]> git.ipfire.org Git - people/ms/u-boot.git/blame - include/configs/MPC8610HPCD.h
86xx: Add reginfo command
[people/ms/u-boot.git] / include / configs / MPC8610HPCD.h
CommitLineData
9553df86
JL
1/*
2 * Copyright 2007 Freescale Semiconductor, Inc.
3 *
4 * This program is free software; you can redistribute it and/or
5 * modify it under the terms of the GNU General Public License
6 * Version 2 as published by the Free Software Foundation.
7 */
8
9/*
10 * MPC8610HPCD board configuration file
11 *
12 */
13
14#ifndef __CONFIG_H
15#define __CONFIG_H
16
17/* High Level Configuration Options */
18#define CONFIG_MPC86xx 1 /* MPC86xx */
19#define CONFIG_MPC8610 1 /* MPC8610 specific */
20#define CONFIG_MPC8610HPCD 1 /* MPC8610HPCD board specific */
21#define CONFIG_NUM_CPUS 1 /* Number of CPUs in the system */
22#define CONFIG_LINUX_RESET_VEC 0x100 /* Reset vector used by Linux */
23
a877880c 24#define CONFIG_FSL_DIU_FB 1 /* FSL DIU */
070ba561
YS
25
26/* video */
68b88999 27#define CONFIG_VIDEO
070ba561
YS
28
29#if defined(CONFIG_VIDEO)
30#define CONFIG_CFB_CONSOLE
31#define CONFIG_VGA_AS_SINGLE_DEVICE
32#endif
33
9553df86
JL
34#ifdef RUN_DIAG
35#define CFG_DIAG_ADDR 0xff800000
36#endif
37
38#define CFG_RESET_ADDRESS 0xfff00100
39
40#define CONFIG_PCI 1 /* Enable PCI/PCIE*/
41#define CONFIG_PCI1 1 /* PCI controler 1 */
42#define CONFIG_PCIE1 1 /* PCIe 1 connected to ULI bridge */
43#define CONFIG_PCIE2 1 /* PCIe 2 connected to slot */
44#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
031976f6 45#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
9553df86
JL
46
47#define CONFIG_ENV_OVERWRITE
48
49#define CONFIG_SPD_EEPROM /* Use SPD for DDR */
50#undef CONFIG_DDR_DLL /* possible DLL fix needed */
51#define CONFIG_DDR_2T_TIMING /* Sets the 2T timing bit */
a877880c 52#undef CONFIG_DDR_ECC /* only for ECC DDR module */
9553df86
JL
53#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER /* DDR controller or DMA? */
54#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
55#define CONFIG_NUM_DDR_CONTROLLERS 1
56#define CONFIG_INTERRUPTS /* enable pci, srio, ddr interrupts */
57
58#define CONFIG_ALTIVEC 1
59
60/*
61 * L2CR setup -- make sure this is right for your board!
62 */
63#define CFG_L2
64#define L2_INIT 0
a877880c 65#define L2_ENABLE (L2CR_L2E |0x00100000 )
9553df86
JL
66
67#ifndef CONFIG_SYS_CLK_FREQ
68#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
69#endif
70
71#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_pre_init */
a877880c 72#define CONFIG_MISC_INIT_R 1
9553df86
JL
73
74#undef CFG_DRAM_TEST /* memory test, takes time */
75#define CFG_MEMTEST_START 0x00200000 /* memtest region */
76#define CFG_MEMTEST_END 0x00400000
77#define CFG_ALT_MEMTEST
78
79/*
80 * Base addresses -- Note these are effective addresses where the
81 * actual resources get mapped (not physical addresses)
82 */
83#define CFG_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
84#define CFG_CCSRBAR 0xe0000000 /* relocated CCSRBAR */
85#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
86
87#define CFG_PCI1_ADDR (CFG_CCSRBAR+0x8000)
88#define CFG_PCIE1_ADDR (CFG_CCSRBAR+0xa000)
89#define CFG_PCIE2_ADDR (CFG_CCSRBAR+0x9000)
90
91#define CFG_DIU_ADDR (CFG_CCSRBAR+0x2c000)
92
93/*
94 * DDR Setup
95 */
96#define CFG_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
97#define CFG_SDRAM_BASE CFG_DDR_SDRAM_BASE
98#define CONFIG_VERY_BIG_RAM
99
100#define MPC86xx_DDR_SDRAM_CLK_CNTL
101
102#if defined(CONFIG_SPD_EEPROM)
103/*
104 * Determine DDR configuration from I2C interface.
105 */
106#define SPD_EEPROM_ADDRESS1 0x51 /* DDR DIMM */
107#else
108/*
109 * Manually set up DDR1 parameters
110 */
111
112#define CFG_SDRAM_SIZE 256 /* DDR is 256MB */
113
114#if 0 /* TODO */
115#define CFG_DDR_CS0_BNDS 0x0000000F
116#define CFG_DDR_CS0_CONFIG 0x80010202 /* Enable, no interleaving */
117#define CFG_DDR_EXT_REFRESH 0x00000000
118#define CFG_DDR_TIMING_0 0x00260802
119#define CFG_DDR_TIMING_1 0x3935d322
120#define CFG_DDR_TIMING_2 0x14904cc8
121#define CFG_DDR_MODE_1 0x00480432
122#define CFG_DDR_MODE_2 0x00000000
123#define CFG_DDR_INTERVAL 0x06180100
124#define CFG_DDR_DATA_INIT 0xdeadbeef
125#define CFG_DDR_CLK_CTRL 0x03800000
126#define CFG_DDR_OCD_CTRL 0x00000000
127#define CFG_DDR_OCD_STATUS 0x00000000
128#define CFG_DDR_CONTROL 0xe3008000 /* Type = DDR2 */
129#define CFG_DDR_CONTROL2 0x04400010
130
131#define CFG_DDR_ERR_INT_EN 0x00000000
132#define CFG_DDR_ERR_DIS 0x00000000
133#define CFG_DDR_SBE 0x000f0000
134 /* Not used in fixed_sdram function */
135#define CFG_DDR_MODE 0x00000022
136#define CFG_DDR_CS1_BNDS 0x00000000
137#define CFG_DDR_CS2_BNDS 0x00000FFF /* Not done */
138#define CFG_DDR_CS3_BNDS 0x00000FFF /* Not done */
139#define CFG_DDR_CS4_BNDS 0x00000FFF /* Not done */
140#define CFG_DDR_CS5_BNDS 0x00000FFF /* Not done */
141#endif
142#endif
143
144#define CFG_ID_EEPROM
ad8f8687
JL
145#ifdef CFG_ID_EEPROM
146#define CONFIG_ID_EEPROM
147#endif
9553df86
JL
148#define ID_EEPROM_ADDR 0x57
149
150
151#define CFG_FLASH_BASE 0xf0000000 /* start of FLASH 128M */
152#define CFG_FLASH_BASE2 0xf8000000
153
154#define CFG_FLASH_BANKS_LIST {CFG_FLASH_BASE, CFG_FLASH_BASE2}
155
156#define CFG_BR0_PRELIM 0xf8001001 /* port size 16bit */
157#define CFG_OR0_PRELIM 0xf8006e65 /* 128MB NOR Flash*/
158
159#define CFG_BR1_PRELIM 0xf0001001 /* port size 16bit */
160#define CFG_OR1_PRELIM 0xf8006e65 /* 128MB Promjet */
161#if 0 /* TODO */
162#define CFG_BR2_PRELIM 0xf0000000
163#define CFG_OR2_PRELIM 0xf0000000 /* 256MB NAND Flash - bank 1 */
164#endif
165#define CFG_BR3_PRELIM 0xe8000801 /* port size 8bit */
166#define CFG_OR3_PRELIM 0xfff06ff7 /* 1MB PIXIS area*/
167
168
761421cc 169#define CONFIG_FSL_PIXIS 1 /* use common PIXIS code */
9553df86
JL
170#define PIXIS_BASE 0xe8000000 /* PIXIS registers */
171#define PIXIS_ID 0x0 /* Board ID at offset 0 */
172#define PIXIS_VER 0x1 /* Board version at offset 1 */
173#define PIXIS_PVER 0x2 /* PIXIS FPGA version at offset 2 */
174#define PIXIS_RST 0x4 /* PIXIS Reset Control register */
175#define PIXIS_AUX 0x6 /* PIXIS Auxiliary register; Scratch */
176#define PIXIS_SPD 0x7 /* Register for SYSCLK speed */
a877880c 177#define PIXIS_BRDCFG0 0x8 /* PIXIS Board Configuration Register0*/
9553df86
JL
178#define PIXIS_VCTL 0x10 /* VELA Control Register */
179#define PIXIS_VCFGEN0 0x12 /* VELA Config Enable 0 */
180#define PIXIS_VCFGEN1 0x13 /* VELA Config Enable 1 */
181#define PIXIS_VBOOT 0x16 /* VELA VBOOT Register */
182#define PIXIS_VSPEED0 0x17 /* VELA VSpeed 0 */
183#define PIXIS_VSPEED1 0x18 /* VELA VSpeed 1 */
184#define PIXIS_VCLKH 0x19 /* VELA VCLKH register */
185#define PIXIS_VCLKL 0x1A /* VELA VCLKL register */
761421cc 186#define CFG_PIXIS_VBOOT_MASK 0x0C /* Reset altbank mask*/
9553df86
JL
187
188#define CFG_MAX_FLASH_BANKS 2 /* number of banks */
189#define CFG_MAX_FLASH_SECT 1024 /* sectors per device */
190
191#undef CFG_FLASH_CHECKSUM
192#define CFG_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
193#define CFG_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
194#define CFG_MONITOR_BASE TEXT_BASE /* start of monitor */
195
196#define CFG_FLASH_CFI_DRIVER
197#define CFG_FLASH_CFI
198#define CFG_FLASH_EMPTY_INFO
199
200#if (CFG_MONITOR_BASE < CFG_FLASH_BASE)
201#define CFG_RAMBOOT
202#else
203#undef CFG_RAMBOOT
204#endif
205
206#if defined(CFG_RAMBOOT)
207#undef CONFIG_SPD_EEPROM
208#define CFG_SDRAM_SIZE 256
209#endif
210
211#undef CONFIG_CLOCKS_IN_MHZ
212
213#define CONFIG_L1_INIT_RAM
214#define CFG_INIT_RAM_LOCK 1
215#ifndef CFG_INIT_RAM_LOCK
216#define CFG_INIT_RAM_ADDR 0xe4010000 /* Initial RAM address */
217#else
218#define CFG_INIT_RAM_ADDR 0xe4000000 /* Initial RAM address */
219#endif
220#define CFG_INIT_RAM_END 0x4000 /* End of used area in RAM */
221
222#define CFG_GBL_DATA_SIZE 128 /* num bytes initial data */
223#define CFG_GBL_DATA_OFFSET (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
224#define CFG_INIT_SP_OFFSET CFG_GBL_DATA_OFFSET
225
226#define CFG_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */
a877880c 227#define CFG_MALLOC_LEN (6 * 1024 * 1024) /* Reserved for malloc */
9553df86
JL
228
229/* Serial Port */
230#define CONFIG_CONS_INDEX 1
231#undef CONFIG_SERIAL_SOFTWARE_FIFO
232#define CFG_NS16550
233#define CFG_NS16550_SERIAL
234#define CFG_NS16550_REG_SIZE 1
235#define CFG_NS16550_CLK get_bus_freq(0)
236
237#define CFG_BAUDRATE_TABLE \
238 {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
239
240#define CFG_NS16550_COM1 (CFG_CCSRBAR+0x4500)
241#define CFG_NS16550_COM2 (CFG_CCSRBAR+0x4600)
242
243/* Use the HUSH parser */
244#define CFG_HUSH_PARSER
245#ifdef CFG_HUSH_PARSER
246#define CFG_PROMPT_HUSH_PS2 "> "
247#endif
248
249/*
250 * Pass open firmware flat tree to kernel
251 */
1df170f8
JL
252#define CONFIG_OF_LIBFDT 1
253#define CONFIG_OF_BOARD_SETUP 1
254#define CONFIG_OF_STDOUT_VIA_ALIAS 1
255
9553df86
JL
256
257/* maximum size of the flat tree (8K) */
258#define OF_FLAT_TREE_MAX_SIZE 8192
259
9553df86
JL
260#define CFG_64BIT_VSPRINTF 1
261#define CFG_64BIT_STRTOUL 1
262
263/*
264 * I2C
265 */
266#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
267#define CONFIG_HARD_I2C /* I2C with hardware support*/
268#undef CONFIG_SOFT_I2C /* I2C bit-banged */
269#define CFG_I2C_SPEED 400000 /* I2C speed and slave address */
270#define CFG_I2C_SLAVE 0x7F
271#define CFG_I2C_NOPROBES {0x69} /* Don't probe these addrs */
272#define CFG_I2C_OFFSET 0x3000
273
274/*
275 * General PCI
276 * Addresses are mapped 1-1.
277 */
278#define CFG_PCI1_MEM_BASE 0x80000000
279#define CFG_PCI1_MEM_PHYS CFG_PCI1_MEM_BASE
280#define CFG_PCI1_MEM_SIZE 0x10000000 /* 256M */
281#define CFG_PCI1_IO_BASE 0x00000000
282#define CFG_PCI1_IO_PHYS 0xe1000000
283#define CFG_PCI1_IO_SIZE 0x00100000 /* 1M */
284
285/* PCI view of System Memory */
286#define CFG_PCI_MEMORY_BUS 0x00000000
287#define CFG_PCI_MEMORY_PHYS 0x00000000
288#define CFG_PCI_MEMORY_SIZE 0x80000000
289
290/* For RTL8139 */
291#define KSEG1ADDR(x) ({u32 _x = le32_to_cpu(*(u32 *)(x)); (&_x); })
292#define _IO_BASE 0x00000000
293
294/* controller 1, Base address 0xa000 */
295#define CFG_PCIE1_MEM_BASE 0xa0000000
296#define CFG_PCIE1_MEM_PHYS CFG_PCIE1_MEM_BASE
297#define CFG_PCIE1_MEM_SIZE 0x10000000 /* 256M */
298#define CFG_PCIE1_IO_BASE 0x00000000
299#define CFG_PCIE1_IO_PHYS 0xe3000000
300#define CFG_PCIE1_IO_SIZE 0x00100000 /* 1M */
301
302/* controller 2, Base Address 0x9000 */
303#define CFG_PCIE2_MEM_BASE 0x90000000
304#define CFG_PCIE2_MEM_PHYS CFG_PCIE2_MEM_BASE
305#define CFG_PCIE2_MEM_SIZE 0x10000000 /* 256M */
306#define CFG_PCIE2_IO_BASE 0x00000000 /* reuse mem LAW */
307#define CFG_PCIE2_IO_PHYS 0xe2000000
308#define CFG_PCIE2_IO_SIZE 0x00100000 /* 1M */
309
310
311#if defined(CONFIG_PCI)
312
313#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
314
315#define CONFIG_NET_MULTI
1d8a49ec 316#define CONFIG_CMD_NET
9553df86 317#define CONFIG_PCI_PNP /* do pci plug-and-play */
4f93f8b1 318#define CONFIG_CMD_REGINFO
9553df86 319
7c2221eb
RZ
320#define CONFIG_ULI526X
321#ifdef CONFIG_ULI526X
1d8a49ec
RZ
322#define CONFIG_ETHADDR 00:E0:0C:00:00:01
323#endif
9553df86 324
9553df86
JL
325/************************************************************
326 * USB support
327 ************************************************************/
070ba561
YS
328#define CONFIG_PCI_OHCI 1
329#define CONFIG_USB_OHCI_NEW 1
9553df86
JL
330#define CONFIG_USB_KEYBOARD 1
331#define CFG_DEVICE_DEREGISTER
070ba561
YS
332#define CFG_USB_EVENT_POLL 1
333#define CFG_USB_OHCI_SLOT_NAME "ohci_pci"
334#define CFG_USB_OHCI_MAX_ROOT_PORTS 15
335#define CFG_OHCI_SWAP_REG_ACCESS 1
9553df86
JL
336
337#if !defined(CONFIG_PCI_PNP)
338#define PCI_ENET0_IOADDR 0xe0000000
339#define PCI_ENET0_MEMADDR 0xe0000000
340#define PCI_IDSEL_NUMBER 0x0c /* slot0->3(IDSEL)=12->15 */
341#endif
342
343#define CONFIG_DOS_PARTITION
344#define CONFIG_SCSI_AHCI
345
346#ifdef CONFIG_SCSI_AHCI
347#define CONFIG_SATA_ULI5288
348#define CFG_SCSI_MAX_SCSI_ID 4
349#define CFG_SCSI_MAX_LUN 1
350#define CFG_SCSI_MAX_DEVICE (CFG_SCSI_MAX_SCSI_ID * CFG_SCSI_MAX_LUN)
351#define CFG_SCSI_MAXDEVICE CFG_SCSI_MAX_DEVICE
352#endif
353
354#endif /* CONFIG_PCI */
355
356/*
357 * BAT0 2G Cacheable, non-guarded
358 * 0x0000_0000 2G DDR
359 */
360#define CFG_DBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE)
361#define CFG_DBAT0U (BATU_BL_2G | BATU_VS | BATU_VP)
362#define CFG_IBAT0L (BATL_PP_RW | BATL_MEMCOHERENCE )
363#define CFG_IBAT0U CFG_DBAT0U
364
365/*
366 * BAT1 1G Cache-inhibited, guarded
367 * 0x8000_0000 256M PCI-1 Memory
368 * 0xa000_0000 256M PCI-Express 1 Memory
369 * 0x9000_0000 256M PCI-Express 2 Memory
370 */
371
372#define CFG_DBAT1L (CFG_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
373 | BATL_GUARDEDSTORAGE)
374#define CFG_DBAT1U (CFG_PCI1_MEM_PHYS | BATU_BL_1G | BATU_VS | BATU_VP)
375#define CFG_IBAT1L (CFG_PCI1_MEM_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
376#define CFG_IBAT1U CFG_DBAT1U
377
378/*
f3bceaab 379 * BAT2 16M Cache-inhibited, guarded
9553df86 380 * 0xe100_0000 1M PCI-1 I/O
9553df86
JL
381 */
382
383#define CFG_DBAT2L (CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
384 | BATL_GUARDEDSTORAGE)
f3bceaab 385#define CFG_DBAT2U (CFG_PCI1_IO_PHYS | BATU_BL_16M | BATU_VS | BATU_VP)
9553df86
JL
386#define CFG_IBAT2L (CFG_PCI1_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
387#define CFG_IBAT2U CFG_DBAT2U
388
389/*
f3bceaab
JJ
390 * BAT3 32M Cache-inhibited, guarded
391 * 0xe200_0000 1M PCI-Express 2 I/O
9553df86 392 * 0xe300_0000 1M PCI-Express 1 I/O
9553df86
JL
393 */
394
f3bceaab 395#define CFG_DBAT3L (CFG_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT \
9553df86 396 | BATL_GUARDEDSTORAGE)
f3bceaab
JJ
397#define CFG_DBAT3U (CFG_PCIE2_IO_PHYS | BATU_BL_32M | BATU_VS | BATU_VP)
398#define CFG_IBAT3L (CFG_PCIE2_IO_PHYS | BATL_PP_RW | BATL_CACHEINHIBIT)
9553df86
JL
399#define CFG_IBAT3U CFG_DBAT3U
400
401/*
402 * BAT4 4M Cache-inhibited, guarded
403 * 0xe000_0000 4M CCSR
404 */
405#define CFG_DBAT4L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT \
406 | BATL_GUARDEDSTORAGE)
407#define CFG_DBAT4U (CFG_CCSRBAR | BATU_BL_1M | BATU_VS | BATU_VP)
408#define CFG_IBAT4L (CFG_CCSRBAR | BATL_PP_RW | BATL_CACHEINHIBIT)
409#define CFG_IBAT4U CFG_DBAT4U
410
411/*
412 * BAT5 128K Cacheable, non-guarded
413 * 0xe400_0000 128K Init RAM for stack in the CPU DCache (no backing memory)
414 */
415#define CFG_DBAT5L (CFG_INIT_RAM_ADDR | BATL_PP_RW | BATL_MEMCOHERENCE)
416#define CFG_DBAT5U (CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
417#define CFG_IBAT5L CFG_DBAT5L
418#define CFG_IBAT5U CFG_DBAT5U
419
420/*
421 * BAT6 256M Cache-inhibited, guarded
422 * 0xf000_0000 256M FLASH
423 */
424#define CFG_DBAT6L (CFG_FLASH_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \
425 | BATL_GUARDEDSTORAGE)
426#define CFG_DBAT6U (CFG_FLASH_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
427#define CFG_IBAT6L (CFG_FLASH_BASE | BATL_PP_RW | BATL_MEMCOHERENCE)
428#define CFG_IBAT6U CFG_DBAT6U
429
430/*
431 * BAT7 4M Cache-inhibited, guarded
432 * 0xe800_0000 4M PIXIS
433 */
434#define CFG_DBAT7L (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT \
435 | BATL_GUARDEDSTORAGE)
436#define CFG_DBAT7U (PIXIS_BASE | BATU_BL_1M | BATU_VS | BATU_VP)
437#define CFG_IBAT7L (PIXIS_BASE | BATL_PP_RW | BATL_CACHEINHIBIT)
438#define CFG_IBAT7U CFG_DBAT7U
439
440
441/*
442 * Environment
443 */
444#ifndef CFG_RAMBOOT
445#define CFG_ENV_IS_IN_FLASH 1
446#define CFG_ENV_ADDR (CFG_MONITOR_BASE + CFG_MONITOR_LEN)
447#define CFG_ENV_SECT_SIZE 0x20000 /* 126k (one sector) for env */
448#define CFG_ENV_SIZE 0x2000
449#else
450#define CFG_ENV_IS_NOWHERE 1 /* Store ENV in memory only */
451#define CFG_ENV_ADDR (CFG_MONITOR_BASE - 0x1000)
452#define CFG_ENV_SIZE 0x2000
453#endif
454
455#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
456#define CFG_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
457
458
459/*
460 * BOOTP options
461 */
462#define CONFIG_BOOTP_BOOTFILESIZE
463#define CONFIG_BOOTP_BOOTPATH
464#define CONFIG_BOOTP_GATEWAY
465#define CONFIG_BOOTP_HOSTNAME
466
467
468/*
469 * Command line configuration.
470 */
471#include <config_cmd_default.h>
472
473#define CONFIG_CMD_PING
474#define CONFIG_CMD_I2C
475#define CONFIG_CMD_MII
476
477#if defined(CFG_RAMBOOT)
478#undef CONFIG_CMD_ENV
479#endif
480
481#if defined(CONFIG_PCI)
482#define CONFIG_CMD_PCI
483#define CONFIG_CMD_SCSI
484#define CONFIG_CMD_EXT2
070ba561 485#define CONFIG_CMD_USB
9553df86
JL
486#endif
487
488
489#undef CONFIG_WATCHDOG /* watchdog disabled */
490
a877880c
YS
491/*DIU Configuration*/
492#define DIU_CONNECT_TO_DVI /* DIU controller connects to DVI encoder*/
493
9553df86
JL
494/*
495 * Miscellaneous configurable options
496 */
497#define CFG_LONGHELP /* undef to save memory */
6bee764b 498#define CONFIG_CMDLINE_EDITING /* Command-line editing */
9553df86
JL
499#define CFG_LOAD_ADDR 0x2000000 /* default load address */
500#define CFG_PROMPT "=> " /* Monitor Command Prompt */
501
502#if defined(CONFIG_CMD_KGDB)
503#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
504#else
505#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
506#endif
507
508#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16) /* Print Buffer Size */
509#define CFG_MAXARGS 16 /* max number of command args */
510#define CFG_BARGSIZE CFG_CBSIZE /* Boot Argument Buffer Size */
511#define CFG_HZ 1000 /* decrementer freq: 1ms ticks */
512
513/*
514 * For booting Linux, the board info and command line data
515 * have to be in the first 8 MB of memory, since this is
516 * the maximum mapped by the Linux kernel during initialization.
517 */
518#define CFG_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux*/
519
9553df86
JL
520/*
521 * Internal Definitions
522 *
523 * Boot Flags
524 */
525#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
526#define BOOTFLAG_WARM 0x02 /* Software reboot */
527
528#if defined(CONFIG_CMD_KGDB)
529#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
530#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
531#endif
532
533/*
534 * Environment Configuration
535 */
536#define CONFIG_IPADDR 192.168.1.100
537
538#define CONFIG_HOSTNAME unknown
539#define CONFIG_ROOTPATH /opt/nfsroot
540#define CONFIG_BOOTFILE uImage
541#define CONFIG_UBOOTPATH 8610hpcd/u-boot.bin
542
543#define CONFIG_SERVERIP 192.168.1.1
544#define CONFIG_GATEWAYIP 192.168.1.1
545#define CONFIG_NETMASK 255.255.255.0
546
547/* default location for tftp and bootm */
548#define CONFIG_LOADADDR 1000000
549
550#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
551#undef CONFIG_BOOTARGS /* the boot command will set bootargs */
552
553#define CONFIG_BAUDRATE 115200
554
555#if defined(CONFIG_PCI1)
556#define PCI_ENV \
557 "pcireg=md ${a}000 3; echo o;md ${a}c00 25; echo i; md ${a}da0 15;" \
558 "echo e;md ${a}e00 9\0" \
559 "pci1regs=setenv a e0008; run pcireg\0" \
560 "pcierr=md ${a}e00 8; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;" \
561 "pci d.w $b.0 56 1\0" \
562 "pcierrc=mw ${a}e00 ffffffff; pci w.b $b.0 7 ff; pci w.w $b.0 1e ffff;" \
563 "pci w.w $b.0 56 ffff\0" \
564 "pci1err=setenv a e0008; run pcierr\0" \
565 "pci1errc=setenv a e0008; run pcierrc\0"
566#else
567#define PCI_ENV ""
568#endif
569
570#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2)
571#define PCIE_ENV \
572 "pciereg=md ${a}000 6; md ${a}020 4; md ${a}bf8 2; echo o;md ${a}c00 25;" \
573 "echo i; md ${a}da0 15; echo e;md ${a}e00 e; echo d; md ${a}f00 c\0" \
574 "pcie1regs=setenv a e000a; run pciereg\0" \
575 "pcie2regs=setenv a e0009; run pciereg\0" \
576 "pcieerr=md ${a}020 1; md ${a}e00; pci d.b $b.0 7 1; pci d.w $b.0 1e 1;"\
577 "pci d.w $b.0 56 1; pci d $b.0 104 1; pci d $b.0 110 1;" \
578 "pci d $b.0 130 1\0" \
579 "pcieerrc=mw ${a}020 ffffffff; mw ${a}e00 ffffffff; pci w.b $b.0 7 ff;"\
580 "pci w.w $b.0 1e ffff; pci w.w $b.0 56 ffff; pci w $b.0 104 ffffffff;" \
581 "pci w $b.0 110 ffffffff; pci w $b.0 130 ffffffff\0" \
582 "pciecfg=pci d $b.0 0 20; pci d $b.0 100 e; pci d $b.0 400 69\0" \
583 "pcie1err=setenv a e000a; run pcieerr\0" \
584 "pcie2err=setenv a e0009; run pcieerr\0" \
585 "pcie1errc=setenv a e000a; run pcieerrc\0" \
586 "pcie2errc=setenv a e0009; run pcieerrc\0"
587#else
588#define PCIE_ENV ""
589#endif
590
591#define DMA_ENV \
592 "dma0=mw ${d}104 ffffffff;mw ${d}110 50000;mw ${d}114 $sad0;mw ${d}118 50000;"\
593 "mw ${d}120 $bc0;mw ${d}100 f03c404; mw ${d}11c $dad0; md ${d}100 9\0" \
594 "dma1=mw ${d}184 ffffffff;mw ${d}190 50000;mw ${d}194 $sad1;mw ${d}198 50000;"\
595 "mw ${d}1a0 $bc1;mw ${d}180 f03c404; mw ${d}19c $dad1; md ${d}180 9\0" \
596 "dma2=mw ${d}204 ffffffff;mw ${d}210 50000;mw ${d}214 $sad2;mw ${d}218 50000;"\
597 "mw ${d}220 $bc2;mw ${d}200 f03c404; mw ${d}21c $dad2; md ${d}200 9\0" \
598 "dma3=mw ${d}284 ffffffff;mw ${d}290 50000;mw ${d}294 $sad3;mw ${d}298 50000;"\
599 "mw ${d}2a0 $bc3;mw ${d}280 f03c404; mw ${d}29c $dad3; md ${d}280 9\0"
600
1815338f 601#ifdef ENV_DEBUG
9553df86
JL
602#define CONFIG_EXTRA_ENV_SETTINGS \
603 "netdev=eth0\0" \
604 "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
605 "tftpflash=tftpboot $loadaddr $uboot; " \
606 "protect off " MK_STR(TEXT_BASE) " +$filesize; " \
607 "erase " MK_STR(TEXT_BASE) " +$filesize; " \
608 "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
609 "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
610 "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
611 "consoledev=ttyS0\0" \
612 "ramdiskaddr=2000000\0" \
613 "ramdiskfile=8610hpcd/ramdisk.uboot\0" \
1df170f8
JL
614 "fdtaddr=c00000\0" \
615 "fdtfile=8610hpcd/mpc8610_hpcd.dtb\0" \
9553df86
JL
616 "bdev=sda3\0" \
617 "en-wd=mw.b f8100010 0x08; echo -expect:- 08; md.b f8100010 1\0" \
618 "dis-wd=mw.b f8100010 0x00; echo -expect:- 00; md.b f8100010 1\0" \
619 "maxcpus=1" \
620 "eoi=mw e00400b0 0\0" \
621 "iack=md e00400a0 1\0" \
622 "ddrreg=md ${a}000 8; md ${a}080 8;md ${a}100 d; md ${a}140 4;" \
623 "md ${a}bf0 4; md ${a}e00 3; md ${a}e20 3; md ${a}e40 7;" \
624 "md ${a}f00 5\0" \
625 "ddr1regs=setenv a e0002; run ddrreg\0" \
626 "gureg=md ${a}000 2c; md ${a}0b0 1; md ${a}0c0 1; md ${a}800 1;" \
627 "md ${a}900 6; md ${a}a00 1; md ${a}b20 3; md ${a}e00 1;" \
628 "md ${a}e60 1; md ${a}ef0 1d\0" \
629 "guregs=setenv a e00e0; run gureg\0" \
630 "mcmreg=md ${a}000 1b; md ${a}bf8 2; md ${a}e00 5\0" \
631 "mcmregs=setenv a e0001; run mcmreg\0" \
632 "diuregs=md e002c000 1d\0" \
633 "dium=mw e002c01c\0" \
634 "diuerr=md e002c014 1\0" \
a877880c
YS
635 "othbootargs=diufb=15M video=fslfb:1280x1024-32@60,monitor=0 debug\0" \
636 "monitor=0-DVI\0" \
9553df86
JL
637 "pmregs=md e00e1000 2b\0" \
638 "lawregs=md e0000c08 4b\0" \
639 "lbcregs=md e0005000 36\0" \
640 "dma0regs=md e0021100 12\0" \
641 "dma1regs=md e0021180 12\0" \
642 "dma2regs=md e0021200 12\0" \
643 "dma3regs=md e0021280 12\0" \
644 PCI_ENV \
645 PCIE_ENV \
646 DMA_ENV
1815338f
YS
647#else
648#define CONFIG_EXTRA_ENV_SETTINGS \
649 "netdev=eth0\0" \
650 "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0" \
651 "consoledev=ttyS0\0" \
652 "ramdiskaddr=2000000\0" \
653 "ramdiskfile=8610hpcd/ramdisk.uboot\0" \
1df170f8
JL
654 "fdtaddr=c00000\0" \
655 "fdtfile=8610hpcd/mpc8610_hpcd.dtb\0" \
a877880c
YS
656 "bdev=sda3\0" \
657 "othbootargs=diufb=15M video=fslfb:1280x1024-32@60,monitor=0\0"\
658 "monitor=0-DVI\0"
1815338f 659#endif
9553df86
JL
660
661#define CONFIG_NFSBOOTCOMMAND \
662 "setenv bootargs root=/dev/nfs rw " \
663 "nfsroot=$serverip:$rootpath " \
664 "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
665 "console=$consoledev,$baudrate $othbootargs;" \
666 "tftp $loadaddr $bootfile;" \
1df170f8
JL
667 "tftp $fdtaddr $fdtfile;" \
668 "bootm $loadaddr - $fdtaddr"
9553df86
JL
669
670#define CONFIG_RAMBOOTCOMMAND \
671 "setenv bootargs root=/dev/ram rw " \
672 "console=$consoledev,$baudrate $othbootargs;" \
673 "tftp $ramdiskaddr $ramdiskfile;" \
674 "tftp $loadaddr $bootfile;" \
1df170f8
JL
675 "tftp $fdtaddr $fdtfile;" \
676 "bootm $loadaddr $ramdiskaddr $fdtaddr"
9553df86
JL
677
678#define CONFIG_BOOTCOMMAND \
679 "setenv bootargs root=/dev/$bdev rw " \
680 "console=$consoledev,$baudrate $othbootargs;" \
681 "tftp $loadaddr $bootfile;" \
1df170f8
JL
682 "tftp $fdtaddr $fdtfile;" \
683 "bootm $loadaddr - $fdtaddr"
9553df86
JL
684
685#endif /* __CONFIG_H */