[people/ms/u-boot.git] / include / configs / RPXClassic.h

/*
 * (C) Copyright 2000, 2001, 2002
 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

/*
 * board/config.h - configuration options, board specific
 */

/* Yoo. Jonghoon, IPone, yooth@ipone.co.kr
 * U-Boot port on RPXlite board
 */

#ifndef __CONFIG_H
#define __CONFIG_H

#define	RPXClassic_50MHz

/*
 * High Level Configuration Options
 * (easy to change)
 */

#define CONFIG_MPC860           1
#define CONFIG_RPXCLASSIC		1

#define	CONFIG_SYS_TEXT_BASE	0xff000000

#define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
#undef	CONFIG_8xx_CONS_SMC2
#undef	CONFIG_8xx_CONS_NONE
#define CONFIG_BAUDRATE		9600	/* console baudrate = 9600bps	*/

/* Define CONFIG_FEC_ENET to use Fast ethernet instead of ethernet on SCC1   */
#define CONFIG_FEC_ENET
#ifdef CONFIG_FEC_ENET
#define CONFIG_SYS_DISCOVER_PHY        1
#define CONFIG_MII              1
#endif /* CONFIG_FEC_ENET */
#define CONFIG_MISC_INIT_R

/* Video console (graphic: Epson SED13806 on ECCX board, no keyboard         */
#if 1
#define CONFIG_VIDEO_SED13806
#define CONFIG_NEC_NL6448BC20
#define CONFIG_VIDEO_SED13806_16BPP

#define CONFIG_CFB_CONSOLE
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO
#define CONFIG_CONSOLE_EXTRA_INFO
#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_VIDEO_SW_CURSOR
#endif

#if 0
#define CONFIG_BOOTDELAY	-1	/* autoboot disabled		*/
#else
#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
#endif

#define CONFIG_ZERO_BOOTDELAY_CHECK 1

#undef	CONFIG_BOOTARGS
#define CONFIG_BOOTCOMMAND							\
	"tftpboot; "								\
	"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} "	\
	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; "	\
	"bootm"

#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
#undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/

#undef	CONFIG_WATCHDOG			/* watchdog disabled		*/

/*
 * BOOTP options
 */
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_BOOTFILESIZE


#define	CONFIG_CLOCKS_IN_MHZ	1	/* clocks passsed to Linux in MHz */


/*
 * Command line configuration.
 */
#include <config_cmd_default.h>

#define CONFIG_CMD_ELF


/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_RESET_ADDRESS	0x80000000
#define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/
#define	CONFIG_SYS_PROMPT	"=> "		/* Monitor Command Prompt	*/
#if defined(CONFIG_CMD_KGDB)
#define	CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
#else
#define	CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
#endif
#define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define	CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/

#define CONFIG_SYS_MEMTEST_START	0x0040000	/* memtest works on	*/
#define CONFIG_SYS_MEMTEST_END		0x00C0000	/* 4 ... 12 MB in DRAM	*/

#define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/

#define	CONFIG_SYS_HZ		1000		/* decrementer freq: 1 ms ticks	*/

/*
 * Low Level Configuration Settings
 * (address mappings, register initial values, etc.)
 * You should know what you are doing if you make changes here.
 */
/*-----------------------------------------------------------------------
 * Internal Memory Mapped Register
 */
#define CONFIG_SYS_IMMR		0xFA200000

/*-----------------------------------------------------------------------------
 * I2C Configuration
 *-----------------------------------------------------------------------------
 */
#define CONFIG_SYS_I2C_SPEED		50000
#define CONFIG_SYS_I2C_SLAVE		0x34


/* enable I2C and select the hardware/software driver */
#define CONFIG_HARD_I2C		1	/* I2C with hardware support	*/
#undef  CONFIG_SYS_I2C_SOFT		/* I2C bit-banged		*/

#if defined(CONFIG_SYS_I2C_SOFT)
#define CONFIG_SYS_I2C			1
/*
 * Software (bit-bang) I2C driver configuration
 */
#define I2C_PORT	1		/* Port A=0, B=1, C=2, D=3 */
#define I2C_ACTIVE	(iop->pdir |=  0x00000010)
#define I2C_TRISTATE	(iop->pdir &= ~0x00000010)
#define I2C_READ	((iop->pdat & 0x00000010) != 0)
#define I2C_SDA(bit)	if(bit) iop->pdat |=  0x00000010; \
			else    iop->pdat &= ~0x00000010
#define I2C_SCL(bit)	if(bit) iop->pdat |=  0x00000020; \
			else    iop->pdat &= ~0x00000020
#define I2C_DELAY	udelay(5)	/* 1/4 I2C clock duration */


#define CONFIG_SYS_I2C_SOFT_SPEED	50000
#define CONFIG_SYS_I2C_SOFT_SLAVE	0x34
#endif

# define CONFIG_SYS_I2C_EEPROM_ADDR	0x50	/* EEPROM X24C16		*/
# define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1	/* bytes of address		*/
/* mask of address bits that overflow into the "EEPROM chip address"    */
#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW	0x07

/*-----------------------------------------------------------------------
 * Definitions for initial stack pointer and data area (in DPRAM)
 */
#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
#define	CONFIG_SYS_INIT_RAM_SIZE	0x3000	/* Size of used area in DPRAM	*/
#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

/*-----------------------------------------------------------------------
 * Start addresses for the final memory configuration
 * (Set up by the startup code)
 * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
 */
#define	CONFIG_SYS_SDRAM_BASE		0x00000000
#define CONFIG_SYS_FLASH_BASE	0xFF000000

#if defined(DEBUG) || defined (CONFIG_VIDEO_SED13806) || defined(CONFIG_CMD_IDE)
#define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
#else
#define	CONFIG_SYS_MONITOR_LEN		(128 << 10)	/* Reserve 128 kB for Monitor	*/
#endif
#define CONFIG_SYS_MONITOR_BASE	0xFF000000
/*%%% #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE */
#define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/

/*
 * For booting Linux, the board info and command line data
 * have to be in the first 8 MB of memory, since this is
 * the maximum mapped by the Linux kernel during initialization.
 */
#define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/

/*-----------------------------------------------------------------------
 * FLASH organization
 */
#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
#define CONFIG_SYS_MAX_FLASH_SECT	71	/* max number of sectors on one chip	*/

#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/

#if 0
#define	CONFIG_ENV_IS_IN_FLASH	1
#define	CONFIG_ENV_OFFSET		0x20000	/*   Offset   of Environment Sector  */
#define CONFIG_ENV_SECT_SIZE       0x8000
#define	CONFIG_ENV_SIZE		0x8000	/* Total Size of Environment Sector  */
#else
#define CONFIG_ENV_IS_IN_NVRAM     1
#define CONFIG_ENV_ADDR            0xfa000100
#define CONFIG_ENV_SIZE            0x1000
#endif

/*-----------------------------------------------------------------------
 * Cache Configuration
 */
#define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
#endif

/*-----------------------------------------------------------------------
 * SYPCR - System Protection Control				11-9
 * SYPCR can only be written once after reset!
 *-----------------------------------------------------------------------
 * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
 */
#define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
			 SYPCR_SWP)

/*-----------------------------------------------------------------------
 * SIUMCR - SIU Module Configuration				11-6
 *-----------------------------------------------------------------------
 * PCMCIA config., multi-function pin tri-state
 */
#define CONFIG_SYS_SIUMCR	(SIUMCR_MLRC10)

/*-----------------------------------------------------------------------
 * TBSCR - Time Base Status and Control				11-26
 *-----------------------------------------------------------------------
 * Clear Reference Interrupt Status, Timebase freezing enabled
 */
#define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF | TBSCR_TBE)

/*-----------------------------------------------------------------------
 * RTCSC - Real-Time Clock Status and Control Register		11-27
 *-----------------------------------------------------------------------
 */
/*%%%#define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE) */
#define CONFIG_SYS_RTCSC	(RTCSC_SEC |  RTCSC_ALR | RTCSC_RTE)

/*-----------------------------------------------------------------------
 * PISCR - Periodic Interrupt Status and Control		11-31
 *-----------------------------------------------------------------------
 * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
 */
#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF | PISCR_PTE)

/*-----------------------------------------------------------------------
 * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
 *-----------------------------------------------------------------------
 * Reset PLL lock status sticky bit, timer expired status bit and timer
 * interrupt status bit
 *
 * If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
 */
/* up to 50 MHz we use a 1:1 clock */
#define CONFIG_SYS_PLPRCR	( (4 << PLPRCR_MF_SHIFT) | PLPRCR_TEXPS | PLPRCR_SPLSS | PLPRCR_TMIST)

/*-----------------------------------------------------------------------
 * SCCR - System Clock and reset Control Register		15-27
 *-----------------------------------------------------------------------
 * Set clock output, timebase and RTC source and divider,
 * power management and some other internal clocks
 */
#define SCCR_MASK	SCCR_EBDF00
/* up to 50 MHz we use a 1:1 clock */
#define CONFIG_SYS_SCCR	(SCCR_COM00 | SCCR_TBS)

/*-----------------------------------------------------------------------
 * PCMCIA stuff
 *-----------------------------------------------------------------------
 *
 */
#define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
#define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
#define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
#define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
#define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
#define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
#define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
#define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )

/*-----------------------------------------------------------------------
 * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
 *-----------------------------------------------------------------------
 */

#define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
#define	CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card	Adapter	*/

#undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
#undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
#undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/

#define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
#define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/

#define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000

#define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR

/* Offset for data I/O			*/
#define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)

/* Offset for normal register accesses	*/
#define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)

/* Offset for alternate registers	*/
#define CONFIG_SYS_ATA_ALT_OFFSET	0x0100

/*-----------------------------------------------------------------------
 *
 *-----------------------------------------------------------------------
 *
 */
/* #define	CONFIG_SYS_DER	0x2002000F */
#define CONFIG_SYS_DER	0

/*
 * Init Memory Controller:
 *
 * BR0 and OR0 (FLASH)
 */

#define FLASH_BASE_PRELIM	0xFE000000	/* FLASH base */
#define CONFIG_SYS_PRELIM_OR_AM	0xFE000000	/* OR addr mask */

/* FLASH timing: ACS = 0, TRLX = 0, CSNT = 0, SCY = 4, ETHR = 0, BIH = 1 */
#define CONFIG_SYS_OR_TIMING_FLASH (OR_SCY_4_CLK | OR_BI)

#define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
#define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE_PRELIM & BR_BA_MSK) | BR_V)

/*
 * BR1 and OR1 (SDRAM)
 *
 */
#define SDRAM_BASE_PRELIM	0x00000000	/* SDRAM base	*/
#define	SDRAM_MAX_SIZE		0x01000000	/* max 16 MB */

/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
#define CONFIG_SYS_OR_TIMING_SDRAM	0x00000E00

#define CONFIG_SYS_OR1_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
#define CONFIG_SYS_BR1_PRELIM	((SDRAM_BASE_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )

/* RPXLITE mem setting */
#define	CONFIG_SYS_BR3_PRELIM	0xFA400001		/* BCSR */
#define CONFIG_SYS_OR3_PRELIM	0xff7f8970
#define	CONFIG_SYS_BR4_PRELIM	0xFA000401		/* NVRAM&SRAM */
#define CONFIG_SYS_OR4_PRELIM	0xFFF80970

/* ECCX CS settings                                                          */
#define SED13806_OR             0xFFC00108     /* - 4 Mo
						   - Burst inhibit
						   - external TA             */
#define SED13806_REG_ADDR       0xa0000000
#define SED13806_ACCES          0x801           /* 16 bit access             */


/* Global definitions for the ECCX board                                     */
#define ECCX_CSR_ADDR           (0xfac00000)
#define ECCX_CSR8_OFFSET        (0x8)
#define ECCX_CSR11_OFFSET       (0xB)
#define ECCX_CSR12_OFFSET       (0xC)

#define ECCX_CSR8  (volatile unsigned char *)(ECCX_CSR_ADDR + ECCX_CSR8_OFFSET)
#define ECCX_CSR11 (volatile unsigned char *)(ECCX_CSR_ADDR + ECCX_CSR11_OFFSET)
#define ECCX_CSR12 (volatile unsigned char *)(ECCX_CSR_ADDR + ECCX_CSR12_OFFSET)


#define REG_GPIO_CTRL 0x008

/* Definitions for CSR8                                                      */
#define ECCX_ENEPSON            0x80    /* Bit 0:
					   0= disable and reset SED1386
					   1= enable SED1386                 */
/* Bit 1:   0= SED1386 in Big Endian mode                                    */
/*          1= SED1386 in little endian mode                                 */
#define ECCX_LE                 0x40
#define ECCX_BE                 0x00

/* Bit 2,3: Selection                                                        */
/*      00 = Disabled                                                        */
/*      01 = CS2 is used for the SED1386                                     */
/*      10 = CS5 is used for the SED1386                                     */
/*      11 = reserved                                                        */
#define ECCX_CS2                0x10
#define ECCX_CS5                0x20

/* Definitions for CSR12                                                     */
#define ECCX_ID                 0x02
#define ECCX_860                0x01

/*
 * Memory Periodic Timer Prescaler
 */

/* periodic timer for refresh */
#define CONFIG_SYS_MAMR_PTA	58

/*
 * Refresh clock Prescalar
 */
#define CONFIG_SYS_MPTPR	MPTPR_PTP_DIV8

/*
 * MAMR settings for SDRAM
 */

/* 10 column SDRAM */
#define CONFIG_SYS_MAMR_10COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
			 MAMR_AMA_TYPE_2 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A12 |	\
			 MAMR_GPL_A4DIS | MAMR_RLFA_4X | MAMR_WLFA_3X | MAMR_TLFA_16X)

/*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */
/* Configuration variable added by yooth. */
/*%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% */

/*
 * BCSRx
 *
 * Board Status and Control Registers
 *
 */

#define BCSR0 0xFA400000
#define BCSR1 0xFA400001
#define BCSR2 0xFA400002
#define BCSR3 0xFA400003

#define BCSR0_ENMONXCVR	0x01	/* Monitor XVCR Control */
#define BCSR0_ENNVRAM	0x02	/* CS4# Control */
#define BCSR0_LED5		0x04	/* LED5 control 0='on' 1='off' */
#define BCSR0_LED4		0x08	/* LED4 control 0='on' 1='off' */
#define BCSR0_FULLDPLX	0x10	/* Ethernet XCVR Control */
#define BCSR0_COLTEST	0x20
#define BCSR0_ETHLPBK	0x40
#define BCSR0_ETHEN	0x80

#define BCSR1_PCVCTL7	0x01	/* PC Slot B Control */
#define BCSR1_PCVCTL6	0x02
#define BCSR1_PCVCTL5	0x04
#define BCSR1_PCVCTL4	0x08
#define BCSR1_IPB5SEL	0x10

#define BCSR2_MIIRST    0x80
#define BCSR2_MIIPWRDWN 0x40
#define BCSR2_MIICTL    0x08

#define BCSR3_BWRTC		0x01	/* Real Time Clock Battery */
#define BCSR3_BWNVR		0x02	/* NVRAM Battery */
#define BCSR3_RDY_BSY	0x04	/* Flash Operation */
#define BCSR3_RPXL		0x08	/* Reserved (reads back '1') */
#define BCSR3_D27		0x10	/* Dip Switch settings */
#define BCSR3_D26		0x20
#define BCSR3_D25		0x40
#define BCSR3_D24		0x80


/*
 * Environment setting
 */

/* #define CONFIG_ETHADDR	00:10:EC:00:2C:A2 */
/* #define CONFIG_IPADDR	10.10.106.1 */
/* #define CONFIG_SERVERIP	10.10.104.11 */

#endif	/* __CONFIG_H */
Commit	Line	Data
5b1d7137 WD	1	/*
	2	* (C) Copyright 2000, 2001, 2002
	3	* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
	4	*
1a459660	5	* SPDX-License-Identifier: GPL-2.0+
5b1d7137 WD	6	*/
	7
	8	/*
	9	* board/config.h - configuration options, board specific
	10	*/
	11
	12	/* Yoo. Jonghoon, IPone, yooth@ipone.co.kr
	13	* U-Boot port on RPXlite board
	14	*/
	15
	16	#ifndef __CONFIG_H
	17	#define __CONFIG_H
	18
	19	#define RPXClassic_50MHz
	20
	21	/*
	22	* High Level Configuration Options
	23	* (easy to change)
	24	*/
	25
	26	#define CONFIG_MPC860 1
	27	#define CONFIG_RPXCLASSIC 1
	28
2ae18241 WD	29	#define CONFIG_SYS_TEXT_BASE 0xff000000
2ae18241 WD	30
5b1d7137 WD	31	#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
	32	#undef CONFIG_8xx_CONS_SMC2
	33	#undef CONFIG_8xx_CONS_NONE
	34	#define CONFIG_BAUDRATE 9600 /* console baudrate = 9600bps */
	35
5b1d7137	36	/* Define CONFIG_FEC_ENET to use Fast ethernet instead of ethernet on SCC1 */
a6c7ad2f	37	#define CONFIG_FEC_ENET
5b1d7137	38	#ifdef CONFIG_FEC_ENET
6d0f6bcf	39	#define CONFIG_SYS_DISCOVER_PHY 1
a6c7ad2f	40	#define CONFIG_MII 1
5b1d7137	41	#endif /* CONFIG_FEC_ENET */
d8d21e69	42	#define CONFIG_MISC_INIT_R
5b1d7137	43
a6c7ad2f WD	44	/* Video console (graphic: Epson SED13806 on ECCX board, no keyboard */
	45	#if 1
	46	#define CONFIG_VIDEO_SED13806
	47	#define CONFIG_NEC_NL6448BC20
	48	#define CONFIG_VIDEO_SED13806_16BPP
	49
	50	#define CONFIG_CFB_CONSOLE
	51	#define CONFIG_VIDEO_LOGO
	52	#define CONFIG_VIDEO_BMP_LOGO
	53	#define CONFIG_CONSOLE_EXTRA_INFO
	54	#define CONFIG_VGA_AS_SINGLE_DEVICE
	55	#define CONFIG_VIDEO_SW_CURSOR
	56	#endif
	57
5b1d7137 WD	58	#if 0
	59	#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
	60	#else
	61	#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
	62	#endif
	63
	64	#define CONFIG_ZERO_BOOTDELAY_CHECK 1
	65
	66	#undef CONFIG_BOOTARGS
	67	#define CONFIG_BOOTCOMMAND \
53677ef1 WD	68	"tftpboot; " \
	69	"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
	70	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
5b1d7137 WD	71	"bootm"
	72
	73	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
6d0f6bcf	74	#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
5b1d7137 WD	75
	76	#undef CONFIG_WATCHDOG /* watchdog disabled */
	77
18225e8d JL	78	/*
	79	* BOOTP options
	80	*/
	81	#define CONFIG_BOOTP_SUBNETMASK
	82	#define CONFIG_BOOTP_GATEWAY
	83	#define CONFIG_BOOTP_HOSTNAME
	84	#define CONFIG_BOOTP_BOOTPATH
	85	#define CONFIG_BOOTP_BOOTFILESIZE
	86
5b1d7137 WD	87
	88	#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
	89
	90
e9a0f8f1 JL	91	/*
	92	* Command line configuration.
	93	*/
	94	#include <config_cmd_default.h>
	95
	96	#define CONFIG_CMD_ELF
5b1d7137	97
5b1d7137 WD	98
	99	/*
	100	* Miscellaneous configurable options
	101	*/
6d0f6bcf JCPV	102	#define CONFIG_SYS_RESET_ADDRESS 0x80000000
	103	#define CONFIG_SYS_LONGHELP /* undef to save memory */
	104	#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
e9a0f8f1	105	#if defined(CONFIG_CMD_KGDB)
6d0f6bcf	106	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
5b1d7137	107	#else
6d0f6bcf	108	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
5b1d7137	109	#endif
6d0f6bcf JCPV	110	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	111	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	112	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
5b1d7137	113
6d0f6bcf JCPV	114	#define CONFIG_SYS_MEMTEST_START 0x0040000 /* memtest works on */
6d0f6bcf JCPV	115	#define CONFIG_SYS_MEMTEST_END 0x00C0000 /* 4 ... 12 MB in DRAM */
5b1d7137	116
6d0f6bcf	117	#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
5b1d7137	118
6d0f6bcf	119	#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
5b1d7137	120
5b1d7137 WD	121	/*
	122	* Low Level Configuration Settings
	123	* (address mappings, register initial values, etc.)
	124	* You should know what you are doing if you make changes here.
	125	*/
	126	/*-----------------------------------------------------------------------
	127	* Internal Memory Mapped Register
	128	*/
6d0f6bcf	129	#define CONFIG_SYS_IMMR 0xFA200000
5b1d7137 WD	130
	131	/*-----------------------------------------------------------------------------
	132	* I2C Configuration
	133	*-----------------------------------------------------------------------------
	134	*/
ea818dbb HS	135	#define CONFIG_SYS_I2C_SPEED 50000
ea818dbb HS	136	#define CONFIG_SYS_I2C_SLAVE 0x34
5b1d7137 WD	137
	138
	139	/* enable I2C and select the hardware/software driver */
	140	#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
ea818dbb HS	141	#undef CONFIG_SYS_I2C_SOFT /* I2C bit-banged */
	142
	143	#if defined(CONFIG_SYS_I2C_SOFT)
	144	#define CONFIG_SYS_I2C 1
5b1d7137 WD	145	/*
	146	* Software (bit-bang) I2C driver configuration
	147	*/
	148	#define I2C_PORT 1 /* Port A=0, B=1, C=2, D=3 */
	149	#define I2C_ACTIVE (iop->pdir \|= 0x00000010)
	150	#define I2C_TRISTATE (iop->pdir &= ~0x00000010)
	151	#define I2C_READ ((iop->pdat & 0x00000010) != 0)
	152	#define I2C_SDA(bit) if(bit) iop->pdat \|= 0x00000010; \
	153	else iop->pdat &= ~0x00000010
	154	#define I2C_SCL(bit) if(bit) iop->pdat \|= 0x00000020; \
	155	else iop->pdat &= ~0x00000020
	156	#define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */
	157
	158
ea818dbb HS	159	#define CONFIG_SYS_I2C_SOFT_SPEED 50000
	160	#define CONFIG_SYS_I2C_SOFT_SLAVE 0x34
	161	#endif
	162
6d0f6bcf JCPV	163	# define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM X24C16 */
6d0f6bcf JCPV	164	# define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* bytes of address */
5b1d7137	165	/* mask of address bits that overflow into the "EEPROM chip address" */
6d0f6bcf	166	#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
5b1d7137 WD	167
	168	/*-----------------------------------------------------------------------
	169	* Definitions for initial stack pointer and data area (in DPRAM)
	170	*/
6d0f6bcf	171	#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
553f0982	172	#define CONFIG_SYS_INIT_RAM_SIZE 0x3000 /* Size of used area in DPRAM */
25ddd1fb	173	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
6d0f6bcf	174	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
5b1d7137 WD	175
	176	/*-----------------------------------------------------------------------
	177	* Start addresses for the final memory configuration
	178	* (Set up by the startup code)
6d0f6bcf	179	* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
5b1d7137	180	*/
6d0f6bcf JCPV	181	#define CONFIG_SYS_SDRAM_BASE 0x00000000
6d0f6bcf JCPV	182	#define CONFIG_SYS_FLASH_BASE 0xFF000000
5b1d7137	183
e9a0f8f1	184	#if defined(DEBUG) \|\| defined (CONFIG_VIDEO_SED13806) \|\| defined(CONFIG_CMD_IDE)
6d0f6bcf	185	#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
5b1d7137	186	#else
6d0f6bcf	187	#define CONFIG_SYS_MONITOR_LEN (128 << 10) /* Reserve 128 kB for Monitor */
5b1d7137	188	#endif
6d0f6bcf JCPV	189	#define CONFIG_SYS_MONITOR_BASE 0xFF000000
	190	/%%% #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE /
	191	#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
5b1d7137 WD	192
	193	/*
	194	* For booting Linux, the board info and command line data
	195	* have to be in the first 8 MB of memory, since this is
	196	* the maximum mapped by the Linux kernel during initialization.
	197	*/
6d0f6bcf	198	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
5b1d7137 WD	199
	200	/*-----------------------------------------------------------------------
	201	* FLASH organization
	202	*/
6d0f6bcf JCPV	203	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
6d0f6bcf JCPV	204	#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip */
5b1d7137	205
6d0f6bcf JCPV	206	#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
6d0f6bcf JCPV	207	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
5b1d7137 WD	208
5b1d7137 WD	209	#if 0
5a1aceb0	210	#define CONFIG_ENV_IS_IN_FLASH 1
0e8d1586 JCPV	211	#define CONFIG_ENV_OFFSET 0x20000 /* Offset of Environment Sector */
	212	#define CONFIG_ENV_SECT_SIZE 0x8000
	213	#define CONFIG_ENV_SIZE 0x8000 /* Total Size of Environment Sector */
5b1d7137	214	#else
9314cee6	215	#define CONFIG_ENV_IS_IN_NVRAM 1
0e8d1586 JCPV	216	#define CONFIG_ENV_ADDR 0xfa000100
0e8d1586 JCPV	217	#define CONFIG_ENV_SIZE 0x1000
5b1d7137 WD	218	#endif
	219
	220	/*-----------------------------------------------------------------------
	221	* Cache Configuration
	222	*/
6d0f6bcf	223	#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
e9a0f8f1	224	#if defined(CONFIG_CMD_KGDB)
6d0f6bcf	225	#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
5b1d7137 WD	226	#endif
	227
	228	/*-----------------------------------------------------------------------
	229	* SYPCR - System Protection Control 11-9
	230	* SYPCR can only be written once after reset!
	231	*-----------------------------------------------------------------------
	232	* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
	233	*/
6d0f6bcf	234	#define CONFIG_SYS_SYPCR (SYPCR_SWTC \| SYPCR_BMT \| SYPCR_BME \| SYPCR_SWF \| \
5b1d7137 WD	235	SYPCR_SWP)
	236
	237	/*-----------------------------------------------------------------------
	238	* SIUMCR - SIU Module Configuration 11-6
	239	*-----------------------------------------------------------------------
	240	* PCMCIA config., multi-function pin tri-state
	241	*/
6d0f6bcf	242	#define CONFIG_SYS_SIUMCR (SIUMCR_MLRC10)
5b1d7137 WD	243
	244	/*-----------------------------------------------------------------------
	245	* TBSCR - Time Base Status and Control 11-26
	246	*-----------------------------------------------------------------------
	247	* Clear Reference Interrupt Status, Timebase freezing enabled
	248	*/
6d0f6bcf	249	#define CONFIG_SYS_TBSCR (TBSCR_REFA \| TBSCR_REFB \| TBSCR_TBF \| TBSCR_TBE)
5b1d7137 WD	250
	251	/*-----------------------------------------------------------------------
	252	* RTCSC - Real-Time Clock Status and Control Register 11-27
	253	*-----------------------------------------------------------------------
	254	*/
6d0f6bcf JCPV	255	/%%%#define CONFIG_SYS_RTCSC (RTCSC_SEC \| RTCSC_ALR \| RTCSC_RTF\| RTCSC_RTE) /
6d0f6bcf JCPV	256	#define CONFIG_SYS_RTCSC (RTCSC_SEC \| RTCSC_ALR \| RTCSC_RTE)
5b1d7137 WD	257
	258	/*-----------------------------------------------------------------------
	259	* PISCR - Periodic Interrupt Status and Control 11-31
	260	*-----------------------------------------------------------------------
	261	* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
	262	*/
6d0f6bcf	263	#define CONFIG_SYS_PISCR (PISCR_PS \| PISCR_PITF \| PISCR_PTE)
5b1d7137 WD	264
	265	/*-----------------------------------------------------------------------
	266	* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
	267	*-----------------------------------------------------------------------
	268	* Reset PLL lock status sticky bit, timer expired status bit and timer
	269	* interrupt status bit
	270	*
	271	* If this is a 80 MHz CPU, set PLL multiplication factor to 5 (5*16=80)!
	272	*/
	273	/* up to 50 MHz we use a 1:1 clock */
6d0f6bcf	274	#define CONFIG_SYS_PLPRCR ( (4 << PLPRCR_MF_SHIFT) \| PLPRCR_TEXPS \| PLPRCR_SPLSS \| PLPRCR_TMIST)
5b1d7137 WD	275
	276	/*-----------------------------------------------------------------------
	277	* SCCR - System Clock and reset Control Register 15-27
	278	*-----------------------------------------------------------------------
	279	* Set clock output, timebase and RTC source and divider,
	280	* power management and some other internal clocks
	281	*/
	282	#define SCCR_MASK SCCR_EBDF00
	283	/* up to 50 MHz we use a 1:1 clock */
6d0f6bcf	284	#define CONFIG_SYS_SCCR (SCCR_COM00 \| SCCR_TBS)
5b1d7137 WD	285
	286	/*-----------------------------------------------------------------------
	287	* PCMCIA stuff
	288	*-----------------------------------------------------------------------
	289	*
	290	*/
6d0f6bcf JCPV	291	#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
	292	#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
	293	#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
	294	#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
	295	#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
	296	#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
	297	#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
	298	#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
5b1d7137 WD	299
	300	/*-----------------------------------------------------------------------
	301	* IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
	302	*-----------------------------------------------------------------------
	303	*/
	304
8d1165e1	305	#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
5b1d7137 WD	306	#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
	307
	308	#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
	309	#undef CONFIG_IDE_LED /* LED for ide not supported */
	310	#undef CONFIG_IDE_RESET /* reset for ide not supported */
	311
6d0f6bcf JCPV	312	#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
6d0f6bcf JCPV	313	#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
5b1d7137	314
6d0f6bcf	315	#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
5b1d7137	316
6d0f6bcf	317	#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
5b1d7137 WD	318
5b1d7137 WD	319	/* Offset for data I/O */
6d0f6bcf	320	#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
5b1d7137 WD	321
5b1d7137 WD	322	/* Offset for normal register accesses */
6d0f6bcf	323	#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
5b1d7137 WD	324
5b1d7137 WD	325	/* Offset for alternate registers */
6d0f6bcf	326	#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
5b1d7137 WD	327
	328	/*-----------------------------------------------------------------------
	329	*
	330	*-----------------------------------------------------------------------
	331	*
	332	*/
6d0f6bcf JCPV	333	/* #define CONFIG_SYS_DER 0x2002000F */
6d0f6bcf JCPV	334	#define CONFIG_SYS_DER 0
5b1d7137 WD	335
	336	/*
	337	* Init Memory Controller:
	338	*
	339	* BR0 and OR0 (FLASH)
	340	*/
	341
	342	#define FLASH_BASE_PRELIM 0xFE000000 /* FLASH base */
6d0f6bcf	343	#define CONFIG_SYS_PRELIM_OR_AM 0xFE000000 /* OR addr mask */
5b1d7137 WD	344
5b1d7137 WD	345	/* FLASH timing: ACS = 0, TRLX = 0, CSNT = 0, SCY = 4, ETHR = 0, BIH = 1 */
6d0f6bcf	346	#define CONFIG_SYS_OR_TIMING_FLASH (OR_SCY_4_CLK \| OR_BI)
5b1d7137	347
6d0f6bcf JCPV	348	#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM \| CONFIG_SYS_OR_TIMING_FLASH)
6d0f6bcf JCPV	349	#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE_PRELIM & BR_BA_MSK) \| BR_V)
5b1d7137 WD	350
	351	/*
	352	* BR1 and OR1 (SDRAM)
	353	*
	354	*/
	355	#define SDRAM_BASE_PRELIM 0x00000000 /* SDRAM base */
	356	#define SDRAM_MAX_SIZE 0x01000000 /* max 16 MB */
	357
	358	/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
6d0f6bcf	359	#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000E00
5b1d7137	360
6d0f6bcf JCPV	361	#define CONFIG_SYS_OR1_PRELIM (CONFIG_SYS_PRELIM_OR_AM \| CONFIG_SYS_OR_TIMING_SDRAM )
6d0f6bcf JCPV	362	#define CONFIG_SYS_BR1_PRELIM ((SDRAM_BASE_PRELIM & BR_BA_MSK) \| BR_MS_UPMA \| BR_V )
5b1d7137 WD	363
5b1d7137 WD	364	/* RPXLITE mem setting */
6d0f6bcf JCPV	365	#define CONFIG_SYS_BR3_PRELIM 0xFA400001 /* BCSR */
	366	#define CONFIG_SYS_OR3_PRELIM 0xff7f8970
	367	#define CONFIG_SYS_BR4_PRELIM 0xFA000401 /* NVRAM&SRAM */
	368	#define CONFIG_SYS_OR4_PRELIM 0xFFF80970
5b1d7137	369
a6c7ad2f WD	370	/* ECCX CS settings */
a6c7ad2f WD	371	#define SED13806_OR 0xFFC00108 /* - 4 Mo
8bde7f77 WD	372	- Burst inhibit
8bde7f77 WD	373	- external TA */
a6c7ad2f WD	374	#define SED13806_REG_ADDR 0xa0000000
	375	#define SED13806_ACCES 0x801 /* 16 bit access */
	376
	377
	378	/* Global definitions for the ECCX board */
	379	#define ECCX_CSR_ADDR (0xfac00000)
	380	#define ECCX_CSR8_OFFSET (0x8)
	381	#define ECCX_CSR11_OFFSET (0xB)
	382	#define ECCX_CSR12_OFFSET (0xC)
	383
	384	#define ECCX_CSR8 (volatile unsigned char *)(ECCX_CSR_ADDR + ECCX_CSR8_OFFSET)
	385	#define ECCX_CSR11 (volatile unsigned char *)(ECCX_CSR_ADDR + ECCX_CSR11_OFFSET)
	386	#define ECCX_CSR12 (volatile unsigned char *)(ECCX_CSR_ADDR + ECCX_CSR12_OFFSET)
	387
	388
	389	#define REG_GPIO_CTRL 0x008
	390
	391	/* Definitions for CSR8 */
	392	#define ECCX_ENEPSON 0x80 /* Bit 0:
8bde7f77 WD	393	0= disable and reset SED1386
8bde7f77 WD	394	1= enable SED1386 */
a6c7ad2f WD	395	/* Bit 1: 0= SED1386 in Big Endian mode */
	396	/* 1= SED1386 in little endian mode */
	397	#define ECCX_LE 0x40
	398	#define ECCX_BE 0x00
	399
	400	/* Bit 2,3: Selection */
	401	/* 00 = Disabled */
	402	/* 01 = CS2 is used for the SED1386 */
	403	/* 10 = CS5 is used for the SED1386 */
	404	/* 11 = reserved */
	405	#define ECCX_CS2 0x10
	406	#define ECCX_CS5 0x20
	407
	408	/* Definitions for CSR12 */
	409	#define ECCX_ID 0x02
	410	#define ECCX_860 0x01
	411
5b1d7137 WD	412	/*
	413	* Memory Periodic Timer Prescaler
	414	*/
	415
	416	/* periodic timer for refresh */
6d0f6bcf	417	#define CONFIG_SYS_MAMR_PTA 58
5b1d7137 WD	418
	419	/*
	420	* Refresh clock Prescalar
	421	*/
6d0f6bcf	422	#define CONFIG_SYS_MPTPR MPTPR_PTP_DIV8
5b1d7137 WD	423
	424	/*
	425	* MAMR settings for SDRAM
	426	*/
	427
	428	/* 10 column SDRAM */
6d0f6bcf	429	#define CONFIG_SYS_MAMR_10COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) \| MAMR_PTAE \| \
5b1d7137 WD	430	MAMR_AMA_TYPE_2 \| MAMR_DSA_1_CYCL \| MAMR_G0CLA_A12 \| \
	431	MAMR_GPL_A4DIS \| MAMR_RLFA_4X \| MAMR_WLFA_3X \| MAMR_TLFA_16X)
	432
5b1d7137 WD	433	/%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% /
	434	/* Configuration variable added by yooth. */
	435	/%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% /
	436
	437	/*
	438	* BCSRx
	439	*
	440	* Board Status and Control Registers
	441	*
	442	*/
	443
	444	#define BCSR0 0xFA400000
	445	#define BCSR1 0xFA400001
	446	#define BCSR2 0xFA400002
	447	#define BCSR3 0xFA400003
	448
	449	#define BCSR0_ENMONXCVR 0x01 /* Monitor XVCR Control */
53677ef1	450	#define BCSR0_ENNVRAM 0x02 /* CS4# Control */
5b1d7137 WD	451	#define BCSR0_LED5 0x04 /* LED5 control 0='on' 1='off' */
	452	#define BCSR0_LED4 0x08 /* LED4 control 0='on' 1='off' */
	453	#define BCSR0_FULLDPLX 0x10 /* Ethernet XCVR Control */
	454	#define BCSR0_COLTEST 0x20
	455	#define BCSR0_ETHLPBK 0x40
	456	#define BCSR0_ETHEN 0x80
	457
	458	#define BCSR1_PCVCTL7 0x01 /* PC Slot B Control */
	459	#define BCSR1_PCVCTL6 0x02
	460	#define BCSR1_PCVCTL5 0x04
	461	#define BCSR1_PCVCTL4 0x08
	462	#define BCSR1_IPB5SEL 0x10
	463
	464	#define BCSR2_MIIRST 0x80
	465	#define BCSR2_MIIPWRDWN 0x40
	466	#define BCSR2_MIICTL 0x08
	467
	468	#define BCSR3_BWRTC 0x01 /* Real Time Clock Battery */
	469	#define BCSR3_BWNVR 0x02 /* NVRAM Battery */
	470	#define BCSR3_RDY_BSY 0x04 /* Flash Operation */
	471	#define BCSR3_RPXL 0x08 /* Reserved (reads back '1') */
	472	#define BCSR3_D27 0x10 /* Dip Switch settings */
	473	#define BCSR3_D26 0x20
	474	#define BCSR3_D25 0x40
	475	#define BCSR3_D24 0x80
	476
	477
	478	/*
	479	* Environment setting
	480	*/
	481
	482	/* #define CONFIG_ETHADDR 00:10:EC:00:2C:A2 */
	483	/* #define CONFIG_IPADDR 10.10.106.1 */
	484	/* #define CONFIG_SERVERIP 10.10.104.11 */
	485
	486	#endif /* __CONFIG_H */