[people/ms/u-boot.git] / include / configs / sama5d4ek.h

/*
 * Configuration settings for the SAMA5D4EK board.
 *
 * Copyright (C) 2014 Atmel
 *		      Bo Shen <voice.shen@atmel.com>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#ifndef __CONFIG_H
#define __CONFIG_H

/* No NOR flash, this definition should put before common header */
#define CONFIG_SYS_NO_FLASH

#include "at91-sama5_common.h"

/* serial console */
#define CONFIG_ATMEL_USART
#define CONFIG_USART_BASE		ATMEL_BASE_USART3
#define	CONFIG_USART_ID			ATMEL_ID_USART3

/* SDRAM */
#define CONFIG_NR_DRAM_BANKS		1
#define CONFIG_SYS_SDRAM_BASE           ATMEL_BASE_DDRCS
#define CONFIG_SYS_SDRAM_SIZE		0x20000000

#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_INIT_SP_ADDR		0x210000
#else
#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
#endif

#define CONFIG_SYS_LOAD_ADDR		0x22000000 /* load address */

/* SerialFlash */
#define CONFIG_CMD_SF

#ifdef CONFIG_CMD_SF
#define CONFIG_ATMEL_SPI
#define CONFIG_ATMEL_SPI0
#define CONFIG_SPI_FLASH_ATMEL
#define CONFIG_SF_DEFAULT_BUS		0
#define CONFIG_SF_DEFAULT_CS		0
#define CONFIG_SF_DEFAULT_SPEED		30000000
#endif

/* NAND flash */
#define CONFIG_CMD_NAND

#ifdef CONFIG_CMD_NAND
#define CONFIG_NAND_ATMEL
#define CONFIG_SYS_MAX_NAND_DEVICE	1
#define CONFIG_SYS_NAND_BASE		ATMEL_BASE_CS3
/* our ALE is AD21 */
#define CONFIG_SYS_NAND_MASK_ALE	(1 << 21)
/* our CLE is AD22 */
#define CONFIG_SYS_NAND_MASK_CLE	(1 << 22)
#define CONFIG_SYS_NAND_ONFI_DETECTION
/* PMECC & PMERRLOC */
#define CONFIG_ATMEL_NAND_HWECC
#define CONFIG_ATMEL_NAND_HW_PMECC
#endif

/* MMC */
#define CONFIG_CMD_MMC

#ifdef CONFIG_CMD_MMC
#define CONFIG_MMC
#define CONFIG_GENERIC_MMC
#define CONFIG_GENERIC_ATMEL_MCI
#define ATMEL_BASE_MMCI			ATMEL_BASE_MCI1
#endif

/* USB */
#define CONFIG_CMD_USB

#ifdef CONFIG_CMD_USB
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_ATMEL
#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS	3
#define CONFIG_USB_STORAGE
#endif

/* USB device */
#define CONFIG_USB_GADGET
#define CONFIG_USB_GADGET_DUALSPEED
#define CONFIG_USB_GADGET_ATMEL_USBA
#define CONFIG_USB_ETHER
#define CONFIG_USB_ETH_RNDIS
#define CONFIG_USBNET_MANUFACTURER      "Atmel SAMA5D4EK"

#if defined(CONFIG_CMD_USB) || defined(CONFIG_CMD_MMC)
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
#endif

/* Ethernet Hardware */
#define CONFIG_MACB
#define CONFIG_RMII
#define CONFIG_NET_RETRY_COUNT		20
#define CONFIG_MACB_SEARCH_PHY

/* LCD */
#define CONFIG_LCD
#define LCD_BPP				LCD_COLOR16
#define LCD_OUTPUT_BPP                  18
#define CONFIG_LCD_LOGO
#define CONFIG_LCD_INFO
#define CONFIG_LCD_INFO_BELOW_LOGO
#define CONFIG_SYS_WHITE_ON_BLACK
#define CONFIG_ATMEL_HLCD
#define CONFIG_ATMEL_LCD_RGB565
#define CONFIG_SYS_CONSOLE_IS_IN_ENV

#ifdef CONFIG_SYS_USE_SERIALFLASH
/* bootstrap + u-boot + env + linux in serial flash */
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_SPI_BUS	CONFIG_SF_DEFAULT_BUS
#define CONFIG_ENV_SPI_CS	CONFIG_SF_DEFAULT_CS
#define CONFIG_ENV_OFFSET       0x10000
#define CONFIG_ENV_SIZE         0x10000
#define CONFIG_ENV_SECT_SIZE    0x1000
#define CONFIG_BOOTCOMMAND      "sf probe 0; " \
				"sf read 0x21000000 0xa0000 0x60000; " \
				"sf read 0x22000000 0x100000 0x300000; " \
				"bootz 0x22000000 - 0x21000000"
#elif CONFIG_SYS_USE_NANDFLASH
/* override the bootcmd, bootargs and other configuration for nandflash env*/
#elif CONFIG_SYS_USE_MMC
/* override the bootcmd, bootargs and other configuration for sd/mmc env */
#endif

/* SPL */
#define CONFIG_SPL_FRAMEWORK
#define CONFIG_SPL_TEXT_BASE		0x200000
#define CONFIG_SPL_MAX_SIZE		0x10000
#define CONFIG_SPL_BSS_START_ADDR	0x20000000
#define CONFIG_SPL_BSS_MAX_SIZE		0x80000
#define CONFIG_SYS_SPL_MALLOC_START	0x20080000
#define CONFIG_SYS_SPL_MALLOC_SIZE	0x80000

#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_GPIO_SUPPORT
#define CONFIG_SPL_SERIAL_SUPPORT

#define CONFIG_SPL_BOARD_INIT
#define CONFIG_SYS_MONITOR_LEN		(512 << 10)

#ifdef CONFIG_SYS_USE_MMC
#define CONFIG_SPL_LDSCRIPT		arch/arm/mach-at91/armv7/u-boot-spl.lds
#define CONFIG_SPL_MMC_SUPPORT
#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS	0x400
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME		"u-boot.img"
#define CONFIG_SPL_FAT_SUPPORT
#define CONFIG_SPL_LIBDISK_SUPPORT

#elif CONFIG_SYS_USE_NANDFLASH
#define CONFIG_SPL_NAND_SUPPORT
#define CONFIG_SPL_NAND_DRIVERS
#define CONFIG_SPL_NAND_BASE
#define CONFIG_PMECC_CAP		8
#define CONFIG_PMECC_SECTOR_SIZE	512
#define CONFIG_SYS_NAND_U_BOOT_OFFS	0x40000
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_SIZE	0x1000
#define CONFIG_SYS_NAND_PAGE_COUNT	64
#define CONFIG_SYS_NAND_OOBSIZE		224
#define CONFIG_SYS_NAND_BLOCK_SIZE	0x40000
#define CONFIG_SYS_NAND_BAD_BLOCK_POS	0x0
#define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER

#elif CONFIG_SYS_USE_SERIALFLASH
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_SPI_FLASH_SUPPORT
#define CONFIG_SPL_SPI_LOAD
#define CONFIG_SYS_SPI_U_BOOT_OFFS	0x20000

#endif
#endif
Commit	Line	Data
927b901b BS	1	/*
	2	* Configuration settings for the SAMA5D4EK board.
	3	*
	4	* Copyright (C) 2014 Atmel
	5	* Bo Shen <voice.shen@atmel.com>
	6	*
	7	* SPDX-License-Identifier: GPL-2.0+
	8	*/
	9
	10	#ifndef __CONFIG_H
	11	#define __CONFIG_H
	12
b2d387bc WJ	13	/* No NOR flash, this definition should put before common header */
b2d387bc WJ	14	#define CONFIG_SYS_NO_FLASH
927b901b	15
b2d387bc	16	#include "at91-sama5_common.h"
927b901b BS	17
	18	/* serial console */
	19	#define CONFIG_ATMEL_USART
	20	#define CONFIG_USART_BASE ATMEL_BASE_USART3
	21	#define CONFIG_USART_ID ATMEL_ID_USART3
	22
927b901b BS	23	/* SDRAM */
	24	#define CONFIG_NR_DRAM_BANKS 1
	25	#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_DDRCS
	26	#define CONFIG_SYS_SDRAM_SIZE 0x20000000
	27
5a4c9c22 BS	28	#ifdef CONFIG_SPL_BUILD
	29	#define CONFIG_SYS_INIT_SP_ADDR 0x210000
	30	#else
927b901b BS	31	#define CONFIG_SYS_INIT_SP_ADDR \
927b901b BS	32	(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
5a4c9c22	33	#endif
927b901b BS	34
	35	#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
	36
	37	/* SerialFlash */
	38	#define CONFIG_CMD_SF
	39
	40	#ifdef CONFIG_CMD_SF
	41	#define CONFIG_ATMEL_SPI
	42	#define CONFIG_ATMEL_SPI0
927b901b BS	43	#define CONFIG_SPI_FLASH_ATMEL
	44	#define CONFIG_SF_DEFAULT_BUS 0
	45	#define CONFIG_SF_DEFAULT_CS 0
	46	#define CONFIG_SF_DEFAULT_SPEED 30000000
	47	#endif
	48
	49	/* NAND flash */
	50	#define CONFIG_CMD_NAND
	51
	52	#ifdef CONFIG_CMD_NAND
	53	#define CONFIG_NAND_ATMEL
	54	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	55	#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3
	56	/* our ALE is AD21 */
	57	#define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
	58	/* our CLE is AD22 */
	59	#define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
	60	#define CONFIG_SYS_NAND_ONFI_DETECTION
	61	/* PMECC & PMERRLOC */
	62	#define CONFIG_ATMEL_NAND_HWECC
	63	#define CONFIG_ATMEL_NAND_HW_PMECC
	64	#endif
	65
	66	/* MMC */
	67	#define CONFIG_CMD_MMC
	68
	69	#ifdef CONFIG_CMD_MMC
	70	#define CONFIG_MMC
	71	#define CONFIG_GENERIC_MMC
	72	#define CONFIG_GENERIC_ATMEL_MCI
	73	#define ATMEL_BASE_MMCI ATMEL_BASE_MCI1
	74	#endif
	75
	76	/* USB */
	77	#define CONFIG_CMD_USB
	78
	79	#ifdef CONFIG_CMD_USB
	80	#define CONFIG_USB_EHCI
	81	#define CONFIG_USB_EHCI_ATMEL
	82	#define CONFIG_SYS_USB_EHCI_MAX_ROOT_PORTS 3
	83	#define CONFIG_USB_STORAGE
	84	#endif
	85
cd5ca303 BS	86	/* USB device */
	87	#define CONFIG_USB_GADGET
	88	#define CONFIG_USB_GADGET_DUALSPEED
	89	#define CONFIG_USB_GADGET_ATMEL_USBA
	90	#define CONFIG_USB_ETHER
	91	#define CONFIG_USB_ETH_RNDIS
	92	#define CONFIG_USBNET_MANUFACTURER "Atmel SAMA5D4EK"
	93
927b901b BS	94	#if defined(CONFIG_CMD_USB) \|\| defined(CONFIG_CMD_MMC)
	95	#define CONFIG_CMD_FAT
	96	#define CONFIG_DOS_PARTITION
	97	#endif
	98
	99	/* Ethernet Hardware */
	100	#define CONFIG_MACB
	101	#define CONFIG_RMII
	102	#define CONFIG_NET_RETRY_COUNT 20
	103	#define CONFIG_MACB_SEARCH_PHY
	104
	105	/* LCD */
	106	#define CONFIG_LCD
	107	#define LCD_BPP LCD_COLOR16
	108	#define LCD_OUTPUT_BPP 18
	109	#define CONFIG_LCD_LOGO
	110	#define CONFIG_LCD_INFO
	111	#define CONFIG_LCD_INFO_BELOW_LOGO
	112	#define CONFIG_SYS_WHITE_ON_BLACK
	113	#define CONFIG_ATMEL_HLCD
	114	#define CONFIG_ATMEL_LCD_RGB565
	115	#define CONFIG_SYS_CONSOLE_IS_IN_ENV
	116
	117	#ifdef CONFIG_SYS_USE_SERIALFLASH
	118	/* bootstrap + u-boot + env + linux in serial flash */
	119	#define CONFIG_ENV_IS_IN_SPI_FLASH
	120	#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
	121	#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
	122	#define CONFIG_ENV_OFFSET 0x10000
	123	#define CONFIG_ENV_SIZE 0x10000
	124	#define CONFIG_ENV_SECT_SIZE 0x1000
	125	#define CONFIG_BOOTCOMMAND "sf probe 0; " \
	126	"sf read 0x21000000 0xa0000 0x60000; " \
	127	"sf read 0x22000000 0x100000 0x300000; " \
	128	"bootz 0x22000000 - 0x21000000"
	129	#elif CONFIG_SYS_USE_NANDFLASH
dc018fef	130	/* override the bootcmd, bootargs and other configuration for nandflash env*/
927b901b	131	#elif CONFIG_SYS_USE_MMC
372ca03f	132	/* override the bootcmd, bootargs and other configuration for sd/mmc env */
927b901b BS	133	#endif
927b901b BS	134
5a4c9c22 BS	135	/* SPL */
	136	#define CONFIG_SPL_FRAMEWORK
	137	#define CONFIG_SPL_TEXT_BASE 0x200000
	138	#define CONFIG_SPL_MAX_SIZE 0x10000
	139	#define CONFIG_SPL_BSS_START_ADDR 0x20000000
	140	#define CONFIG_SPL_BSS_MAX_SIZE 0x80000
	141	#define CONFIG_SYS_SPL_MALLOC_START 0x20080000
	142	#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000
	143
	144	#define CONFIG_SPL_LIBCOMMON_SUPPORT
	145	#define CONFIG_SPL_LIBGENERIC_SUPPORT
	146	#define CONFIG_SPL_GPIO_SUPPORT
	147	#define CONFIG_SPL_SERIAL_SUPPORT
	148
	149	#define CONFIG_SPL_BOARD_INIT
	150	#define CONFIG_SYS_MONITOR_LEN (512 << 10)
	151
	152	#ifdef CONFIG_SYS_USE_MMC
993ea97e	153	#define CONFIG_SPL_LDSCRIPT arch/arm/mach-at91/armv7/u-boot-spl.lds
5a4c9c22 BS	154	#define CONFIG_SPL_MMC_SUPPORT
	155	#define CONFIG_SYS_U_BOOT_MAX_SIZE_SECTORS 0x400
	156	#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x200
	157	#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
	158	#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
	159	#define CONFIG_SPL_FAT_SUPPORT
	160	#define CONFIG_SPL_LIBDISK_SUPPORT
	161
	162	#elif CONFIG_SYS_USE_NANDFLASH
	163	#define CONFIG_SPL_NAND_SUPPORT
	164	#define CONFIG_SPL_NAND_DRIVERS
	165	#define CONFIG_SPL_NAND_BASE
	166	#define CONFIG_PMECC_CAP 8
	167	#define CONFIG_PMECC_SECTOR_SIZE 512
	168	#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x40000
	169	#define CONFIG_SYS_NAND_5_ADDR_CYCLE
	170	#define CONFIG_SYS_NAND_PAGE_SIZE 0x1000
	171	#define CONFIG_SYS_NAND_PAGE_COUNT 64
	172	#define CONFIG_SYS_NAND_OOBSIZE 224
	173	#define CONFIG_SYS_NAND_BLOCK_SIZE 0x40000
	174	#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0x0
	175	#define CONFIG_SPL_GENERATE_ATMEL_PMECC_HEADER
	176
	177	#elif CONFIG_SYS_USE_SERIALFLASH
	178	#define CONFIG_SPL_SPI_SUPPORT
	179	#define CONFIG_SPL_SPI_FLASH_SUPPORT
	180	#define CONFIG_SPL_SPI_LOAD
	181	#define CONFIG_SYS_SPI_U_BOOT_OFFS 0x20000
	182
	183	#endif
927b901b	184	#endif