]>
Commit | Line | Data |
---|---|---|
53633a89 TR |
1 | // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) |
2 | /* | |
3 | * Copyright (C) STMicroelectronics 2019 - All Rights Reserved | |
4 | * Author: Alexandre Torgue <alexandre.torgue@st.com> for STMicroelectronics. | |
5 | */ | |
6 | ||
7 | #include <dt-bindings/gpio/gpio.h> | |
8 | #include <dt-bindings/mfd/st,stpmic1.h> | |
9 | ||
10 | / { | |
11 | aliases { | |
12 | serial0 = &uart4; | |
13 | serial1 = &usart3; | |
14 | serial2 = &uart7; | |
15 | }; | |
16 | ||
17 | memory@c0000000 { | |
18 | device_type = "memory"; | |
19 | reg = <0xc0000000 0x20000000>; | |
20 | }; | |
21 | ||
22 | reserved-memory { | |
23 | #address-cells = <1>; | |
24 | #size-cells = <1>; | |
25 | ranges; | |
26 | ||
27 | mcuram2: mcuram2@10000000 { | |
28 | compatible = "shared-dma-pool"; | |
29 | reg = <0x10000000 0x40000>; | |
30 | no-map; | |
31 | }; | |
32 | ||
33 | vdev0vring0: vdev0vring0@10040000 { | |
34 | compatible = "shared-dma-pool"; | |
35 | reg = <0x10040000 0x1000>; | |
36 | no-map; | |
37 | }; | |
38 | ||
39 | vdev0vring1: vdev0vring1@10041000 { | |
40 | compatible = "shared-dma-pool"; | |
41 | reg = <0x10041000 0x1000>; | |
42 | no-map; | |
43 | }; | |
44 | ||
45 | vdev0buffer: vdev0buffer@10042000 { | |
46 | compatible = "shared-dma-pool"; | |
47 | reg = <0x10042000 0x4000>; | |
48 | no-map; | |
49 | }; | |
50 | ||
51 | mcuram: mcuram@30000000 { | |
52 | compatible = "shared-dma-pool"; | |
53 | reg = <0x30000000 0x40000>; | |
54 | no-map; | |
55 | }; | |
56 | ||
57 | retram: retram@38000000 { | |
58 | compatible = "shared-dma-pool"; | |
59 | reg = <0x38000000 0x10000>; | |
60 | no-map; | |
61 | }; | |
62 | }; | |
63 | ||
64 | led { | |
65 | compatible = "gpio-leds"; | |
66 | led-blue { | |
67 | label = "heartbeat"; | |
68 | gpios = <&gpiod 11 GPIO_ACTIVE_HIGH>; | |
69 | linux,default-trigger = "heartbeat"; | |
70 | default-state = "off"; | |
71 | }; | |
72 | }; | |
73 | ||
74 | sound { | |
75 | compatible = "audio-graph-card"; | |
76 | label = "STM32MP15-DK"; | |
77 | routing = | |
78 | "Playback" , "MCLK", | |
79 | "Capture" , "MCLK", | |
80 | "MICL" , "Mic Bias"; | |
81 | dais = <&sai2a_port &sai2b_port &i2s2_port>; | |
82 | status = "okay"; | |
83 | }; | |
84 | ||
85 | vin: vin { | |
86 | compatible = "regulator-fixed"; | |
87 | regulator-name = "vin"; | |
88 | regulator-min-microvolt = <5000000>; | |
89 | regulator-max-microvolt = <5000000>; | |
90 | regulator-always-on; | |
91 | }; | |
92 | }; | |
93 | ||
94 | &adc { | |
95 | pinctrl-names = "default"; | |
96 | pinctrl-0 = <&adc12_usb_cc_pins_a>; | |
97 | vdd-supply = <&vdd>; | |
98 | vdda-supply = <&vdd>; | |
99 | vref-supply = <&vrefbuf>; | |
100 | status = "okay"; | |
101 | adc1: adc@0 { | |
102 | status = "okay"; | |
103 | /* | |
104 | * Type-C USB_PWR_CC1 & USB_PWR_CC2 on in18 & in19. | |
105 | * Use at least 5 * RC time, e.g. 5 * (Rp + Rd) * C: | |
106 | * 5 * (56 + 47kOhms) * 5pF => 2.5us. | |
107 | * Use arbitrary margin here (e.g. 5us). | |
108 | */ | |
109 | channel@18 { | |
110 | reg = <18>; | |
111 | st,min-sample-time-ns = <5000>; | |
112 | }; | |
113 | channel@19 { | |
114 | reg = <19>; | |
115 | st,min-sample-time-ns = <5000>; | |
116 | }; | |
117 | }; | |
118 | adc2: adc@100 { | |
119 | status = "okay"; | |
120 | /* USB Type-C CC1 & CC2 */ | |
121 | channel@18 { | |
122 | reg = <18>; | |
123 | st,min-sample-time-ns = <5000>; | |
124 | }; | |
125 | channel@19 { | |
126 | reg = <19>; | |
127 | st,min-sample-time-ns = <5000>; | |
128 | }; | |
129 | }; | |
130 | }; | |
131 | ||
132 | &cec { | |
133 | pinctrl-names = "default", "sleep"; | |
134 | pinctrl-0 = <&cec_pins_b>; | |
135 | pinctrl-1 = <&cec_sleep_pins_b>; | |
136 | status = "okay"; | |
137 | }; | |
138 | ||
139 | &crc1 { | |
140 | status = "okay"; | |
141 | }; | |
142 | ||
143 | &dts { | |
144 | status = "okay"; | |
145 | }; | |
146 | ||
147 | ðernet0 { | |
148 | status = "okay"; | |
149 | pinctrl-0 = <ðernet0_rgmii_pins_a>; | |
150 | pinctrl-1 = <ðernet0_rgmii_sleep_pins_a>; | |
151 | pinctrl-names = "default", "sleep"; | |
152 | phy-mode = "rgmii-id"; | |
153 | max-speed = <1000>; | |
154 | phy-handle = <&phy0>; | |
155 | ||
156 | mdio { | |
157 | #address-cells = <1>; | |
158 | #size-cells = <0>; | |
159 | compatible = "snps,dwmac-mdio"; | |
160 | phy0: ethernet-phy@0 { | |
161 | reg = <0>; | |
162 | }; | |
163 | }; | |
164 | }; | |
165 | ||
166 | &hash1 { | |
167 | status = "okay"; | |
168 | }; | |
169 | ||
170 | &i2c1 { | |
171 | pinctrl-names = "default", "sleep"; | |
172 | pinctrl-0 = <&i2c1_pins_a>; | |
173 | pinctrl-1 = <&i2c1_sleep_pins_a>; | |
174 | i2c-scl-rising-time-ns = <100>; | |
175 | i2c-scl-falling-time-ns = <7>; | |
176 | status = "okay"; | |
177 | /delete-property/dmas; | |
178 | /delete-property/dma-names; | |
179 | ||
180 | hdmi-transmitter@39 { | |
181 | compatible = "sil,sii9022"; | |
182 | reg = <0x39>; | |
183 | iovcc-supply = <&v3v3_hdmi>; | |
184 | cvcc12-supply = <&v1v2_hdmi>; | |
185 | reset-gpios = <&gpioa 10 GPIO_ACTIVE_LOW>; | |
186 | interrupts = <1 IRQ_TYPE_EDGE_FALLING>; | |
187 | interrupt-parent = <&gpiog>; | |
188 | #sound-dai-cells = <0>; | |
189 | status = "okay"; | |
190 | ||
191 | ports { | |
192 | #address-cells = <1>; | |
193 | #size-cells = <0>; | |
194 | ||
195 | port@0 { | |
196 | reg = <0>; | |
197 | sii9022_in: endpoint { | |
198 | remote-endpoint = <<dc_ep0_out>; | |
199 | }; | |
200 | }; | |
201 | ||
202 | port@3 { | |
203 | reg = <3>; | |
204 | sii9022_tx_endpoint: endpoint { | |
205 | remote-endpoint = <&i2s2_endpoint>; | |
206 | }; | |
207 | }; | |
208 | }; | |
209 | }; | |
210 | ||
211 | cs42l51: cs42l51@4a { | |
212 | compatible = "cirrus,cs42l51"; | |
213 | reg = <0x4a>; | |
214 | #sound-dai-cells = <0>; | |
215 | VL-supply = <&v3v3>; | |
216 | VD-supply = <&v1v8_audio>; | |
217 | VA-supply = <&v1v8_audio>; | |
218 | VAHP-supply = <&v1v8_audio>; | |
219 | reset-gpios = <&gpiog 9 GPIO_ACTIVE_LOW>; | |
220 | clocks = <&sai2a>; | |
221 | clock-names = "MCLK"; | |
222 | status = "okay"; | |
223 | ||
224 | cs42l51_port: port { | |
225 | #address-cells = <1>; | |
226 | #size-cells = <0>; | |
227 | ||
228 | cs42l51_tx_endpoint: endpoint@0 { | |
229 | reg = <0>; | |
230 | remote-endpoint = <&sai2a_endpoint>; | |
231 | frame-master = <&cs42l51_tx_endpoint>; | |
232 | bitclock-master = <&cs42l51_tx_endpoint>; | |
233 | }; | |
234 | ||
235 | cs42l51_rx_endpoint: endpoint@1 { | |
236 | reg = <1>; | |
237 | remote-endpoint = <&sai2b_endpoint>; | |
238 | frame-master = <&cs42l51_rx_endpoint>; | |
239 | bitclock-master = <&cs42l51_rx_endpoint>; | |
240 | }; | |
241 | }; | |
242 | }; | |
243 | }; | |
244 | ||
245 | &i2c4 { | |
246 | pinctrl-names = "default", "sleep"; | |
247 | pinctrl-0 = <&i2c4_pins_a>; | |
248 | pinctrl-1 = <&i2c4_sleep_pins_a>; | |
249 | i2c-scl-rising-time-ns = <185>; | |
250 | i2c-scl-falling-time-ns = <20>; | |
251 | clock-frequency = <400000>; | |
252 | status = "okay"; | |
253 | /* spare dmas for other usage */ | |
254 | /delete-property/dmas; | |
255 | /delete-property/dma-names; | |
256 | ||
257 | stusb1600@28 { | |
258 | compatible = "st,stusb1600"; | |
259 | reg = <0x28>; | |
260 | interrupts = <11 IRQ_TYPE_LEVEL_LOW>; | |
261 | interrupt-parent = <&gpioi>; | |
262 | pinctrl-names = "default"; | |
263 | pinctrl-0 = <&stusb1600_pins_a>; | |
264 | status = "okay"; | |
265 | vdd-supply = <&vin>; | |
266 | ||
267 | connector { | |
268 | compatible = "usb-c-connector"; | |
269 | label = "USB-C"; | |
270 | power-role = "dual"; | |
271 | typec-power-opmode = "default"; | |
272 | ||
273 | port { | |
274 | con_usbotg_hs_ep: endpoint { | |
275 | remote-endpoint = <&usbotg_hs_ep>; | |
276 | }; | |
277 | }; | |
278 | }; | |
279 | }; | |
280 | ||
281 | pmic: stpmic@33 { | |
282 | compatible = "st,stpmic1"; | |
283 | reg = <0x33>; | |
284 | interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>; | |
285 | interrupt-controller; | |
286 | #interrupt-cells = <2>; | |
287 | status = "okay"; | |
288 | ||
289 | regulators { | |
290 | compatible = "st,stpmic1-regulators"; | |
291 | buck1-supply = <&vin>; | |
292 | buck2-supply = <&vin>; | |
293 | buck3-supply = <&vin>; | |
294 | buck4-supply = <&vin>; | |
295 | ldo1-supply = <&v3v3>; | |
296 | ldo2-supply = <&vin>; | |
297 | ldo3-supply = <&vdd_ddr>; | |
298 | ldo4-supply = <&vin>; | |
299 | ldo5-supply = <&vin>; | |
300 | ldo6-supply = <&v3v3>; | |
301 | vref_ddr-supply = <&vin>; | |
302 | boost-supply = <&vin>; | |
303 | pwr_sw1-supply = <&bst_out>; | |
304 | pwr_sw2-supply = <&bst_out>; | |
305 | ||
306 | vddcore: buck1 { | |
307 | regulator-name = "vddcore"; | |
308 | regulator-min-microvolt = <1200000>; | |
309 | regulator-max-microvolt = <1350000>; | |
310 | regulator-always-on; | |
311 | regulator-initial-mode = <0>; | |
312 | regulator-over-current-protection; | |
313 | }; | |
314 | ||
315 | vdd_ddr: buck2 { | |
316 | regulator-name = "vdd_ddr"; | |
317 | regulator-min-microvolt = <1350000>; | |
318 | regulator-max-microvolt = <1350000>; | |
319 | regulator-always-on; | |
320 | regulator-initial-mode = <0>; | |
321 | regulator-over-current-protection; | |
322 | }; | |
323 | ||
324 | vdd: buck3 { | |
325 | regulator-name = "vdd"; | |
326 | regulator-min-microvolt = <3300000>; | |
327 | regulator-max-microvolt = <3300000>; | |
328 | regulator-always-on; | |
329 | st,mask-reset; | |
330 | regulator-initial-mode = <0>; | |
331 | regulator-over-current-protection; | |
332 | }; | |
333 | ||
334 | v3v3: buck4 { | |
335 | regulator-name = "v3v3"; | |
336 | regulator-min-microvolt = <3300000>; | |
337 | regulator-max-microvolt = <3300000>; | |
338 | regulator-always-on; | |
339 | regulator-over-current-protection; | |
340 | regulator-initial-mode = <0>; | |
341 | }; | |
342 | ||
343 | v1v8_audio: ldo1 { | |
344 | regulator-name = "v1v8_audio"; | |
345 | regulator-min-microvolt = <1800000>; | |
346 | regulator-max-microvolt = <1800000>; | |
347 | regulator-always-on; | |
348 | interrupts = <IT_CURLIM_LDO1 0>; | |
349 | }; | |
350 | ||
351 | v3v3_hdmi: ldo2 { | |
352 | regulator-name = "v3v3_hdmi"; | |
353 | regulator-min-microvolt = <3300000>; | |
354 | regulator-max-microvolt = <3300000>; | |
355 | regulator-always-on; | |
356 | interrupts = <IT_CURLIM_LDO2 0>; | |
357 | }; | |
358 | ||
359 | vtt_ddr: ldo3 { | |
360 | regulator-name = "vtt_ddr"; | |
361 | regulator-min-microvolt = <500000>; | |
362 | regulator-max-microvolt = <750000>; | |
363 | regulator-always-on; | |
364 | regulator-over-current-protection; | |
365 | }; | |
366 | ||
367 | vdd_usb: ldo4 { | |
368 | regulator-name = "vdd_usb"; | |
369 | interrupts = <IT_CURLIM_LDO4 0>; | |
370 | }; | |
371 | ||
372 | vdda: ldo5 { | |
373 | regulator-name = "vdda"; | |
374 | regulator-min-microvolt = <2900000>; | |
375 | regulator-max-microvolt = <2900000>; | |
376 | interrupts = <IT_CURLIM_LDO5 0>; | |
377 | regulator-boot-on; | |
378 | }; | |
379 | ||
380 | v1v2_hdmi: ldo6 { | |
381 | regulator-name = "v1v2_hdmi"; | |
382 | regulator-min-microvolt = <1200000>; | |
383 | regulator-max-microvolt = <1200000>; | |
384 | regulator-always-on; | |
385 | interrupts = <IT_CURLIM_LDO6 0>; | |
386 | }; | |
387 | ||
388 | vref_ddr: vref_ddr { | |
389 | regulator-name = "vref_ddr"; | |
390 | regulator-always-on; | |
391 | }; | |
392 | ||
393 | bst_out: boost { | |
394 | regulator-name = "bst_out"; | |
395 | interrupts = <IT_OCP_BOOST 0>; | |
396 | }; | |
397 | ||
398 | vbus_otg: pwr_sw1 { | |
399 | regulator-name = "vbus_otg"; | |
400 | interrupts = <IT_OCP_OTG 0>; | |
401 | }; | |
402 | ||
403 | vbus_sw: pwr_sw2 { | |
404 | regulator-name = "vbus_sw"; | |
405 | interrupts = <IT_OCP_SWOUT 0>; | |
406 | regulator-active-discharge = <1>; | |
407 | }; | |
408 | }; | |
409 | ||
410 | onkey { | |
411 | compatible = "st,stpmic1-onkey"; | |
412 | interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 0>; | |
413 | interrupt-names = "onkey-falling", "onkey-rising"; | |
414 | power-off-time-sec = <10>; | |
415 | status = "okay"; | |
416 | }; | |
417 | ||
418 | watchdog { | |
419 | compatible = "st,stpmic1-wdt"; | |
420 | status = "disabled"; | |
421 | }; | |
422 | }; | |
423 | }; | |
424 | ||
425 | &i2c5 { | |
426 | pinctrl-names = "default", "sleep"; | |
427 | pinctrl-0 = <&i2c5_pins_a>; | |
428 | pinctrl-1 = <&i2c5_sleep_pins_a>; | |
429 | i2c-scl-rising-time-ns = <185>; | |
430 | i2c-scl-falling-time-ns = <20>; | |
431 | clock-frequency = <400000>; | |
432 | /* spare dmas for other usage */ | |
433 | /delete-property/dmas; | |
434 | /delete-property/dma-names; | |
435 | status = "disabled"; | |
436 | }; | |
437 | ||
438 | &i2s2 { | |
439 | clocks = <&rcc SPI2>, <&rcc SPI2_K>, <&rcc PLL3_Q>, <&rcc PLL3_R>; | |
440 | clock-names = "pclk", "i2sclk", "x8k", "x11k"; | |
441 | pinctrl-names = "default", "sleep"; | |
442 | pinctrl-0 = <&i2s2_pins_a>; | |
443 | pinctrl-1 = <&i2s2_sleep_pins_a>; | |
444 | status = "okay"; | |
445 | ||
446 | i2s2_port: port { | |
447 | i2s2_endpoint: endpoint { | |
448 | remote-endpoint = <&sii9022_tx_endpoint>; | |
449 | dai-format = "i2s"; | |
450 | mclk-fs = <256>; | |
451 | }; | |
452 | }; | |
453 | }; | |
454 | ||
455 | &ipcc { | |
456 | status = "okay"; | |
457 | }; | |
458 | ||
459 | &iwdg2 { | |
460 | timeout-sec = <32>; | |
461 | status = "okay"; | |
462 | }; | |
463 | ||
464 | <dc { | |
465 | pinctrl-names = "default", "sleep"; | |
466 | pinctrl-0 = <<dc_pins_a>; | |
467 | pinctrl-1 = <<dc_sleep_pins_a>; | |
468 | status = "okay"; | |
469 | ||
470 | port { | |
471 | ltdc_ep0_out: endpoint { | |
472 | remote-endpoint = <&sii9022_in>; | |
473 | }; | |
474 | }; | |
475 | }; | |
476 | ||
477 | &m4_rproc { | |
478 | memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>, | |
479 | <&vdev0vring1>, <&vdev0buffer>; | |
480 | mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>, <&ipcc 3>; | |
481 | mbox-names = "vq0", "vq1", "shutdown", "detach"; | |
482 | interrupt-parent = <&exti>; | |
483 | interrupts = <68 1>; | |
484 | status = "okay"; | |
485 | }; | |
486 | ||
487 | &pwr_regulators { | |
488 | vdd-supply = <&vdd>; | |
489 | vdd_3v3_usbfs-supply = <&vdd_usb>; | |
490 | }; | |
491 | ||
492 | &rng1 { | |
493 | status = "okay"; | |
494 | }; | |
495 | ||
496 | &rtc { | |
497 | status = "okay"; | |
498 | }; | |
499 | ||
500 | &sai2 { | |
501 | clocks = <&rcc SAI2>, <&rcc PLL3_Q>, <&rcc PLL3_R>; | |
502 | clock-names = "pclk", "x8k", "x11k"; | |
503 | pinctrl-names = "default", "sleep"; | |
504 | pinctrl-0 = <&sai2a_pins_a>, <&sai2b_pins_b>; | |
505 | pinctrl-1 = <&sai2a_sleep_pins_a>, <&sai2b_sleep_pins_b>; | |
506 | status = "okay"; | |
507 | ||
508 | sai2a: audio-controller@4400b004 { | |
509 | #clock-cells = <0>; | |
510 | dma-names = "tx"; | |
511 | status = "okay"; | |
512 | ||
513 | sai2a_port: port { | |
514 | sai2a_endpoint: endpoint { | |
515 | remote-endpoint = <&cs42l51_tx_endpoint>; | |
516 | dai-format = "i2s"; | |
517 | mclk-fs = <256>; | |
518 | dai-tdm-slot-num = <2>; | |
519 | dai-tdm-slot-width = <32>; | |
520 | }; | |
521 | }; | |
522 | }; | |
523 | ||
524 | sai2b: audio-controller@4400b024 { | |
525 | dma-names = "rx"; | |
526 | st,sync = <&sai2a 2>; | |
527 | clocks = <&rcc SAI2_K>, <&sai2a>; | |
528 | clock-names = "sai_ck", "MCLK"; | |
529 | status = "okay"; | |
530 | ||
531 | sai2b_port: port { | |
532 | sai2b_endpoint: endpoint { | |
533 | remote-endpoint = <&cs42l51_rx_endpoint>; | |
534 | dai-format = "i2s"; | |
535 | mclk-fs = <256>; | |
536 | dai-tdm-slot-num = <2>; | |
537 | dai-tdm-slot-width = <32>; | |
538 | }; | |
539 | }; | |
540 | }; | |
541 | }; | |
542 | ||
543 | &sdmmc1 { | |
544 | pinctrl-names = "default", "opendrain", "sleep"; | |
545 | pinctrl-0 = <&sdmmc1_b4_pins_a>; | |
546 | pinctrl-1 = <&sdmmc1_b4_od_pins_a>; | |
547 | pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>; | |
548 | cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>; | |
549 | disable-wp; | |
550 | st,neg-edge; | |
551 | bus-width = <4>; | |
552 | vmmc-supply = <&v3v3>; | |
553 | status = "okay"; | |
554 | }; | |
555 | ||
556 | &sdmmc3 { | |
557 | pinctrl-names = "default", "opendrain", "sleep"; | |
558 | pinctrl-0 = <&sdmmc3_b4_pins_a>; | |
559 | pinctrl-1 = <&sdmmc3_b4_od_pins_a>; | |
560 | pinctrl-2 = <&sdmmc3_b4_sleep_pins_a>; | |
561 | broken-cd; | |
562 | st,neg-edge; | |
563 | bus-width = <4>; | |
564 | vmmc-supply = <&v3v3>; | |
565 | status = "disabled"; | |
566 | }; | |
567 | ||
568 | &timers1 { | |
569 | /* spare dmas for other usage */ | |
570 | /delete-property/dmas; | |
571 | /delete-property/dma-names; | |
572 | status = "disabled"; | |
573 | pwm { | |
574 | pinctrl-0 = <&pwm1_pins_a>; | |
575 | pinctrl-1 = <&pwm1_sleep_pins_a>; | |
576 | pinctrl-names = "default", "sleep"; | |
577 | status = "okay"; | |
578 | }; | |
579 | timer@0 { | |
580 | status = "okay"; | |
581 | }; | |
582 | }; | |
583 | ||
584 | &timers3 { | |
585 | /delete-property/dmas; | |
586 | /delete-property/dma-names; | |
587 | status = "disabled"; | |
588 | pwm { | |
589 | pinctrl-0 = <&pwm3_pins_a>; | |
590 | pinctrl-1 = <&pwm3_sleep_pins_a>; | |
591 | pinctrl-names = "default", "sleep"; | |
592 | status = "okay"; | |
593 | }; | |
594 | timer@2 { | |
595 | status = "okay"; | |
596 | }; | |
597 | }; | |
598 | ||
599 | &timers4 { | |
600 | /delete-property/dmas; | |
601 | /delete-property/dma-names; | |
602 | status = "disabled"; | |
603 | pwm { | |
604 | pinctrl-0 = <&pwm4_pins_a &pwm4_pins_b>; | |
605 | pinctrl-1 = <&pwm4_sleep_pins_a &pwm4_sleep_pins_b>; | |
606 | pinctrl-names = "default", "sleep"; | |
607 | status = "okay"; | |
608 | }; | |
609 | timer@3 { | |
610 | status = "okay"; | |
611 | }; | |
612 | }; | |
613 | ||
614 | &timers5 { | |
615 | /delete-property/dmas; | |
616 | /delete-property/dma-names; | |
617 | status = "disabled"; | |
618 | pwm { | |
619 | pinctrl-0 = <&pwm5_pins_a>; | |
620 | pinctrl-1 = <&pwm5_sleep_pins_a>; | |
621 | pinctrl-names = "default", "sleep"; | |
622 | status = "okay"; | |
623 | }; | |
624 | timer@4 { | |
625 | status = "okay"; | |
626 | }; | |
627 | }; | |
628 | ||
629 | &timers6 { | |
630 | /delete-property/dmas; | |
631 | /delete-property/dma-names; | |
632 | status = "disabled"; | |
633 | timer@5 { | |
634 | status = "okay"; | |
635 | }; | |
636 | }; | |
637 | ||
638 | &timers12 { | |
639 | /delete-property/dmas; | |
640 | /delete-property/dma-names; | |
641 | status = "disabled"; | |
642 | pwm { | |
643 | pinctrl-0 = <&pwm12_pins_a>; | |
644 | pinctrl-1 = <&pwm12_sleep_pins_a>; | |
645 | pinctrl-names = "default", "sleep"; | |
646 | status = "okay"; | |
647 | }; | |
648 | timer@11 { | |
649 | status = "okay"; | |
650 | }; | |
651 | }; | |
652 | ||
653 | &uart4 { | |
654 | pinctrl-names = "default", "sleep", "idle"; | |
655 | pinctrl-0 = <&uart4_pins_a>; | |
656 | pinctrl-1 = <&uart4_sleep_pins_a>; | |
657 | pinctrl-2 = <&uart4_idle_pins_a>; | |
658 | /delete-property/dmas; | |
659 | /delete-property/dma-names; | |
660 | status = "okay"; | |
661 | }; | |
662 | ||
663 | &uart7 { | |
664 | pinctrl-names = "default", "sleep", "idle"; | |
665 | pinctrl-0 = <&uart7_pins_c>; | |
666 | pinctrl-1 = <&uart7_sleep_pins_c>; | |
667 | pinctrl-2 = <&uart7_idle_pins_c>; | |
668 | /delete-property/dmas; | |
669 | /delete-property/dma-names; | |
670 | status = "disabled"; | |
671 | }; | |
672 | ||
673 | &usart3 { | |
674 | pinctrl-names = "default", "sleep", "idle"; | |
675 | pinctrl-0 = <&usart3_pins_c>; | |
676 | pinctrl-1 = <&usart3_sleep_pins_c>; | |
677 | pinctrl-2 = <&usart3_idle_pins_c>; | |
678 | uart-has-rtscts; | |
679 | status = "disabled"; | |
680 | }; | |
681 | ||
682 | &usbh_ehci { | |
53633a89 TR |
683 | status = "okay"; |
684 | #address-cells = <1>; | |
685 | #size-cells = <0>; | |
686 | /* onboard HUB */ | |
687 | hub@1 { | |
688 | compatible = "usb424,2514"; | |
689 | reg = <1>; | |
690 | vdd-supply = <&v3v3>; | |
691 | }; | |
692 | }; | |
693 | ||
694 | &usbotg_hs { | |
695 | phys = <&usbphyc_port1 0>; | |
696 | phy-names = "usb2-phy"; | |
697 | usb-role-switch; | |
698 | status = "okay"; | |
699 | ||
700 | port { | |
701 | usbotg_hs_ep: endpoint { | |
702 | remote-endpoint = <&con_usbotg_hs_ep>; | |
703 | }; | |
704 | }; | |
705 | }; | |
706 | ||
707 | &usbphyc { | |
708 | status = "okay"; | |
709 | }; | |
710 | ||
711 | &usbphyc_port0 { | |
712 | phy-supply = <&vdd_usb>; | |
713 | st,tune-hs-dc-level = <2>; | |
714 | st,enable-fs-rftime-tuning; | |
715 | st,enable-hs-rftime-reduction; | |
716 | st,trim-hs-current = <15>; | |
717 | st,trim-hs-impedance = <1>; | |
718 | st,tune-squelch-level = <3>; | |
719 | st,tune-hs-rx-offset = <2>; | |
720 | st,no-lsfs-sc; | |
721 | }; | |
722 | ||
723 | &usbphyc_port1 { | |
724 | phy-supply = <&vdd_usb>; | |
725 | st,tune-hs-dc-level = <2>; | |
726 | st,enable-fs-rftime-tuning; | |
727 | st,enable-hs-rftime-reduction; | |
728 | st,trim-hs-current = <15>; | |
729 | st,trim-hs-impedance = <1>; | |
730 | st,tune-squelch-level = <3>; | |
731 | st,tune-hs-rx-offset = <2>; | |
732 | st,no-lsfs-sc; | |
733 | }; | |
734 | ||
735 | &vrefbuf { | |
736 | regulator-min-microvolt = <2500000>; | |
737 | regulator-max-microvolt = <2500000>; | |
738 | vdda-supply = <&vdd>; | |
739 | status = "okay"; | |
740 | }; |