[thirdparty/u-boot.git] / include / configs / gr_cpci_ax2000.h

/* Configuration header file for Gaisler GR-CPCI-AX2000
 * AX board. Note that since the AX is removable the configuration
 * for this board must be edited below.
 *
 * (C) Copyright 2003-2005
 * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
 *
 * (C) Copyright 2008
 * Daniel Hellstrom, Gaisler Research, daniel@gaisler.com.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_H__
#define __CONFIG_H__

#define CONFIG_SYS_GENERIC_BOARD
#define CONFIG_DISPLAY_BOARDINFO

/*
 * High Level Configuration Options
 * (easy to change)
 */

#define CONFIG_CPCI_AX2000	1	/* ... on GR-CPCI-AX2000 board */

#define CONFIG_LEON_RAM_SRAM 1
#define CONFIG_LEON_RAM_SDRAM 2
#define CONFIG_LEON_RAM_SDRAM_NOSRAM 3

/* Select Memory to run from
 *
 * SRAM          - UBoot is run in SRAM, SRAM-0x40000000, SDRAM-0x60000000
 * SDRAM         - UBoot is run in SDRAM, SRAM-0x40000000 and SDRAM-0x60000000
 * SDRAM_NOSRAM  - UBoot is run in SDRAM, SRAM not available, SDRAM at 0x40000000
 *
 * Note, if Linux is to be used, SDRAM or SDRAM_NOSRAM is required since
 * it doesn't fit into the 4Mb SRAM.
 *
 * SRAM is default since it will work for all systems, however will not
 * be able to boot linux.
 */
#define CONFIG_LEON_RAM_SELECT CONFIG_LEON_RAM_SRAM

/* CPU / AMBA BUS configuration */
#define CONFIG_SYS_CLK_FREQ	20000000	/* 20MHz */

/*
 * Serial console configuration
 */
#define CONFIG_BAUDRATE		38400	/* ... at 38400 bps */
#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }

/* Partitions */
#define CONFIG_DOS_PARTITION
#define CONFIG_MAC_PARTITION
#define CONFIG_ISO_PARTITION

/*
 * Supported commands
 */
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_DIAG
#define CONFIG_CMD_IRQ

/*
 * Autobooting
 */
#define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds */

#define CONFIG_PREBOOT	"echo;"	\
	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
	"echo"

#undef	CONFIG_BOOTARGS

#define	CONFIG_EXTRA_ENV_SETTINGS_BASE					\
	"netdev=eth0\0"							\
	"nfsargs=setenv bootargs console=ttyS0,38400 root=/dev/nfs rw "	\
		"nfsroot=${serverip}:${rootpath}\0"			\
	"ramargs=setenv bootargs console=ttyS0,${baudrate} root=/dev/ram rw\0"			\
	"addip=setenv bootargs ${bootargs} "				\
		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
		":${hostname}:${netdev}:off panic=1\0"			\
	"flash_nfs=run nfsargs addip;"					\
		"bootm ${kernel_addr}\0"				\
	"flash_self=run ramargs addip;"					\
		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
	"getkernel=tftpboot $(scratch) $(bootfile)\0" \
	"bootargs=console=ttyS0,38400 root=/dev/nfs rw nfsroot=192.168.0.20:/export/rootfs ip=192.168.0.206:192.168.0.20:192.168.0.1:255.255.255.0:ax2000:eth0\0"

#if CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SRAM
#define CONFIG_EXTRA_ENV_SETTINGS_SELECT \
	"net_nfs=tftp 40000000 ${bootfile};run nfsargs addip;bootm\0"	\
	"scratch=40200000\0"					\
	""
#elif CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SDRAM
#define CONFIG_EXTRA_ENV_SETTINGS_SELECT \
	"net_nfs=tftp 60000000 ${bootfile};run nfsargs addip;bootm\0"	\
	"scratch=60800000\0"					\
	""
#else
/* More than 4Mb is assumed when running from SDRAM */
#define CONFIG_EXTRA_ENV_SETTINGS_SELECT \
	"net_nfs=tftp 40000000 ${bootfile};run nfsargs addip;bootm\0"	\
	"scratch=40800000\0"					\
	""
#endif

#define	CONFIG_EXTRA_ENV_SETTINGS CONFIG_EXTRA_ENV_SETTINGS_BASE CONFIG_EXTRA_ENV_SETTINGS_SELECT

#define CONFIG_NETMASK 255.255.255.0
#define CONFIG_GATEWAYIP 192.168.0.1
#define CONFIG_SERVERIP 192.168.0.20
#define CONFIG_IPADDR 192.168.0.206
#define CONFIG_ROOTPATH "/export/rootfs"
#define CONFIG_HOSTNAME  ax2000
#define CONFIG_BOOTFILE "/uImage"

#define CONFIG_BOOTCOMMAND	"run flash_self"

/* Memory MAP
 *
 *  Flash:
 *  |--------------------------------|
 *  | 0x00000000 Text & Data & BSS   | *
 *  |            for Monitor         | *
 *  | ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~| *
 *  | UNUSED / Growth                | * 256kb
 *  |--------------------------------|
 *  | 0x00050000 Base custom area    | *
 *  |            kernel / FS         | *
 *  |                                | * Rest of Flash
 *  |~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~|
 *  | END-0x00008000 Environment     | * 32kb
 *  |--------------------------------|
 *
 *
 *
 *  Main Memory (4Mb SRAM or XMb SDRAM):
 *  |--------------------------------|
 *  | UNUSED / scratch area          |
 *  |                                |
 *  |                                |
 *  |                                |
 *  |                                |
 *  |--------------------------------|
 *  | Monitor .Text / .DATA / .BSS   | * 256kb
 *  | Relocated!                     | *
 *  |--------------------------------|
 *  | Monitor Malloc                 | * 128kb (contains relocated environment)
 *  |--------------------------------|
 *  | Monitor/kernel STACK           | * 64kb
 *  |--------------------------------|
 *  | Page Table for MMU systems     | * 2k
 *  |--------------------------------|
 *  | PROM Code accessed from Linux  | * 6kb-128b
 *  |--------------------------------|
 *  | Global data (avail from kernel)| * 128b
 *  |--------------------------------|
 *
 */

/*
 * Flash configuration (8,16 or 32 MB)
 * TEXT base always at 0xFFF00000
 * ENV_ADDR always at  0xFFF40000
 * FLASH_BASE at 0xFC000000 for 64 MB
 *               0xFE000000 for 32 MB
 *               0xFF000000 for 16 MB
 *               0xFF800000 for  8 MB
 */
/*#define CONFIG_SYS_NO_FLASH		1*/
#define CONFIG_SYS_FLASH_BASE		0x00000000
#define CONFIG_SYS_FLASH_SIZE		0x00800000

#define PHYS_FLASH_SECT_SIZE	0x00020000	/* 128 KB sectors */
#define CONFIG_SYS_MAX_FLASH_SECT	64	/* max num of sects on one chip */
#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of memory banks      */

#define CONFIG_SYS_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)  */
#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)  */
#define CONFIG_SYS_FLASH_LOCK_TOUT	5	/* Timeout for Flash Set Lock Bit (in ms) */
#define CONFIG_SYS_FLASH_UNLOCK_TOUT	10000	/* Timeout for Flash Clear Lock Bits (in ms) */
#define CONFIG_SYS_FLASH_PROTECTION	/* "Real" (hardware) sectors protection */

/*** CFI CONFIG ***/
#define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_8BIT
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_CFI
/* Bypass cache when reading regs from flash memory */
#define CONFIG_SYS_FLASH_CFI_BYPASS_READ
/* Buffered writes (32byte/go) instead of single accesses */
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE

/*
 * Environment settings
 */
/*#define CONFIG_ENV_IS_NOWHERE 1*/
#define CONFIG_ENV_IS_IN_FLASH	1
/* CONFIG_ENV_ADDR need to be at sector boundary */
#define CONFIG_ENV_SIZE		0x8000
#define CONFIG_ENV_SECT_SIZE	0x20000
#define CONFIG_ENV_ADDR		(CONFIG_SYS_FLASH_BASE+CONFIG_SYS_FLASH_SIZE-CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_OVERWRITE	1

/*
 * Memory map
 *
 * Always 4Mb SRAM available
 * SDRAM module may be available on 0x60000000, SDRAM
 * is configured as if a 128Mb SDRAM module is available.
 */

#if CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SDRAM_NOSRAM
#define CONFIG_SYS_SDRAM_BASE		0x40000000
#else
#define CONFIG_SYS_SDRAM_BASE		0x60000000
#endif

#define CONFIG_SYS_SDRAM_SIZE		0x08000000
#define CONFIG_SYS_SDRAM_END		(CONFIG_SYS_SDRAM_BASE+CONFIG_SYS_SDRAM_SIZE)

/* 4Mb SRAM available */
#if CONFIG_LEON_RAM_SELECT != CONFIG_LEON_RAM_SDRAM_NOSRAM
#define CONFIG_SYS_SRAM_BASE 0x40000000
#define CONFIG_SYS_SRAM_SIZE 0x400000
#define CONFIG_SYS_SRAM_END  (CONFIG_SYS_SRAM_BASE+CONFIG_SYS_SRAM_SIZE)
#endif

/* Select RAM used to run U-BOOT from... */
#if CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SRAM
#define CONFIG_SYS_RAM_BASE CONFIG_SYS_SRAM_BASE
#define CONFIG_SYS_RAM_SIZE CONFIG_SYS_SRAM_SIZE
#define CONFIG_SYS_RAM_END CONFIG_SYS_SRAM_END
#else
#define CONFIG_SYS_RAM_BASE CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_RAM_SIZE CONFIG_SYS_SDRAM_SIZE
#define CONFIG_SYS_RAM_END CONFIG_SYS_SDRAM_END
#endif

#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_RAM_END - GENERATED_GBL_DATA_SIZE)

#define CONFIG_SYS_PROM_SIZE		(8192-GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_PROM_OFFSET		(CONFIG_SYS_GBL_DATA_OFFSET-CONFIG_SYS_PROM_SIZE)

#define CONFIG_SYS_INIT_SP_OFFSET	(CONFIG_SYS_PROM_OFFSET-32)
#define CONFIG_SYS_STACK_SIZE		(0x10000-32)

#define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
#   define CONFIG_SYS_RAMBOOT		1
#endif

#define CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor   */
#define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()  */
#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */

#define CONFIG_SYS_MALLOC_END		(CONFIG_SYS_INIT_SP_OFFSET-CONFIG_SYS_STACK_SIZE)
#define CONFIG_SYS_MALLOC_BASE		(CONFIG_SYS_MALLOC_END-CONFIG_SYS_MALLOC_LEN)

/* relocated monitor area */
#define CONFIG_SYS_RELOC_MONITOR_MAX_END   CONFIG_SYS_MALLOC_BASE
#define CONFIG_SYS_RELOC_MONITOR_BASE     (CONFIG_SYS_RELOC_MONITOR_MAX_END-CONFIG_SYS_MONITOR_LEN)

/* make un relocated address from relocated address */
#define UN_RELOC(address) (address-(CONFIG_SYS_RELOC_MONITOR_BASE-CONFIG_SYS_TEXT_BASE))

/*
 * Ethernet configuration uses on board SMC91C111
 */
#define CONFIG_SMC91111          1
#define CONFIG_SMC91111_BASE		0x20000300	/* chip select 3         */
#define CONFIG_SMC_USE_32_BIT		1	/* 32 bit bus  */
#undef  CONFIG_SMC_91111_EXT_PHY	/* we use internal phy   */
/*#define CONFIG_SHOW_ACTIVITY*/
#define CONFIG_NET_RETRY_COUNT		10	/* # of retries          */

#define CONFIG_PHY_ADDR	 0x00

/*
 * Miscellaneous configurable options
 */
#define CONFIG_SYS_LONGHELP		/* undef to save memory     */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
#else
#define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
#define CONFIG_SYS_MAXARGS		16	/* max number of command args   */
#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size    */

#define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on */
#define CONFIG_SYS_MEMTEST_END		0x00f00000	/* 1 ... 15 MB in DRAM  */

#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */

/*
 * Various low-level settings
 */

/*-----------------------------------------------------------------------
 * USB stuff
 *-----------------------------------------------------------------------
 */
#define CONFIG_USB_CLOCK	0x0001BBBB
#define CONFIG_USB_CONFIG	0x00005000

/***** Gaisler GRLIB IP-Cores Config ********/

#define CONFIG_SYS_GRLIB_SDRAM    0

/* No SDRAM Configuration */
#undef CONFIG_SYS_GRLIB_GAISLER_SDCTRL1

/* See, GRLIB Docs (grip.pdf) on how to set up
 * These the memory controller registers.
 */
#define CONFIG_SYS_GRLIB_ESA_MCTRL1
#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG1   (0x10f800ff | (1<<11))
#if CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SDRAM_NOSRAM
#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2   0x82206000
#else
#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2   0x82205260
#endif
#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG3   0x0809a000

/* GRLIB FT-MCTRL configuration */
#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1
#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG1   (0x10f800ff | (1<<11))
#if CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SDRAM_NOSRAM
#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG2   0x82206000
#else
#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG2   0x82205260
#endif
#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG3   0x0809a000

/* no DDR controller */
#undef CONFIG_SYS_GRLIB_GAISLER_DDRSPA1

/* no DDR2 Controller */
#undef CONFIG_SYS_GRLIB_GAISLER_DDR2SPA1

/* Identification string */
#define CONFIG_IDENT_STRING " Gaisler LEON3 GR-CPCI-AX2000"

/* default kernel command line */
#define CONFIG_DEFAULT_KERNEL_COMMAND_LINE "console=ttyS0,38400\0\0"

#endif				/* __CONFIG_H */
Commit	Line	Data
6ed8a43a DH	1	/* Configuration header file for Gaisler GR-CPCI-AX2000
	2	* AX board. Note that since the AX is removable the configuration
	3	* for this board must be edited below.
	4	*
	5	* (C) Copyright 2003-2005
	6	* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
	7	*
	8	* (C) Copyright 2008
	9	* Daniel Hellstrom, Gaisler Research, daniel@gaisler.com.
	10	*
3765b3e7	11	* SPDX-License-Identifier: GPL-2.0+
6ed8a43a DH	12	*/
	13
	14	#ifndef __CONFIG_H__
	15	#define __CONFIG_H__
	16
a62bba15	17	#define CONFIG_SYS_GENERIC_BOARD
4c547754	18	#define CONFIG_DISPLAY_BOARDINFO
a62bba15	19
6ed8a43a DH	20	/*
	21	* High Level Configuration Options
	22	* (easy to change)
	23	*/
	24
6ed8a43a DH	25	#define CONFIG_CPCI_AX2000 1 /* ... on GR-CPCI-AX2000 board */
	26
	27	#define CONFIG_LEON_RAM_SRAM 1
	28	#define CONFIG_LEON_RAM_SDRAM 2
	29	#define CONFIG_LEON_RAM_SDRAM_NOSRAM 3
	30
	31	/* Select Memory to run from
	32	*
	33	* SRAM - UBoot is run in SRAM, SRAM-0x40000000, SDRAM-0x60000000
	34	* SDRAM - UBoot is run in SDRAM, SRAM-0x40000000 and SDRAM-0x60000000
	35	* SDRAM_NOSRAM - UBoot is run in SDRAM, SRAM not available, SDRAM at 0x40000000
	36	*
	37	* Note, if Linux is to be used, SDRAM or SDRAM_NOSRAM is required since
	38	* it doesn't fit into the 4Mb SRAM.
	39	*
	40	* SRAM is default since it will work for all systems, however will not
	41	* be able to boot linux.
	42	*/
	43	#define CONFIG_LEON_RAM_SELECT CONFIG_LEON_RAM_SRAM
	44
	45	/* CPU / AMBA BUS configuration */
53677ef1	46	#define CONFIG_SYS_CLK_FREQ 20000000 /* 20MHz */
6ed8a43a	47
6ed8a43a DH	48	/*
	49	* Serial console configuration
	50	*/
	51	#define CONFIG_BAUDRATE 38400 /* ... at 38400 bps */
6d0f6bcf	52	#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }
6ed8a43a DH	53
	54	/* Partitions */
	55	#define CONFIG_DOS_PARTITION
	56	#define CONFIG_MAC_PARTITION
	57	#define CONFIG_ISO_PARTITION
	58
	59	/*
	60	* Supported commands
	61	*/
6ed8a43a	62	#define CONFIG_CMD_REGINFO
6ed8a43a DH	63	#define CONFIG_CMD_DIAG
	64	#define CONFIG_CMD_IRQ
	65
	66	/*
	67	* Autobooting
	68	*/
	69	#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
	70
	71	#define CONFIG_PREBOOT "echo;" \
	72	"echo Type \"run flash_nfs\" to mount root filesystem over NFS;" \
	73	"echo"
	74
	75	#undef CONFIG_BOOTARGS
	76
	77	#define CONFIG_EXTRA_ENV_SETTINGS_BASE \
	78	"netdev=eth0\0" \
	79	"nfsargs=setenv bootargs console=ttyS0,38400 root=/dev/nfs rw " \
	80	"nfsroot=${serverip}:${rootpath}\0" \
	81	"ramargs=setenv bootargs console=ttyS0,${baudrate} root=/dev/ram rw\0" \
	82	"addip=setenv bootargs ${bootargs} " \
	83	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
	84	":${hostname}:${netdev}:off panic=1\0" \
	85	"flash_nfs=run nfsargs addip;" \
	86	"bootm ${kernel_addr}\0" \
	87	"flash_self=run ramargs addip;" \
	88	"bootm ${kernel_addr} ${ramdisk_addr}\0" \
3a2b9f28	89	"getkernel=tftpboot $(scratch) $(bootfile)\0" \
6ed8a43a DH	90	"bootargs=console=ttyS0,38400 root=/dev/nfs rw nfsroot=192.168.0.20:/export/rootfs ip=192.168.0.206:192.168.0.20:192.168.0.1:255.255.255.0:ax2000:eth0\0"
	91
	92	#if CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SRAM
	93	#define CONFIG_EXTRA_ENV_SETTINGS_SELECT \
	94	"net_nfs=tftp 40000000 ${bootfile};run nfsargs addip;bootm\0" \
	95	"scratch=40200000\0" \
	96	""
	97	#elif CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SDRAM
	98	#define CONFIG_EXTRA_ENV_SETTINGS_SELECT \
	99	"net_nfs=tftp 60000000 ${bootfile};run nfsargs addip;bootm\0" \
	100	"scratch=60800000\0" \
	101	""
	102	#else
	103	/* More than 4Mb is assumed when running from SDRAM */
	104	#define CONFIG_EXTRA_ENV_SETTINGS_SELECT \
	105	"net_nfs=tftp 40000000 ${bootfile};run nfsargs addip;bootm\0" \
	106	"scratch=40800000\0" \
	107	""
	108	#endif
	109
	110	#define CONFIG_EXTRA_ENV_SETTINGS CONFIG_EXTRA_ENV_SETTINGS_BASE CONFIG_EXTRA_ENV_SETTINGS_SELECT
	111
	112	#define CONFIG_NETMASK 255.255.255.0
	113	#define CONFIG_GATEWAYIP 192.168.0.1
	114	#define CONFIG_SERVERIP 192.168.0.20
	115	#define CONFIG_IPADDR 192.168.0.206
8b3637c6	116	#define CONFIG_ROOTPATH "/export/rootfs"
6ed8a43a	117	#define CONFIG_HOSTNAME ax2000
b3f44c21	118	#define CONFIG_BOOTFILE "/uImage"
6ed8a43a DH	119
	120	#define CONFIG_BOOTCOMMAND "run flash_self"
	121
	122	/* Memory MAP
	123	*
	124	* Flash:
	125	* \|--------------------------------\|
	126	* \| 0x00000000 Text & Data & BSS \| *
	127	* \| for Monitor \| *
	128	* \| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~\| *
	129	* \| UNUSED / Growth \| * 256kb
	130	* \|--------------------------------\|
	131	* \| 0x00050000 Base custom area \| *
	132	* \| kernel / FS \| *
	133	* \| \| * Rest of Flash
	134	* \|~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~\|
	135	* \| END-0x00008000 Environment \| * 32kb
	136	* \|--------------------------------\|
	137	*
	138	*
	139	*
	140	* Main Memory (4Mb SRAM or XMb SDRAM):
	141	* \|--------------------------------\|
	142	* \| UNUSED / scratch area \|
	143	* \| \|
	144	* \| \|
	145	* \| \|
	146	* \| \|
	147	* \|--------------------------------\|
	148	* \| Monitor .Text / .DATA / .BSS \| * 256kb
	149	* \| Relocated! \| *
	150	* \|--------------------------------\|
	151	* \| Monitor Malloc \| * 128kb (contains relocated environment)
	152	* \|--------------------------------\|
	153	* \| Monitor/kernel STACK \| * 64kb
	154	* \|--------------------------------\|
	155	* \| Page Table for MMU systems \| * 2k
	156	* \|--------------------------------\|
	157	* \| PROM Code accessed from Linux \| * 6kb-128b
	158	* \|--------------------------------\|
	159	* \| Global data (avail from kernel)\| * 128b
	160	* \|--------------------------------\|
	161	*
	162	*/
	163
	164	/*
	165	* Flash configuration (8,16 or 32 MB)
	166	* TEXT base always at 0xFFF00000
	167	* ENV_ADDR always at 0xFFF40000
	168	* FLASH_BASE at 0xFC000000 for 64 MB
	169	* 0xFE000000 for 32 MB
	170	* 0xFF000000 for 16 MB
	171	* 0xFF800000 for 8 MB
	172	*/
6d0f6bcf JCPV	173	/#define CONFIG_SYS_NO_FLASH 1/
	174	#define CONFIG_SYS_FLASH_BASE 0x00000000
	175	#define CONFIG_SYS_FLASH_SIZE 0x00800000
6ed8a43a DH	176
6ed8a43a DH	177	#define PHYS_FLASH_SECT_SIZE 0x00020000 /* 128 KB sectors */
6d0f6bcf JCPV	178	#define CONFIG_SYS_MAX_FLASH_SECT 64 /* max num of sects on one chip */
6d0f6bcf JCPV	179	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of memory banks */
6ed8a43a	180
6d0f6bcf JCPV	181	#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
	182	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */
	183	#define CONFIG_SYS_FLASH_LOCK_TOUT 5 /* Timeout for Flash Set Lock Bit (in ms) */
	184	#define CONFIG_SYS_FLASH_UNLOCK_TOUT 10000 /* Timeout for Flash Clear Lock Bits (in ms) */
	185	#define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */
6ed8a43a DH	186
6ed8a43a DH	187	/* CFI CONFIG */
6d0f6bcf	188	#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT
00b1883a	189	#define CONFIG_FLASH_CFI_DRIVER
6d0f6bcf	190	#define CONFIG_SYS_FLASH_CFI
6ed8a43a	191	/* Bypass cache when reading regs from flash memory */
6d0f6bcf	192	#define CONFIG_SYS_FLASH_CFI_BYPASS_READ
6ed8a43a	193	/* Buffered writes (32byte/go) instead of single accesses */
6d0f6bcf	194	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
6ed8a43a DH	195
	196	/*
	197	* Environment settings
	198	*/
93f6d725	199	/#define CONFIG_ENV_IS_NOWHERE 1/
5a1aceb0	200	#define CONFIG_ENV_IS_IN_FLASH 1
0e8d1586 JCPV	201	/* CONFIG_ENV_ADDR need to be at sector boundary */
	202	#define CONFIG_ENV_SIZE 0x8000
	203	#define CONFIG_ENV_SECT_SIZE 0x20000
6d0f6bcf	204	#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE+CONFIG_SYS_FLASH_SIZE-CONFIG_ENV_SECT_SIZE)
6ed8a43a DH	205	#define CONFIG_ENV_OVERWRITE 1
	206
	207	/*
	208	* Memory map
	209	*
	210	* Always 4Mb SRAM available
	211	* SDRAM module may be available on 0x60000000, SDRAM
	212	* is configured as if a 128Mb SDRAM module is available.
	213	*/
	214
	215	#if CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SDRAM_NOSRAM
6d0f6bcf	216	#define CONFIG_SYS_SDRAM_BASE 0x40000000
6ed8a43a	217	#else
6d0f6bcf	218	#define CONFIG_SYS_SDRAM_BASE 0x60000000
6ed8a43a DH	219	#endif
6ed8a43a DH	220
6d0f6bcf JCPV	221	#define CONFIG_SYS_SDRAM_SIZE 0x08000000
6d0f6bcf JCPV	222	#define CONFIG_SYS_SDRAM_END (CONFIG_SYS_SDRAM_BASE+CONFIG_SYS_SDRAM_SIZE)
6ed8a43a DH	223
	224	/* 4Mb SRAM available */
	225	#if CONFIG_LEON_RAM_SELECT != CONFIG_LEON_RAM_SDRAM_NOSRAM
6d0f6bcf JCPV	226	#define CONFIG_SYS_SRAM_BASE 0x40000000
	227	#define CONFIG_SYS_SRAM_SIZE 0x400000
	228	#define CONFIG_SYS_SRAM_END (CONFIG_SYS_SRAM_BASE+CONFIG_SYS_SRAM_SIZE)
6ed8a43a DH	229	#endif
	230
	231	/* Select RAM used to run U-BOOT from... */
	232	#if CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SRAM
6d0f6bcf JCPV	233	#define CONFIG_SYS_RAM_BASE CONFIG_SYS_SRAM_BASE
	234	#define CONFIG_SYS_RAM_SIZE CONFIG_SYS_SRAM_SIZE
	235	#define CONFIG_SYS_RAM_END CONFIG_SYS_SRAM_END
6ed8a43a	236	#else
6d0f6bcf JCPV	237	#define CONFIG_SYS_RAM_BASE CONFIG_SYS_SDRAM_BASE
	238	#define CONFIG_SYS_RAM_SIZE CONFIG_SYS_SDRAM_SIZE
	239	#define CONFIG_SYS_RAM_END CONFIG_SYS_SDRAM_END
6ed8a43a DH	240	#endif
6ed8a43a DH	241
25ddd1fb	242	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_RAM_END - GENERATED_GBL_DATA_SIZE)
6ed8a43a	243
25ddd1fb	244	#define CONFIG_SYS_PROM_SIZE (8192-GENERATED_GBL_DATA_SIZE)
6d0f6bcf	245	#define CONFIG_SYS_PROM_OFFSET (CONFIG_SYS_GBL_DATA_OFFSET-CONFIG_SYS_PROM_SIZE)
6ed8a43a	246
6d0f6bcf JCPV	247	#define CONFIG_SYS_INIT_SP_OFFSET (CONFIG_SYS_PROM_OFFSET-32)
6d0f6bcf JCPV	248	#define CONFIG_SYS_STACK_SIZE (0x10000-32)
6ed8a43a	249
14d0a02a	250	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
6d0f6bcf JCPV	251	#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
6d0f6bcf JCPV	252	# define CONFIG_SYS_RAMBOOT 1
6ed8a43a DH	253	#endif
6ed8a43a DH	254
6d0f6bcf JCPV	255	#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
	256	#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
	257	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
6ed8a43a	258
6d0f6bcf JCPV	259	#define CONFIG_SYS_MALLOC_END (CONFIG_SYS_INIT_SP_OFFSET-CONFIG_SYS_STACK_SIZE)
6d0f6bcf JCPV	260	#define CONFIG_SYS_MALLOC_BASE (CONFIG_SYS_MALLOC_END-CONFIG_SYS_MALLOC_LEN)
6ed8a43a DH	261
6ed8a43a DH	262	/* relocated monitor area */
6d0f6bcf JCPV	263	#define CONFIG_SYS_RELOC_MONITOR_MAX_END CONFIG_SYS_MALLOC_BASE
6d0f6bcf JCPV	264	#define CONFIG_SYS_RELOC_MONITOR_BASE (CONFIG_SYS_RELOC_MONITOR_MAX_END-CONFIG_SYS_MONITOR_LEN)
6ed8a43a DH	265
6ed8a43a DH	266	/* make un relocated address from relocated address */
14d0a02a	267	#define UN_RELOC(address) (address-(CONFIG_SYS_RELOC_MONITOR_BASE-CONFIG_SYS_TEXT_BASE))
6ed8a43a DH	268
	269	/*
	270	* Ethernet configuration uses on board SMC91C111
	271	*/
7194ab80	272	#define CONFIG_SMC91111 1
6ed8a43a DH	273	#define CONFIG_SMC91111_BASE 0x20000300 /* chip select 3 */
	274	#define CONFIG_SMC_USE_32_BIT 1 /* 32 bit bus */
	275	#undef CONFIG_SMC_91111_EXT_PHY /* we use internal phy */
	276	/#define CONFIG_SHOW_ACTIVITY/
	277	#define CONFIG_NET_RETRY_COUNT 10 /* # of retries */
	278
6ed8a43a DH	279	#define CONFIG_PHY_ADDR 0x00
	280
	281	/*
	282	* Miscellaneous configurable options
	283	*/
6d0f6bcf	284	#define CONFIG_SYS_LONGHELP /* undef to save memory */
6ed8a43a	285	#if defined(CONFIG_CMD_KGDB)
6d0f6bcf	286	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
6ed8a43a	287	#else
6d0f6bcf	288	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
6ed8a43a	289	#endif
6d0f6bcf JCPV	290	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	291	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	292	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
6ed8a43a	293
6d0f6bcf JCPV	294	#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
6d0f6bcf JCPV	295	#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
6ed8a43a	296
6d0f6bcf	297	#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
6ed8a43a	298
6ed8a43a DH	299	/*
	300	* Various low-level settings
	301	*/
	302
	303	/*-----------------------------------------------------------------------
	304	* USB stuff
	305	*-----------------------------------------------------------------------
	306	*/
	307	#define CONFIG_USB_CLOCK 0x0001BBBB
	308	#define CONFIG_USB_CONFIG 0x00005000
	309
	310	/*** Gaisler GRLIB IP-Cores Config ******/
	311
6d0f6bcf	312	#define CONFIG_SYS_GRLIB_SDRAM 0
6ed8a43a	313
cff009ed DH	314	/* No SDRAM Configuration */
	315	#undef CONFIG_SYS_GRLIB_GAISLER_SDCTRL1
	316
6ed8a43a DH	317	/* See, GRLIB Docs (grip.pdf) on how to set up
	318	* These the memory controller registers.
	319	*/
cff009ed DH	320	#define CONFIG_SYS_GRLIB_ESA_MCTRL1
cff009ed DH	321	#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG1 (0x10f800ff \| (1<<11))
6ed8a43a	322	#if CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SDRAM_NOSRAM
cff009ed	323	#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2 0x82206000
6ed8a43a	324	#else
cff009ed	325	#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG2 0x82205260
6ed8a43a	326	#endif
cff009ed	327	#define CONFIG_SYS_GRLIB_ESA_MCTRL1_CFG3 0x0809a000
6ed8a43a	328
cff009ed DH	329	/* GRLIB FT-MCTRL configuration */
	330	#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1
	331	#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG1 (0x10f800ff \| (1<<11))
6ed8a43a	332	#if CONFIG_LEON_RAM_SELECT == CONFIG_LEON_RAM_SDRAM_NOSRAM
cff009ed	333	#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG2 0x82206000
6ed8a43a	334	#else
cff009ed	335	#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG2 0x82205260
6ed8a43a	336	#endif
cff009ed	337	#define CONFIG_SYS_GRLIB_GAISLER_FTMCTRL1_CFG3 0x0809a000
6ed8a43a DH	338
6ed8a43a DH	339	/* no DDR controller */
cff009ed	340	#undef CONFIG_SYS_GRLIB_GAISLER_DDRSPA1
6ed8a43a DH	341
6ed8a43a DH	342	/* no DDR2 Controller */
cff009ed	343	#undef CONFIG_SYS_GRLIB_GAISLER_DDR2SPA1
6ed8a43a	344
6ed8a43a	345	/* Identification string */
4c547754	346	#define CONFIG_IDENT_STRING " Gaisler LEON3 GR-CPCI-AX2000"
6ed8a43a DH	347
	348	/* default kernel command line */
	349	#define CONFIG_DEFAULT_KERNEL_COMMAND_LINE "console=ttyS0,38400\0\0"
	350
	351	#endif /* __CONFIG_H */