[thirdparty/u-boot.git] / include / configs / M5208EVBE.h

/*
 * Configuation settings for the Freescale MCF5208EVBe.
 *
 * Copyright (C) 2004-2008 Freescale Semiconductor, Inc.
 * TsiChung Liew (Tsi-Chung.Liew@freescale.com)
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef _M5208EVBE_H
#define _M5208EVBE_H

/*
 * High Level Configuration Options
 * (easy to change)
 */
#define CONFIG_MCFUART
#define CONFIG_SYS_UART_PORT		(0)
#define CONFIG_BAUDRATE			115200

#undef CONFIG_WATCHDOG
#define CONFIG_WATCHDOG_TIMEOUT		5000

/* Command line configuration */
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_ELF
#undef CONFIG_CMD_I2C
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING
#define CONFIG_CMD_REGINFO

#define CONFIG_MCFFEC
#ifdef CONFIG_MCFFEC
#	define CONFIG_MII		1
#	define CONFIG_MII_INIT		1
#	define CONFIG_SYS_DISCOVER_PHY
#	define CONFIG_SYS_RX_ETH_BUFFER	8
#	define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
#	define CONFIG_HAS_ETH1

#	define CONFIG_SYS_FEC0_PINMUX	0
#	define CONFIG_SYS_FEC0_MIIBASE	CONFIG_SYS_FEC0_IOBASE
#	define MCFFEC_TOUT_LOOP		50000
/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
#	ifndef CONFIG_SYS_DISCOVER_PHY
#		define FECDUPLEX	FULL
#		define FECSPEED		_100BASET
#	else
#		ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
#			define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
#		endif
#	endif			/* CONFIG_SYS_DISCOVER_PHY */
#endif

/* Timer */
#define CONFIG_MCFTMR
#undef CONFIG_MCFPIT

/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED	80000
#define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET	0x58000
#define CONFIG_SYS_IMMR			CONFIG_SYS_MBAR

#define CONFIG_BOOTDELAY		1	/* autoboot after 5 seconds */
#define CONFIG_UDP_CHECKSUM

#ifdef CONFIG_MCFFEC
#	define CONFIG_IPADDR	192.162.1.2
#	define CONFIG_NETMASK	255.255.255.0
#	define CONFIG_SERVERIP	192.162.1.1
#	define CONFIG_GATEWAYIP	192.162.1.1
#endif				/* CONFIG_MCFFEC */

#define CONFIG_HOSTNAME		M5208EVBe
#define CONFIG_EXTRA_ENV_SETTINGS		\
	"netdev=eth0\0"				\
	"loadaddr=40010000\0"			\
	"u-boot=u-boot.bin\0"			\
	"load=tftp ${loadaddr) ${u-boot}\0"	\
	"upd=run load; run prog\0"		\
	"prog=prot off 0 3ffff;"		\
	"era 0 3ffff;"				\
	"cp.b ${loadaddr} 0 ${filesize};"	\
	"save\0"				\
	""

#define CONFIG_PRAM		512	/* 512 KB */
#define CONFIG_SYS_PROMPT	"-> "
#define CONFIG_SYS_LONGHELP	/* undef to save memory */

#ifdef CONFIG_CMD_KGDB
#	define CONFIG_SYS_CBSIZE	1024	/* Console I/O Buffer Size */
#else
#	define CONFIG_SYS_CBSIZE	256	/* Console I/O Buffer Size */
#endif

#define CONFIG_SYS_PBSIZE	(CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
#define CONFIG_SYS_MAXARGS	16		/* max number of cmd args */
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Arg Buf Sz */
#define CONFIG_SYS_LOAD_ADDR	0x40010000

#define CONFIG_SYS_CLK		166666666	/* CPU Core Clock */
#define CONFIG_SYS_PLL_ODR	0x36
#define CONFIG_SYS_PLL_FDR	0x7D

#define CONFIG_SYS_MBAR		0xFC000000

/*
 * Low Level Configuration Settings
 * (address mappings, register initial values, etc.)
 * You should know what you are doing if you make changes here.
 */
/* Definitions for initial stack pointer and data area (in DPRAM) */
#define CONFIG_SYS_INIT_RAM_ADDR	0x80000000
#define CONFIG_SYS_INIT_RAM_SIZE		0x4000	/* Size of used area in internal SRAM */
#define CONFIG_SYS_INIT_RAM_CTRL	0x221
#define CONFIG_SYS_GBL_DATA_OFFSET	((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10)
#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

/*
 * Start addresses for the final memory configuration
 * (Set up by the startup code)
 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 */
#define CONFIG_SYS_SDRAM_BASE		0x40000000
#define CONFIG_SYS_SDRAM_SIZE		32	/* SDRAM size in MB */
#define CONFIG_SYS_SDRAM_CFG1		0x43711630
#define CONFIG_SYS_SDRAM_CFG2		0x56670000
#define CONFIG_SYS_SDRAM_CTRL		0xE1002000
#define CONFIG_SYS_SDRAM_EMOD		0x80010000
#define CONFIG_SYS_SDRAM_MODE		0x00CD0000

#define CONFIG_SYS_MEMTEST_START	CONFIG_SYS_SDRAM_BASE + 0x400
#define CONFIG_SYS_MEMTEST_END		((CONFIG_SYS_SDRAM_SIZE - 3) << 20)

#define CONFIG_SYS_MONITOR_BASE		(CONFIG_SYS_FLASH_BASE + 0x400)
#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor */

#define CONFIG_SYS_BOOTPARAMS_LEN	64*1024
#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc() */

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization ??
 */
#define CONFIG_SYS_BOOTMAPSZ		(CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
#define CONFIG_SYS_BOOTM_LEN		(CONFIG_SYS_SDRAM_SIZE << 20)

/* FLASH organization */
#define CONFIG_SYS_FLASH_CFI
#ifdef CONFIG_SYS_FLASH_CFI
#	define CONFIG_FLASH_CFI_DRIVER		1
#	define CONFIG_SYS_FLASH_SIZE		0x800000	/* Max size that the board might have */
#	define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_16BIT
#	define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
#	define CONFIG_SYS_MAX_FLASH_SECT	254	/* max number of sectors on one chip */
#	define CONFIG_SYS_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */
#endif

#define CONFIG_SYS_FLASH_BASE		CONFIG_SYS_CS0_BASE

/*
 * Configuration for environment
 * Environment is embedded in u-boot in the second sector of the flash
 */
#define CONFIG_ENV_OFFSET		0x2000
#define CONFIG_ENV_SIZE			0x1000
#define CONFIG_ENV_SECT_SIZE		0x2000
#define CONFIG_ENV_IS_IN_FLASH		1

#define LDS_BOARD_TEXT \
        . = DEFINED(env_offset) ? env_offset : .; \
        common/env_embedded.o (.text*);

/* Cache Configuration */
#define CONFIG_SYS_CACHELINE_SIZE	16

#define ICACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
					 CONFIG_SYS_INIT_RAM_SIZE - 8)
#define DCACHE_STATUS			(CONFIG_SYS_INIT_RAM_ADDR + \
					 CONFIG_SYS_INIT_RAM_SIZE - 4)
#define CONFIG_SYS_ICACHE_INV		(CF_CACR_CINV | CF_CACR_INVI)
#define CONFIG_SYS_CACHE_ACR0		(CONFIG_SYS_SDRAM_BASE | \
					 CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
					 CF_ACR_EN | CF_ACR_SM_ALL)
#define CONFIG_SYS_CACHE_ICACR		(CF_CACR_CENB | CF_CACR_CINV | \
					 CF_CACR_DISD | CF_CACR_INVI | \
					 CF_CACR_CEIB | CF_CACR_DCM | \
					 CF_CACR_EUSP)

/* Chipselect bank definitions */
/*
 * CS0 - NOR Flash
 * CS1 - Available
 * CS2 - Available
 * CS3 - Available
 * CS4 - Available
 * CS5 - Available
 */
#define CONFIG_SYS_CS0_BASE		0
#define CONFIG_SYS_CS0_MASK		0x007F0001
#define CONFIG_SYS_CS0_CTRL		0x00001FA0

#endif				/* _M5208EVBE_H */
Commit	Line	Data
bf9a5215 TL	1	/*
	2	* Configuation settings for the Freescale MCF5208EVBe.
	3	*
	4	* Copyright (C) 2004-2008 Freescale Semiconductor, Inc.
	5	* TsiChung Liew (Tsi-Chung.Liew@freescale.com)
	6	*
3765b3e7	7	* SPDX-License-Identifier: GPL-2.0+
bf9a5215 TL	8	*/
	9
	10	#ifndef _M5208EVBE_H
	11	#define _M5208EVBE_H
	12
	13	/*
	14	* High Level Configuration Options
	15	* (easy to change)
	16	*/
bf9a5215 TL	17	#define CONFIG_MCFUART
	18	#define CONFIG_SYS_UART_PORT (0)
	19	#define CONFIG_BAUDRATE 115200
bf9a5215 TL	20
	21	#undef CONFIG_WATCHDOG
	22	#define CONFIG_WATCHDOG_TIMEOUT 5000
	23
	24	/* Command line configuration */
bf9a5215 TL	25	#define CONFIG_CMD_CACHE
bf9a5215 TL	26	#define CONFIG_CMD_ELF
bf9a5215	27	#undef CONFIG_CMD_I2C
bf9a5215	28	#define CONFIG_CMD_MII
bf9a5215 TL	29	#define CONFIG_CMD_PING
	30	#define CONFIG_CMD_REGINFO
	31
	32	#define CONFIG_MCFFEC
	33	#ifdef CONFIG_MCFFEC
bf9a5215 TL	34	# define CONFIG_MII 1
	35	# define CONFIG_MII_INIT 1
	36	# define CONFIG_SYS_DISCOVER_PHY
	37	# define CONFIG_SYS_RX_ETH_BUFFER 8
	38	# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
	39	# define CONFIG_HAS_ETH1
	40
	41	# define CONFIG_SYS_FEC0_PINMUX 0
	42	# define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE
	43	# define MCFFEC_TOUT_LOOP 50000
	44	/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
	45	# ifndef CONFIG_SYS_DISCOVER_PHY
	46	# define FECDUPLEX FULL
	47	# define FECSPEED _100BASET
	48	# else
	49	# ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
	50	# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
	51	# endif
	52	# endif /* CONFIG_SYS_DISCOVER_PHY */
	53	#endif
	54
	55	/* Timer */
	56	#define CONFIG_MCFTMR
	57	#undef CONFIG_MCFPIT
	58
	59	/* I2C */
00f792e0 HS	60	#define CONFIG_SYS_I2C
	61	#define CONFIG_SYS_I2C_FSL
	62	#define CONFIG_SYS_FSL_I2C_SPEED 80000
	63	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	64	#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000
bf9a5215 TL	65	#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
	66
	67	#define CONFIG_BOOTDELAY 1 /* autoboot after 5 seconds */
	68	#define CONFIG_UDP_CHECKSUM
	69
	70	#ifdef CONFIG_MCFFEC
bf9a5215 TL	71	# define CONFIG_IPADDR 192.162.1.2
	72	# define CONFIG_NETMASK 255.255.255.0
	73	# define CONFIG_SERVERIP 192.162.1.1
	74	# define CONFIG_GATEWAYIP 192.162.1.1
bf9a5215 TL	75	#endif /* CONFIG_MCFFEC */
	76
	77	#define CONFIG_HOSTNAME M5208EVBe
	78	#define CONFIG_EXTRA_ENV_SETTINGS \
	79	"netdev=eth0\0" \
	80	"loadaddr=40010000\0" \
	81	"u-boot=u-boot.bin\0" \
	82	"load=tftp ${loadaddr) ${u-boot}\0" \
	83	"upd=run load; run prog\0" \
	84	"prog=prot off 0 3ffff;" \
	85	"era 0 3ffff;" \
	86	"cp.b ${loadaddr} 0 ${filesize};" \
	87	"save\0" \
	88	""
	89
	90	#define CONFIG_PRAM 512 /* 512 KB */
	91	#define CONFIG_SYS_PROMPT "-> "
	92	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	93
	94	#ifdef CONFIG_CMD_KGDB
	95	# define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	96	#else
	97	# define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	98	#endif
	99
	100	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	101	#define CONFIG_SYS_MAXARGS 16 /* max number of cmd args */
	102	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Arg Buf Sz */
	103	#define CONFIG_SYS_LOAD_ADDR 0x40010000
	104
bf9a5215 TL	105	#define CONFIG_SYS_CLK 166666666 /* CPU Core Clock */
	106	#define CONFIG_SYS_PLL_ODR 0x36
	107	#define CONFIG_SYS_PLL_FDR 0x7D
	108
	109	#define CONFIG_SYS_MBAR 0xFC000000
	110
	111	/*
	112	* Low Level Configuration Settings
	113	* (address mappings, register initial values, etc.)
	114	* You should know what you are doing if you make changes here.
	115	*/
	116	/* Definitions for initial stack pointer and data area (in DPRAM) */
	117	#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000
553f0982	118	#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in internal SRAM */
bf9a5215	119	#define CONFIG_SYS_INIT_RAM_CTRL 0x221
25ddd1fb	120	#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 0x10)
bf9a5215 TL	121	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
	122
	123	/*
	124	* Start addresses for the final memory configuration
	125	* (Set up by the startup code)
	126	* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
	127	*/
	128	#define CONFIG_SYS_SDRAM_BASE 0x40000000
f628e2f7	129	#define CONFIG_SYS_SDRAM_SIZE 32 /* SDRAM size in MB */
bf9a5215 TL	130	#define CONFIG_SYS_SDRAM_CFG1 0x43711630
	131	#define CONFIG_SYS_SDRAM_CFG2 0x56670000
	132	#define CONFIG_SYS_SDRAM_CTRL 0xE1002000
	133	#define CONFIG_SYS_SDRAM_EMOD 0x80010000
	134	#define CONFIG_SYS_SDRAM_MODE 0x00CD0000
	135
	136	#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE + 0x400
	137	#define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20)
	138
	139	#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
	140	#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
	141
	142	#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024
	143	#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
	144
	145	/*
	146	* For booting Linux, the board info and command line data
	147	* have to be in the first 8 MB of memory, since this is
	148	* the maximum mapped by the Linux kernel during initialization ??
	149	*/
	150	#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
	151	#define CONFIG_SYS_BOOTM_LEN (CONFIG_SYS_SDRAM_SIZE << 20)
	152
	153	/* FLASH organization */
	154	#define CONFIG_SYS_FLASH_CFI
	155	#ifdef CONFIG_SYS_FLASH_CFI
	156	# define CONFIG_FLASH_CFI_DRIVER 1
	157	# define CONFIG_SYS_FLASH_SIZE 0x800000 /* Max size that the board might have */
	158	# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
	159	# define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
	160	# define CONFIG_SYS_MAX_FLASH_SECT 254 /* max number of sectors on one chip */
	161	# define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */
	162	#endif
	163
	164	#define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE
	165
	166	/*
	167	* Configuration for environment
	168	* Environment is embedded in u-boot in the second sector of the flash
	169	*/
	170	#define CONFIG_ENV_OFFSET 0x2000
	171	#define CONFIG_ENV_SIZE 0x1000
	172	#define CONFIG_ENV_SECT_SIZE 0x2000
	173	#define CONFIG_ENV_IS_IN_FLASH 1
	174
5296cb1d	175	#define LDS_BOARD_TEXT \
	176	. = DEFINED(env_offset) ? env_offset : .; \
	177	common/env_embedded.o (.text*);
	178
bf9a5215 TL	179	/* Cache Configuration */
	180	#define CONFIG_SYS_CACHELINE_SIZE 16
	181
dd9f054e	182	#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
553f0982	183	CONFIG_SYS_INIT_RAM_SIZE - 8)
dd9f054e	184	#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
553f0982	185	CONFIG_SYS_INIT_RAM_SIZE - 4)
dd9f054e TL	186	#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV \| CF_CACR_INVI)
	187	#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE \| \
	188	CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) \| \
	189	CF_ACR_EN \| CF_ACR_SM_ALL)
	190	#define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB \| CF_CACR_CINV \| \
	191	CF_CACR_DISD \| CF_CACR_INVI \| \
	192	CF_CACR_CEIB \| CF_CACR_DCM \| \
	193	CF_CACR_EUSP)
	194
bf9a5215 TL	195	/* Chipselect bank definitions */
	196	/*
	197	* CS0 - NOR Flash
	198	* CS1 - Available
	199	* CS2 - Available
	200	* CS3 - Available
	201	* CS4 - Available
	202	* CS5 - Available
	203	*/
	204	#define CONFIG_SYS_CS0_BASE 0
	205	#define CONFIG_SYS_CS0_MASK 0x007F0001
	206	#define CONFIG_SYS_CS0_CTRL 0x00001FA0
	207
	208	#endif /* _M5208EVBE_H */