]>
Commit | Line | Data |
---|---|---|
c11da194 NG |
1 | /* |
2 | * (C) Copyright 2008 | |
3 | * Niklaus Giger, Netstal Maschinen AG, niklaus.giger@netstal.com | |
4 | * adapted from amcc-common.h by | |
5 | * (C) Copyright 2008 | |
6 | * * Stefan Roese, DENX Software Engineering, sr@denx.de. | |
7 | * | |
8 | * Common configuration options for all Netstal boards | |
9 | * | |
10 | * This program is free software; you can redistribute it and/or | |
11 | * modify it under the terms of the GNU General Public License as | |
12 | * published by the Free Software Foundation; either version 2 of | |
13 | * the License, or (at your option) any later version. | |
14 | * | |
15 | * This program is distributed in the hope that it will be useful, | |
16 | * but WITHOUT ANY WARRANTY; without even the implied warranty of | |
17 | * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |
18 | * GNU General Public License for more details. | |
19 | * | |
20 | * You should have received a copy of the GNU General Public License | |
21 | * along with this program; if not, write to the Free Software | |
22 | * Foundation, Inc., 59 Temple Place, Suite 330, Boston, | |
23 | * MA 02111-1307 USA | |
24 | */ | |
25 | ||
26 | #ifndef __NETSTAL_COMMON_H | |
27 | #define __NETSTAL_COMMON_H | |
28 | ||
29 | #define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */ | |
30 | #define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* Start of U-Boot */ | |
31 | #define CONFIG_SYS_MONITOR_LEN (320 * 1024) /* Reserve 320 kB for Monitor */ | |
32 | #define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserve 256 kB for malloc() */ | |
33 | ||
34 | /* | |
35 | * UART | |
36 | */ | |
37 | #define CONFIG_SERIAL_MULTI | |
38 | #define CONFIG_SYS_BAUDRATE_TABLE \ | |
39 | {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400} | |
40 | ||
41 | /* | |
42 | * I2C | |
43 | */ | |
44 | #define CONFIG_HARD_I2C 1 /* I2C with hardware support */ | |
45 | #define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */ | |
46 | #define CONFIG_SYS_I2C_SLAVE 0x7F | |
47 | ||
48 | /* This is the 7bit address of the device, not including P. */ | |
49 | #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 | |
50 | #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 | |
51 | ||
52 | /* The EEPROM can do 16byte ( 1 << 4 ) page writes. */ | |
53 | #define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07 | |
54 | #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 | |
55 | #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 | |
56 | #define CONFIG_SYS_EEPROM_PAGE_WRITE_ENABLE | |
57 | ||
58 | /* | |
59 | * Ethernet/EMAC/PHY | |
60 | */ | |
96e21f86 | 61 | #define CONFIG_PPC4xx_EMAC |
c11da194 NG |
62 | #define CONFIG_MII /* MII PHY management */ |
63 | #define CONFIG_PHY_ADDR 1 /* PHY address */ | |
64 | #if defined(CONFIG_440) | |
65 | #define CONFIG_NET_MULTI 1 | |
66 | #define CONFIG_NETCONSOLE /* include NetConsole support */ | |
67 | #define CONFIG_SYS_RX_ETH_BUFFER 32 /* number of eth rx buffers */ | |
68 | #else | |
69 | #define CONFIG_SYS_RX_ETH_BUFFER 16 /* number of eth rx buffers */ | |
70 | #endif | |
71 | #define CONFIG_HAS_ETH0 | |
72 | ||
73 | /* | |
74 | * Commands | |
75 | */ | |
76 | #include <config_cmd_default.h> | |
77 | ||
78 | #define CONFIG_CMD_ASKENV | |
79 | #if defined(CONFIG_440) | |
80 | #define CONFIG_CMD_CACHE | |
81 | #endif | |
82 | #define CONFIG_CMD_DHCP | |
83 | #define CONFIG_CMD_DIAG | |
84 | #define CONFIG_CMD_EEPROM | |
85 | #define CONFIG_CMD_ELF | |
86 | #define CONFIG_CMD_I2C | |
87 | #define CONFIG_CMD_IRQ | |
88 | #define CONFIG_CMD_MII | |
89 | #define CONFIG_CMD_NET | |
90 | #define CONFIG_CMD_NFS | |
91 | #define CONFIG_CMD_PING | |
92 | #define CONFIG_CMD_REGINFO | |
93 | #define CONFIG_BOOT_RETRY_TIME 30 | |
94 | #define CONFIG_RESET_TO_RETRY | |
95 | /* | |
96 | * Miscellaneous configurable options | |
97 | */ | |
98 | #define CONFIG_BOOTDELAY 1 /* autoboot after 1 second */ | |
99 | #define CONFIG_SYS_LONGHELP /* undef to save memory */ | |
100 | #define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */ | |
101 | #if defined(CONFIG_CMD_KGDB) | |
102 | #define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */ | |
103 | #else | |
104 | #define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */ | |
105 | #endif | |
106 | #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) | |
107 | #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ | |
108 | #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */ | |
109 | ||
110 | #define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */ | |
111 | #define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */ | |
112 | ||
113 | #define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */ | |
114 | #define CONFIG_SYS_EXTBDINFO /* To use extended board_into (bd_t) */ | |
115 | ||
116 | #define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */ | |
117 | ||
118 | #define CONFIG_CMDLINE_EDITING /* add command line history */ | |
119 | #define CONFIG_AUTO_COMPLETE /* add autocompletion support */ | |
120 | #define CONFIG_LOOPW /* enable loopw command */ | |
121 | #define CONFIG_MX_CYCLIC /* enable mdc/mwc commands */ | |
122 | #define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */ | |
123 | #define CONFIG_VERSION_VARIABLE /* include version env variable */ | |
124 | #define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup*/ | |
125 | ||
126 | #define CONFIG_SYS_HUSH_PARSER /* Use the HUSH parser */ | |
127 | #ifdef CONFIG_SYS_HUSH_PARSER | |
128 | #define CONFIG_SYS_PROMPT_HUSH_PS2 "> " | |
129 | #endif | |
130 | ||
131 | #define CONFIG_LOADS_ECHO /* echo on for serial download */ | |
132 | #define CONFIG_SYS_LOADS_BAUD_CHANGE /* allow baudrate change */ | |
133 | ||
134 | /* | |
135 | * BOOTP options | |
136 | */ | |
137 | #define CONFIG_BOOTP_BOOTFILESIZE | |
138 | #define CONFIG_BOOTP_BOOTPATH | |
139 | #define CONFIG_BOOTP_GATEWAY | |
140 | #define CONFIG_BOOTP_HOSTNAME | |
141 | #define CONFIG_BOOTP_SUBNETMASK | |
142 | ||
143 | /* | |
144 | * For booting Linux, the board info and command line data | |
145 | * have to be in the first 8 MB of memory, since this is | |
146 | * the maximum mapped by the Linux kernel during initialization. | |
147 | */ | |
148 | #define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */ | |
149 | ||
150 | /* | |
151 | * Internal Definitions | |
152 | */ | |
153 | #if defined(CONFIG_CMD_KGDB) | |
154 | #define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port*/ | |
155 | #define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */ | |
156 | #endif | |
157 | ||
158 | /* | |
159 | * Pass open firmware flat tree | |
160 | */ | |
161 | #define CONFIG_OF_LIBFDT | |
162 | #define CONFIG_OF_BOARD_SETUP | |
163 | ||
164 | /* | |
165 | * Booting and default environment | |
166 | */ | |
167 | #define CONFIG_PREBOOT "echo;" \ | |
168 | "echo Type \"run net_nfs\" to mount root filesystem over NFS;" \ | |
169 | "echo" | |
170 | #define CONFIG_BOOTCOMMAND "run vx" | |
171 | ||
172 | /* | |
173 | * Only very few boards have default console not on ttyS0 (like Taishan) | |
174 | */ | |
175 | #if !defined(CONFIG_USE_TTY) | |
176 | #define CONFIG_USE_TTY ttyS0 | |
177 | #endif | |
178 | ||
179 | /* | |
180 | * Only some 4xx PPC's are equipped with an FPU | |
181 | */ | |
182 | #if defined(CONFIG_440EP) || defined(CONFIG_440EPX) || \ | |
183 | defined(CONFIG_460EX) || defined(CONFIG_460GT) | |
184 | #define CONFIG_NETSTAL_DEF_ENV_ROOTPATH "rootpath=/opt/eldk/ppc_4xxFP\0" | |
185 | #else | |
186 | #define CONFIG_NETSTAL_DEF_ENV_ROOTPATH "rootpath=/opt/eldk/ppc_4xx\0" | |
187 | #endif | |
188 | ||
189 | /* | |
190 | * Only some boards need to extend the bootargs by some additional | |
191 | * parameters (like Makalu) | |
192 | */ | |
193 | #if !defined(CONFIG_ADDMISC) | |
194 | #define CONFIG_ADDMISC "addmisc=setenv bootargs ${bootargs}\0" | |
195 | #endif | |
196 | ||
197 | #define xstr(s) str(s) | |
198 | #define str(s) #s | |
199 | ||
200 | /* Setup some values for the default environment variables */ | |
201 | #define CONFIG_SERVERIP 172.25.1.1 | |
202 | #define CONFIG_ETHADDR 00:60:13:00:00:00 /* Netstal Machines AG MAC */ | |
203 | #define CONFIG_OVERWRITE_ETHADDR_ONCE | |
204 | ||
b03150b5 NG |
205 | #define CONFIG_SYS_TFTP_LOADADDR 0x01000000 |
206 | #define CONFIG_SYS_VXWORKS_ADD_PARAMS "u=dpu pw=netstal8752" | |
207 | #define CONFIG_SYS_VXWORKS_SERVERNAME "c" | |
c11da194 NG |
208 | /* |
209 | * General common environment variables shared by all boards produced by Netstal Maschinen | |
210 | */ | |
211 | #define CONFIG_NETSTAL_DEF_ENV \ | |
212 | "netdev=eth0\0" \ | |
213 | "nfsargs=setenv bootargs root=/dev/nfs rw " \ | |
214 | "nfsroot=${serverip}:${rootpath}\0" \ | |
215 | "ramargs=setenv bootargs root=/dev/ram rw\0" \ | |
216 | "addip=setenv bootargs ${bootargs} " \ | |
217 | "ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \ | |
218 | ":${hostname}:${netdev}:off panic=1\0" \ | |
219 | "addtty=setenv bootargs ${bootargs}" \ | |
220 | " console=" xstr(CONFIG_USE_TTY) ",${baudrate}\0" \ | |
221 | CONFIG_ADDMISC \ | |
222 | "initrd_high=30000000\0" \ | |
223 | "kernel_addr_r=400000\0" \ | |
224 | "fdt_addr_r=800000\0" \ | |
225 | "hostname=" xstr(CONFIG_HOSTNAME) "\0" \ | |
226 | "bootfile=" xstr(CONFIG_HOSTNAME) "/uImage\0" \ | |
b03150b5 NG |
227 | "uload=tftp " xstr(CONFIG_SYS_TFTP_LOADADDR) " " \ |
228 | xstr(CONFIG_HOSTNAME) "/u-boot.bin\0" \ | |
229 | "vx_rom=" xstr(CONFIG_HOSTNAME) "/" \ | |
230 | xstr(CONFIG_HOSTNAME) "_vx_rom\0" \ | |
231 | "update=protect off " xstr(CONFIG_SYS_MONITOR_BASE) " FFFFFFFF;"\ | |
232 | "era " xstr(CONFIG_SYS_MONITOR_BASE) " FFFFFFFF;" \ | |
233 | "cp.b ${fileaddr} "xstr(CONFIG_SYS_MONITOR_BASE) \ | |
234 | " ${filesize}; setenv filesize\0" \ | |
235 | "upd=run uload update\0" \ | |
236 | "vx=setenv bootfile ${vx_rom}; tftp " \ | |
237 | xstr(CONFIG_SYS_TFTP_LOADADDR) "; bootvx\0" \ | |
c11da194 NG |
238 | CONFIG_NETSTAL_DEF_ENV_ROOTPATH |
239 | ||
240 | /* | |
241 | * Default environment for arch/powerpc booting | |
242 | * for boards that are ported to arch/powerpc | |
243 | */ | |
244 | #define CONFIG_NETSTAL_DEF_ENV_POWERPC \ | |
245 | "flash_self=run ramargs addip addtty addmisc;" \ | |
246 | "bootm ${kernel_addr} ${ramdisk_addr} ${fdt_addr}\0" \ | |
247 | "flash_nfs=run nfsargs addip addtty addmisc;" \ | |
248 | "bootm ${kernel_addr} - ${fdt_addr}\0" \ | |
249 | "net_nfs=tftp ${kernel_addr_r} ${bootfile}; " \ | |
250 | "tftp ${fdt_addr_r} ${fdt_file}; " \ | |
251 | "run nfsargs addip addtty addmisc;" \ | |
252 | "bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \ | |
253 | "fdt_file=" xstr(CONFIG_HOSTNAME) "/" xstr(CONFIG_HOSTNAME) ".dtb\0" | |
254 | ||
255 | #endif /* __NETSTAL_COMMON_H */ |