[people/ms/u-boot.git] / include / configs / ZPC1900.h

/*
 * Copyright (C) 2003-2005 Arabella Software Ltd.
 * Yuli Barcohen <yuli@arabellasw.com>
 *
 * U-Boot configuration for Zephyr Engineering ZPC.1900 board.
 * This port was developed and tested on Revision C board.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

#define CONFIG_MPC8260		1	/* This is an MPC8260 CPU      */
#define CONFIG_ZPC1900		1	/* ...on Zephyr ZPC.1900 board */

#define	CONFIG_SYS_TEXT_BASE	0xFE000000

#define CPU_ID_STR		"MPC8265"
#define CONFIG_CPM2		1	/* Has a CPM2 */

/* Allow serial number (serial#) and MAC address (ethaddr) to be overwritten */
#define CONFIG_ENV_OVERWRITE

/*
 * Select serial console configuration
 *
 * If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
 * CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
 * for SCC).
 */
#define	CONFIG_CONS_ON_SMC		/* Console is on SMC         */
#undef  CONFIG_CONS_ON_SCC		/* It's not on SCC           */
#undef	CONFIG_CONS_NONE		/* It's not on external UART */
#define CONFIG_CONS_INDEX	1	/* SMC1 is used for console  */

/*
 * Select ethernet configuration
 *
 * If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected,
 * then CONFIG_ETHER_INDEX must be set to the channel number (1-4 for
 * SCC, 1-3 for FCC)
 *
 * If CONFIG_ETHER_NONE is defined, then either the ethernet routines
 * must be defined elsewhere (as for the console), or CONFIG_CMD_NET
 * must be unset.
 */
#undef	CONFIG_ETHER_ON_SCC		/* Ethernet is not on SCC */
#define CONFIG_ETHER_ON_FCC		/* Ethernet is on FCC     */
#undef	CONFIG_ETHER_NONE		/* No external Ethernet   */

#ifdef CONFIG_ETHER_ON_FCC

#define CONFIG_ETHER_INDEX	2	/* FCC2 is used for Ethernet */

#if (CONFIG_ETHER_INDEX == 2)
/*
 * - Rx clock is CLK13
 * - Tx clock is CLK14
 * - Select bus for bd/buffers (see 28-13)
 * - Full duplex
 */
# define CONFIG_SYS_CMXFCR_MASK2	(CMXFCR_FC2 | CMXFCR_RF2CS_MSK | CMXFCR_TF2CS_MSK)
# define CONFIG_SYS_CMXFCR_VALUE2	(CMXFCR_RF2CS_CLK13 | CMXFCR_TF2CS_CLK14)
# define CONFIG_SYS_CPMFCR_RAMTYPE	0
# define CONFIG_SYS_FCC_PSMR		(FCC_PSMR_FDE | FCC_PSMR_LPB)

#endif /* CONFIG_ETHER_INDEX */

#define CONFIG_MII			/* MII PHY management        */
#define CONFIG_BITBANGMII		/* Bit-banged MDIO interface */
/*
 * GPIO pins used for bit-banged MII communications
 */
#define MDIO_PORT		2	/* Port C */
#define MDIO_DECLARE		volatile ioport_t *iop = ioport_addr ( \
					(immap_t *) CONFIG_SYS_IMMR, MDIO_PORT )
#define MDC_DECLARE		MDIO_DECLARE

#define MDIO_ACTIVE		(iop->pdir |=  0x00400000)
#define MDIO_TRISTATE		(iop->pdir &= ~0x00400000)
#define MDIO_READ		((iop->pdat &  0x00400000) != 0)

#define MDIO(bit)		if(bit) iop->pdat |=  0x00400000; \
				else	iop->pdat &= ~0x00400000

#define MDC(bit)		if(bit) iop->pdat |=  0x00200000; \
				else	iop->pdat &= ~0x00200000

#define MIIDELAY		udelay(1)

#endif /* CONFIG_ETHER_ON_FCC */

#ifndef CONFIG_8260_CLKIN
#define CONFIG_8260_CLKIN	66666666	/* in Hz */
#endif

#define CONFIG_BAUDRATE		38400


/*
 * BOOTP options
 */
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME


/*
 * Command line configuration.
 */
#include <config_cmd_default.h>

#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_IMMAP
#define CONFIG_CMD_MII
#define CONFIG_CMD_PING


#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */
#define CONFIG_BOOTCOMMAND	"dhcp;bootm"	/* autoboot command */
#define CONFIG_BOOTARGS		"root=/dev/nfs rw ip=:::::eth0:dhcp"

#if defined(CONFIG_CMD_KGDB)
#undef	CONFIG_KGDB_ON_SMC		/* define if kgdb on SMC */
#define CONFIG_KGDB_ON_SCC		/* define if kgdb on SCC */
#undef	CONFIG_KGDB_NONE		/* define if kgdb on something else */
#define CONFIG_KGDB_INDEX	2	/* which serial channel for kgdb */
#define CONFIG_KGDB_BAUDRATE	115200	/* speed to run kgdb serial port at */
#endif

#define CONFIG_BZIP2	/* include support for bzip2 compressed images */
#undef	CONFIG_WATCHDOG			/* disable platform specific watchdog */

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_LONGHELP			/* undef to save memory	    */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
#else
#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size  */
#define CONFIG_SYS_MAXARGS		16		/* max number of command args */
#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size  */

#define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on */
#define CONFIG_SYS_MEMTEST_END		0x03800000	/* 1 ... 56 MB in DRAM	*/

#define CONFIG_SYS_LOAD_ADDR		0x400000	/* default load address */

#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }

#define CONFIG_SYS_SDRAM_BASE		0x00000000
#define CONFIG_SYS_SDRAM_SIZE		64

#define CONFIG_SYS_IMMR		0xF0000000
#define CONFIG_SYS_LSDRAM_BASE		0xFC000000
#define CONFIG_SYS_FLASH_BASE		0xFE000000
#define CONFIG_SYS_BCSR		0xFEA00000
#define CONFIG_SYS_EEPROM		0xFEB00000
#define CONFIG_SYS_FLSIMM_BASE		0xFF000000

#define CONFIG_SYS_FLASH_CFI
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_MAX_FLASH_BANKS	2	/* max num of flash banks	*/
#define CONFIG_SYS_MAX_FLASH_SECT	32	/* max num of sects on one chip */

#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLSIMM_BASE }

#define BCSR_PCI_MODE		0x01

#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
#define CONFIG_SYS_INIT_RAM_SIZE	0x4000	/* Size of used area in DPRAM	*/
#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

/* Hard reset configuration word */
#define CONFIG_SYS_HRCW_MASTER		(HRCW_EBM | HRCW_BPS01| HRCW_CIP          |\
				 HRCW_L2CPC10 | HRCW_DPPC00 | HRCW_ISB100 |\
				 HRCW_BMS | HRCW_LBPC00 | HRCW_APPC10     |\
				 HRCW_MODCK_H0111                          \
				) /* 0x16848207 */
/* No slaves */
#define CONFIG_SYS_HRCW_SLAVE1		0
#define CONFIG_SYS_HRCW_SLAVE2		0
#define CONFIG_SYS_HRCW_SLAVE3		0
#define CONFIG_SYS_HRCW_SLAVE4		0
#define CONFIG_SYS_HRCW_SLAVE5		0
#define CONFIG_SYS_HRCW_SLAVE6		0
#define CONFIG_SYS_HRCW_SLAVE7		0

#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE

#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#define CONFIG_SYS_RAMBOOT
#endif

#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
#define CONFIG_SYS_MALLOC_LEN		(4096 << 10)	/* Reserve 4 MB for malloc()	*/
#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */

#if !defined(CONFIG_ENV_IS_IN_FLASH) && !defined(CONFIG_ENV_IS_IN_NVRAM)
#define CONFIG_ENV_IS_IN_NVRAM	1
#endif

#ifdef CONFIG_ENV_IS_IN_FLASH
#  define CONFIG_ENV_SECT_SIZE	0x10000
#  define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
#else
#  define CONFIG_ENV_ADDR		(CONFIG_SYS_EEPROM + 0x400)
#  define CONFIG_ENV_SIZE		0x1000
#  define CONFIG_SYS_NVRAM_ACCESS_ROUTINE
#endif

#define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC8260 CPU */
#if defined(CONFIG_CMD_KGDB)
#  define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
#endif

#define CONFIG_SYS_HID0_INIT		(HID0_ICFI)
#define CONFIG_SYS_HID0_FINAL		(HID0_ICE | HID0_IFEM | HID0_ABE)

#define CONFIG_SYS_HID2		0

#define CONFIG_SYS_SIUMCR		0x42200000
#define CONFIG_SYS_SYPCR		0xFFFFFFC3
#define CONFIG_SYS_BCR			0x90000000
#define CONFIG_SYS_SCCR		SCCR_DFBRG01

#define CONFIG_SYS_RMR			RMR_CSRE
#define CONFIG_SYS_TMCNTSC		(TMCNTSC_SEC|TMCNTSC_ALR|TMCNTSC_TCF|TMCNTSC_TCE)
#define CONFIG_SYS_PISCR		(PISCR_PS|PISCR_PTF|PISCR_PTE)
#define CONFIG_SYS_RCCR		0

#define CONFIG_SYS_PSDMR		/* 0x834DA43B */0x014DA43A
#define CONFIG_SYS_PSRT		0x0F/* 0x0C */
#define CONFIG_SYS_LSDMR		0x0085A562
#define CONFIG_SYS_LSRT		0x0F
#define CONFIG_SYS_MPTPR		0x4000

#define CONFIG_SYS_PSDRAM_BR		(CONFIG_SYS_SDRAM_BASE | 0x00000041)
#define CONFIG_SYS_PSDRAM_OR		0xFC0028C0
#define CONFIG_SYS_LSDRAM_BR		(CONFIG_SYS_LSDRAM_BASE | 0x00001861)
#define CONFIG_SYS_LSDRAM_OR		0xFF803480

#define CONFIG_SYS_BR0_PRELIM		(CONFIG_SYS_FLASH_BASE | 0x00000801)
#define CONFIG_SYS_OR0_PRELIM		0xFFE00856
#define CONFIG_SYS_BR5_PRELIM		(CONFIG_SYS_EEPROM | 0x00000801)
#define CONFIG_SYS_OR5_PRELIM		0xFFFF03F6
#define CONFIG_SYS_BR6_PRELIM		(CONFIG_SYS_FLSIMM_BASE | 0x00001801)
#define CONFIG_SYS_OR6_PRELIM		0xFF000856
#define CONFIG_SYS_BR7_PRELIM		(CONFIG_SYS_BCSR | 0x00000801)
#define CONFIG_SYS_OR7_PRELIM		0xFFFF83F6

#define CONFIG_SYS_RESET_ADDRESS	0xC0000000

#endif /* __CONFIG_H */
Commit	Line	Data
54387ac9	1	/*
aba9f1af	2	* Copyright (C) 2003-2005 Arabella Software Ltd.
54387ac9 WD	3	* Yuli Barcohen <yuli@arabellasw.com>
	4	*
	5	* U-Boot configuration for Zephyr Engineering ZPC.1900 board.
	6	* This port was developed and tested on Revision C board.
	7	*
3765b3e7	8	* SPDX-License-Identifier: GPL-2.0+
54387ac9 WD	9	*/
	10
	11	#ifndef __CONFIG_H
	12	#define __CONFIG_H
	13
	14	#define CONFIG_MPC8260 1 /* This is an MPC8260 CPU */
	15	#define CONFIG_ZPC1900 1 /* ...on Zephyr ZPC.1900 board */
2ae18241 WD	16
	17	#define CONFIG_SYS_TEXT_BASE 0xFE000000
	18
54387ac9	19	#define CPU_ID_STR "MPC8265"
9c4c5ae3	20	#define CONFIG_CPM2 1 /* Has a CPM2 */
54387ac9	21
aba9f1af	22	/* Allow serial number (serial#) and MAC address (ethaddr) to be overwritten */
54387ac9 WD	23	#define CONFIG_ENV_OVERWRITE
	24
	25	/*
	26	* Select serial console configuration
	27	*
	28	* If either CONFIG_CONS_ON_SMC or CONFIG_CONS_ON_SCC is selected, then
	29	* CONFIG_CONS_INDEX must be set to the channel number (1-2 for SMC, 1-4
	30	* for SCC).
	31	*/
	32	#define CONFIG_CONS_ON_SMC /* Console is on SMC */
	33	#undef CONFIG_CONS_ON_SCC /* It's not on SCC */
	34	#undef CONFIG_CONS_NONE /* It's not on external UART */
	35	#define CONFIG_CONS_INDEX 1 /* SMC1 is used for console */
	36
	37	/*
	38	* Select ethernet configuration
	39	*
	40	* If either CONFIG_ETHER_ON_SCC or CONFIG_ETHER_ON_FCC is selected,
	41	* then CONFIG_ETHER_INDEX must be set to the channel number (1-4 for
	42	* SCC, 1-3 for FCC)
	43	*
	44	* If CONFIG_ETHER_NONE is defined, then either the ethernet routines
639221c7 JL	45	* must be defined elsewhere (as for the console), or CONFIG_CMD_NET
639221c7 JL	46	* must be unset.
54387ac9 WD	47	*/
	48	#undef CONFIG_ETHER_ON_SCC /* Ethernet is not on SCC */
	49	#define CONFIG_ETHER_ON_FCC /* Ethernet is on FCC */
	50	#undef CONFIG_ETHER_NONE /* No external Ethernet */
	51
	52	#ifdef CONFIG_ETHER_ON_FCC
	53
	54	#define CONFIG_ETHER_INDEX 2 /* FCC2 is used for Ethernet */
	55
	56	#if (CONFIG_ETHER_INDEX == 2)
	57	/*
	58	* - Rx clock is CLK13
	59	* - Tx clock is CLK14
	60	* - Select bus for bd/buffers (see 28-13)
	61	* - Full duplex
	62	*/
d4590da4 MF	63	# define CONFIG_SYS_CMXFCR_MASK2 (CMXFCR_FC2 \| CMXFCR_RF2CS_MSK \| CMXFCR_TF2CS_MSK)
d4590da4 MF	64	# define CONFIG_SYS_CMXFCR_VALUE2 (CMXFCR_RF2CS_CLK13 \| CMXFCR_TF2CS_CLK14)
6d0f6bcf JCPV	65	# define CONFIG_SYS_CPMFCR_RAMTYPE 0
6d0f6bcf JCPV	66	# define CONFIG_SYS_FCC_PSMR (FCC_PSMR_FDE \| FCC_PSMR_LPB)
54387ac9	67
659883c2	68	#endif /* CONFIG_ETHER_INDEX */
54387ac9 WD	69
	70	#define CONFIG_MII /* MII PHY management */
	71	#define CONFIG_BITBANGMII /* Bit-banged MDIO interface */
	72	/*
	73	* GPIO pins used for bit-banged MII communications
	74	*/
659883c2	75	#define MDIO_PORT 2 /* Port C */
be225442 LCM	76	#define MDIO_DECLARE volatile ioport_t *iop = ioport_addr ( \
	77	(immap_t *) CONFIG_SYS_IMMR, MDIO_PORT )
	78	#define MDC_DECLARE MDIO_DECLARE
	79
659883c2 WD	80	#define MDIO_ACTIVE (iop->pdir \|= 0x00400000)
	81	#define MDIO_TRISTATE (iop->pdir &= ~0x00400000)
	82	#define MDIO_READ ((iop->pdat & 0x00400000) != 0)
54387ac9	83
659883c2 WD	84	#define MDIO(bit) if(bit) iop->pdat \|= 0x00400000; \
659883c2 WD	85	else iop->pdat &= ~0x00400000
54387ac9	86
659883c2 WD	87	#define MDC(bit) if(bit) iop->pdat \|= 0x00200000; \
659883c2 WD	88	else iop->pdat &= ~0x00200000
54387ac9	89
659883c2	90	#define MIIDELAY udelay(1)
54387ac9 WD	91
	92	#endif /* CONFIG_ETHER_ON_FCC */
	93
	94	#ifndef CONFIG_8260_CLKIN
	95	#define CONFIG_8260_CLKIN 66666666 /* in Hz */
	96	#endif
	97
659883c2 WD	98	#define CONFIG_BAUDRATE 38400
659883c2 WD	99
54387ac9	100
a1aa0bb5 JL	101	/*
	102	* BOOTP options
	103	*/
	104	#define CONFIG_BOOTP_BOOTFILESIZE
	105	#define CONFIG_BOOTP_BOOTPATH
	106	#define CONFIG_BOOTP_GATEWAY
	107	#define CONFIG_BOOTP_HOSTNAME
	108
	109
a5562901 JL	110	/*
	111	* Command line configuration.
	112	*/
	113	#include <config_cmd_default.h>
	114
	115	#define CONFIG_CMD_ASKENV
	116	#define CONFIG_CMD_DHCP
	117	#define CONFIG_CMD_IMMAP
	118	#define CONFIG_CMD_MII
	119	#define CONFIG_CMD_PING
	120
54387ac9 WD	121
	122	#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
	123	#define CONFIG_BOOTCOMMAND "dhcp;bootm" /* autoboot command */
	124	#define CONFIG_BOOTARGS "root=/dev/nfs rw ip=:::::eth0:dhcp"
	125
a5562901	126	#if defined(CONFIG_CMD_KGDB)
54387ac9 WD	127	#undef CONFIG_KGDB_ON_SMC /* define if kgdb on SMC */
	128	#define CONFIG_KGDB_ON_SCC /* define if kgdb on SCC */
	129	#undef CONFIG_KGDB_NONE /* define if kgdb on something else */
	130	#define CONFIG_KGDB_INDEX 2 /* which serial channel for kgdb */
	131	#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port at */
	132	#endif
	133
	134	#define CONFIG_BZIP2 /* include support for bzip2 compressed images */
659883c2	135	#undef CONFIG_WATCHDOG /* disable platform specific watchdog */
54387ac9 WD	136
	137	/*
	138	* Miscellaneous configurable options
	139	*/
6d0f6bcf	140	#define CONFIG_SYS_HUSH_PARSER
6d0f6bcf	141	#define CONFIG_SYS_LONGHELP /* undef to save memory */
a5562901	142	#if defined(CONFIG_CMD_KGDB)
6d0f6bcf	143	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
54387ac9	144	#else
6d0f6bcf	145	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
54387ac9	146	#endif
6d0f6bcf JCPV	147	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	148	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	149	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
54387ac9	150
6d0f6bcf JCPV	151	#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
6d0f6bcf JCPV	152	#define CONFIG_SYS_MEMTEST_END 0x03800000 /* 1 ... 56 MB in DRAM */
54387ac9	153
6d0f6bcf	154	#define CONFIG_SYS_LOAD_ADDR 0x400000 /* default load address */
54387ac9	155
6d0f6bcf	156	#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
54387ac9	157
6d0f6bcf JCPV	158	#define CONFIG_SYS_SDRAM_BASE 0x00000000
6d0f6bcf JCPV	159	#define CONFIG_SYS_SDRAM_SIZE 64
aba9f1af	160
6d0f6bcf JCPV	161	#define CONFIG_SYS_IMMR 0xF0000000
	162	#define CONFIG_SYS_LSDRAM_BASE 0xFC000000
	163	#define CONFIG_SYS_FLASH_BASE 0xFE000000
	164	#define CONFIG_SYS_BCSR 0xFEA00000
	165	#define CONFIG_SYS_EEPROM 0xFEB00000
	166	#define CONFIG_SYS_FLSIMM_BASE 0xFF000000
54387ac9	167
6d0f6bcf	168	#define CONFIG_SYS_FLASH_CFI
00b1883a	169	#define CONFIG_FLASH_CFI_DRIVER
6d0f6bcf JCPV	170	#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max num of flash banks */
6d0f6bcf JCPV	171	#define CONFIG_SYS_MAX_FLASH_SECT 32 /* max num of sects on one chip */
aba9f1af	172
6d0f6bcf	173	#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLSIMM_BASE }
54387ac9 WD	174
	175	#define BCSR_PCI_MODE 0x01
	176
6d0f6bcf	177	#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
553f0982	178	#define CONFIG_SYS_INIT_RAM_SIZE 0x4000 /* Size of used area in DPRAM */
25ddd1fb	179	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
6d0f6bcf	180	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
54387ac9 WD	181
54387ac9 WD	182	/* Hard reset configuration word */
6d0f6bcf	183	#define CONFIG_SYS_HRCW_MASTER (HRCW_EBM \| HRCW_BPS01\| HRCW_CIP \|\
aba9f1af WD	184	HRCW_L2CPC10 \| HRCW_DPPC00 \| HRCW_ISB100 \|\
	185	HRCW_BMS \| HRCW_LBPC00 \| HRCW_APPC10 \|\
	186	HRCW_MODCK_H0111 \
	187	) /* 0x16848207 */
54387ac9	188	/* No slaves */
6d0f6bcf JCPV	189	#define CONFIG_SYS_HRCW_SLAVE1 0
	190	#define CONFIG_SYS_HRCW_SLAVE2 0
	191	#define CONFIG_SYS_HRCW_SLAVE3 0
	192	#define CONFIG_SYS_HRCW_SLAVE4 0
	193	#define CONFIG_SYS_HRCW_SLAVE5 0
	194	#define CONFIG_SYS_HRCW_SLAVE6 0
	195	#define CONFIG_SYS_HRCW_SLAVE7 0
54387ac9	196
14d0a02a	197	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
d98b0523	198
6d0f6bcf JCPV	199	#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
6d0f6bcf JCPV	200	#define CONFIG_SYS_RAMBOOT
54387ac9 WD	201	#endif
54387ac9 WD	202
6d0f6bcf JCPV	203	#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
	204	#define CONFIG_SYS_MALLOC_LEN (4096 << 10) /* Reserve 4 MB for malloc() */
	205	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
54387ac9	206
5a1aceb0	207	#if !defined(CONFIG_ENV_IS_IN_FLASH) && !defined(CONFIG_ENV_IS_IN_NVRAM)
9314cee6	208	#define CONFIG_ENV_IS_IN_NVRAM 1
54387ac9 WD	209	#endif
54387ac9 WD	210
5a1aceb0	211	#ifdef CONFIG_ENV_IS_IN_FLASH
0e8d1586	212	# define CONFIG_ENV_SECT_SIZE 0x10000
6d0f6bcf	213	# define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
54387ac9	214	#else
6d0f6bcf	215	# define CONFIG_ENV_ADDR (CONFIG_SYS_EEPROM + 0x400)
0e8d1586	216	# define CONFIG_ENV_SIZE 0x1000
6d0f6bcf	217	# define CONFIG_SYS_NVRAM_ACCESS_ROUTINE
54387ac9 WD	218	#endif
54387ac9 WD	219
6d0f6bcf	220	#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC8260 CPU */
a5562901	221	#if defined(CONFIG_CMD_KGDB)
6d0f6bcf	222	# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
54387ac9 WD	223	#endif
54387ac9 WD	224
6d0f6bcf JCPV	225	#define CONFIG_SYS_HID0_INIT (HID0_ICFI)
	226	#define CONFIG_SYS_HID0_FINAL (HID0_ICE \| HID0_IFEM \| HID0_ABE)
	227
	228	#define CONFIG_SYS_HID2 0
	229
	230	#define CONFIG_SYS_SIUMCR 0x42200000
	231	#define CONFIG_SYS_SYPCR 0xFFFFFFC3
	232	#define CONFIG_SYS_BCR 0x90000000
	233	#define CONFIG_SYS_SCCR SCCR_DFBRG01
	234
	235	#define CONFIG_SYS_RMR RMR_CSRE
	236	#define CONFIG_SYS_TMCNTSC (TMCNTSC_SEC\|TMCNTSC_ALR\|TMCNTSC_TCF\|TMCNTSC_TCE)
	237	#define CONFIG_SYS_PISCR (PISCR_PS\|PISCR_PTF\|PISCR_PTE)
	238	#define CONFIG_SYS_RCCR 0
	239
	240	#define CONFIG_SYS_PSDMR /* 0x834DA43B */0x014DA43A
	241	#define CONFIG_SYS_PSRT 0x0F/* 0x0C */
	242	#define CONFIG_SYS_LSDMR 0x0085A562
	243	#define CONFIG_SYS_LSRT 0x0F
	244	#define CONFIG_SYS_MPTPR 0x4000
	245
	246	#define CONFIG_SYS_PSDRAM_BR (CONFIG_SYS_SDRAM_BASE \| 0x00000041)
	247	#define CONFIG_SYS_PSDRAM_OR 0xFC0028C0
	248	#define CONFIG_SYS_LSDRAM_BR (CONFIG_SYS_LSDRAM_BASE \| 0x00001861)
	249	#define CONFIG_SYS_LSDRAM_OR 0xFF803480
	250
	251	#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE \| 0x00000801)
	252	#define CONFIG_SYS_OR0_PRELIM 0xFFE00856
	253	#define CONFIG_SYS_BR5_PRELIM (CONFIG_SYS_EEPROM \| 0x00000801)
	254	#define CONFIG_SYS_OR5_PRELIM 0xFFFF03F6
	255	#define CONFIG_SYS_BR6_PRELIM (CONFIG_SYS_FLSIMM_BASE \| 0x00001801)
	256	#define CONFIG_SYS_OR6_PRELIM 0xFF000856
	257	#define CONFIG_SYS_BR7_PRELIM (CONFIG_SYS_BCSR \| 0x00000801)
	258	#define CONFIG_SYS_OR7_PRELIM 0xFFFF83F6
	259
	260	#define CONFIG_SYS_RESET_ADDRESS 0xC0000000
54387ac9 WD	261
54387ac9 WD	262	#endif /* __CONFIG_H */