
512 | checksum = ((uint16_t)EEPROM_SUM) - checksum; | |
513 | checksum_reg = le16_to_cpu(buffer[i]); | |
514 | ||
515 | /* Verify it! */ | |
516 | if (checksum_reg == checksum) { | |
517 | printf("%s: INFO: EEPROM checksum is correct! (0x%04hx)\n", | |
518 | hw->nic->name, checksum); | |
519 | e1000_release_eeprom(hw); | |
520 | return 0; | |
521 | } | |
522 | ||
523 | /* Hrm, verification failed, print an error */ | |
524 | E1000_ERR(hw->nic, "EEPROM checksum is incorrect!\n"); | |
525 | E1000_ERR(hw->nic, " ...register was 0x%04hx, calculated 0x%04hx\n", | |
526 | checksum_reg, checksum); | |
527 | ||
528 | /* If they didn't ask us to update it, just return an error */ | |
529 | if (!upd) { | |
530 | e1000_release_eeprom(hw); | |
531 | return 1; | |
532 | } | |
533 | ||
534 | /* Ok, correct it! */ | |
535 | printf("%s: Reprogramming the EEPROM checksum...\n", hw->nic->name); | |
536 | buffer[i] = cpu_to_le16(checksum); | |
537 | if (e1000_spi_eeprom_program(hw, &buffer[i], i * sizeof(uint16_t), | |
472d5460 | 538 | sizeof(uint16_t), true)) { |
ce5207e1 KM |
539 | E1000_ERR(hw->nic, "Interrupted!\n"); |
540 | e1000_release_eeprom(hw); | |
541 | return 1; | |
542 | } | |
543 | ||
544 | e1000_release_eeprom(hw); | |
545 | return 0; | |
546 | } | |
547 | ||
548 | int do_e1000_spi(cmd_tbl_t *cmdtp, struct e1000_hw *hw, | |
549 | int argc, char * const argv[]) | |
550 | { | |
551 | if (argc < 1) { | |
552 | cmd_usage(cmdtp); | |
553 | return 1; | |
554 | } | |
555 | ||
556 | /* Make sure it has an SPI chip */ | |
557 | if (hw->eeprom.type != e1000_eeprom_spi) { | |
558 | E1000_ERR(hw->nic, "No attached SPI EEPROM found!\n"); | |
559 | return 1; | |
560 | } | |
561 | ||
562 | /* Check the eeprom sub-sub-command arguments */ | |
563 | if (!strcmp(argv[0], "show")) | |
564 | return do_e1000_spi_show(cmdtp, hw, argc - 1, argv + 1); | |
565 | ||
566 | if (!strcmp(argv[0], "dump")) | |
567 | return do_e1000_spi_dump(cmdtp, hw, argc - 1, argv + 1); | |
568 | ||
569 | if (!strcmp(argv[0], "program")) | |
570 | return do_e1000_spi_program(cmdtp, hw, argc - 1, argv + 1); | |
571 | ||
572 | if (!strcmp(argv[0], "checksum")) | |
573 | return do_e1000_spi_checksum(cmdtp, hw, argc - 1, argv + 1); | |
574 | ||
575 | cmd_usage(cmdtp); | |
576 | return 1; | |
577 | } | |
578 | ||
579 | #endif /* not CONFIG_CMD_E1000 */ |