[thirdparty/u-boot.git] / include / configs / topic_miami.h

/* SPDX-License-Identifier: GPL-2.0+ */
/*
 * (C) Copyright 2014 Topic Embedded Products
 *
 * Configuration for Zynq Evaluation and Development Board - Miami
 * See zynq-common.h for Zynq common configs
 */

#ifndef __CONFIG_TOPIC_MIAMI_H
#define __CONFIG_TOPIC_MIAMI_H


/* Speed up boot time by ignoring the environment which we never used */

#include "zynq-common.h"

/* Fixup settings */

/* SPL settings */
#undef CONFIG_SPL_ETH_SUPPORT
#undef CONFIG_SPL_MAX_FOOTPRINT
#define CONFIG_SPL_MAX_FOOTPRINT	CONFIG_SYS_SPI_U_BOOT_OFFS
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME     "u-boot.img"

/* sspi command isn't useful */
#undef CONFIG_CMD_SPI

/* No useful gpio */
#undef CONFIG_ZYNQ_GPIO
#undef CONFIG_CMD_GPIO

/* No falcon support */
#undef CONFIG_SPL_OS_BOOT
#undef CONFIG_SPL_FPGA_SUPPORT

/* FPGA commands that we don't use */

/* Extras */

/* Faster flash, ours may run at 108 MHz */
#undef CONFIG_SPI_FLASH_WINBOND

/* Setup proper boot sequences for Miami boards */

#if defined(CONFIG_USB)
# define EXTRA_ENV_USB \
	"usbreset=i2c dev 1 && i2c mw 41 1 ff && i2c mw 41 3 fe && "\
		"i2c mw 41 1 fe && i2c mw 41 1 ff\0" \
	"usbboot=run usbreset && if usb start; then " \
		"echo Booting from USB... && " \
		"if load usb 0 0x1900000 ${bootscript}; then "\
		"source 0x1900000; fi; " \
		"load usb 0 ${kernel_addr} ${kernel_image} && " \
		"load usb 0 ${devicetree_addr} ${devicetree_image} && " \
		"load usb 0 ${ramdisk_load_address} ${ramdisk_image} && " \
		"bootm ${kernel_addr} ${ramdisk_load_address} "\
			"${devicetree_addr}; " \
	"fi\0"
  /* Note that addresses here should match the addresses in the env */
# undef DFU_ALT_INFO
# define DFU_ALT_INFO \
	"dfu_alt_info=" \
	"uImage ram 0x2080000 0x500000;" \
	"devicetree.dtb ram 0x2000000 0x20000;" \
	"uramdisk.image.gz ram 0x4000000 0x10000000\0" \
	"dfu_ram=run usbreset && dfu 0 ram 0\0" \
	"thor_ram=run usbreset && thordown 0 ram 0\0"
#else
# define EXTRA_ENV_USB
#endif

#undef CONFIG_EXTRA_ENV_SETTINGS
#define CONFIG_EXTRA_ENV_SETTINGS	\
	"kernel_image=uImage\0"	\
	"kernel_addr=0x2080000\0" \
	"ramdisk_image=uramdisk.image.gz\0"	\
	"ramdisk_load_address=0x4000000\0"	\
	"devicetree_image=devicetree.dtb\0"	\
	"devicetree_addr=0x2000000\0"	\
	"bitstream_image=fpga.bin\0"	\
	"bootscript=autorun.scr\0" \
	"loadbit_addr=0x100000\0"	\
	"loadbootenv_addr=0x2000000\0" \
	"kernel_size=0x440000\0"	\
	"devicetree_size=0x10000\0"	\
	"boot_size=0xF00000\0"	\
	"fdt_high=0x20000000\0"	\
	"initrd_high=0x20000000\0"	\
	"mmc_loadbit=echo Loading bitstream from SD/MMC/eMMC to RAM.. && " \
		"mmcinfo && " \
		"load mmc 0 ${loadbit_addr} ${bitstream_image} && " \
		"fpga load 0 ${loadbit_addr} ${filesize}\0" \
	"qspiboot=echo Booting from QSPI flash... && " \
		"sf probe && " \
		"sf read ${devicetree_addr} 0xA0000 ${devicetree_size} && " \
		"sf read ${kernel_addr} 0xC0000 ${kernel_size} && " \
		"bootm ${kernel_addr} - ${devicetree_addr}\0" \
	"sdboot=if mmcinfo; then " \
			"setenv bootargs console=ttyPS0,115200 " \
				"root=/dev/mmcblk0p2 rw rootfstype=ext4 " \
				"rootwait quiet ; " \
			"load mmc 0 ${kernel_addr} ${kernel_image}&& " \
			"load mmc 0 ${devicetree_addr} ${devicetree_image}&& " \
			"bootm ${kernel_addr} - ${devicetree_addr}; " \
		"fi\0" \
	EXTRA_ENV_USB \
	DFU_ALT_INFO

#undef CONFIG_BOOTCOMMAND
#define CONFIG_BOOTCOMMAND	"if mmcinfo; then " \
	"if fatload mmc 0 0x1900000 ${bootscript}; then source 0x1900000; " \
	"fi; fi; run $modeboot"
#undef CONFIG_DISPLAY_BOARDINFO

#endif /* __CONFIG_TOPIC_MIAMI_H */
Commit	Line	Data
83d290c5	1	/* SPDX-License-Identifier: GPL-2.0+ */
2d48caa4 ML	2	/*
	3	* (C) Copyright 2014 Topic Embedded Products
	4	*
	5	* Configuration for Zynq Evaluation and Development Board - Miami
	6	* See zynq-common.h for Zynq common configs
2d48caa4 ML	7	*/
	8
	9	#ifndef __CONFIG_TOPIC_MIAMI_H
	10	#define __CONFIG_TOPIC_MIAMI_H
	11
2d48caa4 ML	12
2d48caa4 ML	13	/* Speed up boot time by ignoring the environment which we never used */
2d48caa4 ML	14
	15	#include "zynq-common.h"
	16
	17	/* Fixup settings */
2d48caa4 ML	18
	19	/* SPL settings */
	20	#undef CONFIG_SPL_ETH_SUPPORT
2d48caa4 ML	21	#undef CONFIG_SPL_MAX_FOOTPRINT
	22	#define CONFIG_SPL_MAX_FOOTPRINT CONFIG_SYS_SPI_U_BOOT_OFFS
	23	#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
	24
	25	/* sspi command isn't useful */
	26	#undef CONFIG_CMD_SPI
	27
	28	/* No useful gpio */
	29	#undef CONFIG_ZYNQ_GPIO
	30	#undef CONFIG_CMD_GPIO
	31
	32	/* No falcon support */
	33	#undef CONFIG_SPL_OS_BOOT
	34	#undef CONFIG_SPL_FPGA_SUPPORT
	35
	36	/* FPGA commands that we don't use */
2d48caa4 ML	37
2d48caa4 ML	38	/* Extras */
2d48caa4 ML	39
2d48caa4 ML	40	/* Faster flash, ours may run at 108 MHz */
2d48caa4	41	#undef CONFIG_SPI_FLASH_WINBOND
2d48caa4 ML	42
	43	/* Setup proper boot sequences for Miami boards */
	44
	45	#if defined(CONFIG_USB)
	46	# define EXTRA_ENV_USB \
	47	"usbreset=i2c dev 1 && i2c mw 41 1 ff && i2c mw 41 3 fe && "\
	48	"i2c mw 41 1 fe && i2c mw 41 1 ff\0" \
	49	"usbboot=run usbreset && if usb start; then " \
	50	"echo Booting from USB... && " \
	51	"if load usb 0 0x1900000 ${bootscript}; then "\
	52	"source 0x1900000; fi; " \
	53	"load usb 0 ${kernel_addr} ${kernel_image} && " \
	54	"load usb 0 ${devicetree_addr} ${devicetree_image} && " \
	55	"load usb 0 ${ramdisk_load_address} ${ramdisk_image} && " \
	56	"bootm ${kernel_addr} ${ramdisk_load_address} "\
	57	"${devicetree_addr}; " \
	58	"fi\0"
	59	/* Note that addresses here should match the addresses in the env */
	60	# undef DFU_ALT_INFO
	61	# define DFU_ALT_INFO \
	62	"dfu_alt_info=" \
	63	"uImage ram 0x2080000 0x500000;" \
	64	"devicetree.dtb ram 0x2000000 0x20000;" \
	65	"uramdisk.image.gz ram 0x4000000 0x10000000\0" \
	66	"dfu_ram=run usbreset && dfu 0 ram 0\0" \
	67	"thor_ram=run usbreset && thordown 0 ram 0\0"
	68	#else
	69	# define EXTRA_ENV_USB
	70	#endif
	71
2d48caa4 ML	72	#undef CONFIG_EXTRA_ENV_SETTINGS
	73	#define CONFIG_EXTRA_ENV_SETTINGS \
	74	"kernel_image=uImage\0" \
	75	"kernel_addr=0x2080000\0" \
	76	"ramdisk_image=uramdisk.image.gz\0" \
	77	"ramdisk_load_address=0x4000000\0" \
	78	"devicetree_image=devicetree.dtb\0" \
	79	"devicetree_addr=0x2000000\0" \
	80	"bitstream_image=fpga.bin\0" \
	81	"bootscript=autorun.scr\0" \
	82	"loadbit_addr=0x100000\0" \
	83	"loadbootenv_addr=0x2000000\0" \
1520fe60	84	"kernel_size=0x440000\0" \
2d48caa4 ML	85	"devicetree_size=0x10000\0" \
	86	"boot_size=0xF00000\0" \
	87	"fdt_high=0x20000000\0" \
	88	"initrd_high=0x20000000\0" \
	89	"mmc_loadbit=echo Loading bitstream from SD/MMC/eMMC to RAM.. && " \
	90	"mmcinfo && " \
	91	"load mmc 0 ${loadbit_addr} ${bitstream_image} && " \
	92	"fpga load 0 ${loadbit_addr} ${filesize}\0" \
	93	"qspiboot=echo Booting from QSPI flash... && " \
	94	"sf probe && " \
	95	"sf read ${devicetree_addr} 0xA0000 ${devicetree_size} && " \
	96	"sf read ${kernel_addr} 0xC0000 ${kernel_size} && " \
	97	"bootm ${kernel_addr} - ${devicetree_addr}\0" \
	98	"sdboot=if mmcinfo; then " \
	99	"setenv bootargs console=ttyPS0,115200 " \
	100	"root=/dev/mmcblk0p2 rw rootfstype=ext4 " \
	101	"rootwait quiet ; " \
	102	"load mmc 0 ${kernel_addr} ${kernel_image}&& " \
	103	"load mmc 0 ${devicetree_addr} ${devicetree_image}&& " \
	104	"bootm ${kernel_addr} - ${devicetree_addr}; " \
	105	"fi\0" \
	106	EXTRA_ENV_USB \
	107	DFU_ALT_INFO
	108
	109	#undef CONFIG_BOOTCOMMAND
	110	#define CONFIG_BOOTCOMMAND "if mmcinfo; then " \
	111	"if fatload mmc 0 0x1900000 ${bootscript}; then source 0x1900000; " \
	112	"fi; fi; run $modeboot"
	113	#undef CONFIG_DISPLAY_BOARDINFO
	114
2d48caa4	115	#endif /* __CONFIG_TOPIC_MIAMI_H */