projects / people / ms / u-boot.git / blame
| Commit | Line | Data |
|---|---|---|
| 8b0044ff OZ |
1 | /* |
| 2 | * Copyright 2013-2015 Arcturus Networks, Inc. | |
| 3 | * http://www.arcturusnetworks.com/products/ucp1020/ | |
| 4 | * based on include/configs/p1_p2_rdb_pc.h | |
| 5 | * original copyright follows: | |
| 6 | * Copyright 2009-2011 Freescale Semiconductor, Inc. | |
| 7 | * | |
| 8 | * SPDX-License-Identifier: GPL-2.0+ | |
| 9 | */ | |
| 10 | ||
| 11 | /* | |
| 12 | * QorIQ uCP1020-xx boards configuration file | |
| 13 | */ | |
| 14 | #ifndef __CONFIG_H | |
| 15 | #define __CONFIG_H | |
| 16 | ||
| 8b0044ff | 17 | #define CONFIG_FSL_ELBC |
| 8b0044ff OZ |
18 | #define CONFIG_PCIE1 /* PCIE controller 1 (slot 1) */ |
| 19 | #define CONFIG_PCIE2 /* PCIE controller 2 (slot 2) */ | |
| 20 | #define CONFIG_FSL_PCI_INIT /* Use common FSL init code */ | |
| 21 | #define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */ | |
| 22 | #define CONFIG_FSL_PCIE_RESET /* need PCIe reset errata */ | |
| 23 | #define CONFIG_SYS_PCI_64BIT /* enable 64-bit PCI resources */ | |
| 24 | ||
| 25 | #if defined(CONFIG_TARTGET_UCP1020T1) | |
| 26 | ||
| 27 | #define CONFIG_UCP1020_REV_1_3 | |
| 28 | ||
| 29 | #define CONFIG_BOARDNAME "uCP1020-64EE512-0U1-XR-T1" | |
| 8b0044ff OZ |
30 | |
| 31 | #define CONFIG_TSEC_ENET | |
| 32 | #define CONFIG_TSEC1 | |
| 33 | #define CONFIG_TSEC3 | |
| 34 | #define CONFIG_HAS_ETH0 | |
| 35 | #define CONFIG_HAS_ETH1 | |
| 36 | #define CONFIG_ETHADDR 00:19:D3:FF:FF:FF | |
| 37 | #define CONFIG_ETH1ADDR 00:19:D3:FF:FF:FE | |
| 38 | #define CONFIG_ETH2ADDR 00:19:D3:FF:FF:FD | |
| 39 | #define CONFIG_IPADDR 10.80.41.229 | |
| 40 | #define CONFIG_SERVERIP 10.80.41.227 | |
| 41 | #define CONFIG_NETMASK 255.255.252.0 | |
| 42 | #define CONFIG_ETHPRIME "eTSEC3" | |
| 43 | ||
| 44 | #ifndef CONFIG_SPI_FLASH | |
| 8b0044ff OZ |
45 | #endif |
| 46 | #define CONFIG_SYS_REDUNDAND_ENVIRONMENT | |
| 47 | ||
| 8b0044ff OZ |
48 | #define CONFIG_SYS_L2_SIZE (256 << 10) |
| 49 | ||
| 50 | #define CONFIG_LAST_STAGE_INIT | |
| 51 | ||
| 8b0044ff OZ |
52 | #endif |
| 53 | ||
| 54 | #if defined(CONFIG_TARGET_UCP1020) | |
| 55 | ||
| 56 | #define CONFIG_UCP1020 | |
| 57 | #define CONFIG_UCP1020_REV_1_3 | |
| 58 | ||
| 59 | #define CONFIG_BOARDNAME_LOCAL "uCP1020-64EEE512-OU1-XR" | |
| 8b0044ff OZ |
60 | |
| 61 | #define CONFIG_TSEC_ENET | |
| 62 | #define CONFIG_TSEC1 | |
| 63 | #define CONFIG_TSEC2 | |
| 64 | #define CONFIG_TSEC3 | |
| 65 | #define CONFIG_HAS_ETH0 | |
| 66 | #define CONFIG_HAS_ETH1 | |
| 67 | #define CONFIG_HAS_ETH2 | |
| 68 | #define CONFIG_ETHADDR 00:06:3B:FF:FF:FF | |
| 69 | #define CONFIG_ETH1ADDR 00:06:3B:FF:FF:FE | |
| 70 | #define CONFIG_ETH2ADDR 00:06:3B:FF:FF:FD | |
| 71 | #define CONFIG_IPADDR 192.168.1.81 | |
| 72 | #define CONFIG_IPADDR1 192.168.1.82 | |
| 73 | #define CONFIG_IPADDR2 192.168.1.83 | |
| 74 | #define CONFIG_SERVERIP 192.168.1.80 | |
| 75 | #define CONFIG_GATEWAYIP 102.168.1.1 | |
| 76 | #define CONFIG_NETMASK 255.255.255.0 | |
| 77 | #define CONFIG_ETHPRIME "eTSEC1" | |
| 78 | ||
| 79 | #ifndef CONFIG_SPI_FLASH | |
| 8b0044ff OZ |
80 | #endif |
| 81 | #define CONFIG_SYS_REDUNDAND_ENVIRONMENT | |
| 82 | ||
| 8b0044ff OZ |
83 | #define CONFIG_SYS_L2_SIZE (256 << 10) |
| 84 | ||
| 85 | #define CONFIG_LAST_STAGE_INIT | |
| 86 | ||
| 87 | #endif | |
| 88 | ||
| 89 | #ifdef CONFIG_SDCARD | |
| 90 | #define CONFIG_RAMBOOT_SDCARD | |
| 91 | #define CONFIG_SYS_RAMBOOT | |
| 92 | #define CONFIG_SYS_EXTRA_ENV_RELOC | |
| 93 | #define CONFIG_SYS_TEXT_BASE 0x11000000 | |
| 94 | #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc | |
| 95 | #endif | |
| 96 | ||
| 97 | #ifdef CONFIG_SPIFLASH | |
| 98 | #define CONFIG_RAMBOOT_SPIFLASH | |
| 99 | #define CONFIG_SYS_RAMBOOT | |
| 100 | #define CONFIG_SYS_EXTRA_ENV_RELOC | |
| 101 | #define CONFIG_SYS_TEXT_BASE 0x11000000 | |
| 102 | #define CONFIG_RESET_VECTOR_ADDRESS 0x1107fffc | |
| 103 | #endif | |
| 104 | ||
| 105 | #ifndef CONFIG_SYS_TEXT_BASE | |
| 106 | #define CONFIG_SYS_TEXT_BASE 0xeff80000 | |
| 107 | #endif | |
| 108 | #define CONFIG_SYS_TEXT_BASE_NOR 0xeff80000 | |
| 109 | ||
| 110 | #ifndef CONFIG_RESET_VECTOR_ADDRESS | |
| 111 | #define CONFIG_RESET_VECTOR_ADDRESS 0xeffffffc | |
| 112 | #endif | |
| 113 | ||
| 114 | #ifndef CONFIG_SYS_MONITOR_BASE | |
| 115 | #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */ | |
| 116 | #endif | |
| 117 | ||
| 8b0044ff OZ |
118 | #define CONFIG_MP |
| 119 | ||
| 8b0044ff OZ |
120 | #define CONFIG_ENV_OVERWRITE |
| 121 | ||
| 122 | #define CONFIG_CMD_SATA | |
| 123 | #define CONFIG_SATA_SIL | |
| 124 | #define CONFIG_SYS_SATA_MAX_DEVICE 2 | |
| 125 | #define CONFIG_LIBATA | |
| 126 | #define CONFIG_LBA48 | |
| 127 | ||
| 128 | #define CONFIG_SYS_CLK_FREQ 66666666 | |
| 129 | #define CONFIG_DDR_CLK_FREQ 66666666 | |
| 130 | ||
| 131 | #define CONFIG_HWCONFIG | |
| 132 | ||
| 133 | #define CONFIG_DTT_ADM1021 1 /* ADM1021 temp sensor support */ | |
| 134 | #define CONFIG_SYS_DTT_BUS_NUM 1 /* The I2C bus for DTT */ | |
| 135 | #define CONFIG_DTT_SENSORS { 0, 1 } /* Sensor index */ | |
| 136 | /* | |
| 137 | * ADM1021/NCT72 temp sensor configuration (see dtt/adm1021.c for details). | |
| 138 | * there will be one entry in this array for each two (dummy) sensors in | |
| 139 | * CONFIG_DTT_SENSORS. | |
| 140 | * | |
| 141 | * For uCP1020 module: | |
| 142 | * - only one ADM1021/NCT72 | |
| 143 | * - i2c addr 0x41 | |
| 144 | * - conversion rate 0x02 = 0.25 conversions/second | |
| 145 | * - ALERT output disabled | |
| 146 | * - local temp sensor enabled, min set to 0 deg, max set to 85 deg | |
| 147 | * - remote temp sensor enabled, min set to 0 deg, max set to 85 deg | |
| 148 | */ | |
| 149 | #define CONFIG_SYS_DTT_ADM1021 { { CONFIG_SYS_I2C_NCT72_ADDR, \ | |
| 150 | 0x02, 0, 1, 0, 85, 1, 0, 85} } | |
| 151 | ||
| 152 | #define CONFIG_CMD_DTT | |
| 153 | ||
| 154 | /* | |
| 155 | * These can be toggled for performance analysis, otherwise use default. | |
| 156 | */ | |
| 157 | #define CONFIG_L2_CACHE | |
| 158 | #define CONFIG_BTB | |
| 159 | ||
| 8b0044ff OZ |
160 | #define CONFIG_ENABLE_36BIT_PHYS |
| 161 | ||
| 162 | #define CONFIG_SYS_MEMTEST_START 0x00200000 /* memtest works on */ | |
| 163 | #define CONFIG_SYS_MEMTEST_END 0x1fffffff | |
| 164 | #define CONFIG_PANIC_HANG /* do not reset board on panic */ | |
| 165 | ||
| 166 | #define CONFIG_SYS_CCSRBAR 0xffe00000 | |
| 167 | #define CONFIG_SYS_CCSRBAR_PHYS_LOW CONFIG_SYS_CCSRBAR | |
| 168 | ||
| 169 | /* IN case of NAND bootloader relocate CCSRBAR in RAMboot code not in the 4k | |
| 170 | SPL code*/ | |
| 171 | #ifdef CONFIG_SPL_BUILD | |
| 172 | #define CONFIG_SYS_CCSR_DO_NOT_RELOCATE | |
| 173 | #endif | |
| 174 | ||
| 175 | /* DDR Setup */ | |
| 176 | #define CONFIG_DDR_ECC_ENABLE | |
| 8b0044ff OZ |
177 | #ifndef CONFIG_DDR_ECC_ENABLE |
| 178 | #define CONFIG_SYS_DDR_RAW_TIMING | |
| 179 | #define CONFIG_DDR_SPD | |
| 180 | #endif | |
| 181 | #define CONFIG_SYS_SPD_BUS_NUM 1 | |
| 182 | #undef CONFIG_FSL_DDR_INTERACTIVE | |
| 183 | ||
| 184 | #define CONFIG_SYS_SDRAM_SIZE_LAW LAW_SIZE_512M | |
| 185 | #define CONFIG_CHIP_SELECTS_PER_CTRL 1 | |
| 186 | #define CONFIG_SYS_SDRAM_SIZE (1u << (CONFIG_SYS_SDRAM_SIZE_LAW - 19)) | |
| 187 | #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 | |
| 188 | #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE | |
| 189 | ||
| 8b0044ff OZ |
190 | #define CONFIG_DIMM_SLOTS_PER_CTLR 1 |
| 191 | ||
| 192 | /* Default settings for DDR3 */ | |
| 193 | #define CONFIG_SYS_DDR_CS0_BNDS 0x0000003f | |
| 194 | #define CONFIG_SYS_DDR_CS0_CONFIG 0x80014302 | |
| 195 | #define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000 | |
| 196 | #define CONFIG_SYS_DDR_CS1_BNDS 0x0040007f | |
| 197 | #define CONFIG_SYS_DDR_CS1_CONFIG 0x80014302 | |
| 198 | #define CONFIG_SYS_DDR_CS1_CONFIG_2 0x00000000 | |
| 199 | ||
| 200 | #define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef | |
| 201 | #define CONFIG_SYS_DDR_INIT_ADDR 0x00000000 | |
| 202 | #define CONFIG_SYS_DDR_INIT_EXT_ADDR 0x00000000 | |
| 203 | #define CONFIG_SYS_DDR_MODE_CONTROL 0x00000000 | |
| 204 | ||
| 205 | #define CONFIG_SYS_DDR_ZQ_CONTROL 0x89080600 | |
| 206 | #define CONFIG_SYS_DDR_WRLVL_CONTROL 0x8655A608 | |
| 207 | #define CONFIG_SYS_DDR_SR_CNTR 0x00000000 | |
| 208 | #define CONFIG_SYS_DDR_RCW_1 0x00000000 | |
| 209 | #define CONFIG_SYS_DDR_RCW_2 0x00000000 | |
| 210 | #ifdef CONFIG_DDR_ECC_ENABLE | |
| 211 | #define CONFIG_SYS_DDR_CONTROL 0xE70C0000 /* Type = DDR3 & ECC */ | |
| 212 | #else | |
| 213 | #define CONFIG_SYS_DDR_CONTROL 0xC70C0000 /* Type = DDR3 */ | |
| 214 | #endif | |
| 215 | #define CONFIG_SYS_DDR_CONTROL_2 0x04401050 | |
| 216 | #define CONFIG_SYS_DDR_TIMING_4 0x00220001 | |
| 217 | #define CONFIG_SYS_DDR_TIMING_5 0x03402400 | |
| 218 | ||
| 219 | #define CONFIG_SYS_DDR_TIMING_3 0x00020000 | |
| 220 | #define CONFIG_SYS_DDR_TIMING_0 0x00330004 | |
| 221 | #define CONFIG_SYS_DDR_TIMING_1 0x6f6B4846 | |
| 222 | #define CONFIG_SYS_DDR_TIMING_2 0x0FA8C8CF | |
| 223 | #define CONFIG_SYS_DDR_CLK_CTRL 0x03000000 | |
| 224 | #define CONFIG_SYS_DDR_MODE_1 0x40461520 | |
| 225 | #define CONFIG_SYS_DDR_MODE_2 0x8000c000 | |
| 226 | #define CONFIG_SYS_DDR_INTERVAL 0x0C300000 | |
| 227 | ||
| 228 | #undef CONFIG_CLOCKS_IN_MHZ | |
| 229 | ||
| 230 | /* | |
| 231 | * Memory map | |
| 232 | * | |
| 233 | * 0x0000_0000 0x7fff_ffff DDR Up to 2GB cacheable | |
| 234 | * 0x8000_0000 0xdfff_ffff PCI Express Mem 1G non-cacheable(PCIe * 2) | |
| 235 | * 0xec00_0000 0xefff_ffff NOR flash Up to 64M non-cacheable CS0/1 | |
| 236 | * 0xf8f8_0000 0xf8ff_ffff L2 SRAM Up to 256K cacheable | |
| 237 | * (early boot only) | |
| 238 | * 0xffc0_0000 0xffc3_ffff PCI IO range 256k non-cacheable | |
| 239 | * 0xffd0_0000 0xffd0_3fff L1 for stack 16K cacheable | |
| 240 | * 0xffe0_0000 0xffef_ffff CCSR 1M non-cacheable | |
| 241 | */ | |
| 242 | ||
| 243 | /* | |
| 244 | * Local Bus Definitions | |
| 245 | */ | |
| 246 | #define CONFIG_SYS_MAX_FLASH_SECT 512 /* 64M */ | |
| 247 | #define CONFIG_SYS_FLASH_BASE 0xec000000 | |
| 248 | ||
| 249 | #define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE | |
| 250 | ||
| 251 | #define CONFIG_FLASH_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) \ | |
| 252 | | BR_PS_16 | BR_V) | |
| 253 | ||
| 254 | #define CONFIG_FLASH_OR_PRELIM 0xfc000ff7 | |
| 255 | ||
| 256 | #define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE_PHYS} | |
| 257 | #define CONFIG_SYS_FLASH_QUIET_TEST | |
| 258 | #define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1 */ | |
| 259 | ||
| 260 | #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */ | |
| 261 | ||
| 262 | #undef CONFIG_SYS_FLASH_CHECKSUM | |
| 263 | #define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */ | |
| 264 | #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */ | |
| 265 | ||
| 266 | #define CONFIG_FLASH_CFI_DRIVER | |
| 267 | #define CONFIG_SYS_FLASH_CFI | |
| 268 | #define CONFIG_SYS_FLASH_EMPTY_INFO | |
| 269 | #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE | |
| 270 | ||
| 271 | #define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r function */ | |
| 272 | ||
| 273 | #define CONFIG_SYS_INIT_RAM_LOCK | |
| 274 | #define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /* stack in RAM */ | |
| 275 | /* Initial L1 address */ | |
| 276 | #define CONFIG_SYS_INIT_RAM_ADDR_PHYS CONFIG_SYS_INIT_RAM_ADDR | |
| 277 | #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_HIGH 0 | |
| 278 | #define CONFIG_SYS_INIT_RAM_ADDR_PHYS_LOW CONFIG_SYS_INIT_RAM_ADDR_PHYS | |
| 279 | /* Size of used area in RAM */ | |
| 280 | #define CONFIG_SYS_INIT_RAM_SIZE 0x00004000 | |
| 281 | ||
| 282 | #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \ | |
| 283 | GENERATED_GBL_DATA_SIZE) | |
| 284 | #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET | |
| 285 | ||
| 286 | #define CONFIG_SYS_MONITOR_LEN (256 * 1024)/* Reserve 256 kB for Mon */ | |
| 287 | #define CONFIG_SYS_MALLOC_LEN (1024 * 1024)/* Reserved for malloc */ | |
| 288 | ||
| 289 | #define CONFIG_SYS_PMC_BASE 0xff980000 | |
| 290 | #define CONFIG_SYS_PMC_BASE_PHYS CONFIG_SYS_PMC_BASE | |
| 291 | #define CONFIG_PMC_BR_PRELIM (BR_PHYS_ADDR(CONFIG_SYS_PMC_BASE_PHYS) | \ | |
| 292 | BR_PS_8 | BR_V) | |
| 293 | #define CONFIG_PMC_OR_PRELIM (OR_AM_64KB | OR_GPCM_CSNT | OR_GPCM_XACS | \ | |
| 294 | OR_GPCM_SCY | OR_GPCM_TRLX | OR_GPCM_EHTR | \ | |
| 295 | OR_GPCM_EAD) | |
| 296 | ||
| 297 | #define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base Address */ | |
| 298 | #define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR Options */ | |
| 299 | #ifdef CONFIG_NAND_FSL_ELBC | |
| 300 | #define CONFIG_SYS_BR1_PRELIM CONFIG_SYS_NAND_BR_PRELIM /* NAND Base Addr */ | |
| 301 | #define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_NAND_OR_PRELIM /* NAND Options */ | |
| 302 | #endif | |
| 303 | ||
| 304 | /* Serial Port - controlled on board with jumper J8 | |
| 305 | * open - index 2 | |
| 306 | * shorted - index 1 | |
| 307 | */ | |
| 308 | #define CONFIG_CONS_INDEX 1 | |
| 309 | #undef CONFIG_SERIAL_SOFTWARE_FIFO | |
| 8b0044ff OZ |
310 | #define CONFIG_SYS_NS16550_SERIAL |
| 311 | #define CONFIG_SYS_NS16550_REG_SIZE 1 | |
| 312 | #define CONFIG_SYS_NS16550_CLK get_bus_freq(0) | |
| 313 | #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_INIT_MINIMAL) | |
| 314 | #define CONFIG_NS16550_MIN_FUNCTIONS | |
| 315 | #endif | |
| 316 | ||
| 317 | #define CONFIG_SYS_BAUDRATE_TABLE \ | |
| 318 | {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200} | |
| 319 | ||
| 320 | #define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR + 0x4500) | |
| 321 | #define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR + 0x4600) | |
| 322 | ||
| 8b0044ff OZ |
323 | /* I2C */ |
| 324 | #define CONFIG_SYS_I2C | |
| 325 | #define CONFIG_SYS_I2C_FSL | |
| 326 | #define CONFIG_SYS_FSL_I2C_SPEED 400000 | |
| 327 | #define CONFIG_SYS_FSL_I2C_SLAVE 0x7F | |
| 328 | #define CONFIG_SYS_FSL_I2C_OFFSET 0x3000 | |
| 329 | #define CONFIG_SYS_FSL_I2C2_SPEED 400000 | |
| 330 | #define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F | |
| 331 | #define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100 | |
| 332 | #define CONFIG_SYS_I2C_NOPROBES { {0, 0x29} } | |
| 333 | #define CONFIG_SYS_SPD_BUS_NUM 1 /* For rom_loc and flash bank */ | |
| 334 | ||
| 335 | #define CONFIG_RTC_DS1337 | |
| 336 | #define CONFIG_SYS_RTC_DS1337_NOOSC | |
| 337 | #define CONFIG_SYS_I2C_RTC_ADDR 0x68 | |
| 338 | #define CONFIG_SYS_I2C_PCA9557_ADDR 0x18 | |
| 339 | #define CONFIG_SYS_I2C_NCT72_ADDR 0x4C | |
| 340 | #define CONFIG_SYS_I2C_IDT6V49205B 0x69 | |
| 341 | ||
| 342 | /* | |
| 343 | * eSPI - Enhanced SPI | |
| 344 | */ | |
| 345 | #define CONFIG_HARD_SPI | |
| 8b0044ff | 346 | |
| 8b0044ff OZ |
347 | #define CONFIG_SF_DEFAULT_SPEED 10000000 |
| 348 | #define CONFIG_SF_DEFAULT_MODE SPI_MODE_0 | |
| 349 | ||
| 350 | #if defined(CONFIG_PCI) | |
| 351 | /* | |
| 352 | * General PCI | |
| 353 | * Memory space is mapped 1-1, but I/O space must start from 0. | |
| 354 | */ | |
| 355 | ||
| 356 | /* controller 2, direct to uli, tgtid 2, Base address 9000 */ | |
| 357 | #define CONFIG_SYS_PCIE2_NAME "PCIe SLOT CON9" | |
| 358 | #define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000 | |
| 359 | #define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000 | |
| 360 | #define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000 | |
| 361 | #define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */ | |
| 362 | #define CONFIG_SYS_PCIE2_IO_VIRT 0xffc10000 | |
| 363 | #define CONFIG_SYS_PCIE2_IO_BUS 0x00000000 | |
| 364 | #define CONFIG_SYS_PCIE2_IO_PHYS 0xffc10000 | |
| 365 | #define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */ | |
| 366 | ||
| 367 | /* controller 1, Slot 2, tgtid 1, Base address a000 */ | |
| 368 | #define CONFIG_SYS_PCIE1_NAME "PCIe SLOT CON10" | |
| 369 | #define CONFIG_SYS_PCIE1_MEM_VIRT 0x80000000 | |
| 370 | #define CONFIG_SYS_PCIE1_MEM_BUS 0x80000000 | |
| 371 | #define CONFIG_SYS_PCIE1_MEM_PHYS 0x80000000 | |
| 372 | #define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */ | |
| 373 | #define CONFIG_SYS_PCIE1_IO_VIRT 0xffc00000 | |
| 374 | #define CONFIG_SYS_PCIE1_IO_BUS 0x00000000 | |
| 375 | #define CONFIG_SYS_PCIE1_IO_PHYS 0xffc00000 | |
| 376 | #define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */ | |
| 377 | ||
| 8b0044ff | 378 | #define CONFIG_CMD_PCI |
| 8b0044ff OZ |
379 | |
| 380 | #define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */ | |
| 8b0044ff OZ |
381 | #endif /* CONFIG_PCI */ |
| 382 | ||
| 383 | /* | |
| 384 | * Environment | |
| 385 | */ | |
| 386 | #ifdef CONFIG_ENV_FIT_UCBOOT | |
| 387 | ||
| 388 | #define CONFIG_ENV_IS_IN_FLASH | |
| 389 | #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x20000) | |
| 390 | #define CONFIG_ENV_SIZE 0x20000 | |
| 391 | #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ | |
| 392 | ||
| 393 | #else | |
| 394 | ||
| 395 | #define CONFIG_ENV_SPI_BUS 0 | |
| 396 | #define CONFIG_ENV_SPI_CS 0 | |
| 397 | #define CONFIG_ENV_SPI_MAX_HZ 10000000 | |
| 398 | #define CONFIG_ENV_SPI_MODE 0 | |
| 399 | ||
| 400 | #ifdef CONFIG_RAMBOOT_SPIFLASH | |
| 401 | ||
| 402 | #define CONFIG_ENV_IS_IN_SPI_FLASH | |
| 403 | #define CONFIG_ENV_SIZE 0x3000 /* 12KB */ | |
| 404 | #define CONFIG_ENV_OFFSET 0x2000 /* 8KB */ | |
| 405 | #define CONFIG_ENV_SECT_SIZE 0x1000 | |
| 406 | ||
| 407 | #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT) | |
| 408 | /* Address and size of Redundant Environment Sector */ | |
| 409 | #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE) | |
| 410 | #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE | |
| 411 | #endif | |
| 412 | ||
| 413 | #elif defined(CONFIG_RAMBOOT_SDCARD) | |
| 414 | #define CONFIG_ENV_IS_IN_MMC | |
| 415 | #define CONFIG_FSL_FIXED_MMC_LOCATION | |
| 416 | #define CONFIG_ENV_SIZE 0x2000 | |
| 417 | #define CONFIG_SYS_MMC_ENV_DEV 0 | |
| 418 | ||
| 419 | #elif defined(CONFIG_SYS_RAMBOOT) | |
| 420 | #define CONFIG_ENV_IS_NOWHERE /* Store ENV in memory only */ | |
| 421 | #define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000) | |
| 422 | #define CONFIG_ENV_SIZE 0x2000 | |
| 423 | ||
| 424 | #else | |
| 425 | #define CONFIG_ENV_IS_IN_FLASH | |
| 426 | #define CONFIG_ENV_BASE (CONFIG_SYS_FLASH_BASE) | |
| 427 | #define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */ | |
| 428 | #define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE | |
| 429 | #define CONFIG_ENV_ADDR (CONFIG_ENV_BASE + 0xC0000) | |
| 430 | #if defined(CONFIG_SYS_REDUNDAND_ENVIRONMENT) | |
| 431 | /* Address and size of Redundant Environment Sector */ | |
| 432 | #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE) | |
| 433 | #define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE | |
| 434 | #endif | |
| 435 | ||
| 436 | #endif | |
| 437 | ||
| 438 | #endif /* CONFIG_ENV_FIT_UCBOOT */ | |
| 439 | ||
| 440 | #define CONFIG_LOADS_ECHO /* echo on for serial download */ | |
| 441 | #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ | |
| 442 | ||
| 443 | /* | |
| 444 | * Command line configuration. | |
| 445 | */ | |
| 8b0044ff | 446 | #define CONFIG_CMD_IRQ |
| 8b0044ff | 447 | #define CONFIG_CMD_DATE |
| 8b0044ff | 448 | #define CONFIG_CMD_IRQ |
| 8b0044ff OZ |
449 | #define CONFIG_CMD_REGINFO |
| 450 | #define CONFIG_CMD_ERRATA | |
| 451 | #define CONFIG_CMD_CRAMFS | |
| 8b0044ff OZ |
452 | |
| 453 | /* | |
| 454 | * USB | |
| 455 | */ | |
| 456 | #define CONFIG_HAS_FSL_DR_USB | |
| 457 | ||
| 458 | #if defined(CONFIG_HAS_FSL_DR_USB) | |
| 459 | #define CONFIG_USB_EHCI | |
| 460 | ||
| 461 | #define CONFIG_USB_MAX_CONTROLLER_COUNT 1 | |
| 462 | ||
| 463 | #ifdef CONFIG_USB_EHCI | |
| 8b0044ff OZ |
464 | #define CONFIG_EHCI_HCD_INIT_AFTER_RESET |
| 465 | #define CONFIG_USB_EHCI_FSL | |
| 8b0044ff OZ |
466 | #endif |
| 467 | #endif | |
| 468 | ||
| 469 | #undef CONFIG_WATCHDOG /* watchdog disabled */ | |
| 470 | ||
| 471 | #ifdef CONFIG_MMC | |
| 472 | #define CONFIG_FSL_ESDHC | |
| 473 | #define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR | |
| 8b0044ff OZ |
474 | #define CONFIG_MMC_SPI |
| 475 | #define CONFIG_CMD_MMC_SPI | |
| 8b0044ff OZ |
476 | #endif |
| 477 | ||
| 8b0044ff | 478 | /* Misc Extra Settings */ |
| 8b0044ff OZ |
479 | #undef CONFIG_WATCHDOG /* watchdog disabled */ |
| 480 | ||
| 481 | /* | |
| 482 | * Miscellaneous configurable options | |
| 483 | */ | |
| 484 | #define CONFIG_SYS_LONGHELP /* undef to save memory */ | |
| 485 | #define CONFIG_CMDLINE_EDITING /* Command-line editing */ | |
| 486 | #define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */ | |
| 8b0044ff OZ |
487 | #if defined(CONFIG_CMD_KGDB) |
| 488 | #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ | |
| 489 | #else | |
| 490 | #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ | |
| 491 | #endif | |
| 492 | #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) | |
| 493 | /* Print Buffer Size */ | |
| 494 | #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ | |
| 495 | #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE/* Boot Argument Buffer Size */ | |
| 496 | #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms tick */ | |
| 497 | ||
| 498 | /* | |
| 499 | * For booting Linux, the board info and command line data | |
| 500 | * have to be in the first 64 MB of memory, since this is | |
| 501 | * the maximum mapped by the Linux kernel during initialization. | |
| 502 | */ | |
| 503 | #define CONFIG_SYS_BOOTMAPSZ (64 << 20) /* Initial Memory for Linux*/ | |
| 504 | #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ | |
| 505 | ||
| 506 | #if defined(CONFIG_CMD_KGDB) | |
| 507 | #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */ | |
| 508 | #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ | |
| 509 | #endif | |
| 510 | ||
| 511 | /* | |
| 512 | * Environment Configuration | |
| 513 | */ | |
| 514 | ||
| 515 | #if defined(CONFIG_TSEC_ENET) | |
| 516 | ||
| 517 | #if defined(CONFIG_UCP1020_REV_1_2) | |
| 518 | #define CONFIG_PHY_MICREL_KSZ9021 | |
| 519 | #elif defined(CONFIG_UCP1020_REV_1_3) | |
| 520 | #define CONFIG_PHY_MICREL_KSZ9031 | |
| 521 | #else | |
| 522 | #error "UCP1020 module revision is not defined !!!" | |
| 523 | #endif | |
| 524 | ||
| 8b0044ff OZ |
525 | #define CONFIG_BOOTP_SERVERIP |
| 526 | ||
| 527 | #define CONFIG_MII /* MII PHY management */ | |
| 528 | #define CONFIG_TSEC1_NAME "eTSEC1" | |
| 529 | #define CONFIG_TSEC2_NAME "eTSEC2" | |
| 530 | #define CONFIG_TSEC3_NAME "eTSEC3" | |
| 531 | ||
| 532 | #define TSEC1_PHY_ADDR 4 | |
| 533 | #define TSEC2_PHY_ADDR 0 | |
| 534 | #define TSEC2_PHY_ADDR_SGMII 0x00 | |
| 535 | #define TSEC3_PHY_ADDR 6 | |
| 536 | ||
| 537 | #define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) | |
| 538 | #define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) | |
| 539 | #define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED) | |
| 540 | ||
| 541 | #define TSEC1_PHYIDX 0 | |
| 542 | #define TSEC2_PHYIDX 0 | |
| 543 | #define TSEC3_PHYIDX 0 | |
| 544 | ||
| 545 | #define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */ | |
| 546 | ||
| 547 | #endif | |
| 548 | ||
| 549 | #define CONFIG_HOSTNAME UCP1020 | |
| 550 | #define CONFIG_ROOTPATH "/opt/nfsroot" | |
| 551 | #define CONFIG_BOOTFILE "uImage" | |
| 552 | #define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image on TFTP server */ | |
| 553 | ||
| 554 | /* default location for tftp and bootm */ | |
| 555 | #define CONFIG_LOADADDR 1000000 | |
| 556 | ||
| 8b0044ff OZ |
557 | #define CONFIG_BOOTARGS /* the boot command will set bootargs */ |
| 558 | ||
| 559 | #define CONFIG_BAUDRATE 115200 | |
| 560 | ||
| 561 | #if defined(CONFIG_DONGLE) | |
| 562 | ||
| 8b0044ff OZ |
563 | #define CONFIG_EXTRA_ENV_SETTINGS \ |
| 564 | "bootcmd=run prog_spi_mbrbootcramfs\0" \ | |
| 565 | "bootfile=uImage\0" \ | |
| 566 | "consoledev=ttyS0\0" \ | |
| 567 | "cramfsfile=image.cramfs\0" \ | |
| 568 | "dtbaddr=0x00c00000\0" \ | |
| 569 | "dtbfile=image.dtb\0" \ | |
| 570 | "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \ | |
| 571 | "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \ | |
| 572 | "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \ | |
| 573 | "fileaddr=0x01000000\0" \ | |
| 574 | "filesize=0x00080000\0" \ | |
| 575 | "flashmbr=sf probe 0; " \ | |
| 576 | "tftp $loadaddr $mbr; " \ | |
| 577 | "sf erase $mbr_offset +$filesize; " \ | |
| 578 | "sf write $loadaddr $mbr_offset $filesize\0" \ | |
| 579 | "flashrecovery=tftp $recoveryaddr $cramfsfile; " \ | |
| 580 | "protect off $nor_recoveryaddr +$filesize; " \ | |
| 581 | "erase $nor_recoveryaddr +$filesize; " \ | |
| 582 | "cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \ | |
| 583 | "protect on $nor_recoveryaddr +$filesize\0 " \ | |
| 584 | "flashuboot=tftp $ubootaddr $ubootfile; " \ | |
| 585 | "protect off $nor_ubootaddr +$filesize; " \ | |
| 586 | "erase $nor_ubootaddr +$filesize; " \ | |
| 587 | "cp.b $ubootaddr $nor_ubootaddr $filesize; " \ | |
| 588 | "protect on $nor_ubootaddr +$filesize\0 " \ | |
| 589 | "flashworking=tftp $workingaddr $cramfsfile; " \ | |
| 590 | "protect off $nor_workingaddr +$filesize; " \ | |
| 591 | "erase $nor_workingaddr +$filesize; " \ | |
| 592 | "cp.b $workingaddr $nor_workingaddr $filesize; " \ | |
| 593 | "protect on $nor_workingaddr +$filesize\0 " \ | |
| 594 | "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \ | |
| 595 | "kerneladdr=0x01100000\0" \ | |
| 596 | "kernelfile=uImage\0" \ | |
| 597 | "loadaddr=0x01000000\0" \ | |
| 598 | "mbr=uCP1020d.mbr\0" \ | |
| 599 | "mbr_offset=0x00000000\0" \ | |
| 600 | "mmbr=uCP1020Quiet.mbr\0" \ | |
| 601 | "mmcpart=0:2\0" \ | |
| 602 | "mmc__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \ | |
| 603 | "mmc erase 1 1; " \ | |
| 604 | "mmc write $loadaddr 1 1\0" \ | |
| 605 | "mmc__uboot=fatload mmc $mmcpart $loadaddr $ubootfile; " \ | |
| 606 | "mmc erase 0x40 0x400; " \ | |
| 607 | "mmc write $loadaddr 0x40 0x400\0" \ | |
| 608 | "netdev=eth0\0" \ | |
| 609 | "nor_recoveryaddr=0xEC0A0000\0" \ | |
| 610 | "nor_ubootaddr=0xEFF80000\0" \ | |
| 611 | "nor_workingaddr=0xECFA0000\0" \ | |
| 612 | "norbootrecovery=setenv bootargs $recoverybootargs" \ | |
| 613 | " console=$consoledev,$baudrate $othbootargs; " \ | |
| 614 | "run norloadrecovery; " \ | |
| 615 | "bootm $kerneladdr - $dtbaddr\0" \ | |
| 616 | "norbootworking=setenv bootargs $workingbootargs" \ | |
| 617 | " console=$consoledev,$baudrate $othbootargs; " \ | |
| 618 | "run norloadworking; " \ | |
| 619 | "bootm $kerneladdr - $dtbaddr\0" \ | |
| 620 | "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \ | |
| 621 | "setenv cramfsaddr $nor_recoveryaddr; " \ | |
| 622 | "cramfsload $dtbaddr $dtbfile; " \ | |
| 623 | "cramfsload $kerneladdr $kernelfile\0" \ | |
| 624 | "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \ | |
| 625 | "setenv cramfsaddr $nor_workingaddr; " \ | |
| 626 | "cramfsload $dtbaddr $dtbfile; " \ | |
| 627 | "cramfsload $kerneladdr $kernelfile\0" \ | |
| 628 | "prog_spi_mbr=run spi__mbr\0" \ | |
| 629 | "prog_spi_mbrboot=run spi__mbr; run spi__boot1; run spi__boot2\0" \ | |
| 630 | "prog_spi_mbrbootcramfs=run spi__mbr; run spi__boot1; run spi__boot2; " \ | |
| 631 | "run spi__cramfs\0" \ | |
| 632 | "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \ | |
| 633 | " console=$consoledev,$baudrate $othbootargs; " \ | |
| 634 | "tftp $rootfsaddr $rootfsfile; " \ | |
| 635 | "tftp $loadaddr $kernelfile; " \ | |
| 636 | "tftp $dtbaddr $dtbfile; " \ | |
| 637 | "bootm $loadaddr $rootfsaddr $dtbaddr\0" \ | |
| 638 | "ramdisk_size=120000\0" \ | |
| 639 | "ramdiskfile=rootfs.ext2.gz.uboot\0" \ | |
| 640 | "recoveryaddr=0x02F00000\0" \ | |
| 641 | "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \ | |
| 642 | "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \ | |
| 643 | "mw.l 0xffe0f008 0x00400000\0" \ | |
| 644 | "rootfsaddr=0x02F00000\0" \ | |
| 645 | "rootfsfile=rootfs.ext2.gz.uboot\0" \ | |
| 646 | "rootpath=/opt/nfsroot\0" \ | |
| 647 | "spi__boot1=fatload mmc $mmcpart $loadaddr u-boot.bin; " \ | |
| 648 | "protect off 0xeC000000 +$filesize; " \ | |
| 649 | "erase 0xEC000000 +$filesize; " \ | |
| 650 | "cp.b $loadaddr 0xEC000000 $filesize; " \ | |
| 651 | "cmp.b $loadaddr 0xEC000000 $filesize; " \ | |
| 652 | "protect on 0xeC000000 +$filesize\0" \ | |
| 653 | "spi__boot2=fatload mmc $mmcpart $loadaddr u-boot.bin; " \ | |
| 654 | "protect off 0xeFF80000 +$filesize; " \ | |
| 655 | "erase 0xEFF80000 +$filesize; " \ | |
| 656 | "cp.b $loadaddr 0xEFF80000 $filesize; " \ | |
| 657 | "cmp.b $loadaddr 0xEFF80000 $filesize; " \ | |
| 658 | "protect on 0xeFF80000 +$filesize\0" \ | |
| 659 | "spi__bootd=fatload mmc $mmcpart $loadaddr $ubootd; " \ | |
| 660 | "sf probe 0; sf erase 0x8000 +$filesize; " \ | |
| 661 | "sf write $loadaddr 0x8000 $filesize\0" \ | |
| 662 | "spi__cramfs=fatload mmc $mmcpart $loadaddr image.cramfs; " \ | |
| 663 | "protect off 0xec0a0000 +$filesize; " \ | |
| 664 | "erase 0xeC0A0000 +$filesize; " \ | |
| 665 | "cp.b $loadaddr 0xeC0A0000 $filesize; " \ | |
| 666 | "protect on 0xec0a0000 +$filesize\0" \ | |
| 667 | "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \ | |
| 668 | "sf probe 1; sf erase 0 +$filesize; " \ | |
| 669 | "sf write $loadaddr 0 $filesize\0" \ | |
| 670 | "spi__mbrd=fatload mmc $mmcpart $loadaddr $mbr; " \ | |
| 671 | "sf probe 0; sf erase 0 +$filesize; " \ | |
| 672 | "sf write $loadaddr 0 $filesize\0" \ | |
| 673 | "tftpflash=tftpboot $loadaddr $uboot; " \ | |
| 674 | "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ | |
| 675 | "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ | |
| 676 | "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \ | |
| 677 | "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ | |
| 678 | "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\ | |
| 679 | "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \ | |
| 680 | "ubootaddr=0x01000000\0" \ | |
| 681 | "ubootfile=u-boot.bin\0" \ | |
| 682 | "ubootd=u-boot4dongle.bin\0" \ | |
| 683 | "upgrade=run flashworking\0" \ | |
| 684 | "usb_phy_type=ulpi\0 " \ | |
| 685 | "workingaddr=0x02F00000\0" \ | |
| 686 | "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" | |
| 687 | ||
| 688 | #else | |
| 689 | ||
| 690 | #if defined(CONFIG_UCP1020T1) | |
| 691 | ||
| 8b0044ff OZ |
692 | #define CONFIG_EXTRA_ENV_SETTINGS \ |
| 693 | "bootcmd=run releasefpga; run norbootworking || run norbootrecovery\0" \ | |
| 694 | "bootfile=uImage\0" \ | |
| 695 | "consoledev=ttyS0\0" \ | |
| 696 | "cramfsfile=image.cramfs\0" \ | |
| 697 | "dtbaddr=0x00c00000\0" \ | |
| 698 | "dtbfile=image.dtb\0" \ | |
| 699 | "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \ | |
| 700 | "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \ | |
| 701 | "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \ | |
| 702 | "fileaddr=0x01000000\0" \ | |
| 703 | "filesize=0x00080000\0" \ | |
| 704 | "flashmbr=sf probe 0; " \ | |
| 705 | "tftp $loadaddr $mbr; " \ | |
| 706 | "sf erase $mbr_offset +$filesize; " \ | |
| 707 | "sf write $loadaddr $mbr_offset $filesize\0" \ | |
| 708 | "flashrecovery=tftp $recoveryaddr $cramfsfile; " \ | |
| 709 | "protect off $nor_recoveryaddr +$filesize; " \ | |
| 710 | "erase $nor_recoveryaddr +$filesize; " \ | |
| 711 | "cp.b $recoveryaddr $nor_recoveryaddr $filesize; " \ | |
| 712 | "protect on $nor_recoveryaddr +$filesize\0 " \ | |
| 713 | "flashuboot=tftp $ubootaddr $ubootfile; " \ | |
| 714 | "protect off $nor_ubootaddr +$filesize; " \ | |
| 715 | "erase $nor_ubootaddr +$filesize; " \ | |
| 716 | "cp.b $ubootaddr $nor_ubootaddr $filesize; " \ | |
| 717 | "protect on $nor_ubootaddr +$filesize\0 " \ | |
| 718 | "flashworking=tftp $workingaddr $cramfsfile; " \ | |
| 719 | "protect off $nor_workingaddr +$filesize; " \ | |
| 720 | "erase $nor_workingaddr +$filesize; " \ | |
| 721 | "cp.b $workingaddr $nor_workingaddr $filesize; " \ | |
| 722 | "protect on $nor_workingaddr +$filesize\0 " \ | |
| 723 | "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \ | |
| 724 | "kerneladdr=0x01100000\0" \ | |
| 725 | "kernelfile=uImage\0" \ | |
| 726 | "loadaddr=0x01000000\0" \ | |
| 727 | "mbr=uCP1020.mbr\0" \ | |
| 728 | "mbr_offset=0x00000000\0" \ | |
| 729 | "netdev=eth0\0" \ | |
| 730 | "nor_recoveryaddr=0xEC0A0000\0" \ | |
| 731 | "nor_ubootaddr=0xEFF80000\0" \ | |
| 732 | "nor_workingaddr=0xECFA0000\0" \ | |
| 733 | "norbootrecovery=setenv bootargs $recoverybootargs" \ | |
| 734 | " console=$consoledev,$baudrate $othbootargs; " \ | |
| 735 | "run norloadrecovery; " \ | |
| 736 | "bootm $kerneladdr - $dtbaddr\0" \ | |
| 737 | "norbootworking=setenv bootargs $workingbootargs" \ | |
| 738 | " console=$consoledev,$baudrate $othbootargs; " \ | |
| 739 | "run norloadworking; " \ | |
| 740 | "bootm $kerneladdr - $dtbaddr\0" \ | |
| 741 | "norloadrecovery=mw.l $kerneladdr 0x0 0x00a00000; " \ | |
| 742 | "setenv cramfsaddr $nor_recoveryaddr; " \ | |
| 743 | "cramfsload $dtbaddr $dtbfile; " \ | |
| 744 | "cramfsload $kerneladdr $kernelfile\0" \ | |
| 745 | "norloadworking=mw.l $kerneladdr 0x0 0x00a00000; " \ | |
| 746 | "setenv cramfsaddr $nor_workingaddr; " \ | |
| 747 | "cramfsload $dtbaddr $dtbfile; " \ | |
| 748 | "cramfsload $kerneladdr $kernelfile\0" \ | |
| 749 | "othbootargs=quiet\0" \ | |
| 750 | "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \ | |
| 751 | " console=$consoledev,$baudrate $othbootargs; " \ | |
| 752 | "tftp $rootfsaddr $rootfsfile; " \ | |
| 753 | "tftp $loadaddr $kernelfile; " \ | |
| 754 | "tftp $dtbaddr $dtbfile; " \ | |
| 755 | "bootm $loadaddr $rootfsaddr $dtbaddr\0" \ | |
| 756 | "ramdisk_size=120000\0" \ | |
| 757 | "ramdiskfile=rootfs.ext2.gz.uboot\0" \ | |
| 758 | "recoveryaddr=0x02F00000\0" \ | |
| 759 | "recoverybootargs=root=/dev/mtdblock0 rootfstype=cramfs ro\0" \ | |
| 760 | "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \ | |
| 761 | "mw.l 0xffe0f008 0x00400000\0" \ | |
| 762 | "rootfsaddr=0x02F00000\0" \ | |
| 763 | "rootfsfile=rootfs.ext2.gz.uboot\0" \ | |
| 764 | "rootpath=/opt/nfsroot\0" \ | |
| 765 | "silent=1\0" \ | |
| 766 | "tftpflash=tftpboot $loadaddr $uboot; " \ | |
| 767 | "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ | |
| 768 | "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ | |
| 769 | "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \ | |
| 770 | "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ | |
| 771 | "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\ | |
| 772 | "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \ | |
| 773 | "ubootaddr=0x01000000\0" \ | |
| 774 | "ubootfile=u-boot.bin\0" \ | |
| 775 | "upgrade=run flashworking\0" \ | |
| 776 | "workingaddr=0x02F00000\0" \ | |
| 777 | "workingbootargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" | |
| 778 | ||
| 779 | #else /* For Arcturus Modules */ | |
| 780 | ||
| 8b0044ff OZ |
781 | #define CONFIG_EXTRA_ENV_SETTINGS \ |
| 782 | "bootcmd=run norkernel\0" \ | |
| 783 | "bootfile=uImage\0" \ | |
| 784 | "consoledev=ttyS0\0" \ | |
| 785 | "dtbaddr=0x00c00000\0" \ | |
| 786 | "dtbfile=image.dtb\0" \ | |
| 787 | "ethaddr=" __stringify(CONFIG_ETHADDR) "\0" \ | |
| 788 | "eth1addr=" __stringify(CONFIG_ETH1ADDR) "\0" \ | |
| 789 | "eth2addr=" __stringify(CONFIG_ETH2ADDR) "\0" \ | |
| 790 | "fileaddr=0x01000000\0" \ | |
| 791 | "filesize=0x00080000\0" \ | |
| 792 | "flashmbr=sf probe 0; " \ | |
| 793 | "tftp $loadaddr $mbr; " \ | |
| 794 | "sf erase $mbr_offset +$filesize; " \ | |
| 795 | "sf write $loadaddr $mbr_offset $filesize\0" \ | |
| 796 | "flashuboot=tftp $loadaddr $ubootfile; " \ | |
| 797 | "protect off $nor_ubootaddr0 +$filesize; " \ | |
| 798 | "erase $nor_ubootaddr0 +$filesize; " \ | |
| 799 | "cp.b $loadaddr $nor_ubootaddr0 $filesize; " \ | |
| 800 | "protect on $nor_ubootaddr0 +$filesize; " \ | |
| 801 | "protect off $nor_ubootaddr1 +$filesize; " \ | |
| 802 | "erase $nor_ubootaddr1 +$filesize; " \ | |
| 803 | "cp.b $loadaddr $nor_ubootaddr1 $filesize; " \ | |
| 804 | "protect on $nor_ubootaddr1 +$filesize\0 " \ | |
| 805 | "format0=protect off $part0base +$part0size; " \ | |
| 806 | "erase $part0base +$part0size\0" \ | |
| 807 | "format1=protect off $part1base +$part1size; " \ | |
| 808 | "erase $part1base +$part1size\0" \ | |
| 809 | "format2=protect off $part2base +$part2size; " \ | |
| 810 | "erase $part2base +$part2size\0" \ | |
| 811 | "format3=protect off $part3base +$part3size; " \ | |
| 812 | "erase $part3base +$part3size\0" \ | |
| 813 | "hwconfig=usb1:dr_mode=host,phy_type=ulpi\0 " \ | |
| 814 | "kerneladdr=0x01100000\0" \ | |
| 815 | "kernelargs=root=/dev/mtdblock1 rootfstype=cramfs ro\0" \ | |
| 816 | "kernelfile=uImage\0" \ | |
| 817 | "loadaddr=0x01000000\0" \ | |
| 818 | "mbr=uCP1020.mbr\0" \ | |
| 819 | "mbr_offset=0x00000000\0" \ | |
| 820 | "netdev=eth0\0" \ | |
| 821 | "nor_ubootaddr0=0xEC000000\0" \ | |
| 822 | "nor_ubootaddr1=0xEFF80000\0" \ | |
| 823 | "norkernel=setenv bootargs $kernelargs console=$consoledev,$baudrate; " \ | |
| 824 | "run norkernelload; " \ | |
| 825 | "bootm $kerneladdr - $dtbaddr\0" \ | |
| 826 | "norkernelload=mw.l $kerneladdr 0x0 0x00a00000; " \ | |
| 827 | "setenv cramfsaddr $part0base; " \ | |
| 828 | "cramfsload $dtbaddr $dtbfile; " \ | |
| 829 | "cramfsload $kerneladdr $kernelfile\0" \ | |
| 830 | "part0base=0xEC100000\0" \ | |
| 831 | "part0size=0x00700000\0" \ | |
| 832 | "part1base=0xEC800000\0" \ | |
| 833 | "part1size=0x02000000\0" \ | |
| 834 | "part2base=0xEE800000\0" \ | |
| 835 | "part2size=0x00800000\0" \ | |
| 836 | "part3base=0xEF000000\0" \ | |
| 837 | "part3size=0x00F80000\0" \ | |
| 838 | "partENVbase=0xEC080000\0" \ | |
| 839 | "partENVsize=0x00080000\0" \ | |
| 840 | "program0=tftp part0-000000.bin; " \ | |
| 841 | "protect off $part0base +$filesize; " \ | |
| 842 | "erase $part0base +$filesize; " \ | |
| 843 | "cp.b $loadaddr $part0base $filesize; " \ | |
| 844 | "echo Verifying...; " \ | |
| 845 | "cmp.b $loadaddr $part0base $filesize\0" \ | |
| 846 | "program1=tftp part1-000000.bin; " \ | |
| 847 | "protect off $part1base +$filesize; " \ | |
| 848 | "erase $part1base +$filesize; " \ | |
| 849 | "cp.b $loadaddr $part1base $filesize; " \ | |
| 850 | "echo Verifying...; " \ | |
| 851 | "cmp.b $loadaddr $part1base $filesize\0" \ | |
| 852 | "program2=tftp part2-000000.bin; " \ | |
| 853 | "protect off $part2base +$filesize; " \ | |
| 854 | "erase $part2base +$filesize; " \ | |
| 855 | "cp.b $loadaddr $part2base $filesize; " \ | |
| 856 | "echo Verifying...; " \ | |
| 857 | "cmp.b $loadaddr $part2base $filesize\0" \ | |
| 858 | "ramboot=setenv bootargs root=/dev/ram ramdisk_size=$ramdisk_size ro" \ | |
| 859 | " console=$consoledev,$baudrate $othbootargs; " \ | |
| 860 | "tftp $rootfsaddr $rootfsfile; " \ | |
| 861 | "tftp $loadaddr $kernelfile; " \ | |
| 862 | "tftp $dtbaddr $dtbfile; " \ | |
| 863 | "bootm $loadaddr $rootfsaddr $dtbaddr\0" \ | |
| 864 | "ramdisk_size=120000\0" \ | |
| 865 | "ramdiskfile=rootfs.ext2.gz.uboot\0" \ | |
| 866 | "releasefpga=mw.l 0xffe0f000 0x00400000; mw.l 0xffe0f004 0x00000000; " \ | |
| 867 | "mw.l 0xffe0f008 0x00400000\0" \ | |
| 868 | "rootfsaddr=0x02F00000\0" \ | |
| 869 | "rootfsfile=rootfs.ext2.gz.uboot\0" \ | |
| 870 | "rootpath=/opt/nfsroot\0" \ | |
| 871 | "spi__mbr=fatload mmc $mmcpart $loadaddr $mmbr; " \ | |
| 872 | "sf probe 0; sf erase 0 +$filesize; " \ | |
| 873 | "sf write $loadaddr 0 $filesize\0" \ | |
| 874 | "spi__boot=fatload mmc $mmcpart $loadaddr u-boot.bin; " \ | |
| 875 | "protect off 0xeC000000 +$filesize; " \ | |
| 876 | "erase 0xEC000000 +$filesize; " \ | |
| 877 | "cp.b $loadaddr 0xEC000000 $filesize; " \ | |
| 878 | "cmp.b $loadaddr 0xEC000000 $filesize; " \ | |
| 879 | "protect on 0xeC000000 +$filesize\0" \ | |
| 880 | "tftpflash=tftpboot $loadaddr $uboot; " \ | |
| 881 | "protect off " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ | |
| 882 | "erase " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ | |
| 883 | "cp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize; " \ | |
| 884 | "protect on " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " +$filesize; " \ | |
| 885 | "cmp.b $loadaddr " __stringify(CONFIG_SYS_TEXT_BASE_NOR) " $filesize\0"\ | |
| 886 | "uboot= " __stringify(CONFIG_UBOOTPATH) "\0" \ | |
| 887 | "ubootfile=u-boot.bin\0" \ | |
| 888 | "upgrade=run flashuboot\0" \ | |
| 889 | "usb_phy_type=ulpi\0 " \ | |
| 890 | "boot_nfs= " \ | |
| 891 | "setenv bootargs root=/dev/nfs rw " \ | |
| 892 | "nfsroot=$serverip:$rootpath " \ | |
| 893 | "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \ | |
| 894 | "console=$consoledev,$baudrate $othbootargs;" \ | |
| 895 | "tftp $loadaddr $bootfile;" \ | |
| 896 | "tftp $fdtaddr $fdtfile;" \ | |
| 897 | "bootm $loadaddr - $fdtaddr\0" \ | |
| 898 | "boot_hd = " \ | |
| 899 | "setenv bootargs root=/dev/$bdev rw rootdelay=30 " \ | |
| 900 | "console=$consoledev,$baudrate $othbootargs;" \ | |
| 901 | "usb start;" \ | |
| 902 | "ext2load usb 0:1 $loadaddr /boot/$bootfile;" \ | |
| 903 | "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \ | |
| 904 | "bootm $loadaddr - $fdtaddr\0" \ | |
| 905 | "boot_usb_fat = " \ | |
| 906 | "setenv bootargs root=/dev/ram rw " \ | |
| 907 | "console=$consoledev,$baudrate $othbootargs " \ | |
| 908 | "ramdisk_size=$ramdisk_size;" \ | |
| 909 | "usb start;" \ | |
| 910 | "fatload usb 0:2 $loadaddr $bootfile;" \ | |
| 911 | "fatload usb 0:2 $fdtaddr $fdtfile;" \ | |
| 912 | "fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \ | |
| 913 | "bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \ | |
| 914 | "boot_usb_ext2 = " \ | |
| 915 | "setenv bootargs root=/dev/ram rw " \ | |
| 916 | "console=$consoledev,$baudrate $othbootargs " \ | |
| 917 | "ramdisk_size=$ramdisk_size;" \ | |
| 918 | "usb start;" \ | |
| 919 | "ext2load usb 0:4 $loadaddr $bootfile;" \ | |
| 920 | "ext2load usb 0:4 $fdtaddr $fdtfile;" \ | |
| 921 | "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \ | |
| 922 | "bootm $loadaddr $ramdiskaddr $fdtaddr\0 " \ | |
| 923 | "boot_nor = " \ | |
| 924 | "setenv bootargs root=/dev/$jffs2nor rw " \ | |
| 925 | "console=$consoledev,$baudrate rootfstype=jffs2 $othbootargs;" \ | |
| 926 | "bootm $norbootaddr - $norfdtaddr\0 " \ | |
| 927 | "boot_ram = " \ | |
| 928 | "setenv bootargs root=/dev/ram rw " \ | |
| 929 | "console=$consoledev,$baudrate $othbootargs " \ | |
| 930 | "ramdisk_size=$ramdisk_size;" \ | |
| 931 | "tftp $ramdiskaddr $ramdiskfile;" \ | |
| 932 | "tftp $loadaddr $bootfile;" \ | |
| 933 | "tftp $fdtaddr $fdtfile;" \ | |
| 934 | "bootm $loadaddr $ramdiskaddr $fdtaddr\0" | |
| 935 | ||
| 936 | #endif | |
| 937 | #endif | |
| 938 | ||
| 939 | #endif /* __CONFIG_H */ |