[thirdparty/u-boot.git] / include / configs / pfla02.h

/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * Copyright (C) Stefano Babic <sbabic@denx.de>
 */


#ifndef __PCM058_CONFIG_H
#define __PCM058_CONFIG_H

#ifdef CONFIG_SPL
#define CONFIG_SYS_SPI_U_BOOT_OFFS	(64 * 1024)
#include "imx6_spl.h"
#endif

#include "mx6_common.h"

/* Thermal */
#define CONFIG_IMX_THERMAL

/* Serial */
#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE	       UART4_BASE
#define CONSOLE_DEV		"ttymxc3"

/* Early setup */


/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN		(8 * SZ_1M)

/* Ethernet */
#define IMX_FEC_BASE			ENET_BASE_ADDR
#define CONFIG_FEC_XCV_TYPE		RGMII
#define CONFIG_ETHPRIME			"FEC"
#define CONFIG_FEC_MXC_PHYADDR		3

/* SPI Flash */
#define CONFIG_SF_DEFAULT_BUS		2
#define CONFIG_SF_DEFAULT_CS		0
#define CONFIG_SF_DEFAULT_SPEED		20000000
#define CONFIG_SF_DEFAULT_MODE		SPI_MODE_0

/* I2C Configs */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 0 */
#define CONFIG_SYS_I2C_SPEED		  100000

#ifndef CONFIG_SPL_BUILD
#define CONFIG_CMD_NAND
/* Enable NAND support */
#define CONFIG_CMD_NAND_TRIMFFS
#define CONFIG_SYS_MAX_NAND_DEVICE	1
#define CONFIG_SYS_NAND_BASE		0x40000000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_ONFI_DETECTION
#endif

/* DMA stuff, needed for GPMI/MXS NAND support */

/* Filesystem support */

/* Various command support */

/* Physical Memory Map */
#define PHYS_SDRAM                     MMDC0_ARB_BASE_ADDR

#define CONFIG_SYS_SDRAM_BASE          PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR       IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE       IRAM_SIZE

#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

/* MMC Configs */
#define CONFIG_SYS_FSL_ESDHC_ADDR	0
#define CONFIG_SYS_FSL_USDHC_NUM	2

/* Environment organization */
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SIZE                (16 * 1024)
#define CONFIG_ENV_OFFSET		(1024 * SZ_1K)
#define CONFIG_ENV_SECT_SIZE		(64 * SZ_1K)
#define CONFIG_ENV_SPI_BUS             CONFIG_SF_DEFAULT_BUS
#define CONFIG_ENV_SPI_CS              CONFIG_SF_DEFAULT_CS
#define CONFIG_ENV_SPI_MODE            CONFIG_SF_DEFAULT_MODE
#define CONFIG_ENV_SPI_MAX_HZ          CONFIG_SF_DEFAULT_SPEED
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
#define CONFIG_ENV_OFFSET_REDUND       (CONFIG_ENV_OFFSET + \
						CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND         CONFIG_ENV_SIZE

#ifdef CONFIG_ENV_IS_IN_NAND
#define CONFIG_ENV_OFFSET              (0x1E0000)
#define CONFIG_ENV_SECT_SIZE           (128 * SZ_1K)
#endif

/* Default environment */
#define CONFIG_EXTRA_ENV_SETTINGS \
	"addcons=setenv bootargs ${bootargs} "				\
		"console=${console},${baudrate}\0"			\
	"addip=setenv bootargs ${bootargs} "				\
		"ip=${ipaddr}:${serverip}:${gatewayip}:"		\
		"${netmask}:${hostname}:${netdev}:off\0"		\
	"addmisc=setenv bootargs ${bootargs} ${miscargs}\0"		\
	"addmtd=run mtdnand;run mtdspi;"				\
		"setenv bootargs ${bootargs} ${mtdparts}\0"		\
	"mtdnand=setenv mtdparts mtdparts=gpmi-nand:"			\
		"40m(Kernels),400m(root),-(nand)\0"			\
	"mtdspi=setenv mtdparts ${mtdparts}"				\
		"';spi2.0:1024k(bootloader),"				\
			"64k(env1),64k(env2),-(rescue)'\0"		\
	"bootcmd=if test -n ${rescue};"					\
		"then run swupdate;fi;run nandboot;run swupdate\0"	\
	"bootfile=uImage\0"						\
	"bootimage=uImage\0"						\
	"console=ttymxc3\0"						\
	"fdt_addr_r=0x18000000\0"					\
	"fdt_file=pfla02.dtb\0"						\
	"fdt_high=0xffffffff\0"						\
	"initrd_high=0xffffffff\0"					\
	"kernel_addr_r=" __stringify(CONFIG_LOADADDR) "\0"		\
	"miscargs=panic=1 quiet\0"					\
	"mmcargs=setenv bootargs root=${mmcroot} rw rootwait\0"		\
	"mmcboot=if run mmcload;then "					\
		"run mmcargs addcons addmisc;"				\
			"bootm;fi\0"					\
	"mmcload=mmc rescan;"						\
		"load mmc 0:${mmcpart} ${kernel_addr_r} boot/fitImage\0"\
	"mmcpart=1\0"							\
	"mmcroot=/dev/mmcblk0p1\0"					\
	"ubiroot=1\0"							\
	"nandargs=setenv bootargs ubi.mtd=1 "				\
		"root=ubi0:rootfs${ubiroot} rootfstype=ubifs\0"		\
	"nandboot=run mtdnand;ubi part nand0,0;"			\
		"ubi readvol ${kernel_addr_r} kernel${ubiroot};"	\
		"run nandargs addip addcons addmtd addmisc;"		\
		"bootm ${kernel_addr_r}\0"				\
	"net_nfs=tftp ${kernel_addr_r} ${board_name}/${bootfile};"	\
		"tftp ${fdt_addr_r} ${board_name}/${fdt_file};"		\
		"run nfsargs addip addcons addmtd addmisc;"		\
		"bootm ${kernel_addr_r} - ${fdt_addr_r}\0"		\
	"net_nfs_fit=tftp ${kernel_addr_r} ${board_name}/${fitfile};"	\
		"run nfsargs addip addcons addmtd addmisc;"		\
		"bootm ${kernel_addr_r}\0"				\
	"nfsargs=setenv bootargs root=/dev/nfs"				\
		" nfsroot=${serverip}:${nfsroot},v3 panic=1\0"		\
	"swupdate=setenv bootargs root=/dev/ram;"			\
		"run addip addcons addmtd addmisc;"			\
		"sf probe;"						\
		"sf read ${kernel_addr_r} 120000 600000;"		\
		"sf read 14000000 730000 800000;"			\
		"bootm ${kernel_addr_r} 14000000\0"

#endif
Commit	Line	Data
83d290c5	1	/* SPDX-License-Identifier: GPL-2.0+ */
83605d37 SB	2	/*
83605d37 SB	3	* Copyright (C) Stefano Babic <sbabic@denx.de>
83605d37 SB	4	*/
	5
	6
	7	#ifndef __PCM058_CONFIG_H
	8	#define __PCM058_CONFIG_H
	9
83605d37	10	#ifdef CONFIG_SPL
83605d37 SB	11	#define CONFIG_SYS_SPI_U_BOOT_OFFS (64 * 1024)
	12	#include "imx6_spl.h"
	13	#endif
	14
	15	#include "mx6_common.h"
	16
	17	/* Thermal */
	18	#define CONFIG_IMX_THERMAL
	19
	20	/* Serial */
	21	#define CONFIG_MXC_UART
	22	#define CONFIG_MXC_UART_BASE UART4_BASE
	23	#define CONSOLE_DEV "ttymxc3"
	24
	25	/* Early setup */
83605d37 SB	26
	27
	28	/* Size of malloc() pool */
	29	#define CONFIG_SYS_MALLOC_LEN (8 * SZ_1M)
	30
	31	/* Ethernet */
83605d37 SB	32	#define IMX_FEC_BASE ENET_BASE_ADDR
	33	#define CONFIG_FEC_XCV_TYPE RGMII
	34	#define CONFIG_ETHPRIME "FEC"
	35	#define CONFIG_FEC_MXC_PHYADDR 3
	36
83605d37	37	/* SPI Flash */
83605d37 SB	38	#define CONFIG_SF_DEFAULT_BUS 2
	39	#define CONFIG_SF_DEFAULT_CS 0
	40	#define CONFIG_SF_DEFAULT_SPEED 20000000
	41	#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
	42
	43	/* I2C Configs */
	44	#define CONFIG_SYS_I2C
	45	#define CONFIG_SYS_I2C_MXC
	46	#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 0 */
	47	#define CONFIG_SYS_I2C_SPEED 100000
	48
	49	#ifndef CONFIG_SPL_BUILD
	50	#define CONFIG_CMD_NAND
	51	/* Enable NAND support */
	52	#define CONFIG_CMD_NAND_TRIMFFS
83605d37 SB	53	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	54	#define CONFIG_SYS_NAND_BASE 0x40000000
	55	#define CONFIG_SYS_NAND_5_ADDR_CYCLE
	56	#define CONFIG_SYS_NAND_ONFI_DETECTION
	57	#endif
	58
	59	/* DMA stuff, needed for GPMI/MXS NAND support */
83605d37 SB	60
83605d37 SB	61	/* Filesystem support */
83605d37 SB	62
	63	/* Various command support */
	64
	65	/* Physical Memory Map */
83605d37 SB	66	#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
	67
	68	#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
	69	#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
	70	#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
	71
	72	#define CONFIG_SYS_INIT_SP_OFFSET \
	73	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	74	#define CONFIG_SYS_INIT_SP_ADDR \
	75	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
	76
	77	/* MMC Configs */
	78	#define CONFIG_SYS_FSL_ESDHC_ADDR 0
	79	#define CONFIG_SYS_FSL_USDHC_NUM 2
	80
	81	/* Environment organization */
	82	#define CONFIG_ENV_IS_IN_SPI_FLASH
	83	#define CONFIG_ENV_SIZE (16 * 1024)
	84	#define CONFIG_ENV_OFFSET (1024 * SZ_1K)
	85	#define CONFIG_ENV_SECT_SIZE (64 * SZ_1K)
	86	#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
	87	#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
	88	#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
	89	#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
	90	#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
	91	#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
	92	CONFIG_ENV_SECT_SIZE)
	93	#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
	94
	95	#ifdef CONFIG_ENV_IS_IN_NAND
	96	#define CONFIG_ENV_OFFSET (0x1E0000)
	97	#define CONFIG_ENV_SECT_SIZE (128 * SZ_1K)
	98	#endif
	99
	100	/* Default environment */
	101	#define CONFIG_EXTRA_ENV_SETTINGS \
	102	"addcons=setenv bootargs ${bootargs} " \
	103	"console=${console},${baudrate}\0" \
	104	"addip=setenv bootargs ${bootargs} " \
	105	"ip=${ipaddr}:${serverip}:${gatewayip}:" \
	106	"${netmask}:${hostname}:${netdev}:off\0" \
	107	"addmisc=setenv bootargs ${bootargs} ${miscargs}\0" \
	108	"addmtd=run mtdnand;run mtdspi;" \
	109	"setenv bootargs ${bootargs} ${mtdparts}\0" \
	110	"mtdnand=setenv mtdparts mtdparts=gpmi-nand:" \
	111	"40m(Kernels),400m(root),-(nand)\0" \
	112	"mtdspi=setenv mtdparts ${mtdparts}" \
	113	"';spi2.0:1024k(bootloader)," \
	114	"64k(env1),64k(env2),-(rescue)'\0" \
	115	"bootcmd=if test -n ${rescue};" \
	116	"then run swupdate;fi;run nandboot;run swupdate\0" \
	117	"bootfile=uImage\0" \
	118	"bootimage=uImage\0" \
	119	"console=ttymxc3\0" \
	120	"fdt_addr_r=0x18000000\0" \
	121	"fdt_file=pfla02.dtb\0" \
	122	"fdt_high=0xffffffff\0" \
	123	"initrd_high=0xffffffff\0" \
	124	"kernel_addr_r=" __stringify(CONFIG_LOADADDR) "\0" \
	125	"miscargs=panic=1 quiet\0" \
	126	"mmcargs=setenv bootargs root=${mmcroot} rw rootwait\0" \
	127	"mmcboot=if run mmcload;then " \
	128	"run mmcargs addcons addmisc;" \
	129	"bootm;fi\0" \
130	"mmcload=mmc rescan;" \
131	"load mmc 0:${mmcpart} ${kernel_addr_r} boot/fitImage\0"\
132	"mmcpart=1\0" \
133	"mmcroot=/dev/mmcblk0p1\0" \
134	"ubiroot=1\0" \
135	"nandargs=setenv bootargs ubi.mtd=1 " \
136	"root=ubi0:rootfs${ubiroot} rootfstype=ubifs\0" \
137	"nandboot=run mtdnand;ubi part nand0,0;" \
138	"ubi readvol ${kernel_addr_r} kernel${ubiroot};" \
139	"run nandargs addip addcons addmtd addmisc;" \
140	"bootm ${kernel_addr_r}\0" \
141	"net_nfs=tftp ${kernel_addr_r} ${board_name}/${bootfile};" \
142	"tftp ${fdt_addr_r} ${board_name}/${fdt_file};" \
143	"run nfsargs addip addcons addmtd addmisc;" \
144	"bootm ${kernel_addr_r} - ${fdt_addr_r}\0" \
145	"net_nfs_fit=tftp ${kernel_addr_r} ${board_name}/${fitfile};" \
146	"run nfsargs addip addcons addmtd addmisc;" \
147	"bootm ${kernel_addr_r}\0" \
148	"nfsargs=setenv bootargs root=/dev/nfs" \
149	" nfsroot=${serverip}:${nfsroot},v3 panic=1\0" \
150	"swupdate=setenv bootargs root=/dev/ram;" \
151	"run addip addcons addmtd addmisc;" \
152	"sf probe;" \
153	"sf read ${kernel_addr_r} 120000 600000;" \
154	"sf read 14000000 730000 800000;" \
155	"bootm ${kernel_addr_r} 14000000\0"
156
157	#endif