[people/ms/u-boot.git] / include / configs / omap3_beagle.h

/*
 * (C) Copyright 2006-2008
 * Texas Instruments.
 * Richard Woodruff <r-woodruff2@ti.com>
 * Syed Mohammed Khasim <x0khasim@ti.com>
 *
 * Configuration settings for the TI OMAP3530 Beagle board.
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

#define CONFIG_NR_DRAM_BANKS	2	/* CS1 may or may not be populated */

/*
 * 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
 * 64 bytes before this address should be set aside for u-boot.img's
 * header. That is 0x800FFFC0--0x80100000 should not be used for any
 * other needs.  We use this rather than the inherited defines from
 * ti_armv7_common.h for backwards compatibility.
 */
#define CONFIG_SYS_TEXT_BASE		0x80100000
#define CONFIG_SPL_BSS_START_ADDR	0x80000000
#define CONFIG_SPL_BSS_MAX_SIZE		(512 << 10)	/* 512 KB */
#define CONFIG_SYS_SPL_MALLOC_START	0x80208000
#define CONFIG_SYS_SPL_MALLOC_SIZE	0x100000

#include <configs/ti_omap3_common.h>

#define CONFIG_MISC_INIT_R

#define CONFIG_REVISION_TAG		1
#define CONFIG_ENV_OVERWRITE

/* Status LED */
#define CONFIG_STATUS_LED		1
#define CONFIG_BOARD_SPECIFIC_LED	1
#define STATUS_LED_BIT			0x01
#define STATUS_LED_STATE		STATUS_LED_ON
#define STATUS_LED_PERIOD		(CONFIG_SYS_HZ / 2)
#define STATUS_LED_BIT1			0x02
#define STATUS_LED_STATE1		STATUS_LED_ON
#define STATUS_LED_PERIOD1		(CONFIG_SYS_HZ / 2)
#define STATUS_LED_BOOT			STATUS_LED_BIT
#define STATUS_LED_GREEN		STATUS_LED_BIT1

/* Enable Multi Bus support for I2C */
#define CONFIG_I2C_MULTI_BUS		1

/* Probe all devices */
#define CONFIG_SYS_I2C_NOPROBES		{{0x0, 0x0}}

/* USB */
#define CONFIG_USB_MUSB_OMAP2PLUS
#define CONFIG_USB_MUSB_PIO_ONLY
#define CONFIG_TWL4030_USB		1
#define CONFIG_USB_ETHER
#define CONFIG_USB_ETHER_RNDIS
#define CONFIG_USB_FUNCTION_FASTBOOT
#define CONFIG_CMD_FASTBOOT
#define CONFIG_ANDROID_BOOT_IMAGE
#define CONFIG_FASTBOOT_BUF_ADDR	CONFIG_SYS_LOAD_ADDR
#define CONFIG_FASTBOOT_BUF_SIZE	0x07000000

/* USB EHCI */
#define CONFIG_USB_EHCI

#define CONFIG_USB_EHCI_OMAP
#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO	147

#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_USB_ETHER_MCS7830
#define CONFIG_USB_ETHER_SMSC95XX

/* GPIO banks */
#define CONFIG_OMAP3_GPIO_5		/* GPIO128..159 is in GPIO bank 5 */
#define CONFIG_OMAP3_GPIO_6		/* GPIO160..191 is in GPIO bank 6 */

/* commands to include */

#define MTDIDS_DEFAULT			"nand0=nand"
#define MTDPARTS_DEFAULT		"mtdparts=nand:512k(x-loader),"\
					"1920k(u-boot),128k(u-boot-env),"\
					"4m(kernel),-(fs)"

#define CONFIG_CMD_NAND		/* NAND support			*/
#define CONFIG_CMD_LED		/* LED support			*/

#define CONFIG_VIDEO_OMAP3	/* DSS Support			*/

/*
 * TWL4030
 */
#define CONFIG_TWL4030_LED		1

/*
 * Board NAND Info.
 */
#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_SYS_MAX_NAND_DEVICE	1		/* Max number of NAND */
							/* devices */

#define BOOT_TARGET_DEVICES(func) \
	func(MMC, mmc, 0)

#define CONFIG_BOOTCOMMAND \
	"run findfdt; " \
	"run distro_bootcmd; " \
	"mmc dev ${mmcdev}; if mmc rescan; then " \
		"if run userbutton; then " \
			"setenv bootenv uEnv.txt;" \
		"else " \
			"setenv bootenv user.txt;" \
		"fi;" \
		"echo SD/MMC found on device ${mmcdev};" \
		"if run loadbootenv; then " \
			"echo Loaded environment from ${bootenv};" \
			"run importbootenv;" \
		"fi;" \
		"if test -n $uenvcmd; then " \
			"echo Running uenvcmd ...;" \
			"run uenvcmd;" \
		"fi;" \
		"if run loadbootscript; then " \
			"run bootscript; " \
		"else " \
			"if run loadimage; then " \
				"run mmcboot;" \
			"fi;" \
		"fi; " \
	"fi;" \
	"run nandboot;" \
	"setenv bootfile zImage;" \
	"if run loadimage; then " \
		"run loadfdt;" \
		"run mmcbootz; " \
	"fi; " \

#include <config_distro_bootcmd.h>

#define CONFIG_EXTRA_ENV_SETTINGS \
	"loadaddr=0x80200000\0" \
	"kernel_addr_r=0x80200000\0" \
	"rdaddr=0x81000000\0" \
	"initrd_addr_r=0x81000000\0" \
	"fdt_high=0xffffffff\0" \
	"fdtaddr=0x80f80000\0" \
	"fdt_addr_r=0x80f80000\0" \
	"usbtty=cdc_acm\0" \
	"bootfile=uImage\0" \
	"ramdisk=ramdisk.gz\0" \
	"bootdir=/boot\0" \
	"bootpart=0:2\0" \
	"console=ttyO2,115200n8\0" \
	"mpurate=auto\0" \
	"buddy=none\0" \
	"optargs=\0" \
	"camera=none\0" \
	"vram=12M\0" \
	"dvimode=640x480MR-16@60\0" \
	"defaultdisplay=dvi\0" \
	"mmcdev=0\0" \
	"mmcroot=/dev/mmcblk0p2 rw\0" \
	"mmcrootfstype=ext3 rootwait\0" \
	"nandroot=ubi0:rootfs ubi.mtd=4\0" \
	"nandrootfstype=ubifs\0" \
	"ramroot=/dev/ram0 rw ramdisk_size=65536 initrd=0x81000000,64M\0" \
	"ramrootfstype=ext2\0" \
	"mmcargs=setenv bootargs console=${console} " \
		"${optargs} " \
		"mpurate=${mpurate} " \
		"buddy=${buddy} "\
		"camera=${camera} "\
		"vram=${vram} " \
		"omapfb.mode=dvi:${dvimode} " \
		"omapdss.def_disp=${defaultdisplay} " \
		"root=${mmcroot} " \
		"rootfstype=${mmcrootfstype}\0" \
	"nandargs=setenv bootargs console=${console} " \
		"${optargs} " \
		"mpurate=${mpurate} " \
		"buddy=${buddy} "\
		"camera=${camera} "\
		"vram=${vram} " \
		"omapfb.mode=dvi:${dvimode} " \
		"omapdss.def_disp=${defaultdisplay} " \
		"root=${nandroot} " \
		"rootfstype=${nandrootfstype}\0" \
	"findfdt=" \
		"if test $beaglerev = AxBx; then " \
			"setenv fdtfile omap3-beagle.dtb; fi; " \
		"if test $beaglerev = Cx; then " \
			"setenv fdtfile omap3-beagle.dtb; fi; " \
		"if test $beaglerev = C4; then " \
			"setenv fdtfile omap3-beagle.dtb; fi; " \
		"if test $beaglerev = xMAB; then " \
			"setenv fdtfile omap3-beagle-xm-ab.dtb; fi; " \
		"if test $beaglerev = xMC; then " \
			"setenv fdtfile omap3-beagle-xm.dtb; fi; " \
		"if test $fdtfile = undefined; then " \
			"echo WARNING: Could not determine device tree to use; fi; \0" \
	"validatefdt=" \
		"if test $beaglerev = xMAB; then " \
			"if test ! -e mmc ${bootpart} ${bootdir}/${fdtfile}; then " \
				"setenv fdtfile omap3-beagle-xm.dtb; " \
			"fi; " \
		"fi; \0" \
	"bootenv=uEnv.txt\0" \
	"loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
	"importbootenv=echo Importing environment from mmc ...; " \
		"env import -t -r $loadaddr $filesize\0" \
	"ramargs=setenv bootargs console=${console} " \
		"${optargs} " \
		"mpurate=${mpurate} " \
		"buddy=${buddy} "\
		"vram=${vram} " \
		"omapfb.mode=dvi:${dvimode} " \
		"omapdss.def_disp=${defaultdisplay} " \
		"root=${ramroot} " \
		"rootfstype=${ramrootfstype}\0" \
	"loadramdisk=load mmc ${bootpart} ${rdaddr} ${bootdir}/${ramdisk}\0" \
	"loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
	"loadbootscript=load mmc ${mmcdev} ${loadaddr} boot.scr\0" \
	"bootscript=echo Running bootscript from mmc${mmcdev} ...; " \
		"source ${loadaddr}\0" \
	"loadfdt=run validatefdt; load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
	"mmcboot=echo Booting from mmc ...; " \
		"run mmcargs; " \
		"bootm ${loadaddr}\0" \
	"mmcbootz=echo Booting with DT from mmc${mmcdev} ...; " \
		"run mmcargs; " \
		"bootz ${loadaddr} - ${fdtaddr}\0" \
	"nandboot=echo Booting from nand ...; " \
		"run nandargs; " \
		"nand read ${loadaddr} 280000 400000; " \
		"bootm ${loadaddr}\0" \
	"ramboot=echo Booting from ramdisk ...; " \
		"run ramargs; " \
		"bootm ${loadaddr}\0" \
	"userbutton=if gpio input 173; then run userbutton_xm; " \
		"else run userbutton_nonxm; fi;\0" \
	"userbutton_xm=gpio input 4;\0" \
	"userbutton_nonxm=gpio input 7;\0" \
	BOOTENV

/*
 * OMAP3 has 12 GP timers, they can be driven by the system clock
 * (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
 * This rate is divided by a local divisor.
 */
#define CONFIG_SYS_PTV			2       /* Divisor: 2^(PTV+1) => 8 */

/*-----------------------------------------------------------------------
 * FLASH and environment organization
 */

/* **** PISMO SUPPORT *** */
#if defined(CONFIG_CMD_NAND)
#define CONFIG_SYS_FLASH_BASE		NAND_BASE
#endif

/* Monitor at start of flash */
#define CONFIG_SYS_MONITOR_BASE		CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_ONENAND_BASE		ONENAND_MAP

#define CONFIG_ENV_IS_IN_NAND		1
#define CONFIG_ENV_SIZE			(128 << 10)	/* 128 KiB */
#define ONENAND_ENV_OFFSET		0x260000 /* environment starts here */
#define SMNAND_ENV_OFFSET		0x260000 /* environment starts here */

#define CONFIG_SYS_ENV_SECT_SIZE	(128 << 10)	/* 128 KiB */
#define CONFIG_ENV_OFFSET		SMNAND_ENV_OFFSET
#define CONFIG_ENV_ADDR			SMNAND_ENV_OFFSET

#define CONFIG_OMAP3_SPI

/* Defines for SPL */
#define CONFIG_SPL_OMAP3_ID_NAND

/* NAND boot config */
#define CONFIG_SYS_NAND_BUSWIDTH_16BIT
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT	64
#define CONFIG_SYS_NAND_PAGE_SIZE	2048
#define CONFIG_SYS_NAND_OOBSIZE		64
#define CONFIG_SYS_NAND_BLOCK_SIZE	(128*1024)
#define CONFIG_SYS_NAND_BAD_BLOCK_POS	0
#define CONFIG_SYS_NAND_ECCPOS		{2, 3, 4, 5, 6, 7, 8, 9,\
						10, 11, 12, 13}
#define CONFIG_SYS_NAND_ECCSIZE		512
#define CONFIG_SYS_NAND_ECCBYTES	3
#define CONFIG_NAND_OMAP_ECCSCHEME	OMAP_ECC_HAM1_CODE_HW
#define CONFIG_SYS_NAND_U_BOOT_OFFS	0x80000
/* NAND: SPL falcon mode configs */
#ifdef CONFIG_SPL_OS_BOOT
#define CONFIG_CMD_SPL_NAND_OFS		0x240000
#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS	0x280000
#define CONFIG_CMD_SPL_WRITE_SIZE	0x2000
#endif

#endif /* __CONFIG_H */
Commit	Line	Data
f904cdbb DB	1	/*
	2	* (C) Copyright 2006-2008
	3	* Texas Instruments.
	4	* Richard Woodruff <r-woodruff2@ti.com>
	5	* Syed Mohammed Khasim <x0khasim@ti.com>
	6	*
	7	* Configuration settings for the TI OMAP3530 Beagle board.
	8	*
3765b3e7	9	* SPDX-License-Identifier: GPL-2.0+
f904cdbb DB	10	*/
	11
	12	#ifndef __CONFIG_H
	13	#define __CONFIG_H
f904cdbb	14
df4dbb5d TR	15	#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
df4dbb5d TR	16
f904cdbb	17	/*
df4dbb5d TR	18	* 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
	19	* 64 bytes before this address should be set aside for u-boot.img's
	20	* header. That is 0x800FFFC0--0x80100000 should not be used for any
	21	* other needs. We use this rather than the inherited defines from
	22	* ti_armv7_common.h for backwards compatibility.
f904cdbb	23	*/
df4dbb5d TR	24	#define CONFIG_SYS_TEXT_BASE 0x80100000
	25	#define CONFIG_SPL_BSS_START_ADDR 0x80000000
	26	#define CONFIG_SPL_BSS_MAX_SIZE (512 << 10) /* 512 KB */
	27	#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
	28	#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
cae377b5	29
df4dbb5d	30	#include <configs/ti_omap3_common.h>
f904cdbb	31
f904cdbb DB	32	#define CONFIG_MISC_INIT_R
f904cdbb DB	33
f904cdbb	34	#define CONFIG_REVISION_TAG 1
f904cdbb	35	#define CONFIG_ENV_OVERWRITE
f904cdbb	36
70d8c944 JK	37	/* Status LED */
	38	#define CONFIG_STATUS_LED 1
	39	#define CONFIG_BOARD_SPECIFIC_LED 1
	40	#define STATUS_LED_BIT 0x01
	41	#define STATUS_LED_STATE STATUS_LED_ON
	42	#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2)
	43	#define STATUS_LED_BIT1 0x02
	44	#define STATUS_LED_STATE1 STATUS_LED_ON
	45	#define STATUS_LED_PERIOD1 (CONFIG_SYS_HZ / 2)
	46	#define STATUS_LED_BOOT STATUS_LED_BIT
	47	#define STATUS_LED_GREEN STATUS_LED_BIT1
	48
f74fc4ae JK	49	/* Enable Multi Bus support for I2C */
	50	#define CONFIG_I2C_MULTI_BUS 1
	51
	52	/* Probe all devices */
8c4e0ca6	53	#define CONFIG_SYS_I2C_NOPROBES {{0x0, 0x0}}
f74fc4ae	54
25374bfb	55	/* USB */
c2af345e	56	#define CONFIG_USB_MUSB_OMAP2PLUS
95de1e2f	57	#define CONFIG_USB_MUSB_PIO_ONLY
25374bfb	58	#define CONFIG_TWL4030_USB 1
c642b151 IY	59	#define CONFIG_USB_ETHER
c642b151 IY	60	#define CONFIG_USB_ETHER_RNDIS
17da3c0c	61	#define CONFIG_USB_FUNCTION_FASTBOOT
dd5b68fb RH	62	#define CONFIG_CMD_FASTBOOT
dd5b68fb RH	63	#define CONFIG_ANDROID_BOOT_IMAGE
a588d99a PK	64	#define CONFIG_FASTBOOT_BUF_ADDR CONFIG_SYS_LOAD_ADDR
a588d99a PK	65	#define CONFIG_FASTBOOT_BUF_SIZE 0x07000000
25374bfb	66
d90859a6	67	/* USB EHCI */
d90859a6	68	#define CONFIG_USB_EHCI
928c4bdf	69
29321c05	70	#define CONFIG_USB_EHCI_OMAP
29321c05 IY	71	#define CONFIG_OMAP_EHCI_PHY1_RESET_GPIO 147
29321c05 IY	72
d90859a6	73	#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
2162439a	74	#define CONFIG_USB_HOST_ETHER
54b62d59	75	#define CONFIG_USB_ETHER_ASIX
a743415f	76	#define CONFIG_USB_ETHER_MCS7830
eddf6d28	77	#define CONFIG_USB_ETHER_SMSC95XX
2162439a	78
ce23b18b SR	79	/* GPIO banks */
	80	#define CONFIG_OMAP3_GPIO_5 /* GPIO128..159 is in GPIO bank 5 */
	81	#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */
d90859a6	82
f904cdbb	83	/* commands to include */
df4dbb5d	84
917cfc70 NM	85	#define MTDIDS_DEFAULT "nand0=nand"
	86	#define MTDPARTS_DEFAULT "mtdparts=nand:512k(x-loader),"\
	87	"1920k(u-boot),128k(u-boot-env),"\
	88	"4m(kernel),-(fs)"
f904cdbb	89
f904cdbb	90	#define CONFIG_CMD_NAND /* NAND support */
70d8c944	91	#define CONFIG_CMD_LED /* LED support */
f904cdbb	92
25a4d017	93	#define CONFIG_VIDEO_OMAP3 /* DSS Support */
f904cdbb	94
2c155130 TR	95	/*
	96	* TWL4030
	97	*/
2c155130 TR	98	#define CONFIG_TWL4030_LED 1
2c155130 TR	99
f904cdbb DB	100	/*
	101	* Board NAND Info.
	102	*/
	103	#define CONFIG_NAND_OMAP_GPMC
f904cdbb DB	104	#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND */
f904cdbb DB	105	/* devices */
f904cdbb	106
c721fd6e GG	107	#define BOOT_TARGET_DEVICES(func) \
	108	func(MMC, mmc, 0)
	109
	110	#define CONFIG_BOOTCOMMAND \
	111	"run findfdt; " \
	112	"run distro_bootcmd; " \
	113	"mmc dev ${mmcdev}; if mmc rescan; then " \
	114	"if run userbutton; then " \
	115	"setenv bootenv uEnv.txt;" \
	116	"else " \
	117	"setenv bootenv user.txt;" \
	118	"fi;" \
	119	"echo SD/MMC found on device ${mmcdev};" \
	120	"if run loadbootenv; then " \
	121	"echo Loaded environment from ${bootenv};" \
	122	"run importbootenv;" \
	123	"fi;" \
	124	"if test -n $uenvcmd; then " \
	125	"echo Running uenvcmd ...;" \
	126	"run uenvcmd;" \
	127	"fi;" \
	128	"if run loadbootscript; then " \
	129	"run bootscript; " \
	130	"else " \
	131	"if run loadimage; then " \
	132	"run mmcboot;" \
	133	"fi;" \
	134	"fi; " \
	135	"fi;" \
	136	"run nandboot;" \
	137	"setenv bootfile zImage;" \
	138	"if run loadimage; then " \
	139	"run loadfdt;" \
	140	"run mmcbootz; " \
	141	"fi; " \
	142
	143	#include <config_distro_bootcmd.h>
	144
f904cdbb	145	#define CONFIG_EXTRA_ENV_SETTINGS \
f4b36ea9	146	"loadaddr=0x80200000\0" \
c721fd6e	147	"kernel_addr_r=0x80200000\0" \
f4b36ea9	148	"rdaddr=0x81000000\0" \
c721fd6e	149	"initrd_addr_r=0x81000000\0" \
2ade496f NM	150	"fdt_high=0xffffffff\0" \
2ade496f NM	151	"fdtaddr=0x80f80000\0" \
c721fd6e	152	"fdt_addr_r=0x80f80000\0" \
25374bfb	153	"usbtty=cdc_acm\0" \
a33e3c79	154	"bootfile=uImage\0" \
102ce9ea NM	155	"ramdisk=ramdisk.gz\0" \
	156	"bootdir=/boot\0" \
	157	"bootpart=0:2\0" \
27b8c8f2	158	"console=ttyO2,115200n8\0" \
f6e593bb	159	"mpurate=auto\0" \
847b83d0	160	"buddy=none\0" \
c522eac4 JK	161	"optargs=\0" \
c522eac4 JK	162	"camera=none\0" \
13d2cb98	163	"vram=12M\0" \
f4b36ea9	164	"dvimode=640x480MR-16@60\0" \
13d2cb98	165	"defaultdisplay=dvi\0" \
0cd31144	166	"mmcdev=0\0" \
13d2cb98 SS	167	"mmcroot=/dev/mmcblk0p2 rw\0" \
13d2cb98 SS	168	"mmcrootfstype=ext3 rootwait\0" \
3c6e50d7 SS	169	"nandroot=ubi0:rootfs ubi.mtd=4\0" \
3c6e50d7 SS	170	"nandrootfstype=ubifs\0" \
f4b36ea9 JK	171	"ramroot=/dev/ram0 rw ramdisk_size=65536 initrd=0x81000000,64M\0" \
f4b36ea9 JK	172	"ramrootfstype=ext2\0" \
f904cdbb	173	"mmcargs=setenv bootargs console=${console} " \
c522eac4	174	"${optargs} " \
5af32460	175	"mpurate=${mpurate} " \
b1660314	176	"buddy=${buddy} "\
c522eac4	177	"camera=${camera} "\
13d2cb98 SS	178	"vram=${vram} " \
13d2cb98 SS	179	"omapfb.mode=dvi:${dvimode} " \
13d2cb98 SS	180	"omapdss.def_disp=${defaultdisplay} " \
	181	"root=${mmcroot} " \
	182	"rootfstype=${mmcrootfstype}\0" \
f904cdbb	183	"nandargs=setenv bootargs console=${console} " \
c522eac4	184	"${optargs} " \
5af32460	185	"mpurate=${mpurate} " \
b1660314	186	"buddy=${buddy} "\
c522eac4	187	"camera=${camera} "\
13d2cb98 SS	188	"vram=${vram} " \
13d2cb98 SS	189	"omapfb.mode=dvi:${dvimode} " \
13d2cb98 SS	190	"omapdss.def_disp=${defaultdisplay} " \
	191	"root=${nandroot} " \
	192	"rootfstype=${nandrootfstype}\0" \
2ade496f NM	193	"findfdt=" \
	194	"if test $beaglerev = AxBx; then " \
	195	"setenv fdtfile omap3-beagle.dtb; fi; " \
	196	"if test $beaglerev = Cx; then " \
	197	"setenv fdtfile omap3-beagle.dtb; fi; " \
5c9038b6 RN	198	"if test $beaglerev = C4; then " \
5c9038b6 RN	199	"setenv fdtfile omap3-beagle.dtb; fi; " \
2ade496f	200	"if test $beaglerev = xMAB; then " \
3d47ffb9	201	"setenv fdtfile omap3-beagle-xm-ab.dtb; fi; " \
2ade496f NM	202	"if test $beaglerev = xMC; then " \
	203	"setenv fdtfile omap3-beagle-xm.dtb; fi; " \
	204	"if test $fdtfile = undefined; then " \
	205	"echo WARNING: Could not determine device tree to use; fi; \0" \
4fa2427c RN	206	"validatefdt=" \
	207	"if test $beaglerev = xMAB; then " \
	208	"if test ! -e mmc ${bootpart} ${bootdir}/${fdtfile}; then " \
	209	"setenv fdtfile omap3-beagle-xm.dtb; " \
	210	"fi; " \
	211	"fi; \0" \
f835ea71 JK	212	"bootenv=uEnv.txt\0" \
f835ea71 JK	213	"loadbootenv=fatload mmc ${mmcdev} ${loadaddr} ${bootenv}\0" \
cf073e49	214	"importbootenv=echo Importing environment from mmc ...; " \
44bd26fa	215	"env import -t -r $loadaddr $filesize\0" \
f4b36ea9 JK	216	"ramargs=setenv bootargs console=${console} " \
	217	"${optargs} " \
	218	"mpurate=${mpurate} " \
	219	"buddy=${buddy} "\
	220	"vram=${vram} " \
	221	"omapfb.mode=dvi:${dvimode} " \
	222	"omapdss.def_disp=${defaultdisplay} " \
	223	"root=${ramroot} " \
	224	"rootfstype=${ramrootfstype}\0" \
102ce9ea NM	225	"loadramdisk=load mmc ${bootpart} ${rdaddr} ${bootdir}/${ramdisk}\0" \
102ce9ea NM	226	"loadimage=load mmc ${bootpart} ${loadaddr} ${bootdir}/${bootfile}\0" \
09642269 GG	227	"loadbootscript=load mmc ${mmcdev} ${loadaddr} boot.scr\0" \
	228	"bootscript=echo Running bootscript from mmc${mmcdev} ...; " \
	229	"source ${loadaddr}\0" \
4fa2427c	230	"loadfdt=run validatefdt; load mmc ${bootpart} ${fdtaddr} ${bootdir}/${fdtfile}\0" \
f904cdbb DB	231	"mmcboot=echo Booting from mmc ...; " \
	232	"run mmcargs; " \
	233	"bootm ${loadaddr}\0" \
ea70690d NM	234	"mmcbootz=echo Booting with DT from mmc${mmcdev} ...; " \
	235	"run mmcargs; " \
	236	"bootz ${loadaddr} - ${fdtaddr}\0" \
f904cdbb DB	237	"nandboot=echo Booting from nand ...; " \
	238	"run nandargs; " \
	239	"nand read ${loadaddr} 280000 400000; " \
	240	"bootm ${loadaddr}\0" \
f4b36ea9 JK	241	"ramboot=echo Booting from ramdisk ...; " \
	242	"run ramargs; " \
	243	"bootm ${loadaddr}\0" \
aae58b95 JF	244	"userbutton=if gpio input 173; then run userbutton_xm; " \
	245	"else run userbutton_nonxm; fi;\0" \
	246	"userbutton_xm=gpio input 4;\0" \
c721fd6e GG	247	"userbutton_nonxm=gpio input 7;\0" \
c721fd6e GG	248	BOOTENV
f904cdbb	249
f904cdbb	250	/*
d3a513c2 MP	251	* OMAP3 has 12 GP timers, they can be driven by the system clock
	252	* (12/13/16.8/19.2/38.4MHz) or by 32KHz clock. We use 13MHz (V_SCLK).
	253	* This rate is divided by a local divisor.
f904cdbb	254	*/
d3a513c2	255	#define CONFIG_SYS_PTV 2 /* Divisor: 2^(PTV+1) => 8 */
f904cdbb	256
f904cdbb DB	257	/*-----------------------------------------------------------------------
	258	* FLASH and environment organization
	259	*/
	260
	261	/* ** PISMO SUPPORT * */
6cbec7b3	262	#if defined(CONFIG_CMD_NAND)
222a3113	263	#define CONFIG_SYS_FLASH_BASE NAND_BASE
6cbec7b3	264	#endif
f904cdbb DB	265
	266	/* Monitor at start of flash */
	267	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
	268	#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP
	269
	270	#define CONFIG_ENV_IS_IN_NAND 1
df4dbb5d	271	#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
f904cdbb DB	272	#define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */
	273	#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
	274
6cbec7b3 LC	275	#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
6cbec7b3 LC	276	#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
f904cdbb DB	277	#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
f904cdbb DB	278
53736baa DB	279	#define CONFIG_OMAP3_SPI
53736baa DB	280
75c57a35	281	/* Defines for SPL */
75c57a35	282	#define CONFIG_SPL_OMAP3_ID_NAND
75c57a35 TR	283
75c57a35 TR	284	/* NAND boot config */
55f1b39f	285	#define CONFIG_SYS_NAND_BUSWIDTH_16BIT
75c57a35 TR	286	#define CONFIG_SYS_NAND_5_ADDR_CYCLE
	287	#define CONFIG_SYS_NAND_PAGE_COUNT 64
	288	#define CONFIG_SYS_NAND_PAGE_SIZE 2048
	289	#define CONFIG_SYS_NAND_OOBSIZE 64
	290	#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
	291	#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
	292	#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\
	293	10, 11, 12, 13}
	294	#define CONFIG_SYS_NAND_ECCSIZE 512
	295	#define CONFIG_SYS_NAND_ECCBYTES 3
3f719069	296	#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW
75c57a35	297	#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
434f2cfc	298	/* NAND: SPL falcon mode configs */
	299	#ifdef CONFIG_SPL_OS_BOOT
	300	#define CONFIG_CMD_SPL_NAND_OFS 0x240000
	301	#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
	302	#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
	303	#endif
75c57a35	304
f904cdbb	305	#endif /* __CONFIG_H */