]>
Commit | Line | Data |
---|---|---|
a562e1bd WD |
1 | /* |
2 | * Configuation settings for the Sentec Cobra Board. | |
3 | * | |
4 | * (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de> | |
5 | * | |
3765b3e7 | 6 | * SPDX-License-Identifier: GPL-2.0+ |
a562e1bd WD |
7 | */ |
8 | ||
9 | /* --- | |
10 | * Version: U-boot 1.0.0 - initial release for Sentec COBRA5272 board | |
11 | * Date: 2004-03-29 | |
12 | * Author: Florian Schlote | |
13 | * | |
14 | * For a description of configuration options please refer also to the | |
15 | * general u-boot-1.x.x/README file | |
16 | * --- | |
17 | */ | |
18 | ||
19 | /* --- | |
20 | * board/config.h - configuration options, board specific | |
21 | * --- | |
22 | */ | |
23 | ||
24 | #ifndef _CONFIG_COBRA5272_H | |
25 | #define _CONFIG_COBRA5272_H | |
26 | ||
a562e1bd WD |
27 | /* --- |
28 | * Defines processor clock - important for correct timings concerning serial | |
29 | * interface etc. | |
a562e1bd WD |
30 | * --- |
31 | */ | |
32 | ||
6d0f6bcf JCPV |
33 | #define CONFIG_SYS_CLK 66000000 |
34 | #define CONFIG_SYS_SDRAM_SIZE 16 /* SDRAM size in MB */ | |
a562e1bd WD |
35 | |
36 | /* --- | |
37 | * Enable use of Ethernet | |
38 | * --- | |
39 | */ | |
6706424d | 40 | #define CONFIG_MCFFEC |
a562e1bd | 41 | |
6706424d TL |
42 | /* Enable Dma Timer */ |
43 | #define CONFIG_MCFTMR | |
a562e1bd WD |
44 | |
45 | /* --- | |
46 | * Define baudrate for UART1 (console output, tftp, ...) | |
47 | * default value of CONFIG_BAUDRATE for Sentec board: 19200 baud | |
6d0f6bcf | 48 | * CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected in u-boot command |
a562e1bd WD |
49 | * interface |
50 | * --- | |
51 | */ | |
52 | ||
6706424d | 53 | #define CONFIG_MCFUART |
6d0f6bcf | 54 | #define CONFIG_SYS_UART_PORT (0) |
a562e1bd | 55 | #define CONFIG_BAUDRATE 19200 |
a562e1bd WD |
56 | |
57 | /* --- | |
58 | * set "#if 0" to "#if 1" if (Hardware)-WATCHDOG should be enabled & change | |
59 | * timeout acc. to your needs | |
60 | * #define CONFIG_WATCHDOG_TIMEOUT x , x is timeout in milliseconds, e. g. 10000 | |
61 | * for 10 sec | |
62 | * --- | |
63 | */ | |
64 | ||
65 | #if 0 | |
66 | #define CONFIG_WATCHDOG | |
67 | #define CONFIG_WATCHDOG_TIMEOUT 10000 /* timeout in milliseconds */ | |
68 | #endif | |
69 | ||
70 | /* --- | |
71 | * CONFIG_MONITOR_IS_IN_RAM defines if u-boot is started from a different | |
72 | * bootloader residing in flash ('chainloading'); if you want to use | |
73 | * chainloading or want to compile a u-boot binary that can be loaded into | |
74 | * RAM via BDM set | |
53677ef1 | 75 | * "#if 0" to "#if 1" |
a562e1bd WD |
76 | * You will need a first stage bootloader then, e. g. colilo or a working BDM |
77 | * cable (Background Debug Mode) | |
78 | * | |
79 | * Setting #if 0: u-boot will start from flash and relocate itself to RAM | |
80 | * | |
14d0a02a | 81 | * Please do not forget to modify the setting of CONFIG_SYS_TEXT_BASE |
a562e1bd WD |
82 | * in board/cobra5272/config.mk accordingly (#if 0: 0xffe00000; #if 1: 0x20000) |
83 | * | |
84 | * --- | |
85 | */ | |
86 | ||
87 | #if 0 | |
88 | #define CONFIG_MONITOR_IS_IN_RAM /* monitor is started from a preloader */ | |
89 | #endif | |
90 | ||
91 | /* --- | |
92 | * Configuration for environment | |
93 | * Environment is embedded in u-boot in the second sector of the flash | |
94 | * --- | |
95 | */ | |
96 | ||
97 | #ifndef CONFIG_MONITOR_IS_IN_RAM | |
0e8d1586 JCPV |
98 | #define CONFIG_ENV_OFFSET 0x4000 |
99 | #define CONFIG_ENV_SECT_SIZE 0x2000 | |
5a1aceb0 | 100 | #define CONFIG_ENV_IS_IN_FLASH 1 |
a562e1bd | 101 | #else |
0e8d1586 JCPV |
102 | #define CONFIG_ENV_ADDR 0xffe04000 |
103 | #define CONFIG_ENV_SECT_SIZE 0x2000 | |
5a1aceb0 | 104 | #define CONFIG_ENV_IS_IN_FLASH 1 |
a562e1bd WD |
105 | #endif |
106 | ||
5296cb1d | 107 | #define LDS_BOARD_TEXT \ |
108 | . = DEFINED(env_offset) ? env_offset : .; \ | |
109 | common/env_embedded.o (.text); | |
37e4f24b | 110 | |
80ff4f99 JL |
111 | /* |
112 | * BOOTP options | |
113 | */ | |
114 | #define CONFIG_BOOTP_BOOTFILESIZE | |
115 | #define CONFIG_BOOTP_BOOTPATH | |
116 | #define CONFIG_BOOTP_GATEWAY | |
117 | #define CONFIG_BOOTP_HOSTNAME | |
118 | ||
119 | ||
37e4f24b JL |
120 | /* |
121 | * Command line configuration. | |
a562e1bd | 122 | */ |
37e4f24b JL |
123 | #include <config_cmd_default.h> |
124 | ||
125 | #define CONFIG_CMD_PING | |
a562e1bd | 126 | |
37e4f24b JL |
127 | #undef CONFIG_CMD_LOADS |
128 | #undef CONFIG_CMD_LOADB | |
129 | #undef CONFIG_CMD_MII | |
a562e1bd | 130 | |
6706424d | 131 | #ifdef CONFIG_MCFFEC |
6706424d | 132 | # define CONFIG_MII 1 |
0f3ba7e9 | 133 | # define CONFIG_MII_INIT 1 |
6d0f6bcf JCPV |
134 | # define CONFIG_SYS_DISCOVER_PHY |
135 | # define CONFIG_SYS_RX_ETH_BUFFER 8 | |
136 | # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN | |
6706424d | 137 | |
6d0f6bcf JCPV |
138 | # define CONFIG_SYS_FEC0_PINMUX 0 |
139 | # define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE | |
53677ef1 | 140 | # define MCFFEC_TOUT_LOOP 50000 |
6d0f6bcf JCPV |
141 | /* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */ |
142 | # ifndef CONFIG_SYS_DISCOVER_PHY | |
6706424d TL |
143 | # define FECDUPLEX FULL |
144 | # define FECSPEED _100BASET | |
145 | # else | |
6d0f6bcf JCPV |
146 | # ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN |
147 | # define CONFIG_SYS_FAULT_ECHO_LINK_DOWN | |
6706424d | 148 | # endif |
6d0f6bcf | 149 | # endif /* CONFIG_SYS_DISCOVER_PHY */ |
6706424d | 150 | #endif |
a562e1bd WD |
151 | |
152 | /* | |
153 | *----------------------------------------------------------------------------- | |
154 | * Define user parameters that have to be customized most likely | |
155 | *----------------------------------------------------------------------------- | |
156 | */ | |
157 | ||
158 | /*AUTOBOOT settings - booting images automatically by u-boot after power on*/ | |
159 | ||
160 | #define CONFIG_BOOTDELAY 5 /* used for autoboot, delay in | |
161 | seconds u-boot will wait before starting defined (auto-)boot command, setting | |
162 | to -1 disables delay, setting to 0 will too prevent access to u-boot command | |
163 | interface: u-boot then has to reflashed */ | |
164 | ||
165 | ||
166 | /* The following settings will be contained in the environment block ; if you | |
167 | want to use a neutral environment all those settings can be manually set in | |
168 | u-boot: 'set' command */ | |
169 | ||
170 | #if 0 | |
171 | ||
172 | #define CONFIG_BOOTCOMMAND "bootm 0xffe80000" /*Autoboto command, please | |
173 | enter a valid image address in flash */ | |
174 | ||
175 | #define CONFIG_BOOTARGS " " /* default bootargs that are | |
176 | considered during boot */ | |
177 | ||
178 | /* User network settings */ | |
179 | ||
180 | #define CONFIG_ETHADDR 00:00:00:00:00:09 /* default ethernet MAC addr. */ | |
181 | #define CONFIG_IPADDR 192.168.100.2 /* default board IP address */ | |
182 | #define CONFIG_SERVERIP 192.168.100.1 /* default tftp server IP address */ | |
183 | ||
184 | #endif | |
185 | ||
6d0f6bcf | 186 | #define CONFIG_SYS_PROMPT "COBRA > " /* Layout of u-boot prompt*/ |
a562e1bd | 187 | |
6d0f6bcf | 188 | #define CONFIG_SYS_LOAD_ADDR 0x20000 /*Defines default RAM address |
a562e1bd WD |
189 | from which user programs will be started */ |
190 | ||
191 | /*---*/ | |
192 | ||
6d0f6bcf | 193 | #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
a562e1bd | 194 | |
37e4f24b | 195 | #if defined(CONFIG_CMD_KGDB) |
6d0f6bcf | 196 | #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ |
a562e1bd | 197 | #else |
6d0f6bcf | 198 | #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ |
a562e1bd | 199 | #endif |
6d0f6bcf JCPV |
200 | #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */ |
201 | #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ | |
202 | #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ | |
a562e1bd WD |
203 | |
204 | /* | |
205 | *----------------------------------------------------------------------------- | |
206 | * End of user parameters to be customized | |
207 | *----------------------------------------------------------------------------- | |
208 | */ | |
209 | ||
210 | /* --- | |
211 | * Defines memory range for test | |
212 | * --- | |
213 | */ | |
214 | ||
6d0f6bcf JCPV |
215 | #define CONFIG_SYS_MEMTEST_START 0x400 |
216 | #define CONFIG_SYS_MEMTEST_END 0x380000 | |
a562e1bd WD |
217 | |
218 | /* --- | |
219 | * Low Level Configuration Settings | |
220 | * (address mappings, register initial values, etc.) | |
221 | * You should know what you are doing if you make changes here. | |
222 | * --- | |
223 | */ | |
224 | ||
225 | /* --- | |
226 | * Base register address | |
227 | * --- | |
228 | */ | |
229 | ||
6d0f6bcf | 230 | #define CONFIG_SYS_MBAR 0x10000000 /* Register Base Addrs */ |
a562e1bd WD |
231 | |
232 | /* --- | |
233 | * System Conf. Reg. & System Protection Reg. | |
234 | * --- | |
235 | */ | |
236 | ||
6d0f6bcf JCPV |
237 | #define CONFIG_SYS_SCR 0x0003 |
238 | #define CONFIG_SYS_SPR 0xffff | |
a562e1bd WD |
239 | |
240 | /* --- | |
241 | * Ethernet settings | |
242 | * --- | |
243 | */ | |
244 | ||
6d0f6bcf JCPV |
245 | #define CONFIG_SYS_DISCOVER_PHY |
246 | #define CONFIG_SYS_ENET_BD_BASE 0x780000 | |
a562e1bd WD |
247 | |
248 | /*----------------------------------------------------------------------- | |
249 | * Definitions for initial stack pointer and data area (in internal SRAM) | |
250 | */ | |
6d0f6bcf | 251 | #define CONFIG_SYS_INIT_RAM_ADDR 0x20000000 |
553f0982 | 252 | #define CONFIG_SYS_INIT_RAM_SIZE 0x1000 /* Size of used area in internal SRAM */ |
25ddd1fb | 253 | #define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) |
6d0f6bcf | 254 | #define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET |
a562e1bd WD |
255 | |
256 | /*----------------------------------------------------------------------- | |
257 | * Start addresses for the final memory configuration | |
258 | * (Set up by the startup code) | |
6d0f6bcf | 259 | * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0 |
a562e1bd | 260 | */ |
6d0f6bcf | 261 | #define CONFIG_SYS_SDRAM_BASE 0x00000000 |
a562e1bd WD |
262 | |
263 | /* | |
264 | *------------------------------------------------------------------------- | |
265 | * RAM SIZE (is defined above) | |
266 | *----------------------------------------------------------------------- | |
267 | */ | |
268 | ||
6d0f6bcf | 269 | /* #define CONFIG_SYS_SDRAM_SIZE 16 */ |
a562e1bd WD |
270 | |
271 | /* | |
272 | *----------------------------------------------------------------------- | |
273 | */ | |
274 | ||
6d0f6bcf | 275 | #define CONFIG_SYS_FLASH_BASE 0xffe00000 |
a562e1bd WD |
276 | |
277 | #ifdef CONFIG_MONITOR_IS_IN_RAM | |
6d0f6bcf | 278 | #define CONFIG_SYS_MONITOR_BASE 0x20000 |
a562e1bd | 279 | #else |
6d0f6bcf | 280 | #define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400) |
a562e1bd WD |
281 | #endif |
282 | ||
6d0f6bcf JCPV |
283 | #define CONFIG_SYS_MONITOR_LEN 0x20000 |
284 | #define CONFIG_SYS_MALLOC_LEN (256 << 10) | |
285 | #define CONFIG_SYS_BOOTPARAMS_LEN 64*1024 | |
a562e1bd WD |
286 | |
287 | /* | |
288 | * For booting Linux, the board info and command line data | |
289 | * have to be in the first 8 MB of memory, since this is | |
290 | * the maximum mapped by the Linux kernel during initialization ?? | |
291 | */ | |
6d0f6bcf | 292 | #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ |
a562e1bd WD |
293 | |
294 | /*----------------------------------------------------------------------- | |
295 | * FLASH organization | |
296 | */ | |
6d0f6bcf JCPV |
297 | #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
298 | #define CONFIG_SYS_MAX_FLASH_SECT 11 /* max number of sectors on one chip */ | |
299 | #define CONFIG_SYS_FLASH_ERASE_TOUT 1000 /* flash timeout */ | |
a562e1bd WD |
300 | |
301 | /*----------------------------------------------------------------------- | |
302 | * Cache Configuration | |
303 | */ | |
6d0f6bcf | 304 | #define CONFIG_SYS_CACHELINE_SIZE 16 |
a562e1bd | 305 | |
dd9f054e | 306 | #define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ |
553f0982 | 307 | CONFIG_SYS_INIT_RAM_SIZE - 8) |
dd9f054e | 308 | #define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \ |
553f0982 | 309 | CONFIG_SYS_INIT_RAM_SIZE - 4) |
dd9f054e TL |
310 | #define CONFIG_SYS_ICACHE_INV (CF_CACR_CINV | CF_CACR_INVI) |
311 | #define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \ | |
312 | CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \ | |
313 | CF_ACR_EN | CF_ACR_SM_ALL) | |
314 | #define CONFIG_SYS_CACHE_ICACR (CF_CACR_CENB | CF_CACR_CINV | \ | |
315 | CF_CACR_DISD | CF_CACR_INVI | \ | |
316 | CF_CACR_CEIB | CF_CACR_DCM | \ | |
317 | CF_CACR_EUSP) | |
318 | ||
a562e1bd WD |
319 | /*----------------------------------------------------------------------- |
320 | * Memory bank definitions | |
321 | * | |
322 | * Please refer also to Motorola Coldfire user manual - Chapter XXX | |
323 | * <http://e-www.motorola.com/files/dsp/doc/ref_manual/MCF5272UM.pdf> | |
324 | */ | |
6d0f6bcf JCPV |
325 | #define CONFIG_SYS_BR0_PRELIM 0xFFE00201 |
326 | #define CONFIG_SYS_OR0_PRELIM 0xFFE00014 | |
a562e1bd | 327 | |
6d0f6bcf JCPV |
328 | #define CONFIG_SYS_BR1_PRELIM 0 |
329 | #define CONFIG_SYS_OR1_PRELIM 0 | |
a562e1bd | 330 | |
6d0f6bcf JCPV |
331 | #define CONFIG_SYS_BR2_PRELIM 0 |
332 | #define CONFIG_SYS_OR2_PRELIM 0 | |
a562e1bd | 333 | |
6d0f6bcf JCPV |
334 | #define CONFIG_SYS_BR3_PRELIM 0 |
335 | #define CONFIG_SYS_OR3_PRELIM 0 | |
a562e1bd | 336 | |
6d0f6bcf JCPV |
337 | #define CONFIG_SYS_BR4_PRELIM 0 |
338 | #define CONFIG_SYS_OR4_PRELIM 0 | |
a562e1bd | 339 | |
6d0f6bcf JCPV |
340 | #define CONFIG_SYS_BR5_PRELIM 0 |
341 | #define CONFIG_SYS_OR5_PRELIM 0 | |
a562e1bd | 342 | |
6d0f6bcf JCPV |
343 | #define CONFIG_SYS_BR6_PRELIM 0 |
344 | #define CONFIG_SYS_OR6_PRELIM 0 | |
a562e1bd | 345 | |
6d0f6bcf JCPV |
346 | #define CONFIG_SYS_BR7_PRELIM 0x00000701 |
347 | #define CONFIG_SYS_OR7_PRELIM 0xFF00007C | |
a562e1bd WD |
348 | |
349 | /*----------------------------------------------------------------------- | |
350 | * LED config | |
351 | */ | |
352 | #define LED_STAT_0 0xffff /*all LEDs off*/ | |
353 | #define LED_STAT_1 0xfffe | |
354 | #define LED_STAT_2 0xfffd | |
355 | #define LED_STAT_3 0xfffb | |
356 | #define LED_STAT_4 0xfff7 | |
357 | #define LED_STAT_5 0xffef | |
358 | #define LED_STAT_6 0xffdf | |
359 | #define LED_STAT_7 0xff00 /*all LEDs on*/ | |
360 | ||
361 | /*----------------------------------------------------------------------- | |
362 | * Port configuration (GPIO) | |
363 | */ | |
6d0f6bcf | 364 | #define CONFIG_SYS_PACNT 0x00000000 /* PortA control reg.: All pins are external |
a562e1bd | 365 | GPIO*/ |
6d0f6bcf | 366 | #define CONFIG_SYS_PADDR 0x00FF /* PortA direction reg.: PA7 to PA0 are outputs |
a562e1bd | 367 | (1^=output, 0^=input) */ |
6d0f6bcf JCPV |
368 | #define CONFIG_SYS_PADAT LED_STAT_0 /* PortA value reg.: Turn all LED off */ |
369 | #define CONFIG_SYS_PBCNT 0x55554155 /* PortB control reg.: Ethernet/UART | |
a562e1bd | 370 | configuration */ |
6d0f6bcf JCPV |
371 | #define CONFIG_SYS_PBDDR 0x0000 /* PortB direction: All pins configured as inputs */ |
372 | #define CONFIG_SYS_PBDAT 0x0000 /* PortB value reg. */ | |
373 | #define CONFIG_SYS_PDCNT 0x00000000 /* PortD control reg. */ | |
a562e1bd WD |
374 | |
375 | #endif /* _CONFIG_COBRA5272_H */ |