[people/ms/u-boot.git] / include / configs / mccmon6.h

/*
 * Copyright (C) 2016-2017
 * Lukasz Majewski, DENX Software Engineering, lukma@denx.de
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

#include <config_distro_defaults.h>
#include "mx6_common.h"

#define CONFIG_SPL_LIBCOMMON_SUPPORT
#include "imx6_spl.h"

#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_UBOOT_BASE (CONFIG_SYS_FLASH_BASE + 0x80000)
#define CONFIG_SPL_OS_BOOT
#define CONFIG_SYS_OS_BASE (CONFIG_SYS_FLASH_BASE + 0x180000)
#define CONFIG_SYS_FDT_BASE (CONFIG_SYS_FLASH_BASE + 0x1980000)
#define CONFIG_SYS_FDT_SIZE (48 * SZ_1K)
#define CONFIG_SYS_SPL_ARGS_ADDR	0x18000000

/*
 * Below defines are set but NOT really used since we by
 * design force U-Boot run when we boot in development
 * mode from SD card (SD2)
 */
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR (0x800)
#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS (0x80)
#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR (0x1000)
#define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage"
#define CONFIG_SPL_FS_LOAD_ARGS_NAME "imx6q-mccmon.dtb"

/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN		(10 * SZ_1M)

#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_LATE_INIT

#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE		UART1_BASE

#define CONFIG_SYS_MEMTEST_START	0x10000000
#define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + 500 * SZ_1M)

#define CONFIG_MXC_SPI
#define CONFIG_SF_DEFAULT_BUS  2
#define CONFIG_SF_DEFAULT_CS   0
#define CONFIG_SF_DEFAULT_SPEED 25000000
#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)

/* I2C Configs */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
#define CONFIG_SYS_I2C_SPEED		100000

/* MMC Configuration */
#define CONFIG_SYS_FSL_USDHC_NUM	2
#define CONFIG_SYS_FSL_ESDHC_ADDR	0

/* NOR 16-bit mode */
#define CONFIG_SYS_FLASH_BASE           WEIM_ARB_BASE_ADDR
#define CONFIG_SYS_FLASH_PROTECTION
#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
#define CONFIG_SYS_FLASH_CFI            /* Flash memory is CFI compliant */
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* Use buffered writes*/
#define CONFIG_SYS_FLASH_EMPTY_INFO
#define CONFIG_FLASH_CFI_DRIVER         /* Use drivers/cfi_flash.c */
#define CONFIG_FLASH_VERIFY

/* NOR Flash MTD */
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_FLASH_CFI_MTD
#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 1
#define CONFIG_SYS_FLASH_BANKS_LIST	{ (CONFIG_SYS_FLASH_BASE) }
#define CONFIG_SYS_FLASH_BANKS_SIZES	{ (32 * SZ_1M) }

/* MTD support */
#define CONFIG_MTD_DEVICE
#define CONFIG_MTD_PARTITIONS

/* USB Configs */
#define CONFIG_USB_MAX_CONTROLLER_COUNT	2
#define CONFIG_MXC_USB_PORTSC		(PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS		0

/* Ethernet Configuration */
#define CONFIG_FEC_MXC
#define CONFIG_MII
#define IMX_FEC_BASE			ENET_BASE_ADDR
#define CONFIG_FEC_XCV_TYPE		RGMII
#define CONFIG_ETHPRIME			"FEC"
#define CONFIG_FEC_MXC_PHYADDR		1

#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
#define CONFIG_EXTRA_ENV_SETTINGS \
	"console=ttymxc0,115200 quiet\0" \
	"fdtfile=imx6q-mccmon6.dtb\0" \
	"fdt_high=0xffffffff\0" \
	"initrd_high=0xffffffff\0" \
	"boot_os=yes\0" \
	"download_kernel=" \
		"tftpboot ${kernel_addr} ${kernel_file};" \
		"tftpboot ${fdt_addr} ${fdtfile};\0" \
	"get_boot_medium=" \
		"setenv boot_medium nor;" \
		"setexpr.l _src_sbmr1 *0x020d8004;" \
		"setexpr _b_medium ${_src_sbmr1} '&' 0x00000040;" \
		"if test ${_b_medium} = 40; then " \
			"setenv boot_medium sdcard;" \
		"fi\0" \
	"kernel_file=uImage\0" \
	"load_kernel=" \
		"load mmc ${bootdev}:${bootpart} ${kernel_addr} uImage;" \
		"load mmc ${bootdev}:${bootpart} ${fdt_addr} ${fdtfile};\0" \
	"boot_sd=" \
		"echo '#######################';" \
		"echo '# Factory SDcard Boot #';" \
		"echo '#######################';" \
		"setenv mmcdev 1;" \
		"setenv mmcfactorydev 0;" \
		"setenv mmcfactorypart 1;" \
		"run factory_flash_img;\0" \
	"boot_nor=" \
		"setenv kernelnor 0x08180000;" \
		"setenv dtbnor 0x09980000;" \
		"setenv bootargs console=${console} " \
		CONFIG_MTDPARTS_DEFAULT " " \
		"root=/dev/mmcblk1 rootfstype=ext4 rw rootwait noinitrd;" \
		"cp.l ${dtbnor} ${dtbloadaddr} 0x8000;" \
		"bootm ${kernelnor} - ${dtbloadaddr};\0" \
	"boot_recovery=" \
		"echo '#######################';" \
		"echo '# RECOVERY SWU Boot   #';" \
		"echo '#######################';" \
		"setenv rootfsloadaddr 0x13000000;" \
		"setenv swukernelnor 0x08980000;" \
		"setenv swurootfsnor 0x09180000;" \
		"setenv swudtbnor 0x099A0000;" \
		"setenv bootargs console=${console} " \
		CONFIG_MTDPARTS_DEFAULT " " \
		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
		    ":${hostname}::off root=/dev/ram rw;" \
		"cp.l ${swurootfsnor} ${rootfsloadaddr} 0x200000;" \
		"cp.l ${swudtbnor} ${dtbloadaddr} 0x8000;" \
		"bootm ${swukernelnor} ${rootfsloadaddr} ${dtbloadaddr};\0" \
	"boot_tftp=" \
		"echo '#######################';" \
		"echo '# TFTP Boot           #';" \
		"echo '#######################';" \
		"if run download_kernel; then " \
		     "setenv bootargs console=${console} " \
		     "root=/dev/mmcblk0p2 rootwait;" \
		     "bootm ${kernel_addr} - ${fdt_addr};" \
		"fi\0" \
	"bootcmd=" \
		"if test -n ${recovery_status}; then " \
		     "run boot_recovery;" \
		"else " \
		     "if test ! -n ${boot_medium}; then " \
			  "run get_boot_medium;" \
			  "if test ${boot_medium} = sdcard; then " \
			      "run boot_sd;" \
			  "else " \
			      "run boot_nor;" \
			  "fi;" \
		     "else " \
			  "if test ${boot_medium} = tftp; then " \
			      "run boot_tftp;" \
			  "fi;" \
		     "fi;" \
		"fi\0" \
	"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
	"fdt_addr=0x18000000\0" \
	"bootdev=1\0" \
	"bootpart=1\0" \
	"kernel_addr=" __stringify(CONFIG_LOADADDR) "\0" \
	"netdev=eth0\0" \
	"load_addr=0x11000000\0" \
	"dtbloadaddr=0x12000000\0" \
	"uboot_file=u-boot.img\0" \
	"SPL_file=SPL\0" \
	"load_uboot=tftp ${load_addr} ${uboot_file}\0" \
	"nor_img_addr=0x11000000\0" \
	"nor_img_file=core-image-lwn-mccmon6.nor\0" \
	"emmc_img_file=core-image-lwn-mccmon6.ext4\0" \
	"nor_bank_start=" __stringify(CONFIG_SYS_FLASH_BASE) "\0" \
	"nor_img_size=0x02000000\0" \
	"factory_script_file=factory.scr\0" \
	"factory_load_script=" \
		"if test -e mmc ${mmcdev}:${mmcfactorypart} " \
		    "${factory_script_file}; then " \
		    "load mmc ${mmcdev}:${mmcfactorypart} " \
		     "${loadaddr} ${factory_script_file};" \
		"fi\0" \
	"factory_script=echo Running factory script from mmc${mmcdev} ...; " \
		"source ${loadaddr}\0" \
	"factory_flash_img="\
		"echo 'Flash mccmon6 with factory images'; " \
		"if run factory_load_script; then " \
			"run factory_script;" \
		"else " \
		    "echo No factory script: ${factory_script_file} found on " \
		    "device ${mmcdev};" \
		    "run factory_nor_img;" \
		    "run factory_eMMC_img;" \
		"fi\0" \
	"factory_eMMC_img="\
		"echo 'Update mccmon6 eMMC image'; " \
		"if load mmc ${mmcdev}:${mmcfactorypart} " \
		    "${loadaddr} ${emmc_img_file}; then " \
		    "setexpr fw_sz ${filesize} / 0x200;" \
		    "setexpr fw_sz ${fw_sz} + 1;" \
		    "mmc dev ${mmcfactorydev};" \
		    "mmc write ${loadaddr} 0x0 ${fw_sz};" \
		"fi\0" \
	"factory_nor_img="\
		"echo 'Update mccmon6 NOR image'; " \
		"if load mmc ${mmcdev}:${mmcfactorypart} " \
		    "${nor_img_addr} ${nor_img_file}; then " \
			"run nor_update;" \
		"fi\0" \
	"nor_update=" \
		    "protect off ${nor_bank_start} +${nor_img_size};" \
		    "erase ${nor_bank_start} +${nor_img_size};" \
		    "setexpr nor_img_size ${nor_img_size} / 4; " \
		    "cp.l ${nor_img_addr} ${nor_bank_start} ${nor_img_size}\0" \
	"tftp_nor_uboot="\
		"echo 'Update mccmon6 NOR U-BOOT via TFTP'; " \
		"setenv nor_img_file u-boot.img; " \
		"setenv nor_img_size 0x80000; " \
		"setenv nor_bank_start 0x08080000; " \
		"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
		    "run nor_update;" \
		"fi\0" \
	"tftp_nor_uImg="\
		"echo 'Update mccmon6 NOR uImage via TFTP'; " \
		"setenv nor_img_file uImage; " \
		"setenv nor_img_size 0x500000; " \
		"setenv nor_bank_start 0x08180000; " \
		"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
		    "run nor_update;" \
		"fi\0" \
	"tftp_nor_dtb="\
		"echo 'Update mccmon6 NOR DTB via TFTP'; " \
		"setenv nor_img_file imx6q-mccmon6.dtb; " \
		"setenv nor_img_size 0x20000; " \
		"setenv nor_bank_start 0x09980000; " \
		"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
		    "run nor_update;" \
		"fi\0" \
	"tftp_nor_img="\
		"echo 'Update mccmon6 NOR image via TFTP'; " \
		"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
		    "run nor_update;" \
		"fi\0" \
	"tftp_nor_SPL="\
		"if tftp ${load_addr} SPL_padded; then " \
		    "erase 0x08000000 +0x20000;" \
		    "cp.b ${load_addr} 0x08000000 0x20000;" \
		"fi;\0" \
	"tftp_sd_SPL="\
	    "if mmc dev 1; then "      \
		"if tftp ${load_addr} ${SPL_file}; then " \
		    "setexpr fw_sz ${filesize} / 0x200; " \
		    "setexpr fw_sz ${fw_sz} + 1; " \
		    "mmc write ${load_addr} 0x2 ${fw_sz};" \
		"fi;" \
	    "fi;\0" \
	"tftp_sd_uboot="\
	    "if mmc dev 1; then "      \
		"if run load_uboot; then " \
		    "setexpr fw_sz ${filesize} / 0x200; " \
		    "setexpr fw_sz ${fw_sz} + 1; " \
		    "mmc write ${load_addr} 0x8A ${fw_sz};" \
		"fi;" \
	    "fi;\0"

/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS		1
#define PHYS_SDRAM			MMDC0_ARB_BASE_ADDR

#define CONFIG_SYS_SDRAM_BASE		PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR	IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE	IRAM_SIZE

#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

/* Environment organization */
#define CONFIG_ENV_SIZE			(SZ_128K)

/* Envs are stored in NOR flash */
#define CONFIG_ENV_SECT_SIZE    (SZ_128K)
#define CONFIG_ENV_ADDR	(CONFIG_SYS_FLASH_BASE + 0x40000)

#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
#define CONFIG_ENV_ADDR_REDUND	(CONFIG_SYS_FLASH_BASE + 0x60000)
#define CONFIG_ENV_SIZE_REDUND	CONFIG_ENV_SIZE

#endif			       /* __CONFIG_H * */
Commit	Line	Data
11bd5e7b LM	1	/*
	2	* Copyright (C) 2016-2017
	3	* Lukasz Majewski, DENX Software Engineering, lukma@denx.de
	4	*
	5	* SPDX-License-Identifier: GPL-2.0+
	6	*/
	7
	8	#ifndef __CONFIG_H
	9	#define __CONFIG_H
	10
	11	#include <config_distro_defaults.h>
	12	#include "mx6_common.h"
	13
	14	#define CONFIG_SPL_LIBCOMMON_SUPPORT
	15	#include "imx6_spl.h"
	16
11bd5e7b LM	17	#define CONFIG_SYS_UBOOT_START CONFIG_SYS_TEXT_BASE
	18	#define CONFIG_SYS_UBOOT_BASE (CONFIG_SYS_FLASH_BASE + 0x80000)
	19	#define CONFIG_SPL_OS_BOOT
	20	#define CONFIG_SYS_OS_BASE (CONFIG_SYS_FLASH_BASE + 0x180000)
	21	#define CONFIG_SYS_FDT_BASE (CONFIG_SYS_FLASH_BASE + 0x1980000)
	22	#define CONFIG_SYS_FDT_SIZE (48 * SZ_1K)
	23	#define CONFIG_SYS_SPL_ARGS_ADDR 0x18000000
	24
	25	/*
	26	* Below defines are set but NOT really used since we by
	27	* design force U-Boot run when we boot in development
	28	* mode from SD card (SD2)
	29	*/
	30	#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR (0x800)
	31	#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS (0x80)
	32	#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR (0x1000)
	33	#define CONFIG_SPL_FS_LOAD_KERNEL_NAME "uImage"
	34	#define CONFIG_SPL_FS_LOAD_ARGS_NAME "imx6q-mccmon.dtb"
	35
	36	/* Size of malloc() pool */
	37	#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
	38
	39	#define CONFIG_BOARD_EARLY_INIT_F
	40	#define CONFIG_BOARD_LATE_INIT
	41
	42	#define CONFIG_MXC_UART
	43	#define CONFIG_MXC_UART_BASE UART1_BASE
	44
	45	#define CONFIG_SYS_MEMTEST_START 0x10000000
	46	#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 500 * SZ_1M)
	47
	48	#define CONFIG_MXC_SPI
	49	#define CONFIG_SF_DEFAULT_BUS 2
	50	#define CONFIG_SF_DEFAULT_CS 0
	51	#define CONFIG_SF_DEFAULT_SPEED 25000000
	52	#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
	53
	54	/* I2C Configs */
	55	#define CONFIG_SYS_I2C
	56	#define CONFIG_SYS_I2C_MXC
	57	#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
	58	#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
	59	#define CONFIG_SYS_I2C_SPEED 100000
	60
	61	/* MMC Configuration */
	62	#define CONFIG_SYS_FSL_USDHC_NUM 2
	63	#define CONFIG_SYS_FSL_ESDHC_ADDR 0
	64
11bd5e7b LM	65	/* NOR 16-bit mode */
	66	#define CONFIG_SYS_FLASH_BASE WEIM_ARB_BASE_ADDR
	67	#define CONFIG_SYS_FLASH_PROTECTION
	68	#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT
	69	#define CONFIG_SYS_FLASH_CFI /* Flash memory is CFI compliant */
	70	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE /* Use buffered writes*/
	71	#define CONFIG_SYS_FLASH_EMPTY_INFO
	72	#define CONFIG_FLASH_CFI_DRIVER /* Use drivers/cfi_flash.c */
	73	#define CONFIG_FLASH_VERIFY
	74
	75	/* NOR Flash MTD */
	76	#define CONFIG_FLASH_CFI_DRIVER
	77	#define CONFIG_FLASH_CFI_MTD
	78	#define CONFIG_SYS_MAX_FLASH_BANKS_DETECT 1
	79	#define CONFIG_SYS_FLASH_BANKS_LIST { (CONFIG_SYS_FLASH_BASE) }
	80	#define CONFIG_SYS_FLASH_BANKS_SIZES { (32 * SZ_1M) }
	81
	82	/* MTD support */
11bd5e7b LM	83	#define CONFIG_MTD_DEVICE
	84	#define CONFIG_MTD_PARTITIONS
	85
11bd5e7b	86	/* USB Configs */
11bd5e7b LM	87	#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
	88	#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI \| PORT_PTS_PTW)
	89	#define CONFIG_MXC_USB_FLAGS 0
	90
	91	/* Ethernet Configuration */
	92	#define CONFIG_FEC_MXC
	93	#define CONFIG_MII
	94	#define IMX_FEC_BASE ENET_BASE_ADDR
	95	#define CONFIG_FEC_XCV_TYPE RGMII
	96	#define CONFIG_ETHPRIME "FEC"
	97	#define CONFIG_FEC_MXC_PHYADDR 1
11bd5e7b LM	98
	99	#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
	100	#define CONFIG_EXTRA_ENV_SETTINGS \
cb11a28a	101	"console=ttymxc0,115200 quiet\0" \
11bd5e7b LM	102	"fdtfile=imx6q-mccmon6.dtb\0" \
	103	"fdt_high=0xffffffff\0" \
	104	"initrd_high=0xffffffff\0" \
	105	"boot_os=yes\0" \
	106	"download_kernel=" \
	107	"tftpboot ${kernel_addr} ${kernel_file};" \
	108	"tftpboot ${fdt_addr} ${fdtfile};\0" \
	109	"get_boot_medium=" \
	110	"setenv boot_medium nor;" \
	111	"setexpr.l _src_sbmr1 *0x020d8004;" \
	112	"setexpr _b_medium ${_src_sbmr1} '&' 0x00000040;" \
	113	"if test ${_b_medium} = 40; then " \
	114	"setenv boot_medium sdcard;" \
	115	"fi\0" \
	116	"kernel_file=uImage\0" \
	117	"load_kernel=" \
	118	"load mmc ${bootdev}:${bootpart} ${kernel_addr} uImage;" \
	119	"load mmc ${bootdev}:${bootpart} ${fdt_addr} ${fdtfile};\0" \
	120	"boot_sd=" \
	121	"echo '#######################';" \
	122	"echo '# Factory SDcard Boot #';" \
	123	"echo '#######################';" \
	124	"setenv mmcdev 1;" \
	125	"setenv mmcfactorydev 0;" \
	126	"setenv mmcfactorypart 1;" \
	127	"run factory_flash_img;\0" \
	128	"boot_nor=" \
	129	"setenv kernelnor 0x08180000;" \
	130	"setenv dtbnor 0x09980000;" \
cb11a28a	131	"setenv bootargs console=${console} " \
43ede0bc	132	CONFIG_MTDPARTS_DEFAULT " " \
11bd5e7b LM	133	"root=/dev/mmcblk1 rootfstype=ext4 rw rootwait noinitrd;" \
	134	"cp.l ${dtbnor} ${dtbloadaddr} 0x8000;" \
	135	"bootm ${kernelnor} - ${dtbloadaddr};\0" \
	136	"boot_recovery=" \
	137	"echo '#######################';" \
	138	"echo '# RECOVERY SWU Boot #';" \
	139	"echo '#######################';" \
	140	"setenv rootfsloadaddr 0x13000000;" \
	141	"setenv swukernelnor 0x08980000;" \
	142	"setenv swurootfsnor 0x09180000;" \
	143	"setenv swudtbnor 0x099A0000;" \
	144	"setenv bootargs console=${console} " \
43ede0bc	145	CONFIG_MTDPARTS_DEFAULT " " \
11bd5e7b LM	146	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
	147	":${hostname}::off root=/dev/ram rw;" \
	148	"cp.l ${swurootfsnor} ${rootfsloadaddr} 0x200000;" \
	149	"cp.l ${swudtbnor} ${dtbloadaddr} 0x8000;" \
	150	"bootm ${swukernelnor} ${rootfsloadaddr} ${dtbloadaddr};\0" \
	151	"boot_tftp=" \
	152	"echo '#######################';" \
	153	"echo '# TFTP Boot #';" \
	154	"echo '#######################';" \
	155	"if run download_kernel; then " \
	156	"setenv bootargs console=${console} " \
	157	"root=/dev/mmcblk0p2 rootwait;" \
	158	"bootm ${kernel_addr} - ${fdt_addr};" \
	159	"fi\0" \
	160	"bootcmd=" \
	161	"if test -n ${recovery_status}; then " \
	162	"run boot_recovery;" \
	163	"else " \
	164	"if test ! -n ${boot_medium}; then " \
	165	"run get_boot_medium;" \
	166	"if test ${boot_medium} = sdcard; then " \
	167	"run boot_sd;" \
	168	"else " \
	169	"run boot_nor;" \
	170	"fi;" \
	171	"else " \
	172	"if test ${boot_medium} = tftp; then " \
	173	"run boot_tftp;" \
	174	"fi;" \
	175	"fi;" \
	176	"fi\0" \
43ede0bc	177	"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
11bd5e7b LM	178	"fdt_addr=0x18000000\0" \
	179	"bootdev=1\0" \
	180	"bootpart=1\0" \
	181	"kernel_addr=" __stringify(CONFIG_LOADADDR) "\0" \
	182	"netdev=eth0\0" \
	183	"load_addr=0x11000000\0" \
	184	"dtbloadaddr=0x12000000\0" \
	185	"uboot_file=u-boot.img\0" \
	186	"SPL_file=SPL\0" \
	187	"load_uboot=tftp ${load_addr} ${uboot_file}\0" \
	188	"nor_img_addr=0x11000000\0" \
	189	"nor_img_file=core-image-lwn-mccmon6.nor\0" \
	190	"emmc_img_file=core-image-lwn-mccmon6.ext4\0" \
	191	"nor_bank_start=" __stringify(CONFIG_SYS_FLASH_BASE) "\0" \
	192	"nor_img_size=0x02000000\0" \
	193	"factory_script_file=factory.scr\0" \
	194	"factory_load_script=" \
	195	"if test -e mmc ${mmcdev}:${mmcfactorypart} " \
	196	"${factory_script_file}; then " \
	197	"load mmc ${mmcdev}:${mmcfactorypart} " \
	198	"${loadaddr} ${factory_script_file};" \
	199	"fi\0" \
	200	"factory_script=echo Running factory script from mmc${mmcdev} ...; " \
	201	"source ${loadaddr}\0" \
	202	"factory_flash_img="\
	203	"echo 'Flash mccmon6 with factory images'; " \
	204	"if run factory_load_script; then " \
	205	"run factory_script;" \
	206	"else " \
	207	"echo No factory script: ${factory_script_file} found on " \
	208	"device ${mmcdev};" \
	209	"run factory_nor_img;" \
	210	"run factory_eMMC_img;" \
	211	"fi\0" \
	212	"factory_eMMC_img="\
	213	"echo 'Update mccmon6 eMMC image'; " \
	214	"if load mmc ${mmcdev}:${mmcfactorypart} " \
	215	"${loadaddr} ${emmc_img_file}; then " \
	216	"setexpr fw_sz ${filesize} / 0x200;" \
	217	"setexpr fw_sz ${fw_sz} + 1;" \
	218	"mmc dev ${mmcfactorydev};" \
	219	"mmc write ${loadaddr} 0x0 ${fw_sz};" \
	220	"fi\0" \
	221	"factory_nor_img="\
	222	"echo 'Update mccmon6 NOR image'; " \
	223	"if load mmc ${mmcdev}:${mmcfactorypart} " \
	224	"${nor_img_addr} ${nor_img_file}; then " \
	225	"run nor_update;" \
	226	"fi\0" \
	227	"nor_update=" \
	228	"protect off ${nor_bank_start} +${nor_img_size};" \
	229	"erase ${nor_bank_start} +${nor_img_size};" \
	230	"setexpr nor_img_size ${nor_img_size} / 4; " \
	231	"cp.l ${nor_img_addr} ${nor_bank_start} ${nor_img_size}\0" \
	232	"tftp_nor_uboot="\
	233	"echo 'Update mccmon6 NOR U-BOOT via TFTP'; " \
	234	"setenv nor_img_file u-boot.img; " \
	235	"setenv nor_img_size 0x80000; " \
	236	"setenv nor_bank_start 0x08080000; " \
	237	"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
	238	"run nor_update;" \
	239	"fi\0" \
	240	"tftp_nor_uImg="\
	241	"echo 'Update mccmon6 NOR uImage via TFTP'; " \
242	"setenv nor_img_file uImage; " \
243	"setenv nor_img_size 0x500000; " \
244	"setenv nor_bank_start 0x08180000; " \
245	"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
246	"run nor_update;" \
247	"fi\0" \
5b8299e3 LM	248	"tftp_nor_dtb="\
	249	"echo 'Update mccmon6 NOR DTB via TFTP'; " \
	250	"setenv nor_img_file imx6q-mccmon6.dtb; " \
	251	"setenv nor_img_size 0x20000; " \
	252	"setenv nor_bank_start 0x09980000; " \
	253	"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
	254	"run nor_update;" \
	255	"fi\0" \
11bd5e7b LM	256	"tftp_nor_img="\
	257	"echo 'Update mccmon6 NOR image via TFTP'; " \
	258	"if tftpboot ${nor_img_addr} ${nor_img_file}; then " \
	259	"run nor_update;" \
	260	"fi\0" \
	261	"tftp_nor_SPL="\
	262	"if tftp ${load_addr} SPL_padded; then " \
	263	"erase 0x08000000 +0x20000;" \
	264	"cp.b ${load_addr} 0x08000000 0x20000;" \
	265	"fi;\0" \
	266	"tftp_sd_SPL="\
	267	"if mmc dev 1; then " \
	268	"if tftp ${load_addr} ${SPL_file}; then " \
	269	"setexpr fw_sz ${filesize} / 0x200; " \
	270	"setexpr fw_sz ${fw_sz} + 1; " \
	271	"mmc write ${load_addr} 0x2 ${fw_sz};" \
	272	"fi;" \
	273	"fi;\0" \
	274	"tftp_sd_uboot="\
	275	"if mmc dev 1; then " \
	276	"if run load_uboot; then " \
	277	"setexpr fw_sz ${filesize} / 0x200; " \
	278	"setexpr fw_sz ${fw_sz} + 1; " \
	279	"mmc write ${load_addr} 0x8A ${fw_sz};" \
	280	"fi;" \
	281	"fi;\0"
	282
	283	/* Physical Memory Map */
	284	#define CONFIG_NR_DRAM_BANKS 1
	285	#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
	286
	287	#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
	288	#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
	289	#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
	290
	291	#define CONFIG_SYS_INIT_SP_OFFSET \
	292	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	293	#define CONFIG_SYS_INIT_SP_ADDR \
	294	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
	295
	296	/* Environment organization */
	297	#define CONFIG_ENV_SIZE (SZ_128K)
	298
	299	/* Envs are stored in NOR flash */
11bd5e7b LM	300	#define CONFIG_ENV_SECT_SIZE (SZ_128K)
	301	#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x40000)
	302
	303	#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
	304	#define CONFIG_ENV_ADDR_REDUND (CONFIG_SYS_FLASH_BASE + 0x60000)
	305	#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
	306
	307	#endif /* __CONFIG_H * */