[people/ms/u-boot.git] / include / configs / blackstamp.h

/*
 * U-boot - Configuration file for BlackStamp board
 * Configuration by Ben Matthews for UR LLE using bf533-stamp.h
 * as a template
 * See http://blackfin.uclinux.org/gf/project/blackstamp/
 */

#ifndef __CONFIG_BLACKSTAMP_H__
#define __CONFIG_BLACKSTAMP_H__

#include <asm/config-pre.h>

/*
 * Debugging: Set these options if you're having problems
 */
/*
 * #define CONFIG_DEBUG_EARLY_SERIAL
 * #define DEBUG
 * #define CONFIG_DEBUG_DUMP
 * #define CONFIG_DEBUG_DUMP_SYMS
*/
#define CONFIG_PANIC_HANG 0

/* CPU Options
 * Be sure to set the Silicon Revision Correctly
 */
#define CONFIG_BFIN_CPU		bf532-0.5
#define CONFIG_BFIN_BOOT_MODE	BFIN_BOOT_SPI_MASTER

/*
 * Board settings
 */
#define CONFIG_SMC91111	1
#define CONFIG_SMC91111_BASE	0x20300300

/* FLASH/ETHERNET uses the same address range
 * Depending on what you have the CPLD doing
 * this probably isn't needed
 */
#define SHARED_RESOURCES	1

/* Is I2C bit-banged? */
#undef CONFIG_SOFT_I2

/*
 * Clock Settings
 *	CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
 *	SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
 */
/* CONFIG_CLKIN_HZ is any value in Hz					*/
#define CONFIG_CLKIN_HZ			25000000
/* CLKIN_HALF controls the DF bit in PLL_CTL      0 = CLKIN		*/
/*                                                1 = CLKIN / 2		*/
#define CONFIG_CLKIN_HALF		0
/* PLL_BYPASS controls the BYPASS bit in PLL_CTL  0 = do not bypass	*/
/*                                                1 = bypass PLL	*/
#define CONFIG_PLL_BYPASS		0
/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL		*/
/* Values can range from 0-63 (where 0 means 64)			*/
#define CONFIG_VCO_MULT			16
/* CCLK_DIV controls the core clock divider				*/
/* Values can be 1, 2, 4, or 8 ONLY					*/
#define CONFIG_CCLK_DIV			1
/* SCLK_DIV controls the system clock divider				*/
/* Values can range from 1-15						*/
#define CONFIG_SCLK_DIV			3

/*
 * Network settings
 */

#ifdef CONFIG_SMC91111
#define CONFIG_IPADDR		192.168.0.15
#define CONFIG_NETMASK		255.255.255.0
#define CONFIG_GATEWAYIP	192.168.0.1
#define CONFIG_SERVERIP		192.168.0.2
#define CONFIG_HOSTNAME		blackstamp
#define CONFIG_ROOTPATH		"/checkout/uClinux-dist/romfs"
#define CONFIG_SYS_AUTOLOAD		"no"

/* To remove hardcoding and enable MAC storage in EEPROM  */
/* #define CONFIG_ETHADDR		02:80:ad:20:31:b8 */
#endif

#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_OFFSET	0x40000
#define CONFIG_ENV_SIZE		0x2000
#define CONFIG_ENV_SECT_SIZE	0x40000

/*
 * SDRAM settings & memory map
 */

#define CONFIG_MEM_SIZE		64	/* 128, 64, 32, 16 */
#define CONFIG_MEM_ADD_WDTH	10	/* 8, 9, 10, 11    */

#define CONFIG_SYS_MONITOR_LEN	(256 << 10)
#define CONFIG_SYS_MALLOC_LEN	(384 << 10)

/*
 * Command settings
 */

#define CONFIG_SYS_LONGHELP		1
#define CONFIG_CMDLINE_EDITING	1
#define CONFIG_AUTO_COMPLETE	1
#define CONFIG_ENV_OVERWRITE	1

#include <config_cmd_default.h>

#ifdef CONFIG_SMC91111
# define CONFIG_CMD_DHCP
# define CONFIG_CMD_PING
#else
# undef CONFIG_CMD_NET
#endif

#ifdef CONFIG_SOFT_I2C
# define CONFIG_CMD_I2C
#endif

#define CONFIG_CMD_BOOTLDR
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_CPLBINFO
#define CONFIG_CMD_DATE
#define CONFIG_CMD_SF
#define CONFIG_CMD_ELF

#define CONFIG_BOOTDELAY     5
#define CONFIG_BOOTCOMMAND   "run ramboot"
#define CONFIG_BOOTARGS \
	"root=/dev/mtdblock0 rw " \
	"clkin_hz=" __stringify(CONFIG_CLKIN_HZ) " " \
	"earlyprintk=" \
		"serial," \
		"uart" __stringify(CONFIG_UART_CONSOLE) "," \
		__stringify(CONFIG_BAUDRATE) " " \
	"console=ttyBF0," __stringify(CONFIG_BAUDRATE)

#if defined(CONFIG_CMD_NET)
# if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
#  define UBOOT_ENV_FILE "u-boot.bin"
# else
#  define UBOOT_ENV_FILE "u-boot.ldr"
# endif
# if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
#  ifdef CONFIG_SPI
#   define UBOOT_ENV_UPDATE \
		"eeprom write $(loadaddr) 0x0 $(filesize)"
#  else
#   define UBOOT_ENV_UPDATE \
		"sf probe " __stringify(BFIN_BOOT_SPI_SSEL) ";" \
		"sf erase 0 0x40000;" \
		"sf write $(loadaddr) 0 $(filesize)"
#  endif
# else
#  define UBOOT_ENV_UPDATE \
		"protect off 0x20000000 0x2003FFFF;" \
		"erase 0x20000000 0x2003FFFF;" \
		"cp.b $(loadaddr) 0x20000000 $(filesize)"
# endif
# define NETWORK_ENV_SETTINGS \
	"ubootfile=" UBOOT_ENV_FILE "\0" \
	"update=" \
		"tftp $(loadaddr) $(ubootfile);" \
		UBOOT_ENV_UPDATE \
		"\0" \
	"addip=set bootargs $(bootargs) " \
		"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):" \
		   "$(hostname):eth0:off" \
		"\0" \
	"ramargs=set bootargs " CONFIG_BOOTARGS "\0" \
	"ramboot=" \
		"tftp $(loadaddr) uImage;" \
		"run ramargs;" \
		"run addip;" \
		"bootm" \
		"\0" \
	"nfsargs=set bootargs " \
		"root=/dev/nfs rw " \
		"nfsroot=$(serverip):$(rootpath),tcp,nfsvers=3" \
		"\0" \
	"nfsboot=" \
		"tftp $(loadaddr) vmImage;" \
		"run nfsargs;" \
		"run addip;" \
		"bootm" \
		"\0"
#else
# define NETWORK_ENV_SETTINGS
#endif

/*
 * Console settings
 */
#define CONFIG_BAUDRATE		57600
#define CONFIG_LOADS_ECHO	1
#define CONFIG_UART_CONSOLE	0

/*
 * I2C settings
 * By default PF2 is used as SDA and PF3 as SCL on the Stamp board
 * Located on the expansion connector on pins 86/85
 * Note these pins are arbitrarily chosen because we aren't using
 * them yet. You can (and probably should) change these values!
 */
#ifdef CONFIG_SOFT_I2C
#define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF9
#define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF8
#define CONFIG_SYS_I2C_SPEED		50000
#define CONFIG_SYS_I2C_SLAVE		0xFE
#endif

/*
 * Miscellaneous configurable options
 */
#define CONFIG_RTC_BFIN		1

/*
 * Serial Flash Infomation
 */
#define CONFIG_BFIN_SPI
/* For the M25P64 SCK Should be Kept < 15Mhz */
#define CONFIG_ENV_SPI_MAX_HZ	15000000
#define CONFIG_SF_DEFAULT_SPEED	15000000
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_STMICRO

/*
 * FLASH organization and environment definitions
 */

#define CONFIG_EBIU_AMGCTL_VAL		0xFF
#define CONFIG_EBIU_AMBCTL0_VAL		0xBBC3BBC3
#define CONFIG_EBIU_AMBCTL1_VAL		0x99B39983
#define CONFIG_EBIU_SDRRC_VAL		0x268
#define CONFIG_EBIU_SDGCTL_VAL		0x911109

/* Even though Rev C boards have Parallel Flash
 * We aren't supporting it. Newer versions of the
 * hardware don't support Parallel Flash at all.
 */
#define CONFIG_SYS_NO_FLASH
#undef CONFIG_CMD_IMLS
#undef CONFIG_CMD_JFFS2
#undef CONFIG_CMD_FLASH

#endif
Commit	Line	Data
3088189a MF	1	/*
	2	* U-boot - Configuration file for BlackStamp board
	3	* Configuration by Ben Matthews for UR LLE using bf533-stamp.h
	4	* as a template
	5	* See http://blackfin.uclinux.org/gf/project/blackstamp/
	6	*/
	7
	8	#ifndef __CONFIG_BLACKSTAMP_H__
	9	#define __CONFIG_BLACKSTAMP_H__
	10
f348ab85	11	#include <asm/config-pre.h>
3088189a MF	12
	13	/*
	14	* Debugging: Set these options if you're having problems
	15	*/
	16	/*
	17	* #define CONFIG_DEBUG_EARLY_SERIAL
	18	* #define DEBUG
	19	* #define CONFIG_DEBUG_DUMP
	20	* #define CONFIG_DEBUG_DUMP_SYMS
	21	*/
	22	#define CONFIG_PANIC_HANG 0
	23
	24	/* CPU Options
	25	* Be sure to set the Silicon Revision Correctly
	26	*/
fbcf8e8c	27	#define CONFIG_BFIN_CPU bf532-0.5
3088189a MF	28	#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_SPI_MASTER
	29
	30	/*
	31	* Board settings
	32	*/
7194ab80	33	#define CONFIG_SMC91111 1
3088189a MF	34	#define CONFIG_SMC91111_BASE 0x20300300
	35
	36	/* FLASH/ETHERNET uses the same address range
	37	* Depending on what you have the CPLD doing
	38	* this probably isn't needed
	39	*/
	40	#define SHARED_RESOURCES 1
	41
	42	/* Is I2C bit-banged? */
	43	#undef CONFIG_SOFT_I2
	44
	45	/*
	46	* Clock Settings
	47	* CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
	48	* SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
	49	*/
	50	/* CONFIG_CLKIN_HZ is any value in Hz */
	51	#define CONFIG_CLKIN_HZ 25000000
	52	/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
	53	/* 1 = CLKIN / 2 */
	54	#define CONFIG_CLKIN_HALF 0
	55	/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
	56	/* 1 = bypass PLL */
	57	#define CONFIG_PLL_BYPASS 0
	58	/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
	59	/* Values can range from 0-63 (where 0 means 64) */
	60	#define CONFIG_VCO_MULT 16
	61	/* CCLK_DIV controls the core clock divider */
	62	/* Values can be 1, 2, 4, or 8 ONLY */
	63	#define CONFIG_CCLK_DIV 1
	64	/* SCLK_DIV controls the system clock divider */
	65	/* Values can range from 1-15 */
	66	#define CONFIG_SCLK_DIV 3
	67
	68	/*
	69	* Network settings
	70	*/
	71
7194ab80	72	#ifdef CONFIG_SMC91111
3088189a MF	73	#define CONFIG_IPADDR 192.168.0.15
	74	#define CONFIG_NETMASK 255.255.255.0
	75	#define CONFIG_GATEWAYIP 192.168.0.1
	76	#define CONFIG_SERVERIP 192.168.0.2
	77	#define CONFIG_HOSTNAME blackstamp
8b3637c6	78	#define CONFIG_ROOTPATH "/checkout/uClinux-dist/romfs"
3088189a MF	79	#define CONFIG_SYS_AUTOLOAD "no"
	80
	81	/* To remove hardcoding and enable MAC storage in EEPROM */
	82	/* #define CONFIG_ETHADDR 02:80:ad:20:31:b8 */
	83	#endif
	84
	85	#define CONFIG_ENV_IS_IN_SPI_FLASH
f8bf54b4	86	#define CONFIG_ENV_OFFSET 0x40000
3088189a MF	87	#define CONFIG_ENV_SIZE 0x2000
3088189a MF	88	#define CONFIG_ENV_SECT_SIZE 0x40000
3088189a MF	89
	90	/*
	91	* SDRAM settings & memory map
	92	*/
	93
	94	#define CONFIG_MEM_SIZE 64 /* 128, 64, 32, 16 */
	95	#define CONFIG_MEM_ADD_WDTH 10 /* 8, 9, 10, 11 */
	96
	97	#define CONFIG_SYS_MONITOR_LEN (256 << 10)
	98	#define CONFIG_SYS_MALLOC_LEN (384 << 10)
	99
	100	/*
	101	* Command settings
	102	*/
	103
	104	#define CONFIG_SYS_LONGHELP 1
	105	#define CONFIG_CMDLINE_EDITING 1
	106	#define CONFIG_AUTO_COMPLETE 1
	107	#define CONFIG_ENV_OVERWRITE 1
	108
	109	#include <config_cmd_default.h>
	110
7194ab80	111	#ifdef CONFIG_SMC91111
3088189a MF	112	# define CONFIG_CMD_DHCP
	113	# define CONFIG_CMD_PING
	114	#else
	115	# undef CONFIG_CMD_NET
	116	#endif
	117
	118	#ifdef CONFIG_SOFT_I2C
	119	# define CONFIG_CMD_I2C
	120	#endif
	121
	122	#define CONFIG_CMD_BOOTLDR
	123	#define CONFIG_CMD_CACHE
	124	#define CONFIG_CMD_CPLBINFO
	125	#define CONFIG_CMD_DATE
	126	#define CONFIG_CMD_SF
	127	#define CONFIG_CMD_ELF
	128
	129	#define CONFIG_BOOTDELAY 5
	130	#define CONFIG_BOOTCOMMAND "run ramboot"
	131	#define CONFIG_BOOTARGS \
	132	"root=/dev/mtdblock0 rw " \
5368c55d	133	"clkin_hz=" __stringify(CONFIG_CLKIN_HZ) " " \
3088189a MF	134	"earlyprintk=" \
3088189a MF	135	"serial," \
5368c55d MV	136	"uart" __stringify(CONFIG_UART_CONSOLE) "," \
	137	__stringify(CONFIG_BAUDRATE) " " \
	138	"console=ttyBF0," __stringify(CONFIG_BAUDRATE)
3088189a MF	139
	140	#if defined(CONFIG_CMD_NET)
	141	# if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_BYPASS)
	142	# define UBOOT_ENV_FILE "u-boot.bin"
	143	# else
	144	# define UBOOT_ENV_FILE "u-boot.ldr"
	145	# endif
	146	# if (CONFIG_BFIN_BOOT_MODE == BFIN_BOOT_SPI_MASTER)
	147	# ifdef CONFIG_SPI
	148	# define UBOOT_ENV_UPDATE \
	149	"eeprom write $(loadaddr) 0x0 $(filesize)"
	150	# else
	151	# define UBOOT_ENV_UPDATE \
5368c55d	152	"sf probe " __stringify(BFIN_BOOT_SPI_SSEL) ";" \
3088189a MF	153	"sf erase 0 0x40000;" \
	154	"sf write $(loadaddr) 0 $(filesize)"
	155	# endif
	156	# else
	157	# define UBOOT_ENV_UPDATE \
	158	"protect off 0x20000000 0x2003FFFF;" \
	159	"erase 0x20000000 0x2003FFFF;" \
	160	"cp.b $(loadaddr) 0x20000000 $(filesize)"
	161	# endif
	162	# define NETWORK_ENV_SETTINGS \
	163	"ubootfile=" UBOOT_ENV_FILE "\0" \
	164	"update=" \
	165	"tftp $(loadaddr) $(ubootfile);" \
	166	UBOOT_ENV_UPDATE \
	167	"\0" \
	168	"addip=set bootargs $(bootargs) " \
	169	"ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):" \
	170	"$(hostname):eth0:off" \
	171	"\0" \
	172	"ramargs=set bootargs " CONFIG_BOOTARGS "\0" \
	173	"ramboot=" \
	174	"tftp $(loadaddr) uImage;" \
	175	"run ramargs;" \
	176	"run addip;" \
	177	"bootm" \
	178	"\0" \
	179	"nfsargs=set bootargs " \
	180	"root=/dev/nfs rw " \
	181	"nfsroot=$(serverip):$(rootpath),tcp,nfsvers=3" \
	182	"\0" \
	183	"nfsboot=" \
	184	"tftp $(loadaddr) vmImage;" \
	185	"run nfsargs;" \
	186	"run addip;" \
	187	"bootm" \
	188	"\0"
	189	#else
	190	# define NETWORK_ENV_SETTINGS
	191	#endif
	192
	193	/*
	194	* Console settings
	195	*/
	196	#define CONFIG_BAUDRATE 57600
	197	#define CONFIG_LOADS_ECHO 1
	198	#define CONFIG_UART_CONSOLE 0
	199
	200	/*
	201	* I2C settings
	202	* By default PF2 is used as SDA and PF3 as SCL on the Stamp board
	203	* Located on the expansion connector on pins 86/85
	204	* Note these pins are arbitrarily chosen because we aren't using
	205	* them yet. You can (and probably should) change these values!
	206	*/
	207	#ifdef CONFIG_SOFT_I2C
beb60e77 MF	208	#define CONFIG_SOFT_I2C_GPIO_SCL GPIO_PF9
beb60e77 MF	209	#define CONFIG_SOFT_I2C_GPIO_SDA GPIO_PF8
3088189a MF	210	#define CONFIG_SYS_I2C_SPEED 50000
	211	#define CONFIG_SYS_I2C_SLAVE 0xFE
	212	#endif
	213
	214	/*
	215	* Miscellaneous configurable options
	216	*/
	217	#define CONFIG_RTC_BFIN 1
	218
	219	/*
	220	* Serial Flash Infomation
	221	*/
	222	#define CONFIG_BFIN_SPI
f8bf54b4 MF	223	/* For the M25P64 SCK Should be Kept < 15Mhz */
	224	#define CONFIG_ENV_SPI_MAX_HZ 15000000
	225	#define CONFIG_SF_DEFAULT_SPEED 15000000
3088189a MF	226	#define CONFIG_SPI_FLASH
	227	#define CONFIG_SPI_FLASH_STMICRO
	228
	229	/*
	230	* FLASH organization and environment definitions
	231	*/
	232
	233	#define CONFIG_EBIU_AMGCTL_VAL 0xFF
	234	#define CONFIG_EBIU_AMBCTL0_VAL 0xBBC3BBC3
	235	#define CONFIG_EBIU_AMBCTL1_VAL 0x99B39983
	236	#define CONFIG_EBIU_SDRRC_VAL 0x268
	237	#define CONFIG_EBIU_SDGCTL_VAL 0x911109
	238
	239	/* Even though Rev C boards have Parallel Flash
	240	* We aren't supporting it. Newer versions of the
	241	* hardware don't support Parallel Flash at all.
	242	*/
	243	#define CONFIG_SYS_NO_FLASH
	244	#undef CONFIG_CMD_IMLS
	245	#undef CONFIG_CMD_JFFS2
	246	#undef CONFIG_CMD_FLASH
	247
3088189a	248	#endif