projects / people / ms / u-boot.git / blame
| Commit | Line | Data |
|---|---|---|
| dd02936f MH |
1 | /* |
| 2 | * Copyright 2016 Freescale Semiconductor | |
| 3 | * | |
| 4 | * SPDX-License-Identifier: GPL-2.0+ | |
| 5 | */ | |
| 6 | ||
| 7 | #ifndef __LS1046A_COMMON_H | |
| 8 | #define __LS1046A_COMMON_H | |
| 9 | ||
| 10 | #define CONFIG_REMAKE_ELF | |
| 11 | #define CONFIG_FSL_LAYERSCAPE | |
| dd02936f MH |
12 | #define CONFIG_MP |
| 13 | #define CONFIG_SYS_FSL_CLK | |
| 14 | #define CONFIG_GICV2 | |
| 15 | ||
| 16 | #include <asm/arch/config.h> | |
| dd02936f MH |
17 | |
| 18 | /* Link Definitions */ | |
| 19 | #define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0) | |
| 20 | ||
| 21 | #define CONFIG_SUPPORT_RAW_INITRD | |
| 22 | ||
| 23 | #define CONFIG_SKIP_LOWLEVEL_INIT | |
| 24 | #define CONFIG_BOARD_EARLY_INIT_F 1 | |
| 25 | ||
| 26 | #define CONFIG_VERY_BIG_RAM | |
| 27 | #define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000 | |
| 28 | #define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0 | |
| 29 | #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE | |
| 30 | #define CONFIG_SYS_DDR_BLOCK2_BASE 0x880000000ULL | |
| 31 | ||
| 32 | #define CPU_RELEASE_ADDR secondary_boot_func | |
| 33 | ||
| 34 | /* Generic Timer Definitions */ | |
| 35 | #define COUNTER_FREQUENCY 25000000 /* 25MHz */ | |
| 36 | ||
| 37 | /* Size of malloc() pool */ | |
| 38 | #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1024 * 1024) | |
| 39 | ||
| 40 | /* Serial Port */ | |
| 41 | #define CONFIG_CONS_INDEX 1 | |
| 42 | #define CONFIG_SYS_NS16550_SERIAL | |
| 43 | #define CONFIG_SYS_NS16550_REG_SIZE 1 | |
| 44 | #define CONFIG_SYS_NS16550_CLK (get_bus_freq(0)/2) | |
| 45 | ||
| 46 | #define CONFIG_BAUDRATE 115200 | |
| 47 | #define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 } | |
| 48 | ||
| 49 | /* SD boot SPL */ | |
| 50 | #ifdef CONFIG_SD_BOOT | |
| 51 | #define CONFIG_SPL_FRAMEWORK | |
| 52 | #define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds" | |
| 53 | #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" | |
| 54 | #define CONFIG_SPL_LIBCOMMON_SUPPORT | |
| 55 | #define CONFIG_SPL_LIBGENERIC_SUPPORT | |
| 56 | #define CONFIG_SPL_ENV_SUPPORT | |
| 57 | #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT | |
| 58 | #define CONFIG_SPL_WATCHDOG_SUPPORT | |
| 59 | #define CONFIG_SPL_I2C_SUPPORT | |
| 60 | #define CONFIG_SPL_SERIAL_SUPPORT | |
| 61 | #define CONFIG_SPL_DRIVERS_MISC_SUPPORT | |
| 62 | ||
| 63 | #define CONFIG_SPL_MMC_SUPPORT | |
| dd02936f MH |
64 | #define CONFIG_SPL_TEXT_BASE 0x10000000 |
| 65 | #define CONFIG_SPL_MAX_SIZE 0x1f000 /* 124 KiB */ | |
| 66 | #define CONFIG_SPL_STACK 0x10020000 | |
| 67 | #define CONFIG_SPL_PAD_TO 0x21000 /* 132 KiB */ | |
| 68 | #define CONFIG_SPL_BSS_START_ADDR 0x8f000000 | |
| 69 | #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 | |
| 70 | #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \ | |
| 71 | CONFIG_SPL_BSS_MAX_SIZE) | |
| 72 | #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 | |
| 73 | #define CONFIG_SYS_MONITOR_LEN 0xa0000 | |
| 74 | #endif | |
| 75 | ||
| 126fe70d SX |
76 | /* NAND SPL */ |
| 77 | #ifdef CONFIG_NAND_BOOT | |
| 78 | #define CONFIG_SPL_PBL_PAD | |
| 79 | #define CONFIG_SPL_FRAMEWORK | |
| 80 | #define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds" | |
| 81 | #define CONFIG_SPL_TARGET "u-boot-with-spl.bin" | |
| 82 | #define CONFIG_SPL_LIBCOMMON_SUPPORT | |
| 83 | #define CONFIG_SPL_LIBGENERIC_SUPPORT | |
| 84 | #define CONFIG_SPL_ENV_SUPPORT | |
| 85 | #define CONFIG_SPL_WATCHDOG_SUPPORT | |
| 86 | #define CONFIG_SPL_I2C_SUPPORT | |
| 87 | #define CONFIG_SPL_SERIAL_SUPPORT | |
| 88 | #define CONFIG_SPL_MPC8XXX_INIT_DDR_SUPPORT | |
| 89 | ||
| 90 | #define CONFIG_SPL_NAND_SUPPORT | |
| 91 | #define CONFIG_SPL_DRIVERS_MISC_SUPPORT | |
| 92 | #define CONFIG_SPL_TEXT_BASE 0x10000000 | |
| 93 | #define CONFIG_SPL_MAX_SIZE 0x1d000 /* 116 KiB */ | |
| 94 | #define CONFIG_SPL_STACK 0x1001f000 | |
| 95 | #define CONFIG_SYS_NAND_U_BOOT_DST CONFIG_SYS_TEXT_BASE | |
| 96 | #define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE | |
| 97 | ||
| 98 | #define CONFIG_SPL_BSS_START_ADDR 0x8f000000 | |
| 99 | #define CONFIG_SPL_BSS_MAX_SIZE 0x80000 | |
| 100 | #define CONFIG_SYS_SPL_MALLOC_START (CONFIG_SPL_BSS_START_ADDR + \ | |
| 101 | CONFIG_SPL_BSS_MAX_SIZE) | |
| 102 | #define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000 | |
| 103 | #define CONFIG_SYS_MONITOR_LEN 0xa0000 | |
| 104 | #endif | |
| 105 | ||
| dd02936f MH |
106 | /* I2C */ |
| 107 | #define CONFIG_SYS_I2C | |
| 108 | #define CONFIG_SYS_I2C_MXC | |
| 109 | #define CONFIG_SYS_I2C_MXC_I2C1 | |
| 110 | #define CONFIG_SYS_I2C_MXC_I2C2 | |
| 111 | #define CONFIG_SYS_I2C_MXC_I2C3 | |
| 112 | #define CONFIG_SYS_I2C_MXC_I2C4 | |
| 113 | ||
| 114 | /* Command line configuration */ | |
| 115 | #define CONFIG_CMD_ENV | |
| 116 | ||
| 117 | /* MMC */ | |
| dd02936f MH |
118 | #ifdef CONFIG_MMC |
| 119 | #define CONFIG_FSL_ESDHC | |
| 120 | #define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33 | |
| 121 | #define CONFIG_GENERIC_MMC | |
| 122 | #define CONFIG_DOS_PARTITION | |
| 123 | #endif | |
| 124 | ||
| 125 | #define CONFIG_FSL_CAAM /* Enable SEC/CAAM */ | |
| 126 | ||
| 127 | #define CONFIG_SYS_DPAA_QBMAN /* Support Q/Bman */ | |
| 128 | ||
| 129 | /* FMan ucode */ | |
| 130 | #define CONFIG_SYS_DPAA_FMAN | |
| 131 | #ifdef CONFIG_SYS_DPAA_FMAN | |
| 132 | #define CONFIG_SYS_FM_MURAM_SIZE 0x60000 | |
| 133 | ||
| 134 | #ifdef CONFIG_SD_BOOT | |
| 135 | /* | |
| 136 | * PBL SD boot image should stored at 0x1000(8 blocks), the size of the image is | |
| 137 | * about 1MB (2048 blocks), Env is stored after the image, and the env size is | |
| 138 | * 0x2000 (16 blocks), 8 + 2048 + 16 = 2072, enlarge it to 2080(0x820). | |
| 139 | */ | |
| 140 | #define CONFIG_SYS_QE_FMAN_FW_IN_MMC | |
| 141 | #define CONFIG_SYS_FMAN_FW_ADDR (512 * 0x820) | |
| 126fe70d | 142 | #elif defined(CONFIG_QSPI_BOOT) |
| dd02936f MH |
143 | #define CONFIG_SYS_QE_FW_IN_SPIFLASH |
| 144 | #define CONFIG_SYS_FMAN_FW_ADDR 0x40300000 | |
| 145 | #define CONFIG_ENV_SPI_BUS 0 | |
| 146 | #define CONFIG_ENV_SPI_CS 0 | |
| 147 | #define CONFIG_ENV_SPI_MAX_HZ 1000000 | |
| 148 | #define CONFIG_ENV_SPI_MODE 0x03 | |
| 126fe70d SX |
149 | #elif defined(CONFIG_NAND_BOOT) |
| 150 | #define CONFIG_SYS_QE_FMAN_FW_IN_NAND | |
| 151 | #define CONFIG_SYS_FMAN_FW_ADDR (6 * CONFIG_SYS_NAND_BLOCK_SIZE) | |
| 152 | #else | |
| 153 | #define CONFIG_SYS_QE_FMAN_FW_IN_NOR | |
| 154 | #define CONFIG_SYS_FMAN_FW_ADDR 0x60300000 | |
| dd02936f MH |
155 | #endif |
| 156 | #define CONFIG_SYS_QE_FMAN_FW_LENGTH 0x10000 | |
| 157 | #define CONFIG_SYS_FDT_PAD (0x3000 + CONFIG_SYS_QE_FMAN_FW_LENGTH) | |
| 158 | #endif | |
| 159 | ||
| 160 | /* Miscellaneous configurable options */ | |
| 161 | #define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000) | |
| 162 | #define CONFIG_ARCH_EARLY_INIT_R | |
| 163 | #define CONFIG_BOARD_LATE_INIT | |
| 164 | ||
| 165 | #define CONFIG_HWCONFIG | |
| 166 | #define HWCONFIG_BUFFER_SIZE 128 | |
| 167 | ||
| 168 | /* Initial environment variables */ | |
| 169 | #define CONFIG_EXTRA_ENV_SETTINGS \ | |
| 170 | "hwconfig=fsl_ddr:bank_intlv=auto\0" \ | |
| 171 | "loadaddr=0x80100000\0" \ | |
| 172 | "ramdisk_addr=0x800000\0" \ | |
| 173 | "ramdisk_size=0x2000000\0" \ | |
| 174 | "fdt_high=0xffffffffffffffff\0" \ | |
| 175 | "initrd_high=0xffffffffffffffff\0" \ | |
| 176 | "kernel_start=0x1000000\0" \ | |
| 177 | "kernel_load=0xa0000000\0" \ | |
| 178 | "kernel_size=0x2800000\0" \ | |
| 179 | "console=ttyS0,115200\0" \ | |
| 180 | MTDPARTS_DEFAULT "\0" | |
| 181 | ||
| 182 | #define CONFIG_BOOTARGS "console=ttyS0,115200 root=/dev/ram0 " \ | |
| 183 | "earlycon=uart8250,mmio,0x21c0500 " \ | |
| 184 | MTDPARTS_DEFAULT | |
| 185 | /* Monitor Command Prompt */ | |
| 186 | #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ | |
| 187 | #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ | |
| 188 | sizeof(CONFIG_SYS_PROMPT) + 16) | |
| 189 | #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */ | |
| 190 | #define CONFIG_SYS_LONGHELP | |
| 191 | #define CONFIG_CMDLINE_EDITING 1 | |
| 192 | #define CONFIG_AUTO_COMPLETE | |
| 193 | #define CONFIG_SYS_MAXARGS 64 /* max command args */ | |
| 194 | ||
| 195 | #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */ | |
| 196 | ||
| 197 | /* Hash command with SHA acceleration supported in hardware */ | |
| 198 | #ifdef CONFIG_FSL_CAAM | |
| 199 | #define CONFIG_CMD_HASH | |
| 200 | #define CONFIG_SHA_HW_ACCEL | |
| 201 | #endif | |
| 202 | ||
| 203 | #endif /* __LS1046A_COMMON_H */ |