]>
Commit | Line | Data |
---|---|---|
0f8c9768 WD |
1 | /* |
2 | * A collection of structures, addresses, and values associated with | |
3 | * the Motorola 860T FADS board. Copied from the MBX stuff. | |
4 | * Magnus Damm added defines for 8xxrom and extended bd_info. | |
5 | * Helmut Buchsbaum added bitvalues for BCSRx | |
6 | * | |
7 | * Copyright (c) 1998 Dan Malek (dmalek@jlc.net) | |
8 | */ | |
9 | ||
10 | /* | |
11 | * 1999-nov-26: The FADS is using the following physical memorymap: | |
12 | * | |
13 | * ff020000 -> ff02ffff : pcmcia | |
14 | * ff010000 -> ff01ffff : BCSR connected to CS1, setup by 8xxrom | |
15 | * ff000000 -> ff00ffff : IMAP internal in the cpu | |
16 | * fe000000 -> ffnnnnnn : flash connected to CS0, setup by 8xxrom | |
17 | * 00000000 -> nnnnnnnn : sdram/dram setup by 8xxrom | |
18 | */ | |
19 | ||
20 | /* ------------------------------------------------------------------------- */ | |
21 | ||
22 | /* | |
23 | * board/config.h - configuration options, board specific | |
24 | */ | |
25 | ||
26 | #ifndef __CONFIG_H | |
27 | #define __CONFIG_H | |
28 | ||
29 | /* | |
30 | * High Level Configuration Options | |
31 | * (easy to change) | |
32 | */ | |
0f8c9768 WD |
33 | #define CONFIG_MPC850 1 |
34 | #define CONFIG_MPC850SAR 1 | |
35 | #define CONFIG_FADS 1 | |
36 | ||
2ae18241 WD |
37 | #define CONFIG_SYS_TEXT_BASE 0xFE000000 |
38 | ||
0f8c9768 WD |
39 | #define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */ |
40 | #undef CONFIG_8xx_CONS_SMC2 | |
41 | #undef CONFIG_8xx_CONS_NONE | |
42 | #define CONFIG_BAUDRATE 9600 | |
43 | ||
44 | #if 0 | |
45 | #define MPC8XX_FACT 10 /* Multiply by 10 */ | |
46 | #define MPC8XX_XIN 50000000 /* 50 MHz in */ | |
47 | #else | |
48 | #define MPC8XX_FACT 12 /* Multiply by 12 */ | |
49 | #define MPC8XX_XIN 4000000 /* 4 MHz in */ | |
50 | #endif | |
51 | #define MPC8XX_HZ ((MPC8XX_XIN) * (MPC8XX_FACT)) | |
52 | ||
53 | #define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */ | |
54 | ||
55 | #if 1 | |
56 | #define CONFIG_BOOTDELAY -1 /* autoboot disabled */ | |
57 | #else | |
58 | #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ | |
59 | #endif | |
60 | ||
61 | #define CONFIG_BOOTCOMMAND "bootm 02880000" /* autoboot command */ | |
62 | #define CONFIG_BOOTARGS " " | |
63 | ||
64 | #undef CONFIG_WATCHDOG /* watchdog disabled */ | |
65 | ||
60a0876b | 66 | |
11799434 JL |
67 | /* |
68 | * BOOTP options | |
69 | */ | |
70 | #define CONFIG_BOOTP_BOOTFILESIZE | |
71 | #define CONFIG_BOOTP_BOOTPATH | |
72 | #define CONFIG_BOOTP_GATEWAY | |
73 | #define CONFIG_BOOTP_HOSTNAME | |
74 | ||
75 | ||
60a0876b JL |
76 | /* |
77 | * Command line configuration. | |
78 | */ | |
79 | #include <config_cmd_default.h> | |
80 | ||
0f8c9768 WD |
81 | |
82 | /* | |
83 | * Miscellaneous configurable options | |
84 | */ | |
6d0f6bcf JCPV |
85 | #undef CONFIG_SYS_LONGHELP /* undef to save memory */ |
86 | #define CONFIG_SYS_PROMPT ":>" /* Monitor Command Prompt */ | |
60a0876b | 87 | #if defined(CONFIG_CMD_KGDB) |
6d0f6bcf | 88 | #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
0f8c9768 | 89 | #else |
6d0f6bcf | 90 | #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
0f8c9768 | 91 | #endif |
6d0f6bcf JCPV |
92 | #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
93 | #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ | |
94 | #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ | |
0f8c9768 | 95 | |
6d0f6bcf JCPV |
96 | #define CONFIG_SYS_MEMTEST_START 0x00004000 /* memtest works on */ |
97 | #define CONFIG_SYS_MEMTEST_END 0x00800000 /* 0 ... 8 MB in DRAM */ | |
0f8c9768 | 98 | |
6d0f6bcf | 99 | #define CONFIG_SYS_LOAD_ADDR 0x00100000 /* default load address */ |
0f8c9768 | 100 | |
6d0f6bcf | 101 | #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ |
0f8c9768 | 102 | |
0f8c9768 WD |
103 | /* |
104 | * Low Level Configuration Settings | |
105 | * (address mappings, register initial values, etc.) | |
106 | * You should know what you are doing if you make changes here. | |
107 | */ | |
108 | /*----------------------------------------------------------------------- | |
109 | * Internal Memory Mapped Register | |
110 | */ | |
6d0f6bcf JCPV |
111 | #define CONFIG_SYS_IMMR 0xFF000000 |
112 | #define CONFIG_SYS_IMMR_SIZE ((uint)(64 * 1024)) | |
0f8c9768 WD |
113 | |
114 | /*----------------------------------------------------------------------- | |
115 | * Definitions for initial stack pointer and data area (in DPRAM) | |
116 | */ | |
6d0f6bcf | 117 | #define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR |
553f0982 | 118 | #define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */ |
25ddd1fb | 119 | #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
6d0f6bcf | 120 | #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
0f8c9768 WD |
121 | |
122 | /*----------------------------------------------------------------------- | |
123 | * Start addresses for the final memory configuration | |
124 | * (Set up by the startup code) | |
6d0f6bcf | 125 | * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 |
0f8c9768 WD |
126 | * Also NOTE that it doesn't mean SDRAM - it means MEMORY. |
127 | */ | |
6d0f6bcf JCPV |
128 | #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
129 | #define CONFIG_SYS_SDRAM_SIZE (4<<20) /* standard FADS has 4M */ | |
130 | #define CONFIG_SYS_FLASH_BASE 0x02800000 | |
131 | #define CONFIG_SYS_FLASH_SIZE ((uint)(8 * 1024 * 1024)) /* max 8Mbyte */ | |
0f8c9768 | 132 | #if 0 |
6d0f6bcf | 133 | #define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 128 kB for Monitor */ |
0f8c9768 | 134 | #else |
6d0f6bcf | 135 | #define CONFIG_SYS_MONITOR_LEN (512 << 10) /* Reserve 512 kB for Monitor */ |
0f8c9768 | 136 | #endif |
6d0f6bcf JCPV |
137 | #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE |
138 | #define CONFIG_SYS_MALLOC_LEN (256 << 10) /* Reserve 128 kB for malloc() */ | |
0f8c9768 WD |
139 | |
140 | /* | |
141 | * For booting Linux, the board info and command line data | |
142 | * have to be in the first 8 MB of memory, since this is | |
143 | * the maximum mapped by the Linux kernel during initialization. | |
144 | */ | |
6d0f6bcf | 145 | #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
0f8c9768 WD |
146 | /*----------------------------------------------------------------------- |
147 | * FLASH organization | |
148 | */ | |
6d0f6bcf JCPV |
149 | #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
150 | #define CONFIG_SYS_MAX_FLASH_SECT 8 /* max number of sectors on one chip */ | |
0f8c9768 | 151 | |
6d0f6bcf JCPV |
152 | #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ |
153 | #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ | |
0f8c9768 | 154 | |
5a1aceb0 | 155 | #define CONFIG_ENV_IS_IN_FLASH 1 |
0e8d1586 JCPV |
156 | #define CONFIG_ENV_OFFSET 0x00040000 /* Offset of Environment Sector */ |
157 | #define CONFIG_ENV_SIZE 0x40000 /* Total Size of Environment Sector */ | |
6d0f6bcf | 158 | #define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */ |
0f8c9768 WD |
159 | |
160 | /*----------------------------------------------------------------------- | |
161 | * Cache Configuration | |
162 | */ | |
6d0f6bcf | 163 | #define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */ |
60a0876b | 164 | #if defined(CONFIG_CMD_KGDB) |
6d0f6bcf | 165 | #define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */ |
0f8c9768 WD |
166 | #endif |
167 | ||
168 | /*----------------------------------------------------------------------- | |
169 | * SYPCR - System Protection Control 11-9 | |
170 | * SYPCR can only be written once after reset! | |
171 | *----------------------------------------------------------------------- | |
172 | * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze | |
173 | */ | |
174 | #if defined(CONFIG_WATCHDOG) | |
6d0f6bcf | 175 | #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \ |
0f8c9768 WD |
176 | SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP) |
177 | #else | |
6d0f6bcf | 178 | #define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP) |
0f8c9768 WD |
179 | #endif |
180 | ||
181 | /*----------------------------------------------------------------------- | |
182 | * SIUMCR - SIU Module Configuration 11-6 | |
183 | *----------------------------------------------------------------------- | |
184 | * PCMCIA config., multi-function pin tri-state | |
185 | */ | |
6d0f6bcf | 186 | #define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01) |
0f8c9768 WD |
187 | |
188 | /*----------------------------------------------------------------------- | |
189 | * TBSCR - Time Base Status and Control 11-26 | |
190 | *----------------------------------------------------------------------- | |
191 | * Clear Reference Interrupt Status, Timebase freezing enabled | |
192 | */ | |
6d0f6bcf | 193 | #define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBE) |
0f8c9768 WD |
194 | |
195 | /*----------------------------------------------------------------------- | |
196 | * PISCR - Periodic Interrupt Status and Control 11-31 | |
197 | *----------------------------------------------------------------------- | |
198 | * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled | |
199 | */ | |
6d0f6bcf | 200 | #define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF) |
0f8c9768 WD |
201 | |
202 | /*----------------------------------------------------------------------- | |
203 | * PLPRCR - PLL, Low-Power, and Reset Control Register 15-30 | |
204 | *----------------------------------------------------------------------- | |
205 | * Reset PLL lock status sticky bit, timer expired status bit and timer * | |
206 | * interrupt status bit - leave PLL multiplication factor unchanged ! | |
207 | */ | |
6d0f6bcf | 208 | #define CONFIG_SYS_PLPRCR (((MPC8XX_FACT-1) << 20) | \ |
0f8c9768 WD |
209 | PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST) |
210 | ||
211 | /*----------------------------------------------------------------------- | |
212 | * SCCR - System Clock and reset Control Register 15-27 | |
213 | *----------------------------------------------------------------------- | |
214 | * Set clock output, timebase and RTC source and divider, | |
215 | * power management and some other internal clocks | |
216 | */ | |
217 | #define SCCR_MASK SCCR_EBDF11 | |
6d0f6bcf | 218 | #define CONFIG_SYS_SCCR (SCCR_TBS | \ |
0f8c9768 WD |
219 | SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \ |
220 | SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \ | |
221 | SCCR_DFALCD00) | |
222 | ||
223 | /*----------------------------------------------------------------------- | |
224 | * | |
225 | *----------------------------------------------------------------------- | |
226 | * | |
227 | */ | |
6d0f6bcf | 228 | #define CONFIG_SYS_DER 0 |
0f8c9768 WD |
229 | |
230 | /* Because of the way the 860 starts up and assigns CS0 the | |
231 | * entire address space, we have to set the memory controller | |
232 | * differently. Normally, you write the option register | |
233 | * first, and then enable the chip select by writing the | |
234 | * base register. For CS0, you must write the base register | |
235 | * first, followed by the option register. | |
236 | */ | |
237 | ||
238 | /* | |
239 | * Init Memory Controller: | |
240 | * | |
241 | * BR0/1 and OR0/1 (FLASH) | |
242 | */ | |
243 | /* the other CS:s are determined by looking at parameters in BCSRx */ | |
244 | ||
245 | ||
246 | #define BCSR_ADDR ((uint) 0x02100000) | |
247 | #define BCSR_SIZE ((uint)(64 * 1024)) | |
248 | ||
249 | #define FLASH_BASE0_PRELIM 0x02800000 /* FLASH bank #0 */ | |
250 | #define FLASH_BASE1_PRELIM 0x00000000 /* FLASH bank #1 */ | |
251 | ||
6d0f6bcf JCPV |
252 | #define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */ |
253 | #define CONFIG_SYS_PRELIM_OR_AM 0xFFE00000 /* OR addr mask */ | |
0f8c9768 WD |
254 | |
255 | /* FLASH timing: ACS = 10, TRLX = 1, CSNT = 1, SCY = 3, EHTR = 0 */ | |
6d0f6bcf | 256 | #define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV4 | OR_BI | OR_SCY_3_CLK | OR_TRLX) |
0f8c9768 | 257 | |
6d0f6bcf JCPV |
258 | #define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) |
259 | #define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH) /* 1 Mbyte until detected and only 1 Mbyte is needed*/ | |
260 | #define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V ) | |
0f8c9768 WD |
261 | |
262 | /* BCSRx - Board Control and Status Registers */ | |
6d0f6bcf JCPV |
263 | #define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP |
264 | #define CONFIG_SYS_OR1_PRELIM 0xffff8110 /* 64Kbyte address space */ | |
265 | #define CONFIG_SYS_BR1_PRELIM ((BCSR_ADDR) | BR_V ) | |
0f8c9768 WD |
266 | |
267 | ||
268 | /* | |
269 | * Memory Periodic Timer Prescaler | |
270 | */ | |
271 | ||
272 | /* periodic timer for refresh */ | |
6d0f6bcf | 273 | #define CONFIG_SYS_MAMR_PTA 97 /* start with divider for 100 MHz */ |
0f8c9768 WD |
274 | |
275 | /* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */ | |
6d0f6bcf JCPV |
276 | #define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */ |
277 | #define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */ | |
0f8c9768 WD |
278 | |
279 | /* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */ | |
6d0f6bcf JCPV |
280 | #define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */ |
281 | #define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */ | |
0f8c9768 WD |
282 | |
283 | /* | |
284 | * MAMR settings for SDRAM | |
285 | */ | |
286 | ||
287 | /* 8 column SDRAM */ | |
6d0f6bcf | 288 | #define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ |
0f8c9768 WD |
289 | MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \ |
290 | MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) | |
291 | /* 9 column SDRAM */ | |
6d0f6bcf | 292 | #define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \ |
0f8c9768 WD |
293 | MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \ |
294 | MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X) | |
295 | ||
6d0f6bcf | 296 | #define CONFIG_SYS_MAMR 0x13a01114 |
0f8c9768 WD |
297 | |
298 | /* values according to the manual */ | |
299 | ||
300 | ||
301 | #define PCMCIA_MEM_ADDR ((uint)0xff020000) | |
302 | #define PCMCIA_MEM_SIZE ((uint)(64 * 1024)) | |
303 | ||
304 | #define BCSR0 ((uint) (BCSR_ADDR + 00)) | |
305 | #define BCSR1 ((uint) (BCSR_ADDR + 0x04)) | |
306 | #define BCSR2 ((uint) (BCSR_ADDR + 0x08)) | |
307 | #define BCSR3 ((uint) (BCSR_ADDR + 0x0c)) | |
308 | #define BCSR4 ((uint) (BCSR_ADDR + 0x10)) | |
309 | ||
310 | /* FADS bitvalues by Helmut Buchsbaum | |
311 | * see MPC8xxADS User's Manual for a proper description | |
312 | * of the following structures | |
313 | */ | |
314 | ||
315 | #define BCSR0_ERB ((uint)0x80000000) | |
316 | #define BCSR0_IP ((uint)0x40000000) | |
317 | #define BCSR0_BDIS ((uint)0x10000000) | |
318 | #define BCSR0_BPS_MASK ((uint)0x0C000000) | |
319 | #define BCSR0_ISB_MASK ((uint)0x01800000) | |
320 | #define BCSR0_DBGC_MASK ((uint)0x00600000) | |
321 | #define BCSR0_DBPC_MASK ((uint)0x00180000) | |
322 | #define BCSR0_EBDF_MASK ((uint)0x00060000) | |
323 | ||
324 | #define BCSR1_FLASH_EN ((uint)0x80000000) | |
325 | #define BCSR1_DRAM_EN ((uint)0x40000000) | |
326 | #define BCSR1_ETHEN ((uint)0x20000000) | |
327 | #define BCSR1_IRDEN ((uint)0x10000000) | |
328 | #define BCSR1_FLASH_CFG_EN ((uint)0x08000000) | |
329 | #define BCSR1_CNT_REG_EN_PROTECT ((uint)0x04000000) | |
330 | #define BCSR1_BCSR_EN ((uint)0x02000000) | |
331 | #define BCSR1_RS232EN_1 ((uint)0x01000000) | |
332 | #define BCSR1_PCCEN ((uint)0x00800000) | |
333 | #define BCSR1_PCCVCC0 ((uint)0x00400000) | |
334 | #define BCSR1_PCCVPP_MASK ((uint)0x00300000) | |
335 | #define BCSR1_DRAM_HALF_WORD ((uint)0x00080000) | |
336 | #define BCSR1_RS232EN_2 ((uint)0x00040000) | |
337 | #define BCSR1_SDRAM_EN ((uint)0x00020000) | |
338 | #define BCSR1_PCCVCC1 ((uint)0x00010000) | |
339 | ||
340 | #define BCSR2_FLASH_PD_MASK ((uint)0xF0000000) | |
b54d32b4 | 341 | #define BCSR2_FLASH_PD_SHIFT 28 |
0f8c9768 | 342 | #define BCSR2_DRAM_PD_MASK ((uint)0x07800000) |
b54d32b4 | 343 | #define BCSR2_DRAM_PD_SHIFT 23 |
0f8c9768 WD |
344 | #define BCSR2_EXTTOLI_MASK ((uint)0x00780000) |
345 | #define BCSR2_DBREVNR_MASK ((uint)0x00030000) | |
346 | ||
347 | #define BCSR3_DBID_MASK ((ushort)0x3800) | |
348 | #define BCSR3_CNT_REG_EN_PROTECT ((ushort)0x0400) | |
349 | #define BCSR3_BREVNR0 ((ushort)0x0080) | |
350 | #define BCSR3_FLASH_PD_MASK ((ushort)0x0070) | |
351 | #define BCSR3_BREVN1 ((ushort)0x0008) | |
352 | #define BCSR3_BREVN2_MASK ((ushort)0x0003) | |
353 | ||
354 | #define BCSR4_ETHLOOP ((uint)0x80000000) | |
355 | #define BCSR4_TFPLDL ((uint)0x40000000) | |
356 | #define BCSR4_TPSQEL ((uint)0x20000000) | |
357 | #define BCSR4_SIGNAL_LAMP ((uint)0x10000000) | |
358 | #ifdef CONFIG_MPC823 | |
359 | #define BCSR4_USB_EN ((uint)0x08000000) | |
360 | #endif /* CONFIG_MPC823 */ | |
361 | #ifdef CONFIG_MPC860SAR | |
362 | #define BCSR4_UTOPIA_EN ((uint)0x08000000) | |
363 | #endif /* CONFIG_MPC860SAR */ | |
364 | #ifdef CONFIG_MPC860T | |
365 | #define BCSR4_FETH_EN ((uint)0x08000000) | |
366 | #endif /* CONFIG_MPC860T */ | |
367 | #ifdef CONFIG_MPC823 | |
368 | #define BCSR4_USB_SPEED ((uint)0x04000000) | |
369 | #endif /* CONFIG_MPC823 */ | |
370 | #ifdef CONFIG_MPC860T | |
371 | #define BCSR4_FETHCFG0 ((uint)0x04000000) | |
372 | #endif /* CONFIG_MPC860T */ | |
373 | #ifdef CONFIG_MPC823 | |
374 | #define BCSR4_VCCO ((uint)0x02000000) | |
375 | #endif /* CONFIG_MPC823 */ | |
376 | #ifdef CONFIG_MPC860T | |
377 | #define BCSR4_FETHFDE ((uint)0x02000000) | |
378 | #endif /* CONFIG_MPC860T */ | |
379 | #ifdef CONFIG_MPC823 | |
380 | #define BCSR4_VIDEO_ON ((uint)0x00800000) | |
381 | #endif /* CONFIG_MPC823 */ | |
382 | #ifdef CONFIG_MPC823 | |
383 | #define BCSR4_VDO_EKT_CLK_EN ((uint)0x00400000) | |
384 | #endif /* CONFIG_MPC823 */ | |
385 | #ifdef CONFIG_MPC860T | |
386 | #define BCSR4_FETHCFG1 ((uint)0x00400000) | |
387 | #endif /* CONFIG_MPC860T */ | |
388 | #ifdef CONFIG_MPC823 | |
389 | #define BCSR4_VIDEO_RST ((uint)0x00200000) | |
390 | #endif /* CONFIG_MPC823 */ | |
391 | #ifdef CONFIG_MPC860T | |
392 | #define BCSR4_FETHRST ((uint)0x00200000) | |
393 | #endif /* CONFIG_MPC860T */ | |
394 | #define BCSR4_MODEM_EN ((uint)0x00100000) | |
395 | #define BCSR4_DATA_VOICE ((uint)0x00080000) | |
396 | ||
397 | #define CONFIG_DRAM_50MHZ 1 | |
398 | #define CONFIG_SDRAM_50MHZ | |
399 | ||
0f8c9768 WD |
400 | /* We don't use the 8259. |
401 | */ | |
402 | #define NR_8259_INTS 0 | |
403 | ||
0f8c9768 WD |
404 | #define CONFIG_DISK_SPINUP_TIME 1000000 |
405 | ||
406 | ||
407 | /* PCMCIA configuration */ | |
408 | ||
409 | #define PCMCIA_MAX_SLOTS 2 | |
410 | ||
411 | #ifdef CONFIG_MPC860 | |
412 | #define PCMCIA_SLOT_A 1 | |
413 | #endif | |
414 | ||
6d0f6bcf | 415 | #define CONFIG_SYS_DAUGHTERBOARD |
180d3f74 | 416 | |
0f8c9768 | 417 | #endif /* __CONFIG_H */ |