]>
Commit | Line | Data |
---|---|---|
6fc6879b JM |
1 | ##### hostapd configuration file ############################################## |
2 | # Empty lines and lines starting with # are ignored | |
3 | ||
4 | # AP netdevice name (without 'ap' postfix, i.e., wlan0 uses wlan0ap for | |
01b32d5e | 5 | # management frames with the Host AP driver); wlan0 with many nl80211 drivers |
31d3692f TK |
6 | # Note: This attribute can be overridden by the values supplied with the '-i' |
7 | # command line parameter. | |
6fc6879b JM |
8 | interface=wlan0 |
9 | ||
01b32d5e | 10 | # In case of atheros and nl80211 driver interfaces, an additional |
94627f6c JM |
11 | # configuration parameter, bridge, may be used to notify hostapd if the |
12 | # interface is included in a bridge. This parameter is not used with Host AP | |
13 | # driver. If the bridge parameter is not set, the drivers will automatically | |
14 | # figure out the bridge interface (assuming sysfs is enabled and mounted to | |
15 | # /sys) and this parameter may not be needed. | |
16 | # | |
17 | # For nl80211, this parameter can be used to request the AP interface to be | |
18 | # added to the bridge automatically (brctl may refuse to do this before hostapd | |
19 | # has been started to change the interface mode). If needed, the bridge | |
20 | # interface is also created. | |
6fc6879b JM |
21 | #bridge=br0 |
22 | ||
ebd55728 | 23 | # Driver interface type (hostap/wired/none/nl80211/bsd); |
e6f9861a | 24 | # default: hostap). nl80211 is used with all Linux mac80211 drivers. |
d64dabee | 25 | # Use driver=none if building hostapd as a standalone RADIUS server that does |
6fc6879b JM |
26 | # not control any wireless/wired driver. |
27 | # driver=hostap | |
28 | ||
0ecff8d7 JM |
29 | # Driver interface parameters (mainly for development testing use) |
30 | # driver_params=<params> | |
31 | ||
6fc6879b JM |
32 | # hostapd event logger configuration |
33 | # | |
34 | # Two output method: syslog and stdout (only usable if not forking to | |
35 | # background). | |
36 | # | |
37 | # Module bitfield (ORed bitfield of modules that will be logged; -1 = all | |
38 | # modules): | |
39 | # bit 0 (1) = IEEE 802.11 | |
40 | # bit 1 (2) = IEEE 802.1X | |
41 | # bit 2 (4) = RADIUS | |
42 | # bit 3 (8) = WPA | |
43 | # bit 4 (16) = driver interface | |
44 | # bit 5 (32) = IAPP | |
45 | # bit 6 (64) = MLME | |
46 | # | |
47 | # Levels (minimum value for logged events): | |
48 | # 0 = verbose debugging | |
49 | # 1 = debugging | |
50 | # 2 = informational messages | |
51 | # 3 = notification | |
52 | # 4 = warning | |
53 | # | |
54 | logger_syslog=-1 | |
55 | logger_syslog_level=2 | |
56 | logger_stdout=-1 | |
57 | logger_stdout_level=2 | |
58 | ||
6fc6879b JM |
59 | # Interface for separate control program. If this is specified, hostapd |
60 | # will create this directory and a UNIX domain socket for listening to requests | |
61 | # from external programs (CLI/GUI, etc.) for status information and | |
62 | # configuration. The socket file will be named based on the interface name, so | |
63 | # multiple hostapd processes/interfaces can be run at the same time if more | |
64 | # than one interface is used. | |
65 | # /var/run/hostapd is the recommended directory for sockets and by default, | |
66 | # hostapd_cli will use it when trying to connect with hostapd. | |
67 | ctrl_interface=/var/run/hostapd | |
68 | ||
69 | # Access control for the control interface can be configured by setting the | |
70 | # directory to allow only members of a group to use sockets. This way, it is | |
71 | # possible to run hostapd as root (since it needs to change network | |
72 | # configuration and open raw sockets) and still allow GUI/CLI components to be | |
73 | # run as non-root users. However, since the control interface can be used to | |
74 | # change the network configuration, this access needs to be protected in many | |
75 | # cases. By default, hostapd is configured to use gid 0 (root). If you | |
76 | # want to allow non-root users to use the contron interface, add a new group | |
77 | # and change this value to match with that group. Add users that should have | |
78 | # control interface access to this group. | |
79 | # | |
80 | # This variable can be a group name or gid. | |
81 | #ctrl_interface_group=wheel | |
82 | ctrl_interface_group=0 | |
83 | ||
84 | ||
85 | ##### IEEE 802.11 related configuration ####################################### | |
86 | ||
87 | # SSID to be used in IEEE 802.11 management frames | |
88 | ssid=test | |
e122bb70 JM |
89 | # Alternative formats for configuring SSID |
90 | # (double quoted string, hexdump, printf-escaped string) | |
91 | #ssid2="test" | |
92 | #ssid2=74657374 | |
93 | #ssid2=P"hello\nthere" | |
6fc6879b | 94 | |
b93c8509 JM |
95 | # UTF-8 SSID: Whether the SSID is to be interpreted using UTF-8 encoding |
96 | #utf8_ssid=1 | |
97 | ||
6f4071c0 JM |
98 | # Country code (ISO/IEC 3166-1). Used to set regulatory domain. |
99 | # Set as needed to indicate country in which device is operating. | |
6fc6879b | 100 | # This can limit available channels and transmit power. |
6fc6879b JM |
101 | #country_code=US |
102 | ||
103 | # Enable IEEE 802.11d. This advertises the country_code and the set of allowed | |
104 | # channels and transmit power levels based on the regulatory limits. The | |
105 | # country_code setting must be configured with the correct country for | |
106 | # IEEE 802.11d functions. | |
107 | # (default: 0 = disabled) | |
108 | #ieee80211d=1 | |
109 | ||
b113a171 SW |
110 | # Enable IEEE 802.11h. This enables radar detection and DFS support if |
111 | # available. DFS support is required on outdoor 5 GHz channels in most countries | |
112 | # of the world. This can be used only with ieee80211d=1. | |
113 | # (default: 0 = disabled) | |
114 | #ieee80211h=1 | |
115 | ||
e0392f82 S |
116 | # Add Power Constraint element to Beacon and Probe Response frames |
117 | # This config option adds Power Constraint element when applicable and Country | |
118 | # element is added. Power Constraint element is required by Transmit Power | |
119 | # Control. This can be used only with ieee80211d=1. | |
120 | # Valid values are 0..255. | |
121 | #local_pwr_constraint=3 | |
122 | ||
3d7ad2f6 C |
123 | # Set Spectrum Management subfield in the Capability Information field. |
124 | # This config option forces the Spectrum Management bit to be set. When this | |
125 | # option is not set, the value of the Spectrum Management bit depends on whether | |
126 | # DFS or TPC is required by regulatory authorities. This can be used only with | |
127 | # ieee80211d=1 and local_pwr_constraint configured. | |
128 | #spectrum_mgmt_required=1 | |
129 | ||
2da4a56f JM |
130 | # Operation mode (a = IEEE 802.11a (5 GHz), b = IEEE 802.11b (2.4 GHz), |
131 | # g = IEEE 802.11g (2.4 GHz), ad = IEEE 802.11ad (60 GHz); a/g options are used | |
132 | # with IEEE 802.11n (HT), too, to specify band). For IEEE 802.11ac (VHT), this | |
133 | # needs to be set to hw_mode=a. When using ACS (see channel parameter), a | |
134 | # special value "any" can be used to indicate that any support band can be used. | |
135 | # This special case is currently supported only with drivers with which | |
136 | # offloaded ACS is used. | |
6fc6879b | 137 | # Default: IEEE 802.11b |
d0df54ca | 138 | hw_mode=g |
6fc6879b JM |
139 | |
140 | # Channel number (IEEE 802.11) | |
27e120c4 | 141 | # (default: 0, i.e., not set) |
e783c9b0 PR |
142 | # Please note that some drivers do not use this value from hostapd and the |
143 | # channel will need to be configured separately with iwconfig. | |
50f4f2a0 MK |
144 | # |
145 | # If CONFIG_ACS build option is enabled, the channel can be selected | |
146 | # automatically at run time by setting channel=acs_survey or channel=0, both of | |
147 | # which will enable the ACS survey based algorithm. | |
d0df54ca | 148 | channel=1 |
6fc6879b | 149 | |
50f4f2a0 MK |
150 | # ACS tuning - Automatic Channel Selection |
151 | # See: http://wireless.kernel.org/en/users/Documentation/acs | |
152 | # | |
153 | # You can customize the ACS survey algorithm with following variables: | |
154 | # | |
155 | # acs_num_scans requirement is 1..100 - number of scans to be performed that | |
156 | # are used to trigger survey data gathering of an underlying device driver. | |
157 | # Scans are passive and typically take a little over 100ms (depending on the | |
158 | # driver) on each available channel for given hw_mode. Increasing this value | |
159 | # means sacrificing startup time and gathering more data wrt channel | |
160 | # interference that may help choosing a better channel. This can also help fine | |
161 | # tune the ACS scan time in case a driver has different scan dwell times. | |
162 | # | |
68fa00c3 JM |
163 | # acs_chan_bias is a space-separated list of <channel>:<bias> pairs. It can be |
164 | # used to increase (or decrease) the likelihood of a specific channel to be | |
165 | # selected by the ACS algorithm. The total interference factor for each channel | |
166 | # gets multiplied by the specified bias value before finding the channel with | |
167 | # the lowest value. In other words, values between 0.0 and 1.0 can be used to | |
168 | # make a channel more likely to be picked while values larger than 1.0 make the | |
169 | # specified channel less likely to be picked. This can be used, e.g., to prefer | |
170 | # the commonly used 2.4 GHz band channels 1, 6, and 11 (which is the default | |
171 | # behavior on 2.4 GHz band if no acs_chan_bias parameter is specified). | |
172 | # | |
50f4f2a0 MK |
173 | # Defaults: |
174 | #acs_num_scans=5 | |
68fa00c3 | 175 | #acs_chan_bias=1:0.8 6:0.8 11:0.8 |
50f4f2a0 | 176 | |
70ee1be2 | 177 | # Channel list restriction. This option allows hostapd to select one of the |
1648cc64 | 178 | # provided channels when a channel should be automatically selected. |
857d9422 | 179 | # Channel list can be provided as range using hyphen ('-') or individual |
234a17cc | 180 | # channels can be specified by space (' ') separated values |
857d9422 | 181 | # Default: all channels allowed in selected hw_mode |
70ee1be2 | 182 | #chanlist=100 104 108 112 116 |
857d9422 | 183 | #chanlist=1 6 11-13 |
70ee1be2 | 184 | |
6fc6879b JM |
185 | # Beacon interval in kus (1.024 ms) (default: 100; range 15..65535) |
186 | beacon_int=100 | |
187 | ||
ffbf1eaa | 188 | # DTIM (delivery traffic information message) period (range 1..255): |
6fc6879b JM |
189 | # number of beacons between DTIMs (1 = every beacon includes DTIM element) |
190 | # (default: 2) | |
191 | dtim_period=2 | |
192 | ||
193 | # Maximum number of stations allowed in station table. New stations will be | |
194 | # rejected after the station table is full. IEEE 802.11 has a limit of 2007 | |
195 | # different association IDs, so this number should not be larger than that. | |
196 | # (default: 2007) | |
197 | max_num_sta=255 | |
198 | ||
bc50bb0a | 199 | # RTS/CTS threshold; -1 = disabled (default); range -1..65535 |
6fc6879b JM |
200 | # If this field is not included in hostapd.conf, hostapd will not control |
201 | # RTS threshold and 'iwconfig wlan# rts <val>' can be used to set it. | |
bc50bb0a | 202 | rts_threshold=-1 |
6fc6879b | 203 | |
95be79f1 | 204 | # Fragmentation threshold; -1 = disabled (default); range -1, 256..2346 |
6fc6879b JM |
205 | # If this field is not included in hostapd.conf, hostapd will not control |
206 | # fragmentation threshold and 'iwconfig wlan# frag <val>' can be used to set | |
207 | # it. | |
95be79f1 | 208 | fragm_threshold=-1 |
6fc6879b JM |
209 | |
210 | # Rate configuration | |
211 | # Default is to enable all rates supported by the hardware. This configuration | |
212 | # item allows this list be filtered so that only the listed rates will be left | |
213 | # in the list. If the list is empty, all rates are used. This list can have | |
214 | # entries that are not in the list of rates the hardware supports (such entries | |
215 | # are ignored). The entries in this list are in 100 kbps, i.e., 11 Mbps = 110. | |
216 | # If this item is present, at least one rate have to be matching with the rates | |
217 | # hardware supports. | |
218 | # default: use the most common supported rate setting for the selected | |
219 | # hw_mode (i.e., this line can be removed from configuration file in most | |
220 | # cases) | |
221 | #supported_rates=10 20 55 110 60 90 120 180 240 360 480 540 | |
222 | ||
223 | # Basic rate set configuration | |
224 | # List of rates (in 100 kbps) that are included in the basic rate set. | |
225 | # If this item is not included, usually reasonable default set is used. | |
226 | #basic_rates=10 20 | |
227 | #basic_rates=10 20 55 110 | |
228 | #basic_rates=60 120 240 | |
229 | ||
839faf04 JM |
230 | # Short Preamble |
231 | # This parameter can be used to enable optional use of short preamble for | |
232 | # frames sent at 2 Mbps, 5.5 Mbps, and 11 Mbps to improve network performance. | |
233 | # This applies only to IEEE 802.11b-compatible networks and this should only be | |
234 | # enabled if the local hardware supports use of short preamble. If any of the | |
235 | # associated STAs do not support short preamble, use of short preamble will be | |
236 | # disabled (and enabled when such STAs disassociate) dynamically. | |
237 | # 0 = do not allow use of short preamble (default) | |
238 | # 1 = allow use of short preamble | |
239 | #preamble=1 | |
240 | ||
6fc6879b JM |
241 | # Station MAC address -based authentication |
242 | # Please note that this kind of access control requires a driver that uses | |
243 | # hostapd to take care of management frame processing and as such, this can be | |
01b32d5e | 244 | # used with driver=hostap or driver=nl80211, but not with driver=atheros. |
6fc6879b JM |
245 | # 0 = accept unless in deny list |
246 | # 1 = deny unless in accept list | |
247 | # 2 = use external RADIUS server (accept/deny lists are searched first) | |
248 | macaddr_acl=0 | |
249 | ||
250 | # Accept/deny lists are read from separate files (containing list of | |
251 | # MAC addresses, one per line). Use absolute path name to make sure that the | |
252 | # files can be read on SIGHUP configuration reloads. | |
253 | #accept_mac_file=/etc/hostapd.accept | |
254 | #deny_mac_file=/etc/hostapd.deny | |
255 | ||
256 | # IEEE 802.11 specifies two authentication algorithms. hostapd can be | |
257 | # configured to allow both of these or only one. Open system authentication | |
258 | # should be used with IEEE 802.1X. | |
259 | # Bit fields of allowed authentication algorithms: | |
260 | # bit 0 = Open System Authentication | |
261 | # bit 1 = Shared Key Authentication (requires WEP) | |
262 | auth_algs=3 | |
263 | ||
264 | # Send empty SSID in beacons and ignore probe request frames that do not | |
265 | # specify full SSID, i.e., require stations to know SSID. | |
266 | # default: disabled (0) | |
267 | # 1 = send empty (length=0) SSID in beacon and ignore probe request for | |
268 | # broadcast SSID | |
269 | # 2 = clear SSID (ASCII 0), but keep the original length (this may be required | |
270 | # with some clients that do not support empty SSID) and ignore probe | |
271 | # requests for broadcast SSID | |
272 | ignore_broadcast_ssid=0 | |
273 | ||
9b7a1bd7 JM |
274 | # Do not reply to broadcast Probe Request frames from unassociated STA if there |
275 | # is no room for additional stations (max_num_sta). This can be used to | |
276 | # discourage a STA from trying to associate with this AP if the association | |
277 | # would be rejected due to maximum STA limit. | |
278 | # Default: 0 (disabled) | |
279 | #no_probe_resp_if_max_sta=0 | |
280 | ||
234a17cc | 281 | # Additional vendor specific elements for Beacon and Probe Response frames |
b52f084c JM |
282 | # This parameter can be used to add additional vendor specific element(s) into |
283 | # the end of the Beacon and Probe Response frames. The format for these | |
284 | # element(s) is a hexdump of the raw information elements (id+len+payload for | |
285 | # one or more elements) | |
286 | #vendor_elements=dd0411223301 | |
287 | ||
a9112270 BKB |
288 | # Additional vendor specific elements for (Re)Association Response frames |
289 | # This parameter can be used to add additional vendor specific element(s) into | |
290 | # the end of the (Re)Association Response frames. The format for these | |
291 | # element(s) is a hexdump of the raw information elements (id+len+payload for | |
292 | # one or more elements) | |
293 | #assocresp_elements=dd0411223301 | |
294 | ||
6fc6879b | 295 | # TX queue parameters (EDCF / bursting) |
6fc6879b JM |
296 | # tx_queue_<queue name>_<param> |
297 | # queues: data0, data1, data2, data3, after_beacon, beacon | |
298 | # (data0 is the highest priority queue) | |
299 | # parameters: | |
300 | # aifs: AIFS (default 2) | |
6c731491 JM |
301 | # cwmin: cwMin (1, 3, 7, 15, 31, 63, 127, 255, 511, 1023, 2047, 4095, 8191, |
302 | # 16383, 32767) | |
303 | # cwmax: cwMax (same values as cwMin, cwMax >= cwMin) | |
6fc6879b JM |
304 | # burst: maximum length (in milliseconds with precision of up to 0.1 ms) for |
305 | # bursting | |
306 | # | |
307 | # Default WMM parameters (IEEE 802.11 draft; 11-03-0504-03-000e): | |
308 | # These parameters are used by the access point when transmitting frames | |
309 | # to the clients. | |
310 | # | |
311 | # Low priority / AC_BK = background | |
312 | #tx_queue_data3_aifs=7 | |
313 | #tx_queue_data3_cwmin=15 | |
314 | #tx_queue_data3_cwmax=1023 | |
315 | #tx_queue_data3_burst=0 | |
316 | # Note: for IEEE 802.11b mode: cWmin=31 cWmax=1023 burst=0 | |
317 | # | |
318 | # Normal priority / AC_BE = best effort | |
319 | #tx_queue_data2_aifs=3 | |
320 | #tx_queue_data2_cwmin=15 | |
321 | #tx_queue_data2_cwmax=63 | |
322 | #tx_queue_data2_burst=0 | |
323 | # Note: for IEEE 802.11b mode: cWmin=31 cWmax=127 burst=0 | |
324 | # | |
325 | # High priority / AC_VI = video | |
326 | #tx_queue_data1_aifs=1 | |
327 | #tx_queue_data1_cwmin=7 | |
328 | #tx_queue_data1_cwmax=15 | |
329 | #tx_queue_data1_burst=3.0 | |
330 | # Note: for IEEE 802.11b mode: cWmin=15 cWmax=31 burst=6.0 | |
331 | # | |
332 | # Highest priority / AC_VO = voice | |
333 | #tx_queue_data0_aifs=1 | |
334 | #tx_queue_data0_cwmin=3 | |
335 | #tx_queue_data0_cwmax=7 | |
336 | #tx_queue_data0_burst=1.5 | |
337 | # Note: for IEEE 802.11b mode: cWmin=7 cWmax=15 burst=3.3 | |
6fc6879b | 338 | |
d85825e3 | 339 | # 802.1D Tag (= UP) to AC mappings |
6fc6879b JM |
340 | # WMM specifies following mapping of data frames to different ACs. This mapping |
341 | # can be configured using Linux QoS/tc and sch_pktpri.o module. | |
342 | # 802.1D Tag 802.1D Designation Access Category WMM Designation | |
343 | # 1 BK AC_BK Background | |
344 | # 2 - AC_BK Background | |
345 | # 0 BE AC_BE Best Effort | |
d85825e3 | 346 | # 3 EE AC_BE Best Effort |
6fc6879b JM |
347 | # 4 CL AC_VI Video |
348 | # 5 VI AC_VI Video | |
349 | # 6 VO AC_VO Voice | |
350 | # 7 NC AC_VO Voice | |
351 | # Data frames with no priority information: AC_BE | |
352 | # Management frames: AC_VO | |
353 | # PS-Poll frames: AC_BE | |
354 | ||
355 | # Default WMM parameters (IEEE 802.11 draft; 11-03-0504-03-000e): | |
356 | # for 802.11a or 802.11g networks | |
357 | # These parameters are sent to WMM clients when they associate. | |
358 | # The parameters will be used by WMM clients for frames transmitted to the | |
359 | # access point. | |
360 | # | |
361 | # note - txop_limit is in units of 32microseconds | |
362 | # note - acm is admission control mandatory flag. 0 = admission control not | |
363 | # required, 1 = mandatory | |
6c731491 JM |
364 | # note - Here cwMin and cmMax are in exponent form. The actual cw value used |
365 | # will be (2^n)-1 where n is the value given here. The allowed range for these | |
366 | # wmm_ac_??_{cwmin,cwmax} is 0..15 with cwmax >= cwmin. | |
6fc6879b | 367 | # |
3ae0800c | 368 | wmm_enabled=1 |
6fc6879b | 369 | # |
721abef9 YAP |
370 | # WMM-PS Unscheduled Automatic Power Save Delivery [U-APSD] |
371 | # Enable this flag if U-APSD supported outside hostapd (eg., Firmware/driver) | |
372 | #uapsd_advertisement_enabled=1 | |
373 | # | |
6fc6879b | 374 | # Low priority / AC_BK = background |
3ae0800c JM |
375 | wmm_ac_bk_cwmin=4 |
376 | wmm_ac_bk_cwmax=10 | |
377 | wmm_ac_bk_aifs=7 | |
378 | wmm_ac_bk_txop_limit=0 | |
379 | wmm_ac_bk_acm=0 | |
6fc6879b JM |
380 | # Note: for IEEE 802.11b mode: cWmin=5 cWmax=10 |
381 | # | |
382 | # Normal priority / AC_BE = best effort | |
3ae0800c JM |
383 | wmm_ac_be_aifs=3 |
384 | wmm_ac_be_cwmin=4 | |
385 | wmm_ac_be_cwmax=10 | |
386 | wmm_ac_be_txop_limit=0 | |
387 | wmm_ac_be_acm=0 | |
6fc6879b JM |
388 | # Note: for IEEE 802.11b mode: cWmin=5 cWmax=7 |
389 | # | |
390 | # High priority / AC_VI = video | |
3ae0800c JM |
391 | wmm_ac_vi_aifs=2 |
392 | wmm_ac_vi_cwmin=3 | |
393 | wmm_ac_vi_cwmax=4 | |
394 | wmm_ac_vi_txop_limit=94 | |
395 | wmm_ac_vi_acm=0 | |
6fc6879b JM |
396 | # Note: for IEEE 802.11b mode: cWmin=4 cWmax=5 txop_limit=188 |
397 | # | |
398 | # Highest priority / AC_VO = voice | |
3ae0800c JM |
399 | wmm_ac_vo_aifs=2 |
400 | wmm_ac_vo_cwmin=2 | |
401 | wmm_ac_vo_cwmax=3 | |
402 | wmm_ac_vo_txop_limit=47 | |
403 | wmm_ac_vo_acm=0 | |
6fc6879b JM |
404 | # Note: for IEEE 802.11b mode: cWmin=3 cWmax=4 burst=102 |
405 | ||
6fc6879b JM |
406 | # Static WEP key configuration |
407 | # | |
408 | # The key number to use when transmitting. | |
409 | # It must be between 0 and 3, and the corresponding key must be set. | |
410 | # default: not set | |
411 | #wep_default_key=0 | |
412 | # The WEP keys to use. | |
413 | # A key may be a quoted string or unquoted hexadecimal digits. | |
414 | # The key length should be 5, 13, or 16 characters, or 10, 26, or 32 | |
415 | # digits, depending on whether 40-bit (64-bit), 104-bit (128-bit), or | |
416 | # 128-bit (152-bit) WEP is used. | |
417 | # Only the default key must be supplied; the others are optional. | |
418 | # default: not set | |
419 | #wep_key0=123456789a | |
420 | #wep_key1="vwxyz" | |
421 | #wep_key2=0102030405060708090a0b0c0d | |
422 | #wep_key3=".2.4.6.8.0.23" | |
423 | ||
424 | # Station inactivity limit | |
425 | # | |
426 | # If a station does not send anything in ap_max_inactivity seconds, an | |
427 | # empty data frame is sent to it in order to verify whether it is | |
428 | # still in range. If this frame is not ACKed, the station will be | |
429 | # disassociated and then deauthenticated. This feature is used to | |
430 | # clear station table of old entries when the STAs move out of the | |
431 | # range. | |
432 | # | |
433 | # The station can associate again with the AP if it is still in range; | |
434 | # this inactivity poll is just used as a nicer way of verifying | |
435 | # inactivity; i.e., client will not report broken connection because | |
436 | # disassociation frame is not sent immediately without first polling | |
437 | # the STA with a data frame. | |
438 | # default: 300 (i.e., 5 minutes) | |
439 | #ap_max_inactivity=300 | |
ef01fa7b YAP |
440 | # |
441 | # The inactivity polling can be disabled to disconnect stations based on | |
442 | # inactivity timeout so that idle stations are more likely to be disconnected | |
443 | # even if they are still in range of the AP. This can be done by setting | |
444 | # skip_inactivity_poll to 1 (default 0). | |
445 | #skip_inactivity_poll=0 | |
6fc6879b | 446 | |
0d7e5a3a JB |
447 | # Disassociate stations based on excessive transmission failures or other |
448 | # indications of connection loss. This depends on the driver capabilities and | |
449 | # may not be available with all drivers. | |
450 | #disassoc_low_ack=1 | |
451 | ||
b0194fe0 JM |
452 | # Maximum allowed Listen Interval (how many Beacon periods STAs are allowed to |
453 | # remain asleep). Default: 65535 (no limit apart from field size) | |
454 | #max_listen_interval=100 | |
6fc6879b | 455 | |
fbbfcbac FF |
456 | # WDS (4-address frame) mode with per-station virtual interfaces |
457 | # (only supported with driver=nl80211) | |
458 | # This mode allows associated stations to use 4-address frames to allow layer 2 | |
459 | # bridging to be used. | |
460 | #wds_sta=1 | |
461 | ||
d38ae2ea FF |
462 | # If bridge parameter is set, the WDS STA interface will be added to the same |
463 | # bridge by default. This can be overridden with the wds_bridge parameter to | |
464 | # use a separate bridge. | |
465 | #wds_bridge=wds-br0 | |
466 | ||
3f9a8137 SM |
467 | # Start the AP with beaconing disabled by default. |
468 | #start_disabled=0 | |
469 | ||
d3b42869 FF |
470 | # Client isolation can be used to prevent low-level bridging of frames between |
471 | # associated stations in the BSS. By default, this bridging is allowed. | |
472 | #ap_isolate=1 | |
473 | ||
ec8f36af KP |
474 | # BSS Load update period (in BUs) |
475 | # This field is used to enable and configure adding a BSS Load element into | |
476 | # Beacon and Probe Response frames. | |
477 | #bss_load_update_period=50 | |
478 | ||
9bc33868 JM |
479 | # Fixed BSS Load value for testing purposes |
480 | # This field can be used to configure hostapd to add a fixed BSS Load element | |
481 | # into Beacon and Probe Response frames for testing purposes. The format is | |
482 | # <station count>:<channel utilization>:<available admission capacity> | |
483 | #bss_load_test=12:80:20000 | |
484 | ||
de9289c8 JM |
485 | ##### IEEE 802.11n related configuration ###################################### |
486 | ||
487 | # ieee80211n: Whether IEEE 802.11n (HT) is enabled | |
488 | # 0 = disabled (default) | |
489 | # 1 = enabled | |
3ae0800c | 490 | # Note: You will also need to enable WMM for full HT functionality. |
2da4a56f | 491 | # Note: hw_mode=g (2.4 GHz) and hw_mode=a (5 GHz) is used to specify the band. |
de9289c8 JM |
492 | #ieee80211n=1 |
493 | ||
fc14f567 JM |
494 | # ht_capab: HT capabilities (list of flags) |
495 | # LDPC coding capability: [LDPC] = supported | |
a8d8410e JM |
496 | # Supported channel width set: [HT40-] = both 20 MHz and 40 MHz with secondary |
497 | # channel below the primary channel; [HT40+] = both 20 MHz and 40 MHz | |
8b6b6d82 | 498 | # with secondary channel above the primary channel |
a8d8410e | 499 | # (20 MHz only if neither is set) |
b3e7a97d JM |
500 | # Note: There are limits on which channels can be used with HT40- and |
501 | # HT40+. Following table shows the channels that may be available for | |
502 | # HT40- and HT40+ use per IEEE 802.11n Annex J: | |
503 | # freq HT40- HT40+ | |
504 | # 2.4 GHz 5-13 1-7 (1-9 in Europe/Japan) | |
505 | # 5 GHz 40,48,56,64 36,44,52,60 | |
506 | # (depending on the location, not all of these channels may be available | |
507 | # for use) | |
5eb4e3d0 JM |
508 | # Please note that 40 MHz channels may switch their primary and secondary |
509 | # channels if needed or creation of 40 MHz channel maybe rejected based | |
510 | # on overlapping BSSes. These changes are done automatically when hostapd | |
511 | # is setting up the 40 MHz channel. | |
fc14f567 JM |
512 | # Spatial Multiplexing (SM) Power Save: [SMPS-STATIC] or [SMPS-DYNAMIC] |
513 | # (SMPS disabled if neither is set) | |
514 | # HT-greenfield: [GF] (disabled if not set) | |
515 | # Short GI for 20 MHz: [SHORT-GI-20] (disabled if not set) | |
516 | # Short GI for 40 MHz: [SHORT-GI-40] (disabled if not set) | |
517 | # Tx STBC: [TX-STBC] (disabled if not set) | |
518 | # Rx STBC: [RX-STBC1] (one spatial stream), [RX-STBC12] (one or two spatial | |
519 | # streams), or [RX-STBC123] (one, two, or three spatial streams); Rx STBC | |
520 | # disabled if none of these set | |
521 | # HT-delayed Block Ack: [DELAYED-BA] (disabled if not set) | |
522 | # Maximum A-MSDU length: [MAX-AMSDU-7935] for 7935 octets (3839 octets if not | |
523 | # set) | |
524 | # DSSS/CCK Mode in 40 MHz: [DSSS_CCK-40] = allowed (not allowed if not set) | |
b7a8d67f | 525 | # 40 MHz intolerant [40-INTOLERANT] (not advertised if not set) |
fc14f567 | 526 | # L-SIG TXOP protection support: [LSIG-TXOP-PROT] (disabled if not set) |
a8d8410e | 527 | #ht_capab=[HT40-][SHORT-GI-20][SHORT-GI-40] |
fc14f567 | 528 | |
29448243 JM |
529 | # Require stations to support HT PHY (reject association if they do not) |
530 | #require_ht=1 | |
531 | ||
c101bb9d PS |
532 | # If set non-zero, require stations to perform scans of overlapping |
533 | # channels to test for stations which would be affected by 40 MHz traffic. | |
d2ca6baa JM |
534 | # This parameter sets the interval in seconds between these scans. Setting this |
535 | # to non-zero allows 2.4 GHz band AP to move dynamically to a 40 MHz channel if | |
536 | # no co-existence issues with neighboring devices are found. | |
c101bb9d PS |
537 | #obss_interval=0 |
538 | ||
efe45d14 MP |
539 | ##### IEEE 802.11ac related configuration ##################################### |
540 | ||
541 | # ieee80211ac: Whether IEEE 802.11ac (VHT) is enabled | |
542 | # 0 = disabled (default) | |
543 | # 1 = enabled | |
544 | # Note: You will also need to enable WMM for full VHT functionality. | |
2da4a56f | 545 | # Note: hw_mode=a is used to specify that 5 GHz band is used with VHT. |
efe45d14 MP |
546 | #ieee80211ac=1 |
547 | ||
548 | # vht_capab: VHT capabilities (list of flags) | |
549 | # | |
550 | # vht_max_mpdu_len: [MAX-MPDU-7991] [MAX-MPDU-11454] | |
551 | # Indicates maximum MPDU length | |
552 | # 0 = 3895 octets (default) | |
553 | # 1 = 7991 octets | |
554 | # 2 = 11454 octets | |
555 | # 3 = reserved | |
556 | # | |
557 | # supported_chan_width: [VHT160] [VHT160-80PLUS80] | |
558 | # Indicates supported Channel widths | |
559 | # 0 = 160 MHz & 80+80 channel widths are not supported (default) | |
560 | # 1 = 160 MHz channel width is supported | |
561 | # 2 = 160 MHz & 80+80 channel widths are supported | |
562 | # 3 = reserved | |
563 | # | |
564 | # Rx LDPC coding capability: [RXLDPC] | |
565 | # Indicates support for receiving LDPC coded pkts | |
566 | # 0 = Not supported (default) | |
567 | # 1 = Supported | |
568 | # | |
569 | # Short GI for 80 MHz: [SHORT-GI-80] | |
570 | # Indicates short GI support for reception of packets transmitted with TXVECTOR | |
571 | # params format equal to VHT and CBW = 80Mhz | |
572 | # 0 = Not supported (default) | |
573 | # 1 = Supported | |
574 | # | |
575 | # Short GI for 160 MHz: [SHORT-GI-160] | |
576 | # Indicates short GI support for reception of packets transmitted with TXVECTOR | |
577 | # params format equal to VHT and CBW = 160Mhz | |
578 | # 0 = Not supported (default) | |
579 | # 1 = Supported | |
580 | # | |
581 | # Tx STBC: [TX-STBC-2BY1] | |
582 | # Indicates support for the transmission of at least 2x1 STBC | |
583 | # 0 = Not supported (default) | |
584 | # 1 = Supported | |
585 | # | |
586 | # Rx STBC: [RX-STBC-1] [RX-STBC-12] [RX-STBC-123] [RX-STBC-1234] | |
587 | # Indicates support for the reception of PPDUs using STBC | |
588 | # 0 = Not supported (default) | |
589 | # 1 = support of one spatial stream | |
590 | # 2 = support of one and two spatial streams | |
591 | # 3 = support of one, two and three spatial streams | |
592 | # 4 = support of one, two, three and four spatial streams | |
593 | # 5,6,7 = reserved | |
594 | # | |
595 | # SU Beamformer Capable: [SU-BEAMFORMER] | |
596 | # Indicates support for operation as a single user beamformer | |
597 | # 0 = Not supported (default) | |
598 | # 1 = Supported | |
599 | # | |
600 | # SU Beamformee Capable: [SU-BEAMFORMEE] | |
601 | # Indicates support for operation as a single user beamformee | |
602 | # 0 = Not supported (default) | |
603 | # 1 = Supported | |
604 | # | |
442ffc51 VN |
605 | # Compressed Steering Number of Beamformer Antennas Supported: |
606 | # [BF-ANTENNA-2] [BF-ANTENNA-3] [BF-ANTENNA-4] | |
efe45d14 MP |
607 | # Beamformee's capability indicating the maximum number of beamformer |
608 | # antennas the beamformee can support when sending compressed beamforming | |
609 | # feedback | |
610 | # If SU beamformer capable, set to maximum value minus 1 | |
611 | # else reserved (default) | |
612 | # | |
442ffc51 VN |
613 | # Number of Sounding Dimensions: |
614 | # [SOUNDING-DIMENSION-2] [SOUNDING-DIMENSION-3] [SOUNDING-DIMENSION-4] | |
179099e6 | 615 | # Beamformer's capability indicating the maximum value of the NUM_STS parameter |
efe45d14 MP |
616 | # in the TXVECTOR of a VHT NDP |
617 | # If SU beamformer capable, set to maximum value minus 1 | |
618 | # else reserved (default) | |
619 | # | |
620 | # MU Beamformer Capable: [MU-BEAMFORMER] | |
621 | # Indicates support for operation as an MU beamformer | |
622 | # 0 = Not supported or sent by Non-AP STA (default) | |
623 | # 1 = Supported | |
624 | # | |
efe45d14 MP |
625 | # VHT TXOP PS: [VHT-TXOP-PS] |
626 | # Indicates whether or not the AP supports VHT TXOP Power Save Mode | |
627 | # or whether or not the STA is in VHT TXOP Power Save mode | |
234a17cc | 628 | # 0 = VHT AP doesn't support VHT TXOP PS mode (OR) VHT STA not in VHT TXOP PS |
efe45d14 | 629 | # mode |
234a17cc | 630 | # 1 = VHT AP supports VHT TXOP PS mode (OR) VHT STA is in VHT TXOP power save |
efe45d14 MP |
631 | # mode |
632 | # | |
633 | # +HTC-VHT Capable: [HTC-VHT] | |
634 | # Indicates whether or not the STA supports receiving a VHT variant HT Control | |
635 | # field. | |
636 | # 0 = Not supported (default) | |
637 | # 1 = supported | |
638 | # | |
639 | # Maximum A-MPDU Length Exponent: [MAX-A-MPDU-LEN-EXP0]..[MAX-A-MPDU-LEN-EXP7] | |
640 | # Indicates the maximum length of A-MPDU pre-EOF padding that the STA can recv | |
641 | # This field is an integer in the range of 0 to 7. | |
642 | # The length defined by this field is equal to | |
179099e6 | 643 | # 2 pow(13 + Maximum A-MPDU Length Exponent) -1 octets |
efe45d14 MP |
644 | # |
645 | # VHT Link Adaptation Capable: [VHT-LINK-ADAPT2] [VHT-LINK-ADAPT3] | |
646 | # Indicates whether or not the STA supports link adaptation using VHT variant | |
647 | # HT Control field | |
648 | # If +HTC-VHTcapable is 1 | |
649 | # 0 = (no feedback) if the STA does not provide VHT MFB (default) | |
650 | # 1 = reserved | |
651 | # 2 = (Unsolicited) if the STA provides only unsolicited VHT MFB | |
652 | # 3 = (Both) if the STA can provide VHT MFB in response to VHT MRQ and if the | |
653 | # STA provides unsolicited VHT MFB | |
654 | # Reserved if +HTC-VHTcapable is 0 | |
655 | # | |
656 | # Rx Antenna Pattern Consistency: [RX-ANTENNA-PATTERN] | |
657 | # Indicates the possibility of Rx antenna pattern change | |
658 | # 0 = Rx antenna pattern might change during the lifetime of an association | |
659 | # 1 = Rx antenna pattern does not change during the lifetime of an association | |
660 | # | |
661 | # Tx Antenna Pattern Consistency: [TX-ANTENNA-PATTERN] | |
662 | # Indicates the possibility of Tx antenna pattern change | |
663 | # 0 = Tx antenna pattern might change during the lifetime of an association | |
664 | # 1 = Tx antenna pattern does not change during the lifetime of an association | |
665 | #vht_capab=[SHORT-GI-80][HTC-VHT] | |
140e850a MP |
666 | # |
667 | # Require stations to support VHT PHY (reject association if they do not) | |
668 | #require_vht=1 | |
6c93c38d MP |
669 | |
670 | # 0 = 20 or 40 MHz operating Channel width | |
671 | # 1 = 80 MHz channel width | |
672 | # 2 = 160 MHz channel width | |
673 | # 3 = 80+80 MHz channel width | |
efe45d14 | 674 | #vht_oper_chwidth=1 |
9615994e MP |
675 | # |
676 | # center freq = 5 GHz + (5 * index) | |
677 | # So index 42 gives center freq 5.210 GHz | |
678 | # which is channel 42 in 5G band | |
679 | # | |
680 | #vht_oper_centr_freq_seg0_idx=42 | |
3117ad42 JB |
681 | # |
682 | # center freq = 5 GHz + (5 * index) | |
683 | # So index 159 gives center freq 5.795 GHz | |
684 | # which is channel 159 in 5G band | |
685 | # | |
686 | #vht_oper_centr_freq_seg1_idx=159 | |
efe45d14 | 687 | |
fc72a48a T |
688 | # Workaround to use station's nsts capability in (Re)Association Response frame |
689 | # This may be needed with some deployed devices as an interoperability | |
690 | # workaround for beamforming if the AP's capability is greater than the | |
691 | # station's capability. This is disabled by default and can be enabled by | |
692 | # setting use_sta_nsts=1. | |
693 | #use_sta_nsts=0 | |
694 | ||
6fc6879b JM |
695 | ##### IEEE 802.1X-2004 related configuration ################################## |
696 | ||
697 | # Require IEEE 802.1X authorization | |
698 | #ieee8021x=1 | |
699 | ||
700 | # IEEE 802.1X/EAPOL version | |
701 | # hostapd is implemented based on IEEE Std 802.1X-2004 which defines EAPOL | |
702 | # version 2. However, there are many client implementations that do not handle | |
703 | # the new version number correctly (they seem to drop the frames completely). | |
704 | # In order to make hostapd interoperate with these clients, the version number | |
705 | # can be set to the older version (1) with this configuration value. | |
706 | #eapol_version=2 | |
707 | ||
708 | # Optional displayable message sent with EAP Request-Identity. The first \0 | |
709 | # in this string will be converted to ASCII-0 (nul). This can be used to | |
710 | # separate network info (comma separated list of attribute=value pairs); see, | |
711 | # e.g., RFC 4284. | |
712 | #eap_message=hello | |
713 | #eap_message=hello\0networkid=netw,nasid=foo,portid=0,NAIRealms=example.com | |
714 | ||
715 | # WEP rekeying (disabled if key lengths are not set or are set to 0) | |
716 | # Key lengths for default/broadcast and individual/unicast keys: | |
717 | # 5 = 40-bit WEP (also known as 64-bit WEP with 40 secret bits) | |
718 | # 13 = 104-bit WEP (also known as 128-bit WEP with 104 secret bits) | |
719 | #wep_key_len_broadcast=5 | |
720 | #wep_key_len_unicast=5 | |
721 | # Rekeying period in seconds. 0 = do not rekey (i.e., set keys only once) | |
722 | #wep_rekey_period=300 | |
723 | ||
724 | # EAPOL-Key index workaround (set bit7) for WinXP Supplicant (needed only if | |
725 | # only broadcast keys are used) | |
726 | eapol_key_index_workaround=0 | |
727 | ||
728 | # EAP reauthentication period in seconds (default: 3600 seconds; 0 = disable | |
729 | # reauthentication). | |
730 | #eap_reauth_period=3600 | |
731 | ||
732 | # Use PAE group address (01:80:c2:00:00:03) instead of individual target | |
733 | # address when sending EAPOL frames with driver=wired. This is the most common | |
734 | # mechanism used in wired authentication, but it also requires that the port | |
735 | # is only used by one station. | |
736 | #use_pae_group_addr=1 | |
737 | ||
2a5156a6 JM |
738 | # EAP Re-authentication Protocol (ERP) authenticator (RFC 6696) |
739 | # | |
740 | # Whether to initiate EAP authentication with EAP-Initiate/Re-auth-Start before | |
741 | # EAP-Identity/Request | |
742 | #erp_send_reauth_start=1 | |
743 | # | |
744 | # Domain name for EAP-Initiate/Re-auth-Start. Omitted from the message if not | |
d3bddd8b JM |
745 | # set (no local ER server). This is also used by the integrated EAP server if |
746 | # ERP is enabled (eap_server_erp=1). | |
2a5156a6 JM |
747 | #erp_domain=example.com |
748 | ||
6fc6879b JM |
749 | ##### Integrated EAP server ################################################### |
750 | ||
751 | # Optionally, hostapd can be configured to use an integrated EAP server | |
752 | # to process EAP authentication locally without need for an external RADIUS | |
753 | # server. This functionality can be used both as a local authentication server | |
754 | # for IEEE 802.1X/EAPOL and as a RADIUS server for other devices. | |
755 | ||
756 | # Use integrated EAP server instead of external RADIUS authentication | |
757 | # server. This is also needed if hostapd is configured to act as a RADIUS | |
758 | # authentication server. | |
759 | eap_server=0 | |
760 | ||
761 | # Path for EAP server user database | |
ee431d77 JM |
762 | # If SQLite support is included, this can be set to "sqlite:/path/to/sqlite.db" |
763 | # to use SQLite database instead of a text file. | |
6fc6879b JM |
764 | #eap_user_file=/etc/hostapd.eap_user |
765 | ||
766 | # CA certificate (PEM or DER file) for EAP-TLS/PEAP/TTLS | |
767 | #ca_cert=/etc/hostapd.ca.pem | |
768 | ||
769 | # Server certificate (PEM or DER file) for EAP-TLS/PEAP/TTLS | |
770 | #server_cert=/etc/hostapd.server.pem | |
771 | ||
772 | # Private key matching with the server certificate for EAP-TLS/PEAP/TTLS | |
773 | # This may point to the same file as server_cert if both certificate and key | |
774 | # are included in a single file. PKCS#12 (PFX) file (.p12/.pfx) can also be | |
775 | # used by commenting out server_cert and specifying the PFX file as the | |
776 | # private_key. | |
777 | #private_key=/etc/hostapd.server.prv | |
778 | ||
779 | # Passphrase for private key | |
780 | #private_key_passwd=secret passphrase | |
781 | ||
67fe933d JM |
782 | # Server identity |
783 | # EAP methods that provide mechanism for authenticated server identity delivery | |
784 | # use this value. If not set, "hostapd" is used as a default. | |
785 | #server_id=server.example.com | |
786 | ||
6fc6879b JM |
787 | # Enable CRL verification. |
788 | # Note: hostapd does not yet support CRL downloading based on CDP. Thus, a | |
789 | # valid CRL signed by the CA is required to be included in the ca_cert file. | |
790 | # This can be done by using PEM format for CA certificate and CRL and | |
791 | # concatenating these into one file. Whenever CRL changes, hostapd needs to be | |
792 | # restarted to take the new CRL into use. | |
793 | # 0 = do not verify CRLs (default) | |
794 | # 1 = check the CRL of the user certificate | |
795 | # 2 = check all CRLs in the certificate path | |
796 | #check_crl=1 | |
797 | ||
681e199d JM |
798 | # TLS Session Lifetime in seconds |
799 | # This can be used to allow TLS sessions to be cached and resumed with an | |
800 | # abbreviated handshake when using EAP-TLS/TTLS/PEAP. | |
801 | # (default: 0 = session caching and resumption disabled) | |
802 | #tls_session_lifetime=3600 | |
803 | ||
080585c0 JM |
804 | # Cached OCSP stapling response (DER encoded) |
805 | # If set, this file is sent as a certificate status response by the EAP server | |
806 | # if the EAP peer requests certificate status in the ClientHello message. | |
807 | # This cache file can be updated, e.g., by running following command | |
808 | # periodically to get an update from the OCSP responder: | |
809 | # openssl ocsp \ | |
810 | # -no_nonce \ | |
811 | # -CAfile /etc/hostapd.ca.pem \ | |
812 | # -issuer /etc/hostapd.ca.pem \ | |
813 | # -cert /etc/hostapd.server.pem \ | |
814 | # -url http://ocsp.example.com:8888/ \ | |
815 | # -respout /tmp/ocsp-cache.der | |
816 | #ocsp_stapling_response=/tmp/ocsp-cache.der | |
817 | ||
5addb0df JM |
818 | # Cached OCSP stapling response list (DER encoded OCSPResponseList) |
819 | # This is similar to ocsp_stapling_response, but the extended version defined in | |
820 | # RFC 6961 to allow multiple OCSP responses to be provided. | |
821 | #ocsp_stapling_response_multi=/tmp/ocsp-multi-cache.der | |
822 | ||
6fc6879b JM |
823 | # dh_file: File path to DH/DSA parameters file (in PEM format) |
824 | # This is an optional configuration file for setting parameters for an | |
825 | # ephemeral DH key exchange. In most cases, the default RSA authentication does | |
826 | # not use this configuration. However, it is possible setup RSA to use | |
827 | # ephemeral DH key exchange. In addition, ciphers with DSA keys always use | |
828 | # ephemeral DH keys. This can be used to achieve forward secrecy. If the file | |
829 | # is in DSA parameters format, it will be automatically converted into DH | |
830 | # params. This parameter is required if anonymous EAP-FAST is used. | |
29222cd3 | 831 | # You can generate DH parameters file with OpenSSL, e.g., |
7f2f3a67 | 832 | # "openssl dhparam -out /etc/hostapd.dh.pem 2048" |
6fc6879b JM |
833 | #dh_file=/etc/hostapd.dh.pem |
834 | ||
f8995f8f JM |
835 | # OpenSSL cipher string |
836 | # | |
837 | # This is an OpenSSL specific configuration option for configuring the default | |
838 | # ciphers. If not set, "DEFAULT:!EXP:!LOW" is used as the default. | |
839 | # See https://www.openssl.org/docs/apps/ciphers.html for OpenSSL documentation | |
840 | # on cipher suite configuration. This is applicable only if hostapd is built to | |
841 | # use OpenSSL. | |
842 | #openssl_ciphers=DEFAULT:!EXP:!LOW | |
843 | ||
7f6ec672 JM |
844 | # Fragment size for EAP methods |
845 | #fragment_size=1400 | |
846 | ||
43011639 DH |
847 | # Finite cyclic group for EAP-pwd. Number maps to group of domain parameters |
848 | # using the IANA repository for IKE (RFC 2409). | |
849 | #pwd_group=19 | |
850 | ||
6fc6879b JM |
851 | # Configuration data for EAP-SIM database/authentication gateway interface. |
852 | # This is a text string in implementation specific format. The example | |
853 | # implementation in eap_sim_db.c uses this as the UNIX domain socket name for | |
854 | # the HLR/AuC gateway (e.g., hlr_auc_gw). In this case, the path uses "unix:" | |
66979bb8 JM |
855 | # prefix. If hostapd is built with SQLite support (CONFIG_SQLITE=y in .config), |
856 | # database file can be described with an optional db=<path> parameter. | |
6fc6879b | 857 | #eap_sim_db=unix:/tmp/hlr_auc_gw.sock |
66979bb8 | 858 | #eap_sim_db=unix:/tmp/hlr_auc_gw.sock db=/tmp/hostapd.db |
6fc6879b | 859 | |
7b0f5500 FL |
860 | # EAP-SIM DB request timeout |
861 | # This parameter sets the maximum time to wait for a database request response. | |
862 | # The parameter value is in seconds. | |
863 | #eap_sim_db_timeout=1 | |
864 | ||
6fc6879b JM |
865 | # Encryption key for EAP-FAST PAC-Opaque values. This key must be a secret, |
866 | # random value. It is configured as a 16-octet value in hex format. It can be | |
867 | # generated, e.g., with the following command: | |
868 | # od -tx1 -v -N16 /dev/random | colrm 1 8 | tr -d ' ' | |
869 | #pac_opaque_encr_key=000102030405060708090a0b0c0d0e0f | |
870 | ||
871 | # EAP-FAST authority identity (A-ID) | |
2d867244 JM |
872 | # A-ID indicates the identity of the authority that issues PACs. The A-ID |
873 | # should be unique across all issuing servers. In theory, this is a variable | |
362bd35f | 874 | # length field, but due to some existing implementations requiring A-ID to be |
2d867244 | 875 | # 16 octets in length, it is strongly recommended to use that length for the |
362bd35f | 876 | # field to provid interoperability with deployed peer implementations. This |
2d867244 JM |
877 | # field is configured in hex format. |
878 | #eap_fast_a_id=101112131415161718191a1b1c1d1e1f | |
879 | ||
880 | # EAP-FAST authority identifier information (A-ID-Info) | |
881 | # This is a user-friendly name for the A-ID. For example, the enterprise name | |
882 | # and server name in a human-readable format. This field is encoded as UTF-8. | |
883 | #eap_fast_a_id_info=test server | |
6fc6879b | 884 | |
378eae5e JM |
885 | # Enable/disable different EAP-FAST provisioning modes: |
886 | #0 = provisioning disabled | |
887 | #1 = only anonymous provisioning allowed | |
888 | #2 = only authenticated provisioning allowed | |
889 | #3 = both provisioning modes allowed (default) | |
890 | #eap_fast_prov=3 | |
891 | ||
a11c90a6 JM |
892 | # EAP-FAST PAC-Key lifetime in seconds (hard limit) |
893 | #pac_key_lifetime=604800 | |
894 | ||
895 | # EAP-FAST PAC-Key refresh time in seconds (soft limit on remaining hard | |
896 | # limit). The server will generate a new PAC-Key when this number of seconds | |
897 | # (or fewer) of the lifetime remains. | |
898 | #pac_key_refresh_time=86400 | |
899 | ||
6fc6879b JM |
900 | # EAP-SIM and EAP-AKA protected success/failure indication using AT_RESULT_IND |
901 | # (default: 0 = disabled). | |
902 | #eap_sim_aka_result_ind=1 | |
903 | ||
502a293e JM |
904 | # Trusted Network Connect (TNC) |
905 | # If enabled, TNC validation will be required before the peer is allowed to | |
906 | # connect. Note: This is only used with EAP-TTLS and EAP-FAST. If any other | |
907 | # EAP method is enabled, the peer will be allowed to connect without TNC. | |
908 | #tnc=1 | |
909 | ||
d3bddd8b JM |
910 | # EAP Re-authentication Protocol (ERP) - RFC 6696 |
911 | # | |
912 | # Whether to enable ERP on the EAP server. | |
913 | #eap_server_erp=1 | |
6fc6879b JM |
914 | |
915 | ##### IEEE 802.11f - Inter-Access Point Protocol (IAPP) ####################### | |
916 | ||
917 | # Interface to be used for IAPP broadcast packets | |
918 | #iapp_interface=eth0 | |
919 | ||
920 | ||
921 | ##### RADIUS client configuration ############################################# | |
922 | # for IEEE 802.1X with external Authentication Server, IEEE 802.11 | |
923 | # authentication with external ACL for MAC addresses, and accounting | |
924 | ||
925 | # The own IP address of the access point (used as NAS-IP-Address) | |
926 | own_ip_addr=127.0.0.1 | |
927 | ||
251953bc JM |
928 | # NAS-Identifier string for RADIUS messages. When used, this should be unique |
929 | # to the NAS within the scope of the RADIUS server. Please note that hostapd | |
930 | # uses a separate RADIUS client for each BSS and as such, a unique | |
931 | # nas_identifier value should be configured separately for each BSS. This is | |
932 | # particularly important for cases where RADIUS accounting is used | |
933 | # (Accounting-On/Off messages are interpreted as clearing all ongoing sessions | |
934 | # and that may get interpreted as applying to all BSSes if the same | |
935 | # NAS-Identifier value is used.) For example, a fully qualified domain name | |
936 | # prefixed with a unique identifier of the BSS (e.g., BSSID) can be used here. | |
937 | # | |
6fc6879b JM |
938 | # When using IEEE 802.11r, nas_identifier must be set and must be between 1 and |
939 | # 48 octets long. | |
251953bc JM |
940 | # |
941 | # It is mandatory to configure either own_ip_addr or nas_identifier to be | |
942 | # compliant with the RADIUS protocol. When using RADIUS accounting, it is | |
943 | # strongly recommended that nas_identifier is set to a unique value for each | |
944 | # BSS. | |
6fc6879b JM |
945 | #nas_identifier=ap.example.com |
946 | ||
9836cb53 JM |
947 | # RADIUS client forced local IP address for the access point |
948 | # Normally the local IP address is determined automatically based on configured | |
949 | # IP addresses, but this field can be used to force a specific address to be | |
950 | # used, e.g., when the device has multiple IP addresses. | |
951 | #radius_client_addr=127.0.0.1 | |
952 | ||
6fc6879b JM |
953 | # RADIUS authentication server |
954 | #auth_server_addr=127.0.0.1 | |
955 | #auth_server_port=1812 | |
956 | #auth_server_shared_secret=secret | |
957 | ||
958 | # RADIUS accounting server | |
959 | #acct_server_addr=127.0.0.1 | |
960 | #acct_server_port=1813 | |
961 | #acct_server_shared_secret=secret | |
962 | ||
963 | # Secondary RADIUS servers; to be used if primary one does not reply to | |
964 | # RADIUS packets. These are optional and there can be more than one secondary | |
965 | # server listed. | |
966 | #auth_server_addr=127.0.0.2 | |
967 | #auth_server_port=1812 | |
968 | #auth_server_shared_secret=secret2 | |
969 | # | |
970 | #acct_server_addr=127.0.0.2 | |
971 | #acct_server_port=1813 | |
972 | #acct_server_shared_secret=secret2 | |
973 | ||
974 | # Retry interval for trying to return to the primary RADIUS server (in | |
975 | # seconds). RADIUS client code will automatically try to use the next server | |
976 | # when the current server is not replying to requests. If this interval is set, | |
977 | # primary server will be retried after configured amount of time even if the | |
978 | # currently used secondary server is still working. | |
979 | #radius_retry_primary_interval=600 | |
980 | ||
981 | ||
982 | # Interim accounting update interval | |
983 | # If this is set (larger than 0) and acct_server is configured, hostapd will | |
984 | # send interim accounting updates every N seconds. Note: if set, this overrides | |
985 | # possible Acct-Interim-Interval attribute in Access-Accept message. Thus, this | |
986 | # value should not be configured in hostapd.conf, if RADIUS server is used to | |
987 | # control the interim interval. | |
988 | # This value should not be less 600 (10 minutes) and must not be less than | |
989 | # 60 (1 minute). | |
990 | #radius_acct_interim_interval=600 | |
991 | ||
86f6053a JM |
992 | # Request Chargeable-User-Identity (RFC 4372) |
993 | # This parameter can be used to configure hostapd to request CUI from the | |
994 | # RADIUS server by including Chargeable-User-Identity attribute into | |
995 | # Access-Request packets. | |
996 | #radius_request_cui=1 | |
997 | ||
6fc6879b JM |
998 | # Dynamic VLAN mode; allow RADIUS authentication server to decide which VLAN |
999 | # is used for the stations. This information is parsed from following RADIUS | |
1000 | # attributes based on RFC 3580 and RFC 2868: Tunnel-Type (value 13 = VLAN), | |
1001 | # Tunnel-Medium-Type (value 6 = IEEE 802), Tunnel-Private-Group-ID (value | |
7ca902b5 MB |
1002 | # VLANID as a string). Optionally, the local MAC ACL list (accept_mac_file) can |
1003 | # be used to set static client MAC address to VLAN ID mapping. | |
6fc6879b JM |
1004 | # 0 = disabled (default) |
1005 | # 1 = option; use default interface if RADIUS server does not include VLAN ID | |
1006 | # 2 = required; reject authentication if RADIUS server does not include VLAN ID | |
1007 | #dynamic_vlan=0 | |
1008 | ||
8be640b7 MB |
1009 | # Per-Station AP_VLAN interface mode |
1010 | # If enabled, each station is assigned its own AP_VLAN interface. | |
1011 | # This implies per-station group keying and ebtables filtering of inter-STA | |
1012 | # traffic (when passed through the AP). | |
1013 | # If the sta is not assigned to any VLAN, then its AP_VLAN interface will be | |
1014 | # added to the bridge given by the "bridge" configuration option (see above). | |
1015 | # Otherwise, it will be added to the per-VLAN bridge. | |
1016 | # 0 = disabled (default) | |
1017 | # 1 = enabled | |
1018 | #per_sta_vif=0 | |
1019 | ||
6fc6879b JM |
1020 | # VLAN interface list for dynamic VLAN mode is read from a separate text file. |
1021 | # This list is used to map VLAN ID from the RADIUS server to a network | |
1022 | # interface. Each station is bound to one interface in the same way as with | |
1023 | # multiple BSSIDs or SSIDs. Each line in this text file is defining a new | |
1024 | # interface and the line must include VLAN ID and interface name separated by | |
1025 | # white space (space or tab). | |
7ca902b5 MB |
1026 | # If no entries are provided by this file, the station is statically mapped |
1027 | # to <bss-iface>.<vlan-id> interfaces. | |
6fc6879b JM |
1028 | #vlan_file=/etc/hostapd.vlan |
1029 | ||
1030 | # Interface where 802.1q tagged packets should appear when a RADIUS server is | |
1031 | # used to determine which VLAN a station is on. hostapd creates a bridge for | |
1032 | # each VLAN. Then hostapd adds a VLAN interface (associated with the interface | |
1033 | # indicated by 'vlan_tagged_interface') and the appropriate wireless interface | |
1034 | # to the bridge. | |
1035 | #vlan_tagged_interface=eth0 | |
1036 | ||
2aaeedfa | 1037 | # Bridge (prefix) to add the wifi and the tagged interface to. This gets the |
459eee92 MB |
1038 | # VLAN ID appended. It defaults to brvlan%d if no tagged interface is given |
1039 | # and br%s.%d if a tagged interface is given, provided %s = tagged interface | |
1040 | # and %d = VLAN ID. | |
2aaeedfa MB |
1041 | #vlan_bridge=brvlan |
1042 | ||
a00237ce MB |
1043 | # When hostapd creates a VLAN interface on vlan_tagged_interfaces, it needs |
1044 | # to know how to name it. | |
1045 | # 0 = vlan<XXX>, e.g., vlan1 | |
1046 | # 1 = <vlan_tagged_interface>.<XXX>, e.g. eth0.1 | |
1047 | #vlan_naming=0 | |
1048 | ||
af35e7af JM |
1049 | # Arbitrary RADIUS attributes can be added into Access-Request and |
1050 | # Accounting-Request packets by specifying the contents of the attributes with | |
1051 | # the following configuration parameters. There can be multiple of these to | |
1052 | # add multiple attributes. These parameters can also be used to override some | |
1053 | # of the attributes added automatically by hostapd. | |
1054 | # Format: <attr_id>[:<syntax:value>] | |
1055 | # attr_id: RADIUS attribute type (e.g., 26 = Vendor-Specific) | |
1056 | # syntax: s = string (UTF-8), d = integer, x = octet string | |
1057 | # value: attribute value in format indicated by the syntax | |
1058 | # If syntax and value parts are omitted, a null value (single 0x00 octet) is | |
1059 | # used. | |
1060 | # | |
1061 | # Additional Access-Request attributes | |
1062 | # radius_auth_req_attr=<attr_id>[:<syntax:value>] | |
1063 | # Examples: | |
1064 | # Operator-Name = "Operator" | |
1065 | #radius_auth_req_attr=126:s:Operator | |
1066 | # Service-Type = Framed (2) | |
1067 | #radius_auth_req_attr=6:d:2 | |
1068 | # Connect-Info = "testing" (this overrides the automatically generated value) | |
1069 | #radius_auth_req_attr=77:s:testing | |
1070 | # Same Connect-Info value set as a hexdump | |
1071 | #radius_auth_req_attr=77:x:74657374696e67 | |
1072 | ||
1073 | # | |
1074 | # Additional Accounting-Request attributes | |
1075 | # radius_acct_req_attr=<attr_id>[:<syntax:value>] | |
1076 | # Examples: | |
1077 | # Operator-Name = "Operator" | |
1078 | #radius_acct_req_attr=126:s:Operator | |
6fc6879b | 1079 | |
b031338c JM |
1080 | # Dynamic Authorization Extensions (RFC 5176) |
1081 | # This mechanism can be used to allow dynamic changes to user session based on | |
1082 | # commands from a RADIUS server (or some other disconnect client that has the | |
1083 | # needed session information). For example, Disconnect message can be used to | |
1084 | # request an associated station to be disconnected. | |
1085 | # | |
1086 | # This is disabled by default. Set radius_das_port to non-zero UDP port | |
1087 | # number to enable. | |
1088 | #radius_das_port=3799 | |
1089 | # | |
1090 | # DAS client (the host that can send Disconnect/CoA requests) and shared secret | |
1091 | #radius_das_client=192.168.1.123 shared secret here | |
bde7ba6c JM |
1092 | # |
1093 | # DAS Event-Timestamp time window in seconds | |
1094 | #radius_das_time_window=300 | |
1095 | # | |
1096 | # DAS require Event-Timestamp | |
1097 | #radius_das_require_event_timestamp=1 | |
42d30e9e NL |
1098 | # |
1099 | # DAS require Message-Authenticator | |
1100 | #radius_das_require_message_authenticator=1 | |
b031338c | 1101 | |
6fc6879b JM |
1102 | ##### RADIUS authentication server configuration ############################## |
1103 | ||
1104 | # hostapd can be used as a RADIUS authentication server for other hosts. This | |
1105 | # requires that the integrated EAP server is also enabled and both | |
1106 | # authentication services are sharing the same configuration. | |
1107 | ||
1108 | # File name of the RADIUS clients configuration for the RADIUS server. If this | |
1109 | # commented out, RADIUS server is disabled. | |
1110 | #radius_server_clients=/etc/hostapd.radius_clients | |
1111 | ||
1112 | # The UDP port number for the RADIUS authentication server | |
1113 | #radius_server_auth_port=1812 | |
1114 | ||
a1dd890a JM |
1115 | # The UDP port number for the RADIUS accounting server |
1116 | # Commenting this out or setting this to 0 can be used to disable RADIUS | |
1117 | # accounting while still enabling RADIUS authentication. | |
1118 | #radius_server_acct_port=1813 | |
1119 | ||
6fc6879b JM |
1120 | # Use IPv6 with RADIUS server (IPv4 will also be supported using IPv6 API) |
1121 | #radius_server_ipv6=1 | |
1122 | ||
1123 | ||
1124 | ##### WPA/IEEE 802.11i configuration ########################################## | |
1125 | ||
1126 | # Enable WPA. Setting this variable configures the AP to require WPA (either | |
1127 | # WPA-PSK or WPA-RADIUS/EAP based on other configuration). For WPA-PSK, either | |
1128 | # wpa_psk or wpa_passphrase must be set and wpa_key_mgmt must include WPA-PSK. | |
05ab9712 | 1129 | # Instead of wpa_psk / wpa_passphrase, wpa_psk_radius might suffice. |
6fc6879b JM |
1130 | # For WPA-RADIUS/EAP, ieee8021x must be set (but without dynamic WEP keys), |
1131 | # RADIUS authentication server must be configured, and WPA-EAP must be included | |
1132 | # in wpa_key_mgmt. | |
1133 | # This field is a bit field that can be used to enable WPA (IEEE 802.11i/D3.0) | |
1134 | # and/or WPA2 (full IEEE 802.11i/RSN): | |
1135 | # bit0 = WPA | |
1136 | # bit1 = IEEE 802.11i/RSN (WPA2) (dot11RSNAEnabled) | |
1137 | #wpa=1 | |
1138 | ||
1139 | # WPA pre-shared keys for WPA-PSK. This can be either entered as a 256-bit | |
1140 | # secret in hex format (64 hex digits), wpa_psk, or as an ASCII passphrase | |
1141 | # (8..63 characters) that will be converted to PSK. This conversion uses SSID | |
1142 | # so the PSK changes when ASCII passphrase is used and the SSID is changed. | |
1143 | # wpa_psk (dot11RSNAConfigPSKValue) | |
1144 | # wpa_passphrase (dot11RSNAConfigPSKPassPhrase) | |
1145 | #wpa_psk=0123456789abcdef0123456789abcdef0123456789abcdef0123456789abcdef | |
1146 | #wpa_passphrase=secret passphrase | |
1147 | ||
1148 | # Optionally, WPA PSKs can be read from a separate text file (containing list | |
1149 | # of (PSK,MAC address) pairs. This allows more than one PSK to be configured. | |
1150 | # Use absolute path name to make sure that the files can be read on SIGHUP | |
1151 | # configuration reloads. | |
1152 | #wpa_psk_file=/etc/hostapd.wpa_psk | |
1153 | ||
05ab9712 MB |
1154 | # Optionally, WPA passphrase can be received from RADIUS authentication server |
1155 | # This requires macaddr_acl to be set to 2 (RADIUS) | |
1156 | # 0 = disabled (default) | |
1157 | # 1 = optional; use default passphrase/psk if RADIUS server does not include | |
1158 | # Tunnel-Password | |
1159 | # 2 = required; reject authentication if RADIUS server does not include | |
1160 | # Tunnel-Password | |
1161 | #wpa_psk_radius=0 | |
1162 | ||
6fc6879b | 1163 | # Set of accepted key management algorithms (WPA-PSK, WPA-EAP, or both). The |
56586197 JM |
1164 | # entries are separated with a space. WPA-PSK-SHA256 and WPA-EAP-SHA256 can be |
1165 | # added to enable SHA256-based stronger algorithms. | |
6fc6879b JM |
1166 | # (dot11RSNAConfigAuthenticationSuitesTable) |
1167 | #wpa_key_mgmt=WPA-PSK WPA-EAP | |
1168 | ||
1169 | # Set of accepted cipher suites (encryption algorithms) for pairwise keys | |
1170 | # (unicast packets). This is a space separated list of algorithms: | |
1171 | # CCMP = AES in Counter mode with CBC-MAC [RFC 3610, IEEE 802.11i/D7.0] | |
1172 | # TKIP = Temporal Key Integrity Protocol [IEEE 802.11i/D7.0] | |
1173 | # Group cipher suite (encryption algorithm for broadcast and multicast frames) | |
1174 | # is automatically selected based on this configuration. If only CCMP is | |
1175 | # allowed as the pairwise cipher, group cipher will also be CCMP. Otherwise, | |
1176 | # TKIP will be used as the group cipher. | |
1177 | # (dot11RSNAConfigPairwiseCiphersTable) | |
1178 | # Pairwise cipher for WPA (v1) (default: TKIP) | |
1179 | #wpa_pairwise=TKIP CCMP | |
1180 | # Pairwise cipher for RSN/WPA2 (default: use wpa_pairwise value) | |
1181 | #rsn_pairwise=CCMP | |
1182 | ||
1183 | # Time interval for rekeying GTK (broadcast/multicast encryption keys) in | |
1184 | # seconds. (dot11RSNAConfigGroupRekeyTime) | |
1185 | #wpa_group_rekey=600 | |
1186 | ||
1187 | # Rekey GTK when any STA that possesses the current GTK is leaving the BSS. | |
1188 | # (dot11RSNAConfigGroupRekeyStrict) | |
1189 | #wpa_strict_rekey=1 | |
1190 | ||
1191 | # Time interval for rekeying GMK (master key used internally to generate GTKs | |
1192 | # (in seconds). | |
1193 | #wpa_gmk_rekey=86400 | |
1194 | ||
581a8cde JM |
1195 | # Maximum lifetime for PTK in seconds. This can be used to enforce rekeying of |
1196 | # PTK to mitigate some attacks against TKIP deficiencies. | |
1197 | #wpa_ptk_rekey=600 | |
1198 | ||
6fc6879b JM |
1199 | # Enable IEEE 802.11i/RSN/WPA2 pre-authentication. This is used to speed up |
1200 | # roaming be pre-authenticating IEEE 802.1X/EAP part of the full RSN | |
1201 | # authentication and key handshake before actually associating with a new AP. | |
1202 | # (dot11RSNAPreauthenticationEnabled) | |
1203 | #rsn_preauth=1 | |
1204 | # | |
1205 | # Space separated list of interfaces from which pre-authentication frames are | |
1206 | # accepted (e.g., 'eth0' or 'eth0 wlan0wds0'. This list should include all | |
1207 | # interface that are used for connections to other APs. This could include | |
1208 | # wired interfaces and WDS links. The normal wireless data interface towards | |
1209 | # associated stations (e.g., wlan0) should not be added, since | |
1210 | # pre-authentication is only used with APs other than the currently associated | |
1211 | # one. | |
1212 | #rsn_preauth_interfaces=eth0 | |
1213 | ||
1214 | # peerkey: Whether PeerKey negotiation for direct links (IEEE 802.11e) is | |
1215 | # allowed. This is only used with RSN/WPA2. | |
1216 | # 0 = disabled (default) | |
1217 | # 1 = enabled | |
1218 | #peerkey=1 | |
1219 | ||
5d22a1d5 | 1220 | # ieee80211w: Whether management frame protection (MFP) is enabled |
6fc6879b JM |
1221 | # 0 = disabled (default) |
1222 | # 1 = optional | |
1223 | # 2 = required | |
1224 | #ieee80211w=0 | |
1225 | ||
8dd9f9cd JM |
1226 | # Group management cipher suite |
1227 | # Default: AES-128-CMAC (BIP) | |
1228 | # Other options (depending on driver support): | |
1229 | # BIP-GMAC-128 | |
1230 | # BIP-GMAC-256 | |
1231 | # BIP-CMAC-256 | |
1232 | # Note: All the stations connecting to the BSS will also need to support the | |
1233 | # selected cipher. The default AES-128-CMAC is the only option that is commonly | |
1234 | # available in deployed devices. | |
1235 | #group_mgmt_cipher=AES-128-CMAC | |
1236 | ||
45c94154 JM |
1237 | # Association SA Query maximum timeout (in TU = 1.024 ms; for MFP) |
1238 | # (maximum time to wait for a SA Query response) | |
1239 | # dot11AssociationSAQueryMaximumTimeout, 1...4294967295 | |
1240 | #assoc_sa_query_max_timeout=1000 | |
1241 | ||
1242 | # Association SA Query retry timeout (in TU = 1.024 ms; for MFP) | |
1243 | # (time between two subsequent SA Query requests) | |
1244 | # dot11AssociationSAQueryRetryTimeout, 1...4294967295 | |
1245 | #assoc_sa_query_retry_timeout=201 | |
5d22a1d5 | 1246 | |
cb465555 JM |
1247 | # disable_pmksa_caching: Disable PMKSA caching |
1248 | # This parameter can be used to disable caching of PMKSA created through EAP | |
1249 | # authentication. RSN preauthentication may still end up using PMKSA caching if | |
1250 | # it is enabled (rsn_preauth=1). | |
1251 | # 0 = PMKSA caching enabled (default) | |
1252 | # 1 = PMKSA caching disabled | |
1253 | #disable_pmksa_caching=0 | |
5d22a1d5 | 1254 | |
bf98f7f3 JM |
1255 | # okc: Opportunistic Key Caching (aka Proactive Key Caching) |
1256 | # Allow PMK cache to be shared opportunistically among configured interfaces | |
1257 | # and BSSes (i.e., all configurations within a single hostapd process). | |
1258 | # 0 = disabled (default) | |
1259 | # 1 = enabled | |
1260 | #okc=1 | |
1261 | ||
d136c376 JM |
1262 | # SAE threshold for anti-clogging mechanism (dot11RSNASAEAntiCloggingThreshold) |
1263 | # This parameter defines how many open SAE instances can be in progress at the | |
1264 | # same time before the anti-clogging mechanism is taken into use. | |
1265 | #sae_anti_clogging_threshold=5 | |
6fc6879b | 1266 | |
625f202a JM |
1267 | # Enabled SAE finite cyclic groups |
1268 | # SAE implementation are required to support group 19 (ECC group defined over a | |
1269 | # 256-bit prime order field). All groups that are supported by the | |
1270 | # implementation are enabled by default. This configuration parameter can be | |
1271 | # used to specify a limited set of allowed groups. The group values are listed | |
1272 | # in the IANA registry: | |
1273 | # http://www.iana.org/assignments/ipsec-registry/ipsec-registry.xml#ipsec-registry-9 | |
1274 | #sae_groups=19 20 21 25 26 | |
1275 | ||
6fc6879b JM |
1276 | ##### IEEE 802.11r configuration ############################################## |
1277 | ||
1278 | # Mobility Domain identifier (dot11FTMobilityDomainID, MDID) | |
1279 | # MDID is used to indicate a group of APs (within an ESS, i.e., sharing the | |
1280 | # same SSID) between which a STA can use Fast BSS Transition. | |
1281 | # 2-octet identifier as a hex string. | |
1282 | #mobility_domain=a1b2 | |
1283 | ||
1284 | # PMK-R0 Key Holder identifier (dot11FTR0KeyHolderID) | |
1285 | # 1 to 48 octet identifier. | |
1286 | # This is configured with nas_identifier (see RADIUS client section above). | |
1287 | ||
1288 | # Default lifetime of the PMK-RO in minutes; range 1..65535 | |
1289 | # (dot11FTR0KeyLifetime) | |
1290 | #r0_key_lifetime=10000 | |
1291 | ||
1292 | # PMK-R1 Key Holder identifier (dot11FTR1KeyHolderID) | |
1293 | # 6-octet identifier as a hex string. | |
d48d1b88 | 1294 | # Defaults to BSSID. |
6fc6879b JM |
1295 | #r1_key_holder=000102030405 |
1296 | ||
1297 | # Reassociation deadline in time units (TUs / 1.024 ms; range 1000..65535) | |
1298 | # (dot11FTReassociationDeadline) | |
1299 | #reassociation_deadline=1000 | |
1300 | ||
1301 | # List of R0KHs in the same Mobility Domain | |
1302 | # format: <MAC address> <NAS Identifier> <128-bit key as hex string> | |
1303 | # This list is used to map R0KH-ID (NAS Identifier) to a destination MAC | |
1304 | # address when requesting PMK-R1 key from the R0KH that the STA used during the | |
1305 | # Initial Mobility Domain Association. | |
1306 | #r0kh=02:01:02:03:04:05 r0kh-1.example.com 000102030405060708090a0b0c0d0e0f | |
1307 | #r0kh=02:01:02:03:04:06 r0kh-2.example.com 00112233445566778899aabbccddeeff | |
1308 | # And so on.. One line per R0KH. | |
1309 | ||
1310 | # List of R1KHs in the same Mobility Domain | |
921a2786 | 1311 | # format: <MAC address> <R1KH-ID> <128-bit key as hex string> |
6fc6879b JM |
1312 | # This list is used to map R1KH-ID to a destination MAC address when sending |
1313 | # PMK-R1 key from the R0KH. This is also the list of authorized R1KHs in the MD | |
1314 | # that can request PMK-R1 keys. | |
1315 | #r1kh=02:01:02:03:04:05 02:11:22:33:44:55 000102030405060708090a0b0c0d0e0f | |
1316 | #r1kh=02:01:02:03:04:06 02:11:22:33:44:66 00112233445566778899aabbccddeeff | |
1317 | # And so on.. One line per R1KH. | |
1318 | ||
1319 | # Whether PMK-R1 push is enabled at R0KH | |
1320 | # 0 = do not push PMK-R1 to all configured R1KHs (default) | |
1321 | # 1 = push PMK-R1 to all configured R1KHs whenever a new PMK-R0 is derived | |
1322 | #pmk_r1_push=1 | |
1323 | ||
898a9790 JM |
1324 | # Whether to enable FT-over-DS |
1325 | # 0 = FT-over-DS disabled | |
1326 | # 1 = FT-over-DS enabled (default) | |
1327 | #ft_over_ds=1 | |
1328 | ||
61693eaa JM |
1329 | ##### Neighbor table ########################################################## |
1330 | # Maximum number of entries kept in AP table (either for neigbor table or for | |
1331 | # detecting Overlapping Legacy BSS Condition). The oldest entry will be | |
6fc6879b | 1332 | # removed when adding a new entry that would make the list grow over this |
61693eaa | 1333 | # limit. Note! WFA certification for IEEE 802.11g requires that OLBC is |
6fc6879b JM |
1334 | # enabled, so this field should not be set to 0 when using IEEE 802.11g. |
1335 | # default: 255 | |
1336 | #ap_table_max_size=255 | |
1337 | ||
1338 | # Number of seconds of no frames received after which entries may be deleted | |
1339 | # from the AP table. Since passive scanning is not usually performed frequently | |
1340 | # this should not be set to very small value. In addition, there is no | |
1341 | # guarantee that every scan cycle will receive beacon frames from the | |
1342 | # neighboring APs. | |
1343 | # default: 60 | |
1344 | #ap_table_expiration_time=3600 | |
1345 | ||
a65a9b8d JM |
1346 | # Maximum number of stations to track on the operating channel |
1347 | # This can be used to detect dualband capable stations before they have | |
1348 | # associated, e.g., to provide guidance on which colocated BSS to use. | |
1349 | # Default: 0 (disabled) | |
1350 | #track_sta_max_num=100 | |
1351 | ||
1352 | # Maximum age of a station tracking entry in seconds | |
1353 | # Default: 180 | |
1354 | #track_sta_max_age=180 | |
6fc6879b | 1355 | |
964f64e2 JM |
1356 | # Do not reply to group-addressed Probe Request from a station that was seen on |
1357 | # another radio. | |
1358 | # Default: Disabled | |
1359 | # | |
1360 | # This can be used with enabled track_sta_max_num configuration on another | |
1361 | # interface controlled by the same hostapd process to restrict Probe Request | |
1362 | # frame handling from replying to group-addressed Probe Request frames from a | |
1363 | # station that has been detected to be capable of operating on another band, | |
1364 | # e.g., to try to reduce likelihood of the station selecting a 2.4 GHz BSS when | |
1365 | # the AP operates both a 2.4 GHz and 5 GHz BSS concurrently. | |
1366 | # | |
1367 | # Note: Enabling this can cause connectivity issues and increase latency for | |
1368 | # discovering the AP. | |
1369 | #no_probe_resp_if_seen_on=wlan1 | |
1370 | ||
0e2412d0 JM |
1371 | # Reject authentication from a station that was seen on another radio. |
1372 | # Default: Disabled | |
1373 | # | |
1374 | # This can be used with enabled track_sta_max_num configuration on another | |
1375 | # interface controlled by the same hostapd process to reject authentication | |
1376 | # attempts from a station that has been detected to be capable of operating on | |
1377 | # another band, e.g., to try to reduce likelihood of the station selecting a | |
1378 | # 2.4 GHz BSS when the AP operates both a 2.4 GHz and 5 GHz BSS concurrently. | |
1379 | # | |
1380 | # Note: Enabling this can cause connectivity issues and increase latency for | |
1381 | # connecting with the AP. | |
1382 | #no_auth_if_seen_on=wlan1 | |
1383 | ||
ad08c363 JM |
1384 | ##### Wi-Fi Protected Setup (WPS) ############################################# |
1385 | ||
1386 | # WPS state | |
1387 | # 0 = WPS disabled (default) | |
1388 | # 1 = WPS enabled, not configured | |
1389 | # 2 = WPS enabled, configured | |
1390 | #wps_state=2 | |
1391 | ||
a679c0f2 JM |
1392 | # Whether to manage this interface independently from other WPS interfaces |
1393 | # By default, a single hostapd process applies WPS operations to all configured | |
1394 | # interfaces. This parameter can be used to disable that behavior for a subset | |
1395 | # of interfaces. If this is set to non-zero for an interface, WPS commands | |
1396 | # issued on that interface do not apply to other interfaces and WPS operations | |
1397 | # performed on other interfaces do not affect this interface. | |
1398 | #wps_independent=0 | |
1399 | ||
ad08c363 JM |
1400 | # AP can be configured into a locked state where new WPS Registrar are not |
1401 | # accepted, but previously authorized Registrars (including the internal one) | |
1402 | # can continue to add new Enrollees. | |
1403 | #ap_setup_locked=1 | |
1404 | ||
1405 | # Universally Unique IDentifier (UUID; see RFC 4122) of the device | |
1406 | # This value is used as the UUID for the internal WPS Registrar. If the AP | |
1407 | # is also using UPnP, this value should be set to the device's UPnP UUID. | |
79da74a2 | 1408 | # If not configured, UUID will be generated based on the local MAC address. |
ad08c363 JM |
1409 | #uuid=12345678-9abc-def0-1234-56789abcdef0 |
1410 | ||
1411 | # Note: If wpa_psk_file is set, WPS is used to generate random, per-device PSKs | |
1412 | # that will be appended to the wpa_psk_file. If wpa_psk_file is not set, the | |
1413 | # default PSK (wpa_psk/wpa_passphrase) will be delivered to Enrollees. Use of | |
1414 | # per-device PSKs is recommended as the more secure option (i.e., make sure to | |
1415 | # set wpa_psk_file when using WPS with WPA-PSK). | |
1416 | ||
1417 | # When an Enrollee requests access to the network with PIN method, the Enrollee | |
1418 | # PIN will need to be entered for the Registrar. PIN request notifications are | |
1419 | # sent to hostapd ctrl_iface monitor. In addition, they can be written to a | |
1420 | # text file that could be used, e.g., to populate the AP administration UI with | |
1421 | # pending PIN requests. If the following variable is set, the PIN requests will | |
1422 | # be written to the configured file. | |
1423 | #wps_pin_requests=/var/run/hostapd_wps_pin_requests | |
1424 | ||
1425 | # Device Name | |
1426 | # User-friendly description of device; up to 32 octets encoded in UTF-8 | |
1427 | #device_name=Wireless AP | |
1428 | ||
1429 | # Manufacturer | |
1430 | # The manufacturer of the device (up to 64 ASCII characters) | |
1431 | #manufacturer=Company | |
1432 | ||
1433 | # Model Name | |
1434 | # Model of the device (up to 32 ASCII characters) | |
1435 | #model_name=WAP | |
1436 | ||
1437 | # Model Number | |
1438 | # Additional device description (up to 32 ASCII characters) | |
1439 | #model_number=123 | |
1440 | ||
1441 | # Serial Number | |
1442 | # Serial number of the device (up to 32 characters) | |
1443 | #serial_number=12345 | |
1444 | ||
1445 | # Primary Device Type | |
1446 | # Used format: <categ>-<OUI>-<subcateg> | |
1447 | # categ = Category as an integer value | |
1448 | # OUI = OUI and type octet as a 4-octet hex-encoded value; 0050F204 for | |
1449 | # default WPS OUI | |
1450 | # subcateg = OUI-specific Sub Category as an integer value | |
1451 | # Examples: | |
1452 | # 1-0050F204-1 (Computer / PC) | |
1453 | # 1-0050F204-2 (Computer / Server) | |
1454 | # 5-0050F204-1 (Storage / NAS) | |
1455 | # 6-0050F204-1 (Network Infrastructure / AP) | |
1456 | #device_type=6-0050F204-1 | |
1457 | ||
1458 | # OS Version | |
1459 | # 4-octet operating system version number (hex string) | |
1460 | #os_version=01020300 | |
1461 | ||
1462 | # Config Methods | |
1463 | # List of the supported configuration methods | |
c0e4dd9e | 1464 | # Available methods: usba ethernet label display ext_nfc_token int_nfc_token |
6a857074 JM |
1465 | # nfc_interface push_button keypad virtual_display physical_display |
1466 | # virtual_push_button physical_push_button | |
1467 | #config_methods=label virtual_display virtual_push_button keypad | |
ad08c363 | 1468 | |
fa516558 JM |
1469 | # WPS capability discovery workaround for PBC with Windows 7 |
1470 | # Windows 7 uses incorrect way of figuring out AP's WPS capabilities by acting | |
1471 | # as a Registrar and using M1 from the AP. The config methods attribute in that | |
1472 | # message is supposed to indicate only the configuration method supported by | |
1473 | # the AP in Enrollee role, i.e., to add an external Registrar. For that case, | |
1474 | # PBC shall not be used and as such, the PushButton config method is removed | |
1475 | # from M1 by default. If pbc_in_m1=1 is included in the configuration file, | |
1476 | # the PushButton config method is left in M1 (if included in config_methods | |
1477 | # parameter) to allow Windows 7 to use PBC instead of PIN (e.g., from a label | |
1478 | # in the AP). | |
1479 | #pbc_in_m1=1 | |
1480 | ||
5a1cc30f | 1481 | # Static access point PIN for initial configuration and adding Registrars |
ad08c363 | 1482 | # If not set, hostapd will not allow external WPS Registrars to control the |
5a1cc30f JM |
1483 | # access point. The AP PIN can also be set at runtime with hostapd_cli |
1484 | # wps_ap_pin command. Use of temporary (enabled by user action) and random | |
1485 | # AP PIN is much more secure than configuring a static AP PIN here. As such, | |
1486 | # use of the ap_pin parameter is not recommended if the AP device has means for | |
1487 | # displaying a random PIN. | |
ad08c363 JM |
1488 | #ap_pin=12345670 |
1489 | ||
6fa68a0e JM |
1490 | # Skip building of automatic WPS credential |
1491 | # This can be used to allow the automatically generated Credential attribute to | |
1492 | # be replaced with pre-configured Credential(s). | |
1493 | #skip_cred_build=1 | |
1494 | ||
1495 | # Additional Credential attribute(s) | |
1496 | # This option can be used to add pre-configured Credential attributes into M8 | |
1497 | # message when acting as a Registrar. If skip_cred_build=1, this data will also | |
1498 | # be able to override the Credential attribute that would have otherwise been | |
1499 | # automatically generated based on network configuration. This configuration | |
1500 | # option points to an external file that much contain the WPS Credential | |
1501 | # attribute(s) as binary data. | |
1502 | #extra_cred=hostapd.cred | |
1503 | ||
d745c7cc JM |
1504 | # Credential processing |
1505 | # 0 = process received credentials internally (default) | |
1506 | # 1 = do not process received credentials; just pass them over ctrl_iface to | |
1507 | # external program(s) | |
1508 | # 2 = process received credentials internally and pass them over ctrl_iface | |
1509 | # to external program(s) | |
aabe26a1 JM |
1510 | # Note: With wps_cred_processing=1, skip_cred_build should be set to 1 and |
1511 | # extra_cred be used to provide the Credential data for Enrollees. | |
3b2cf800 JM |
1512 | # |
1513 | # wps_cred_processing=1 will disabled automatic updates of hostapd.conf file | |
1514 | # both for Credential processing and for marking AP Setup Locked based on | |
1515 | # validation failures of AP PIN. An external program is responsible on updating | |
1516 | # the configuration appropriately in this case. | |
d745c7cc JM |
1517 | #wps_cred_processing=0 |
1518 | ||
4c29cae9 JM |
1519 | # AP Settings Attributes for M7 |
1520 | # By default, hostapd generates the AP Settings Attributes for M7 based on the | |
1521 | # current configuration. It is possible to override this by providing a file | |
1522 | # with pre-configured attributes. This is similar to extra_cred file format, | |
1523 | # but the AP Settings attributes are not encapsulated in a Credential | |
1524 | # attribute. | |
1525 | #ap_settings=hostapd.ap_settings | |
ad08c363 | 1526 | |
f620268f JM |
1527 | # WPS UPnP interface |
1528 | # If set, support for external Registrars is enabled. | |
1529 | #upnp_iface=br0 | |
1530 | ||
1531 | # Friendly Name (required for UPnP) | |
1532 | # Short description for end use. Should be less than 64 characters. | |
1533 | #friendly_name=WPS Access Point | |
1534 | ||
1535 | # Manufacturer URL (optional for UPnP) | |
1536 | #manufacturer_url=http://www.example.com/ | |
1537 | ||
1538 | # Model Description (recommended for UPnP) | |
1539 | # Long description for end user. Should be less than 128 characters. | |
1540 | #model_description=Wireless Access Point | |
1541 | ||
1542 | # Model URL (optional for UPnP) | |
1543 | #model_url=http://www.example.com/model/ | |
1544 | ||
1545 | # Universal Product Code (optional for UPnP) | |
1546 | # 12-digit, all-numeric code that identifies the consumer package. | |
1547 | #upc=123456789012 | |
1548 | ||
01a02593 | 1549 | # WPS RF Bands (a = 5G, b = 2.4G, g = 2.4G, ag = dual band, ad = 60 GHz) |
8e5f9134 BC |
1550 | # This value should be set according to RF band(s) supported by the AP if |
1551 | # hw_mode is not set. For dual band dual concurrent devices, this needs to be | |
1552 | # set to ag to allow both RF bands to be advertized. | |
1553 | #wps_rf_bands=ag | |
1554 | ||
51ca03f4 JM |
1555 | # NFC password token for WPS |
1556 | # These parameters can be used to configure a fixed NFC password token for the | |
1557 | # AP. This can be generated, e.g., with nfc_pw_token from wpa_supplicant. When | |
1558 | # these parameters are used, the AP is assumed to be deployed with a NFC tag | |
1559 | # that includes the matching NFC password token (e.g., written based on the | |
1560 | # NDEF record from nfc_pw_token). | |
1561 | # | |
1562 | #wps_nfc_dev_pw_id: Device Password ID (16..65535) | |
1563 | #wps_nfc_dh_pubkey: Hexdump of DH Public Key | |
1564 | #wps_nfc_dh_privkey: Hexdump of DH Private Key | |
1565 | #wps_nfc_dev_pw: Hexdump of Device Password | |
1566 | ||
962473c1 JM |
1567 | ##### Wi-Fi Direct (P2P) ###################################################### |
1568 | ||
1569 | # Enable P2P Device management | |
1570 | #manage_p2p=1 | |
1571 | ||
31fd64cc JM |
1572 | # Allow cross connection |
1573 | #allow_cross_connection=1 | |
1574 | ||
1161ff1e JM |
1575 | #### TDLS (IEEE 802.11z-2010) ################################################# |
1576 | ||
1577 | # Prohibit use of TDLS in this BSS | |
1578 | #tdls_prohibit=1 | |
1579 | ||
1580 | # Prohibit use of TDLS Channel Switching in this BSS | |
1581 | #tdls_prohibit_chan_switch=1 | |
1582 | ||
39b97072 JM |
1583 | ##### IEEE 802.11v-2011 ####################################################### |
1584 | ||
1585 | # Time advertisement | |
1586 | # 0 = disabled (default) | |
1587 | # 2 = UTC time at which the TSF timer is 0 | |
1588 | #time_advertisement=2 | |
1589 | ||
1590 | # Local time zone as specified in 8.3 of IEEE Std 1003.1-2004: | |
1591 | # stdoffset[dst[offset][,start[/time],end[/time]]] | |
1592 | #time_zone=EST5 | |
1593 | ||
c79938a5 JM |
1594 | # WNM-Sleep Mode (extended sleep mode for stations) |
1595 | # 0 = disabled (default) | |
1596 | # 1 = enabled (allow stations to use WNM-Sleep Mode) | |
1597 | #wnm_sleep_mode=1 | |
1598 | ||
2049a875 JM |
1599 | # BSS Transition Management |
1600 | # 0 = disabled (default) | |
1601 | # 1 = enabled | |
1602 | #bss_transition=1 | |
1603 | ||
7d597d46 KP |
1604 | # Proxy ARP |
1605 | # 0 = disabled (default) | |
1606 | # 1 = enabled | |
1607 | #proxy_arp=1 | |
1608 | ||
4a7ce984 JM |
1609 | # IPv6 Neighbor Advertisement multicast-to-unicast conversion |
1610 | # This can be used with Proxy ARP to allow multicast NAs to be forwarded to | |
1611 | # associated STAs using link layer unicast delivery. | |
1612 | # 0 = disabled (default) | |
1613 | # 1 = enabled | |
1614 | #na_mcast_to_ucast=0 | |
1615 | ||
b83e3e93 JM |
1616 | ##### IEEE 802.11u-2011 ####################################################### |
1617 | ||
1618 | # Enable Interworking service | |
1619 | #interworking=1 | |
1620 | ||
1621 | # Access Network Type | |
1622 | # 0 = Private network | |
1623 | # 1 = Private network with guest access | |
1624 | # 2 = Chargeable public network | |
1625 | # 3 = Free public network | |
1626 | # 4 = Personal device network | |
1627 | # 5 = Emergency services only network | |
1628 | # 14 = Test or experimental | |
1629 | # 15 = Wildcard | |
1630 | #access_network_type=0 | |
1631 | ||
1632 | # Whether the network provides connectivity to the Internet | |
1633 | # 0 = Unspecified | |
1634 | # 1 = Network provides connectivity to the Internet | |
1635 | #internet=1 | |
1636 | ||
1637 | # Additional Step Required for Access | |
1638 | # Note: This is only used with open network, i.e., ASRA shall ne set to 0 if | |
1639 | # RSN is used. | |
1640 | #asra=0 | |
1641 | ||
1642 | # Emergency services reachable | |
1643 | #esr=0 | |
1644 | ||
1645 | # Unauthenticated emergency service accessible | |
1646 | #uesa=0 | |
1647 | ||
1648 | # Venue Info (optional) | |
1649 | # The available values are defined in IEEE Std 802.11u-2011, 7.3.1.34. | |
1650 | # Example values (group,type): | |
1651 | # 0,0 = Unspecified | |
1652 | # 1,7 = Convention Center | |
1653 | # 1,13 = Coffee Shop | |
1654 | # 2,0 = Unspecified Business | |
1655 | # 7,1 Private Residence | |
1656 | #venue_group=7 | |
1657 | #venue_type=1 | |
1658 | ||
1659 | # Homogeneous ESS identifier (optional; dot11HESSID) | |
1660 | # If set, this shall be identifical to one of the BSSIDs in the homogeneous | |
1661 | # ESS and this shall be set to the same value across all BSSs in homogeneous | |
1662 | # ESS. | |
1663 | #hessid=02:03:04:05:06:07 | |
1664 | ||
4b2a77ab JM |
1665 | # Roaming Consortium List |
1666 | # Arbitrary number of Roaming Consortium OIs can be configured with each line | |
1667 | # adding a new OI to the list. The first three entries are available through | |
1668 | # Beacon and Probe Response frames. Any additional entry will be available only | |
84946234 | 1669 | # through ANQP queries. Each OI is between 3 and 15 octets and is configured as |
4b2a77ab JM |
1670 | # a hexstring. |
1671 | #roaming_consortium=021122 | |
1672 | #roaming_consortium=2233445566 | |
1673 | ||
648cc711 JM |
1674 | # Venue Name information |
1675 | # This parameter can be used to configure one or more Venue Name Duples for | |
1676 | # Venue Name ANQP information. Each entry has a two or three character language | |
1677 | # code (ISO-639) separated by colon from the venue name string. | |
1678 | # Note that venue_group and venue_type have to be set for Venue Name | |
1679 | # information to be complete. | |
1680 | #venue_name=eng:Example venue | |
1681 | #venue_name=fin:Esimerkkipaikka | |
f224cf05 KP |
1682 | # Alternative format for language:value strings: |
1683 | # (double quoted string, printf-escaped string) | |
1684 | #venue_name=P"eng:Example\nvenue" | |
648cc711 | 1685 | |
550a3958 JK |
1686 | # Network Authentication Type |
1687 | # This parameter indicates what type of network authentication is used in the | |
1688 | # network. | |
1689 | # format: <network auth type indicator (1-octet hex str)> [redirect URL] | |
1690 | # Network Authentication Type Indicator values: | |
1691 | # 00 = Acceptance of terms and conditions | |
1692 | # 01 = On-line enrollment supported | |
1693 | # 02 = http/https redirection | |
1694 | # 03 = DNS redirection | |
1695 | #network_auth_type=00 | |
1696 | #network_auth_type=02http://www.example.com/redirect/me/here/ | |
1697 | ||
78bda93e JK |
1698 | # IP Address Type Availability |
1699 | # format: <1-octet encoded value as hex str> | |
1700 | # (ipv4_type & 0x3f) << 2 | (ipv6_type & 0x3) | |
1701 | # ipv4_type: | |
1702 | # 0 = Address type not available | |
1703 | # 1 = Public IPv4 address available | |
1704 | # 2 = Port-restricted IPv4 address available | |
1705 | # 3 = Single NATed private IPv4 address available | |
1706 | # 4 = Double NATed private IPv4 address available | |
1707 | # 5 = Port-restricted IPv4 address and single NATed IPv4 address available | |
1708 | # 6 = Port-restricted IPv4 address and double NATed IPv4 address available | |
1709 | # 7 = Availability of the address type is not known | |
1710 | # ipv6_type: | |
1711 | # 0 = Address type not available | |
1712 | # 1 = Address type available | |
1713 | # 2 = Availability of the address type not known | |
1714 | #ipaddr_type_availability=14 | |
1715 | ||
26fac8b6 JK |
1716 | # Domain Name |
1717 | # format: <variable-octet str>[,<variable-octet str>] | |
1718 | #domain_name=example.com,another.example.com,yet-another.example.com | |
1719 | ||
7515adb2 JK |
1720 | # 3GPP Cellular Network information |
1721 | # format: <MCC1,MNC1>[;<MCC2,MNC2>][;...] | |
1722 | #anqp_3gpp_cell_net=244,91;310,026;234,56 | |
1723 | ||
8047b186 JK |
1724 | # NAI Realm information |
1725 | # One or more realm can be advertised. Each nai_realm line adds a new realm to | |
1726 | # the set. These parameters provide information for stations using Interworking | |
1727 | # network selection to allow automatic connection to a network based on | |
1728 | # credentials. | |
1729 | # format: <encoding>,<NAI Realm(s)>[,<EAP Method 1>][,<EAP Method 2>][,...] | |
1730 | # encoding: | |
1731 | # 0 = Realm formatted in accordance with IETF RFC 4282 | |
1732 | # 1 = UTF-8 formatted character string that is not formatted in | |
1733 | # accordance with IETF RFC 4282 | |
1734 | # NAI Realm(s): Semi-colon delimited NAI Realm(s) | |
1735 | # EAP Method: <EAP Method>[:<[AuthParam1:Val1]>][<[AuthParam2:Val2]>][...] | |
cfc393a6 BG |
1736 | # EAP Method types, see: |
1737 | # http://www.iana.org/assignments/eap-numbers/eap-numbers.xhtml#eap-numbers-4 | |
8047b186 JK |
1738 | # AuthParam (Table 8-188 in IEEE Std 802.11-2012): |
1739 | # ID 2 = Non-EAP Inner Authentication Type | |
1740 | # 1 = PAP, 2 = CHAP, 3 = MSCHAP, 4 = MSCHAPV2 | |
1741 | # ID 3 = Inner authentication EAP Method Type | |
1742 | # ID 5 = Credential Type | |
1743 | # 1 = SIM, 2 = USIM, 3 = NFC Secure Element, 4 = Hardware Token, | |
1744 | # 5 = Softoken, 6 = Certificate, 7 = username/password, 9 = Anonymous, | |
1745 | # 10 = Vendor Specific | |
1746 | #nai_realm=0,example.com;example.net | |
1747 | # EAP methods EAP-TLS with certificate and EAP-TTLS/MSCHAPv2 with | |
1748 | # username/password | |
1749 | #nai_realm=0,example.org,13[5:6],21[2:4][5:7] | |
1750 | ||
695dbbea JM |
1751 | # Arbitrary ANQP-element configuration |
1752 | # Additional ANQP-elements with arbitrary values can be defined by specifying | |
1753 | # their contents in raw format as a hexdump of the payload. Note that these | |
1754 | # values will override ANQP-element contents that may have been specified in the | |
1755 | # more higher layer configuration parameters listed above. | |
1756 | # format: anqp_elem=<InfoID>:<hexdump of payload> | |
1757 | # For example, AP Geospatial Location ANQP-element with unknown location: | |
1758 | #anqp_elem=265:0000 | |
1759 | # For example, AP Civic Location ANQP-element with unknown location: | |
1760 | #anqp_elem=266:000000 | |
1761 | ||
83594725 JM |
1762 | # GAS Address 3 behavior |
1763 | # 0 = P2P specification (Address3 = AP BSSID) workaround enabled by default | |
1764 | # based on GAS request Address3 | |
1765 | # 1 = IEEE 802.11 standard compliant regardless of GAS request Address3 | |
1766 | # 2 = Force non-compliant behavior (Address3 = AP BSSID for all cases) | |
1767 | #gas_address3=0 | |
1768 | ||
c551700f KP |
1769 | # QoS Map Set configuration |
1770 | # | |
1771 | # Comma delimited QoS Map Set in decimal values | |
1772 | # (see IEEE Std 802.11-2012, 8.4.2.97) | |
1773 | # | |
1774 | # format: | |
1775 | # [<DSCP Exceptions[DSCP,UP]>,]<UP 0 range[low,high]>,...<UP 7 range[low,high]> | |
1776 | # | |
1777 | # There can be up to 21 optional DSCP Exceptions which are pairs of DSCP Value | |
1778 | # (0..63 or 255) and User Priority (0..7). This is followed by eight DSCP Range | |
1779 | # descriptions with DSCP Low Value and DSCP High Value pairs (0..63 or 255) for | |
1780 | # each UP starting from 0. If both low and high value are set to 255, the | |
1781 | # corresponding UP is not used. | |
1782 | # | |
1783 | # default: not set | |
1784 | #qos_map_set=53,2,22,6,8,15,0,7,255,255,16,31,32,39,255,255,40,47,255,255 | |
1785 | ||
159c89ab JK |
1786 | ##### Hotspot 2.0 ############################################################# |
1787 | ||
1788 | # Enable Hotspot 2.0 support | |
1789 | #hs20=1 | |
1790 | ||
83421850 JM |
1791 | # Disable Downstream Group-Addressed Forwarding (DGAF) |
1792 | # This can be used to configure a network where no group-addressed frames are | |
1793 | # allowed. The AP will not forward any group-address frames to the stations and | |
1794 | # random GTKs are issued for each station to prevent associated stations from | |
1795 | # forging such frames to other stations in the BSS. | |
1796 | #disable_dgaf=1 | |
1797 | ||
a14896e8 JM |
1798 | # OSU Server-Only Authenticated L2 Encryption Network |
1799 | #osen=1 | |
1800 | ||
d5d24784 JM |
1801 | # ANQP Domain ID (0..65535) |
1802 | # An identifier for a set of APs in an ESS that share the same common ANQP | |
1803 | # information. 0 = Some of the ANQP information is unique to this AP (default). | |
1804 | #anqp_domain_id=1234 | |
1805 | ||
8e1146d9 JM |
1806 | # Deauthentication request timeout |
1807 | # If the RADIUS server indicates that the station is not allowed to connect to | |
1808 | # the BSS/ESS, the AP can allow the station some time to download a | |
1809 | # notification page (URL included in the message). This parameter sets that | |
1810 | # timeout in seconds. | |
1811 | #hs20_deauth_req_timeout=60 | |
1812 | ||
a9277e85 JK |
1813 | # Operator Friendly Name |
1814 | # This parameter can be used to configure one or more Operator Friendly Name | |
1815 | # Duples. Each entry has a two or three character language code (ISO-639) | |
1816 | # separated by colon from the operator friendly name string. | |
1817 | #hs20_oper_friendly_name=eng:Example operator | |
1818 | #hs20_oper_friendly_name=fin:Esimerkkioperaattori | |
1819 | ||
5ccc54aa JK |
1820 | # Connection Capability |
1821 | # This can be used to advertise what type of IP traffic can be sent through the | |
1822 | # hotspot (e.g., due to firewall allowing/blocking protocols/ports). | |
1823 | # format: <IP Protocol>:<Port Number>:<Status> | |
1824 | # IP Protocol: 1 = ICMP, 6 = TCP, 17 = UDP | |
1825 | # Port Number: 0..65535 | |
1826 | # Status: 0 = Closed, 1 = Open, 2 = Unknown | |
1827 | # Each hs20_conn_capab line is added to the list of advertised tuples. | |
1828 | #hs20_conn_capab=1:0:2 | |
1829 | #hs20_conn_capab=6:22:1 | |
1830 | #hs20_conn_capab=17:5060:0 | |
1831 | ||
4065a309 JK |
1832 | # WAN Metrics |
1833 | # format: <WAN Info>:<DL Speed>:<UL Speed>:<DL Load>:<UL Load>:<LMD> | |
1834 | # WAN Info: B0-B1: Link Status, B2: Symmetric Link, B3: At Capabity | |
1835 | # (encoded as two hex digits) | |
1836 | # Link Status: 1 = Link up, 2 = Link down, 3 = Link in test state | |
1837 | # Downlink Speed: Estimate of WAN backhaul link current downlink speed in kbps; | |
1838 | # 1..4294967295; 0 = unknown | |
1839 | # Uplink Speed: Estimate of WAN backhaul link current uplink speed in kbps | |
1840 | # 1..4294967295; 0 = unknown | |
1841 | # Downlink Load: Current load of downlink WAN connection (scaled to 255 = 100%) | |
1842 | # Uplink Load: Current load of uplink WAN connection (scaled to 255 = 100%) | |
1843 | # Load Measurement Duration: Duration for measuring downlink/uplink load in | |
1844 | # tenths of a second (1..65535); 0 if load cannot be determined | |
1845 | #hs20_wan_metrics=01:8000:1000:80:240:3000 | |
5ccc54aa | 1846 | |
df5934f1 JK |
1847 | # Operating Class Indication |
1848 | # List of operating classes the BSSes in this ESS use. The Global operating | |
1849 | # classes in Table E-4 of IEEE Std 802.11-2012 Annex E define the values that | |
1850 | # can be used in this. | |
1851 | # format: hexdump of operating class octets | |
1852 | # for example, operating classes 81 (2.4 GHz channels 1-13) and 115 (5 GHz | |
1853 | # channels 36-48): | |
1854 | #hs20_operating_class=5173 | |
1855 | ||
f7bd7a01 JM |
1856 | # OSU icons |
1857 | # <Icon Width>:<Icon Height>:<Language code>:<Icon Type>:<Name>:<file path> | |
1858 | #hs20_icon=32:32:eng:image/png:icon32:/tmp/icon32.png | |
1859 | #hs20_icon=64:64:eng:image/png:icon64:/tmp/icon64.png | |
1860 | ||
ae6d15c7 JM |
1861 | # OSU SSID (see ssid2 for format description) |
1862 | # This is the SSID used for all OSU connections to all the listed OSU Providers. | |
1863 | #osu_ssid="example" | |
1864 | ||
1865 | # OSU Providers | |
1866 | # One or more sets of following parameter. Each OSU provider is started by the | |
1867 | # mandatory osu_server_uri item. The other parameters add information for the | |
1868 | # last added OSU provider. | |
1869 | # | |
1870 | #osu_server_uri=https://example.com/osu/ | |
1871 | #osu_friendly_name=eng:Example operator | |
1872 | #osu_friendly_name=fin:Esimerkkipalveluntarjoaja | |
1873 | #osu_nai=anonymous@example.com | |
1874 | #osu_method_list=1 0 | |
1875 | #osu_icon=icon32 | |
1876 | #osu_icon=icon64 | |
1877 | #osu_service_desc=eng:Example services | |
1878 | #osu_service_desc=fin:Esimerkkipalveluja | |
1879 | # | |
1880 | #osu_server_uri=... | |
1881 | ||
104bef45 AN |
1882 | ##### Fast Session Transfer (FST) support ##################################### |
1883 | # | |
1884 | # The options in this section are only available when the build configuration | |
1885 | # option CONFIG_FST is set while compiling hostapd. They allow this interface | |
1886 | # to be a part of FST setup. | |
1887 | # | |
1888 | # FST is the transfer of a session from a channel to another channel, in the | |
1889 | # same or different frequency bands. | |
1890 | # | |
1891 | # For detals, see IEEE Std 802.11ad-2012. | |
1892 | ||
1893 | # Identifier of an FST Group the interface belongs to. | |
1894 | #fst_group_id=bond0 | |
1895 | ||
1896 | # Interface priority within the FST Group. | |
1897 | # Announcing a higher priority for an interface means declaring it more | |
1898 | # preferable for FST switch. | |
1899 | # fst_priority is in 1..255 range with 1 being the lowest priority. | |
1900 | #fst_priority=100 | |
1901 | ||
1902 | # Default LLT value for this interface in milliseconds. The value used in case | |
1903 | # no value provided during session setup. Default is 50 ms. | |
1904 | # fst_llt is in 1..4294967 range (due to spec limitation, see 10.32.2.2 | |
1905 | # Transitioning between states). | |
1906 | #fst_llt=100 | |
1907 | ||
74e982d8 DS |
1908 | ##### Radio measurements / location ########################################### |
1909 | ||
1910 | # The content of a LCI measurement subelement | |
1911 | #lci=<Hexdump of binary data of the LCI report> | |
1912 | ||
1913 | # The content of a location civic measurement subelement | |
1914 | #civic=<Hexdump of binary data of the location civic report> | |
1915 | ||
01018212 DS |
1916 | # Enable neighbor report via radio measurements |
1917 | #rrm_neighbor_report=1 | |
1918 | ||
faecb392 LD |
1919 | # Publish fine timing measurement (FTM) responder functionality |
1920 | # This parameter only controls publishing via Extended Capabilities element. | |
1921 | # Actual functionality is managed outside hostapd. | |
1922 | #ftm_responder=0 | |
1923 | ||
1924 | # Publish fine timing measurement (FTM) initiator functionality | |
1925 | # This parameter only controls publishing via Extended Capabilities element. | |
1926 | # Actual functionality is managed outside hostapd. | |
1927 | #ftm_initiator=0 | |
1928 | ||
c2aff6b1 JB |
1929 | ##### TESTING OPTIONS ######################################################### |
1930 | # | |
1931 | # The options in this section are only available when the build configuration | |
1932 | # option CONFIG_TESTING_OPTIONS is set while compiling hostapd. They allow | |
1933 | # testing some scenarios that are otherwise difficult to reproduce. | |
1934 | # | |
1935 | # Ignore probe requests sent to hostapd with the given probability, must be a | |
1936 | # floating point number in the range [0, 1). | |
1937 | #ignore_probe_probability=0.0 | |
1938 | # | |
1939 | # Ignore authentication frames with the given probability | |
1940 | #ignore_auth_probability=0.0 | |
1941 | # | |
1942 | # Ignore association requests with the given probability | |
1943 | #ignore_assoc_probability=0.0 | |
1944 | # | |
1945 | # Ignore reassociation requests with the given probability | |
1946 | #ignore_reassoc_probability=0.0 | |
7af092a0 JB |
1947 | # |
1948 | # Corrupt Key MIC in GTK rekey EAPOL-Key frames with the given probability | |
1949 | #corrupt_gtk_rekey_mic_probability=0.0 | |
2b6e1216 JB |
1950 | # |
1951 | # Include only ECSA IE without CSA IE where possible | |
1952 | # (channel switch operating class is needed) | |
1953 | #ecsa_ie_only=0 | |
c2aff6b1 | 1954 | |
6fc6879b JM |
1955 | ##### Multiple BSSID support ################################################## |
1956 | # | |
1957 | # Above configuration is using the default interface (wlan#, or multi-SSID VLAN | |
1958 | # interfaces). Other BSSIDs can be added by using separator 'bss' with | |
1959 | # default interface name to be allocated for the data packets of the new BSS. | |
1960 | # | |
1961 | # hostapd will generate BSSID mask based on the BSSIDs that are | |
1962 | # configured. hostapd will verify that dev_addr & MASK == dev_addr. If this is | |
1963 | # not the case, the MAC address of the radio must be changed before starting | |
90ac1f9f JM |
1964 | # hostapd (ifconfig wlan0 hw ether <MAC addr>). If a BSSID is configured for |
1965 | # every secondary BSS, this limitation is not applied at hostapd and other | |
1966 | # masks may be used if the driver supports them (e.g., swap the locally | |
1967 | # administered bit) | |
6fc6879b JM |
1968 | # |
1969 | # BSSIDs are assigned in order to each BSS, unless an explicit BSSID is | |
1970 | # specified using the 'bssid' parameter. | |
1971 | # If an explicit BSSID is specified, it must be chosen such that it: | |
1972 | # - results in a valid MASK that covers it and the dev_addr | |
1973 | # - is not the same as the MAC address of the radio | |
1974 | # - is not the same as any other explicitly specified BSSID | |
1975 | # | |
6448e064 EP |
1976 | # Alternatively, the 'use_driver_iface_addr' parameter can be used to request |
1977 | # hostapd to use the driver auto-generated interface address (e.g., to use the | |
1978 | # exact MAC addresses allocated to the device). | |
1979 | # | |
978c6730 JM |
1980 | # Not all drivers support multiple BSSes. The exact mechanism for determining |
1981 | # the driver capabilities is driver specific. With the current (i.e., a recent | |
1982 | # kernel) drivers using nl80211, this information can be checked with "iw list" | |
1983 | # (search for "valid interface combinations"). | |
1984 | # | |
6fc6879b JM |
1985 | # Please note that hostapd uses some of the values configured for the first BSS |
1986 | # as the defaults for the following BSSes. However, it is recommended that all | |
1987 | # BSSes include explicit configuration of all relevant configuration items. | |
1988 | # | |
1989 | #bss=wlan0_0 | |
1990 | #ssid=test2 | |
1991 | # most of the above items can be used here (apart from radio interface specific | |
1992 | # items, like channel) | |
1993 | ||
1994 | #bss=wlan0_1 | |
1995 | #bssid=00:13:10:95:fe:0b | |
1996 | # ... |